Minka Aire F539-BCW User manual

Brand: Minka Aire

Model: F539-BCW

Category: Household fans

Type: User manual

This manual is also suitable for

INSTRUCTION MANUAL WARRANTY CERTIFICATE

GREAT ROOM TRADITIONAL

GREAT ROOM TRADITIONALGREAT ROOM TRADITIONAL

Manual design and all elements of manual design are protected by U.S. Federal and/or State Law, including Patent, Trademark and/or Copyright Laws.

Minka-Aire

warrants to the original owner that this fan will be free from defects in material and workmanship for one

year from the date of purchase, excluding the motor. Minka-Aire

warrants to the original owner that the motor in this fan

shall be free from defects in This is a limited warranty. Minka-Aire

only obligation under this limited warranty is to replace

or repair, or refund the purchase price, in Minka-Aire

sole discretion without charge to the original owner, of the fan once Minka-Aire

confirms that

the fan has a defect covered by this limited warranty.

Call our customer service department at 1-800-307-3267 to obtain the name of the Minka-Aire

authorized dealer closest to your location, or

contact us through our web site, www.minkagroup.net and write to: Ask Mr. Minka if you have any questions or require further assistance.

To obtain warranty service, the owner should return the fan along with proof of purchase to a Minka-Aire

authorized dealer. The Minka-Aire

authorized dealer shall then, at its sole discretion: repair the fan, replace the fan, refund the purchase price less the amount directly attributable to

the consumer's prior usage of the fan, or if necessary instruct the consumer to contact Minka-Aire

directly for warranty service. Minka-Aire

will be

responsible for the cost of any repair, or replacement for any warranty service provided by a Minka-Aire

authorized dealer for product under

warranty.

You may also at your preference obtain warranty service by returning the fan directly to Minka-Aire

along with proof of purchase, your name

and return address, and a description of the claimed product defect. Pack carefully; damage sustained in return transit to Minka-Aire

will be the

original owner's responsibility. Original owner shall be responsible to pay all shipping charges. To obtain warranty service, you may return a fan that

proves to be defective during the warranty period to the following address:

Minka-Aire

- Warranty Service, 1151 W. Bradford Court, Corona, CA 92882

This warranty shall not apply to fans which have been damaged in any way, including improper installation, damage as a result of the removal

of the fan from the origial installation, or damage in shipping. This warranty shall not apply to fans which have been subjected to use for which the

fan was not designed. The purchaser of the fan shall be responsible for any cost of removing the old fan, installing a new fan, or any other costs.

This limited warranty is in lieu of all other express warranties. This limited warranty excludes all incidental and consequential damages, and

Minka-Aire

shall not under any circumstances be liable for incidental or consequential damages. Some States do not allow the exclusion of or

limitation of incidental or consequential damages, so the foregoing limitation or exclusion may not apply to you.

This warranty gives you specific legal rights, and you may also have other rights which vary from State to State. We encourage you to promptly

complete and return the enclosed warranty registration card. However, return of the warranty registration card is not a condition of this warranty.

Date Purchased Store Purchased Model No. F539 Serial No.

CONTENTS

1151W. Bradford Court, Corona CA 92882 For Customer Assistance Call: 1-800-307-3267

SAFETY FIRST 1

PACKAGE CONTENTS 2

BEGIN INSTALLATION 3

HANGING THE FAN 4

ELECTRICAL CONNECTIONS 5

INSTALLING THE WALL TRANSMITTER 6

ATTACHING THE FAN BLADES 8

ATTACHING THE SWITCH CUP 9

OPERATING THE REMOTE CONTROL/WALL CONTROL 10

MAINTENANCE 11

TROUBLESHOOTING 12

FINISHING THE INSTALLATION 7

SPECIFICATIONS 13

1. Before you begin installing the fan, shut power off at the circuit breaker of the fuse box.

2. Be cautious! Read all instructions and safety information before installing your new fan. Review accompanying assembly diagrams.

3. Make sure that all electrical connections comply with local codes, ordinances, or National Electrical Codes. Hire a qualified electrician or consult a

do-it-yourself wiring handbook if you are unfamiliar with installing electrical wiring.

4. Make sure the installation site you choose allows the fan blades to rotate without any obstructions. Allow a minimum clearance of 7 feet from

the floor and 18 inches from the tip of the blades to the wall.

5. NOTE: THIS CEILING FAN EXCEEDS THE MAXIMUM WEIGHT SPECIFIED BY UL FOR HANGING FROM A STANDARD OUTLET BOX. SPECIAL

REINFORCEMENT OF THE CEILING IS REQUIRED FOR INSTALLATION.

6. CAUTION: Use the wood screws provided for fan installation. The wood screws must go through the outlet box via the knock outs and secured

directly to the building joist.

7. After you install the fan, make sure that all mounting components are secured to prevent the fan from falling.

8. Do not insert anything into the fan blades while the fan is operating.

9. Turn the fan off and wait for the blades to stop completely before cleaning or performing any maintenance.

SAFETY FIRST

WARNING

SUPPORT DIRECTLY FROM BUILDING STRUCTURE.

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR OTHER PERSONAL INJURY. MOUNT FAN DIRECTLY TO THE BUILDING JOIST USING THE

WOOD SCREWS AND WASHERS PROVIDED WITH THE FAN. THE WOOD SCREWS MUST GO THROUGH THE OUTLET BOX VIA THE KNOCK

OUTS. CONSULT A QUALIFIED ELECTRICIAN IF IN DOUBT.

TO REDUCE THE RISK OF PERSONAL INJURY, DO NOT BEND THE BLADE HOLDERS WHILE INSTALLING, BALANCING THE BLADES, OR

CLEANING THE FAN. DO NOT INSERT FOREIGN OBJECTS BETWEEN ROTATING FAN BLADES.

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT USE THIS FAN WITH ANY SOLID-STATE SPEED CONTROL DEVICE.

TO REDUCE THE RISK OF FIRE OR ELECTRONIC SHOCK, THIS FAN ONLY CAN USE UC7067RY SOLID-STATE SPEED CONTROL WITH UC9040T

WALL CONTROL ONLY.

NOTE:The important safeguards and instructions appearing in this manual are not meant to cover all possible conditions and situations that may

occur. It must be understood that common sense, caution and care are factors which can not be built into this product. These factors must be

supplied by the person (s) installing, caring for and operating the unit.

NOTE: READ AND SAVE ALL INSTRUCTIONS!

1. Fan motor/housing

ass'y

2. Canopy

3. Switch Cup

4. Fan blade

5. Coupling cover

6. Blade bracket

7. Standard 6"downrod

assembly

8. Minimum 3-1/2" length

downrod (for close to

ceiling mounting only)

9a. Hanger bracket plate

9b. Hanger bracket

10. Balancing kit

11. Receiver with 6 wire

nuts

12a.Wall plate (includes 2

mounting screws)

12b.Wall control transmitter

(includes 2 mounting

screws)

A. Blade Attachment Hardware:

3/16"-14mmscrews(16

pcs.)

Fiber washers (16 pcs.)

B. Mounting Hardware:

M6.5X89mm wood

screws (3pcs)

Ø6.5X19mm Flat washer

(3pcs)

Star washer (3pcs)

3/16" spring washer

(3pcs)

Ø5X14mm Flat ashers (3

pcs.)

C. Bracket Attachment

Hardware:

1/4"-11mm screws (11

pcs.)

D. Wire Nut (3 pcs.)

PACKAGE CONTENTS

BEGIN INSTALLATION

MOUNTING OPTIONS

If there isn't an existing mounting box,then read the following instructions.Shut the

power off at the circuit breaker or fuse box.

NOTE: THIS CEILING FAN EXCEEDS THE MAXIMUM WEIGHT SPECIFIED BY UL FOR

HANGING FROM A STANDARD OUTLET BOX. SPECIAL REINFORCEMENT OF THE

CEILING IS REQUIRED FOR INSTALLATION.

Secure the ceiling fan's hanging bracket directly from the building structure via the

outlet box.

Figures 1,2 and 3 are examples of different ways to mount the outlet box.

Note:You may need a longer downrod to maintain proper blade clearance when

installing on a steep,sloped ceiling. Longer downrods are available from your Minka-

Aire

dealer.

To hang your fan where there is an existing fixture but no ceiling joist,you may need

to install a hanger bar as shown in Fig. 4 (available at your Minka-Aire

dealer).

Tools Required: Phillips screw driver; slotted screw driver;pliers;wire cutters; electrical tape.

CEILING JOIST

OUTLET BOX

CROSS BRACE

PARALLEL WOOD BRACE

(MIN. 2" THICK)

OUTLET

BOX

CEILING JOIST

OR CROSS BRACE

Fig.1

Fig.2

Fig.3

Fig.4

ANGLED CEILING

MAXIMUM 27

ANGLE

PROVIDE STRONG

SUPPORT

HANGER

OPENING

MUST

BE FACING

UP-SIDE

OUTLET BOX

HANGER BAR

(OPTIONAL)

CEILING

JOIST

HANGER

BRACKET

REMEMBER to turn off the power. Follow the steps below to hang your

fan properly;

Step 1. Remove two knock-outs from the outlet box to expose the joist.

(Fig. 5)

Step 2. Use the two wood screws and washers to secure the hanger bracket

plate directly to the building joist via the knock-out holes from the outlet

box. (Fig. 6)

CAUTION! THE HANGER BRACKET PLATE MUST BE INSTALLED DIRECTLY

TO THE BUILDING JOIST USING THE TWO WOOD SCREWS AND

WASHERS PROVIDED.

Step 3. Secure hanger bracket to hanger bracket plate using the two hex

nuts and washers provided, make sure nuts are securely tighten. (Fig. 7)

Step 4. Loosen the two Set Screws from the coupling. (Fig. 8)

Step 5. Remove the Hanger Ball from the Down Downrod Assembly by

loosening the Set Screw and removing the Cross Pin. Remove the Hitch Pin

and Lock Pin. (Fig. 9)

Step 6. Carefully feed fan wires up through the downrod. Insert the rod

into the coupling and tighten onto fan until the holes are aligned. Next

replace lock pin and hitch pin. Tighten the screws (Fig.10)

Step 7. Slip coupling cover and canopy onto downrod. Let canopy rest on

top of the coupling cover. Carefully reinstall hanger ball onto rod being

sure that cross pin isin correct position set screw on hanger ball istight and

wires are not twised. (Fig. 10)

Step 8. Now lift motor assembly into position and place downrod

ball into hanger bracket. Rotate until the check groove has dropped

into the registration slot and seats firmly. Rod should not rotate if this is

done correctly (Fig. 11)

HANGING THE FAN

WARNING: All of the parts, hardware and components such as the

hanger bracket and hanger ball have been provided for your safety

and the proper installation of your new ceiling fan. The use of other parts,

hardware or components not supplied by Minka Aire with the fan will

void the Minka Aire Warranty.

Fig.11

SET SCREW

OUTLET

BOX

OUTLET

BOX

KNOCK

OUT

Fig.8Fig.6

Fig.5

Fig.9Fig.7

Fig.10

HANGER

BRACKET

PLATE

STAR WASHERS

LOCK WASHERS

FLAT WASHERS

WOOD SCREWS

FLAT

WASHERS

SPRING

WASHERS

HEX NUTS

HANGER

BRACKET

REGISTRATION

SLOT

HITCH PIN

SET SCREW

CROSS PIN

HANGER

BALL

DOWNROD

LOCK PIN

CANOPY

LOCK PIN

HITCH PIN

SCREW

COUPLING

COVER

WARNING:To avoid possible electrical shock be sure electricity is

turned off at the main fuse or breaker box before wiring.

Step 1.Insert Receiver into Hanger Bracket with the flat side of the Receiver

facing the ceiling. (Fig. 13)

Step 2.Motor to Receiver Electrical Connections: Connect the WHITE

wire from the fan to the WHITE wire marked "TO MOTOR N" from the

Receiver. Connect the BLACK wire from the fan to the BLACK wire

marked "TO MOTOR L" from the Receiver. Connect the BLUE wire from

the fan to the BLUE wire marked "For Light" from the Receiver.

Note: If your ceiling fan features an UP Light: Connect the ORANGE wire

from the fan to the ORANGE wire marked "For Up Light" from the

Receiver. Otherwise disregard this step and proceed to secure all wire

connections with the plastic wire nuts provided. (Fig. 14 & 15)

Step 3. Receiver to House Supply Wires Electrical Connections: Connect the

WHITE wire (Neutral) from the outlet box to the WHITE wire marked "AC in

N" from the receiver. Connect the BLACK wire (Hot) from the outlet box to

the BLACK wire marked "AC in L" from the receiver. Secure all wire

connections with the plastic wire nuts provided. (Fig. 14 & 15)

ELECTRICAL CONNECTIONS

Note: The Aire Control System is equipped with a learning frequency

function which has 256 code cominations to prevent potential interference

from other remote units. The frequency on your Receiver and Transmitter units

have been preset at the factory. (Fig.12). No frequency change is necessary,

should you desire to install another fan within the same home or area with

a seperate frequency code please see the “frequency interference ” troub-

leshooting section of this instruction manual to learn how to change the

frequency.

After all splices are made, check to make

sure there are no loose strands. As an

additional precaution we suggest to secure

the plastic wire connectors to the wires

with electrical tape.

Note: Fan must be installed from a maximum

distance of 40 feet from the transmitting

unit for proper signal transmission between

the transmitting unit and the fan's receiving

unit.

Fig.13

Fig.12

Fig.14 Fig.15

RECEIVER

OUT LET

BOX

RECEIVER

FAN

DOWNROD

HANGER

BRACKET

RECEIVER

WALL

CONTROL

GROUND

GREEN

BLACK

Step 4. If your outlet box has a GROUND

wire (Green or Bare Copper) connect this

wire to the Hanger Ball and Hanger Bracket

Ground wires. If your outlet box does not

have a Ground Wire, then connect the

Hanger Ball and Hanger Bracket Ground

Wires together. Secure wire connection

with the plastic wire nut provided. (Fig. 14

& 15)

WARNING! HOOK UP "IN SERIES" ONLY. DO NOT CONNECT NEUTRAL SUPPLY WIRE

OF ELECTRIC CIRCUIT TO THE TRANSMITTER WALL SWITCH, DAMAGE TO THE

TRANSMITTER WALL SWITCH AND POSSIBLE FIRE COULD OCCUR.

Step 1.Remove the existing wall plate and switch from the wall outlet box.

Step 2.Make the electrical connections as shown in Fig.15. If your outlet box has a ground

wire (Green or Bare Copper) connect the Transmitter's ground wire directly to one of the

screws from the outlet box . Secure all wire connections with the plastic wire nuts provided.

Step 3.Carefully tuck the wire connections inside the outlet box. Use the screws provided to

secure the wall transmitter and wall plate to the outlet box. (Fig. 16)

NOTE: Your Aire Control System includes two sets of face and decorative plate color options.

The wall control comes with standard white faceplate attached. If you desire to replace it with

the lvory color faceplate included, use a small flat screw driver and gently pry it apart from the

top or bottom of the plate.

INSTALLING THE WALL TRANSMITTER

Fig.16

Step 1. Remove 1 of the 2 screws from the bottom of the hanger bracket and loosen the other

one half a turn from the screw head.

Step 2. Slide the canopy up towards the hanger bracket and place the key hole on the canopy

over the screw on the hanger bracket, turn canopy until it locks in place at the narrow section

of the key holes. (Fig. 17)

Step 3. Align the circular hole on canopy with the remaining hole on the hanger bracket, secure

by tightening the two set screws.

Note: Adjust the canopy screws as necessary until the canopy are snug.

FINISHING THE INSTALLATION

Fig.17

HANGER

BRACKET

OUTLET

BOX

HANGER

BALL

CANOPY

Step 1. Attach the fan blade to the blade bracket using the screws

provided. Tighten screws securely. Repeat for remaining blades.

(Fig. 18).

Step 2. Remove the rubber stops from the motor and discard.

Rotate the motor so that the screw holes are revealed through

the opening from the switch cup plate. Align holes in blade

bracket and motor and secure with proper screws and fiber

washers provided. Repeat process with the other blade brackets.

(Fig. 19).

ATTACHING THE FAN BLADES

Fig.18 Fig.19

BLADE BRACKET

FAN BLADE

SCREW

FIBER WASHER

FAN BLADE

SCREW

FAN

Step 1. Remove the screws from the switch cup plate. Connect the switch cup and fan

wire molex connectors, Place the switch cup over the switch cup plate and secure

with screws previously removed. (Fig.20).

NOTE: DO NOT PINCH WIRES BETWEEN THE SWITCH CUP AND THE SWITCH CUP

PLATE.

ATTACHING THE SWITCH CUP

Fig.20

CAP

SCREW

LIGHT KIT

MOLEX

A. Buttons:

These buttons are used to set the fan speeds

as follows;

= Low Speed

= Medium Speed

= High Speed

Button:

This button turns the fan off.

C. Button:

These buttons turn the light ON or OFF and also

control the brightness settings of the

light. The following instructions apply

to ceiling fans that feature a DOWN

light ( button) only or ceiling fans that

feature an UP light ( button) and a DOWN

light ( button) that are controlled

independent of each other;

Press and release the button for the desired light

to turn the light ON or OFF. Press and hold the

button to set the desired light brightness. The

light will cycle between bright and dim settings

as long as the button is pressed.

The light key has an automatic auto-resume

feature that allows the light to remain at the same

brightness as the last time it was turned off.

D. OFF-ON Slide Button (Wall Control Fans

Only) This button turns the power Off and On

to the Fan and Light(s).

E. Button: (Full Function Remote Control

Units Only) This button is used to change the

direction of the rotation of the blades; forward

for warm weather or reverse for warm

weather.

NOTE: If your Remote Control or Wall Control

does not have a "REV" button, Please look for a

slide reverse switch on the motor housing.

Remote Control fans only: Install the A23, 12v battery (included) . To prevent damage to transmitter remove the battery if not used for long

periods of time.

OPERATING THE REMOTE CONTROL/WALL CONTROL

Fig 21

Fig 22

SUMMER OPERATION

WINTER OPERATION

Speed settings for warm or cold weather depend

on factors such as room size, ceiling height and

number of fans.

NOTE: To change the direction of the rotation of

the blades the fan must be in operation mode.

Warm Weather (forward)

A DOWNWARD airflow creates a cooling effect

as shown in Figure 21. This allows you to set your

air conditioner on a warmer setting without

affecting your comfort.

Cool Weather (Reverse)

An UPWARD airflow moves warmer air off the

ceiling area as shown in Figure 22.This allows

you to set your heating unit on a cooler setting

without affecting your comfort.

Here are some suggestions to help you maintain your fan.

1. Because of the fan's matural novement,some connections may become

loose. Check the support connections,brackets, and blade attachments

twice a year. Make sure they are secure (It is not necessary to remove

fan from ceiling. )

2. Clean your fan periodically to help maintain its new appearance over

the years. Do not use water when cleaning. This could damage the

motor,or the wood,or possibly cause an electrical shock.

3. Use only a soft brush or lint-free cloth to avoid scratching the finish.

The plating is sealed with a lacquer to minimize discoloration or

tarnishing.

4. You can apply a light coat of furniture polish to the wood for

additional protection and enhanced beauty. Cover small scratches

with a light application of shoe polish.

5. There is no need to oil your fan. The motor has permanently

lubricated bearings.

6. All glass should be cleaned using lukewarm soapy water and a soft

cloth or sponge DO NOT IMMERSE GLASS IN HOT WATER DO NOT PUT

GLASS INTO AN AUTOMATIC DISHWASHER.

MAINTENANCE

WARNING

MAKE SURE THE POWER IS OFF AT THE ELECTRICAL PANEL BOX

BEFORE YOU ATTEMPT ANY REPAIRS. REFER TO THE SECTION,

"MAKING ELECTRICAL CONNECTIONS".

Page is loading ...

Minka Aire F539-BCW User manual

Brand: Minka Aire

Model: F539-BCW

Category: Household fans

Type: User manual

This manual is also suitable for

Download PDF

report

Minka Aire F539-BCW User manual

This manual is also suitable for

Minka Aire F539-BCW User manual

Related papers

Other documents