EC Printer EC80320UE User manual

EC-80320 User’s Manual

- i -

The Guide

Be sure to have read the manual seriously before your operation. Neither EC PRINTER nor

its affiliates shall be liable to the purchaser of this product or third parties for damages,

losses, costs, or expenses incurred by purchaser or third parties as a result of: accident,

misuse, or abuse of this product or unauthorized modifications, repairs, or alterations to

this product, or failure to strictly comply with EC PRINTER’s operating and maintenance

instructions.

 Follow the notices and warnings carefully to avoid seriously bodily injury.

 Don’t touch the thermal head with your hand and other solid object at any moment to

avoid your body burned or the thermal head damaged.

 Be careful the dentate cutter when you replace the paper.

 You are forbidden to clean the printer with alcohol or other liquid when the printer is

connected to the power, pull the plug out when which is processed, using the soft cloth

instead of the hard object.

 Please don’t use the printer near the liquid.

 Make sure that the printer is connected to a reliable power outlet. It should not be on the

same electric circuit as copiers, refrigerators, or other appliances that cause power

spikes.

 Make sure the printer is far away from the appliance that can arouse electromagnetic jam,

such as loudhailer.

 The power outlet you plan to connect to should be nearby and unobstructed.

 Make sure that the surrounding area is clean, dry, free of dust and not exposed to direct

sunlight.

 Don’t remove the printer’s out-cover and repair the printer。When needed, call or take it

to the professional.

 Make sure to set the power switch OFF when connects the printer to the power or

computer.

 When the following error or problem occurred, please contact the professional or dealer:

A：The power cable is damaged or broken.

B：The printer is sloppy by some liquid.

C：The printer didn’t work when you operate according the manual.

D：The printer out-cover is broken.

E：The specification or print quality is going wrong obviously, need repaired.

Warning: In order to ensure the use life of printer, strictly prohibit printing full line full

black exceed than 2 CM.

Notice: The contents of this manual are subject to change without notice.

*All the part of the printer can be recycled. When it is abandoned, we can callback it

freely. Please contact us when you abandon it.

EC-80320 User’s Manual

- ii -

Table of contents

The Guide.................................................................................................................................................i

Chapter 1 Introduction...........................................................................................................................1

1.1 Features..........................................................................................................................................1

1.2 Part Description ..............................................................................................................................1

1.3 Parts Identification ..........................................................................................................................1

Chapter 2 Connecting Cables ...............................................................................................................3

2.1 Unpacking.......................................................................................................................................3

2.2 Unpack the Protect Materials..........................................................................................................3

2.3 Connecting to Your Computer or Other Equipment.........................................................................3

2.3.1 Connecting the Parallel Interface Cable...................................................................................3

2.3.2 Connecting the Serial Interface Cable (Optional).....................................................................4

2.3.3 Connecting the USB Interface Cable........................................................................................4

2.3.4 Connecting the Drawer Cable ..................................................................................................5

2.3.5 Connecting the Ethernet Cable ................................................................................................5

2.4 Connecting the Adapter ..................................................................................................................6

2.5 Setup the Print Driver and Select the Cutter ...................................................................................6

2.6 Network Settings.............................................................................................................................9

2.6.1 Connecting Printer....................................................................................................................9

2.6.2 Setting IP Address....................................................................................................................9

2.6.3 Installing Printer Network Driver.............................................................................................12

Chapter 3 Base Control Panel Operations.........................................................................................19

3.1 Control Panel ................................................................................................................................19

3.1.1 Indicator .................................................................................................................................19

3.1.2 KEY......................................................................................................................

..................19

3.2 Self-Printing ..................................................................................................................................19

3.3 HEX DUMP PRINTING.................................................................................................................20

3.4 Restoring Factory Printer Settings ................................................................................................20

3.5 Setting Slip Stitch..........................................................................................................................20

3.6 Online-aptitude Parameter Settings..............................................................................................20

Chapter 4 Install and Replace the Roll Paper.....................................................................................22

4.1 Paper Installed Steps ....................................................................................................................22

Chapter 5 Features...............................................................................................................................24

5.1 General Specification....................................................................................................................24

5.2 Interface Features.........................................................................................................................25

5.2.1 Parallel Interface ....................................................................................................................25

5.2.2 Serial Interface (Optional) ......................................................................................................26

5.2.3 USB Interface.........................................................................................................................27

5.2.4 Drawer Connector..................................................................................................................27

5.2.5 Power Supply Connector........................................................................................................28

5.2.6 Ethernet Connector................................................................................................................28

Chapter6 Troubleshooting and Maintenance.....................................................................................29

6.1 Maintenance .................................................................................................................................29

6.2 Error Message on the Control Panel.............................................................................................29

6.3 Cutter Jammed or Error ................................................................................................................29

Chapter 7 Control Commands.............................................................................................................31

7.1 General .........................................................................................................................................31

7.2. Explanation of Terms ...................................................................................................................31

Appendix Commands List...................................................................................................................44

EC-80320 User’s Manual

- 1 -

Chapter 1 Introduction

1.1 Features

EC80320 printer is a kind of high-speed mini thermal printer. It is a high-quality, high-reliability

and low-noise POS printer and operated easily, which can be widely used in ECR, PC-POS and

BANK POS for printing variety of receipt.

1.2 Part Description

According different data port (interface), EC80320 serials are divided into several different names:

EC80320 is the printer equipped with parallel interface, EC80320US is equipped with serial

interface and USB interface, EC80320U is equipped with USB interface and EC80320UE with

Ethernet interface and USB interface.

EC80320 serials printer is equipped with auto cutter, It have two kinds of cutter for the consumer

to selected: partial cutter can only cut the paper with one point left while full cutter cuts the paper

fully.

Note: Please contact with the dealer for changing the interface if needed.

1.3 Parts Identification

Parallel interface USB interface

USB + Serial

interface

USB + Ethernet

interface.

MODEL

EC80320 EC80320U EC80320US EC80320UE

Cover Open Lever

Power Switch

Power Indicator (Green)

Error Indicator (Red)

Paper out Indicator (Red)

FEED Key

Paper out Tunnel

(

Dentate

)

Manual Cutte

r

Small Cover

Fig1-1 Main part of the printer

EC-80320 User’s Manual

- 2 -

Parallel (or serial or USB) Interface position

Drawer connector Power connector

Fig1-2 Back of the printer

EC-80320 User’s Manual

- 3 -

Chapter 2 Connecting Cables

2.1 Unpacking

Check each item against the following packing list. If any of these items are missing. Please

contact your dealer.

The interface cable is optional, which will be equipped or cancelled according the customer’s

request.

2.2 Unpack the Protect Materials

1. Open the packing box, lift up the printer.

2. Save all the original packing materials, so that it can be used when to transport the printer.

2.3 Connecting to Your Computer or Other Equipment

Note：Before connecting/disconnecting the interface cable, make sure that power to the

printer and all the devices connected to the printer are turned off. Also make sure

the power cable plug is disconnected from the AC outlet.

2.3.1 Connecting the Parallel Interface Cable

1. Make sure the Host and the printer are both turned off, connect the parallel interface cable to

the connector on the rear panel of the printer, fasten the connector clasps as shown in Fig 2-2.

Fig2-1 Packing List

Printer

A

C Adapte

r

Power Cord

Facility user’s guide

Driver CD

(Includes Windows Driver and User’s manual)

Interface Cable

Pack List Guarantee Repair Card

EC-80320 User’s Manual

- 4 -

2. Connect the other end of the cable to the host. Tighten the connector screws.

3. This printer can carry out a network printing through connecting parallel interface to network

print server, which you can use are PS-1206, SX-110 and SX-3100 which have been

validated.

2.3.2 Connecting the Serial Interface Cable (Optional)

1. Make sure the Host and the printer are both turned off, connect the serial interface cable to the

connector on the rear panel of the printer. Tighten the connector screws as shown in Fig 2-3.

2. Connect the other end of the cable to the host’s serial connector and tighten the connector

screws.

2.3.3 Connecting the USB Interface Cable

1. Plug the USB cable A end (square shape) into the printer's USB connector as shown in Fig2-4.

2. Plug the other end of the USB cable (flat) to the computer’s USB connector.。

Fig2-3 Connecting the serial interface cable

Fig 2-2 Connecting the parallel interface cable

Serial Interface

Serial Cable

Screws

Parallel Interface Parallel Cable

Clip Wires

EC-80320 User’s Manual

- 5 -

2.3.4 Connecting the Drawer Cable

Turn off the printer and plug the drawer cable into the drawer connector on the back of the printer

as shown in Fig2-5.

Warning: Don’t connect a telephone line to the drawer connector; otherwise both the

telephone line and the printer may be damaged.

2.3.5 Connecting the Ethernet Cable

1. Plug the crystal end of the Ethernet cable (RJ-45) into the printer's Ethernet connector as

shown in Fig2-6.

2. Plug the other end of the Ethernet cable (flat) to the LAN’s entrance。

Fig2-5 Connecting the Drawer cable

Fig2-4 Connecting the USB interface cable

USB Interface

USB Cable

Drawer cable

Drawer connector

EC-80320 User’s Manual

- 6 -

2.4 Connecting the Adapter

1. Make sure the printer’s power switch is turned off. Plug the adapter’s supply cable as shown

below. Connect the adapter to the power cord.

2. Make sure the voltage of the electrical outlet matches that of the adapter.

3. Plug the adapter to the printer’s electrical outlet.

4. Plug the power thread one end to the adapter and the other to the AC outlet with ground wire.

Note: 1. If the voltage of electric outlet isn’t within the scope marked in the label, please

contact your dealer for solution, and must not connect the power cord to the

wall outlet.

2. Please use the exactitude electrical outlet with ground wire.

3. Make sure to use EC PRINTER original adapter, or we will not assume to take

ability for the printer damage.

2.5 Setup the Print Driver and Select the Cutter

You must setup the printer driver in Windows before using the EC80320 printer.

Please use the cable to connect computer with printer, then turn on the computer and the printer,

put the drive CD into the CD-ROM. Install driver by the following way:

Fig2-7 connecting the adapter

Ethernet cable

Ethernet connector

Fig2-6 Connecting the Ethernet cable

Power connector

Adapter

Power cord

EC-80320 User’s Manual

- 7 -

Auto-install way

Double click the file “Setup.exe” in the driver disc, install driver by the following direct.

Hand operated installing way

1) The installing steps for Windows 2000/XP are as follows:

1. Click “Start” -->"Settings", select “Printers”.

2. Click “Add Printer”, then it will show a window of “Add Printer Wizard”, click “Next”, then please

read the select direct carefully, Such as, select “Local printer” in the "Local or Network Printer"

window, then click “next”.

3. Come out a window of “Select the Printer Port”, select a usable port. Such as, select “LPT1:

printer port”, click “Next”.

4. Come out a window of “Manufacturers/Printers", click "Have Disk...", click “Next”.

5. Come out a window of “Install From Disk”. Please according to the operating system

environment, such as Windows XP operating system you should select the path as follow:

CD-ROM-“Driver”-“WIN2000(XP-Vista)”, which you can find a file named: EC80320.inf, click

“Open”, then click “OK” to return to the window of “"Manufacturers/Printers" , click “Next”.

6. Follow the direct click “Next” gradually till the installation is finished.

2) The installing steps for Windows 7 are as follows:

1. Click “Start” -->"Settings and Printers”.

2. Click “Add Printer”, then it will show a window of “Add Printer Wizard”, click “Next”, then please

read the select direct carefully, Such as, select “Local printer” in the "Local or Network Printer"

window, then click “next”.

3. Come out a window of “Select the Printer Port”, select a usable port. Such as, select “LPT1:

printer port”, click “Next”.

4. Come out a window of "Manufacturers/Printers", click "Have Disk...", click “Next”.

5. Come out a window of “Install From Disk”. Please according to the operating system

environment, such as Windows XP operating system you should select the path as follow:

CD-ROM-“Driver”-“WIN2000(XP-Vista)”, where you can find a file named: EC80320.inf, click

“Open”, then click “OK” to return to the window of "Manufacturers/Printers" , click “Next”.

6. Follow the direct click “Next” gradually till the installation is finished.

Please setup the driver following the setup description in the CD going along with the printer.

What’s more, you can use the TM-T88II, TM-T88III serials driver from EPSON.

If you want to cut the paper after printing, please select the “Full cut” or “Partial cut” in the

Paper/Quality page after clicking the “Printing Preferences” button, which lies in the “General”

page of the driver properties. Referring figure is shown below.

It is noted that if paper cut effect is the same whichever you select “full cut” or “partial cut” in the

driver properties, which means that the cutter (the printer equipped with) can only carry out one

kind of cut-method.

EC-80320 User’s Manual

- 8 -

The following condition may cause the printer can’t cut paper properly in Win2000/XP (or updated

version).

1. You do not setup the driver with the document setup.exe in the CD. Instead, you follow the

Windows’ installation guide.

2. Once you connect a printer with a parallel or serial port, but online with USB port Later, which

may cause a WINDOWS setup duplicate driver.

Only when the driver property is modified manually after being installed during the condition

mentioned above, does the cut- method take effect.

If you find the driver couldn’t cut paper, modify the driver property as shown below.

（1）cancel the “√” in the pane before the “Enable advanced printing features” in the “advanced”

page.

（2）Then click the “Print Processor” button as shown below. Enter the “Print Processor” dialogue

box, select the “JMProces” and “RAW”, and click the “OK” button.

Fig2-8 EC80320 Printing Preferences

EC-80320 User’s Manual

- 9 -

2.6 Network Settings

Please use EC PRINTER network setting software NetFinder to set the IP address for EC

PRINTER printers, which can be found in the CD or downloaded from EC products web site.

2.6.1 Connecting Printer

Power on the printer, connect with the Ethernet cable which has been connected to LAN, and look

into the information of Ethernet LED indicator to ensure the printer has entered into the normal

connection.

2.6.2 Setting IP Address

1. Run NetFinder Software

Double click NetFinder.exe in the PC which connects the printer in the same LAN. The figure

of the software is shown as follows:

Yellow LED Green LED Description

ON Flash Normal

OFF OFF Not connect to network

Fig2-9 Modify the driver property

EC-80320 User’s Manual

- 10 -

Button description:

Exit—Exit from the software

Search—Search printers in the same LAN

Assign IP—Modify the IP address and other settings for the specified printer.

2. Search printer

Click “Search” button in the main interface, the dialog box appearing will begin searching

automatically and show appearance, listing a printer in the main interface if found. The time is

counting down in the progress bar (10s in total) and the search will finish as soon as the time is

over. When going on searching, press “search” button again.

Fig2-10 Run NetFinder Software

Fig2-11 Search printer

EC-80320 User’s Manual

- 11 -

If the printer still can not be found out when the network connection is correct in the same

network, Please check whether the network fire wall on the PC open or not. If there is fire wall,

please close it temporarily, open again after finishing searching and setting a printer completely.

3. Setting printer’s IP address

The printer’s information is listed in the main interface, the left side of which is the model and

description and the right is the IP and MAC address. What’s more, the assign mode

(dynamic/static) is noted behind the IP address.

1) Correlative description for IP address settings

In order to search and set printer’s IP address conveniently for the first time, the factory default

setting is DHCP mode which assigns IP address dynamically. If there is no DHCP server in the

connected LAN and printer is set to DHCP mode as well, then it will use the internal pre-set

address (IP: 10.0.0.1, Subnet Mask: 255.255.255.0) automatically.

It is suggested that printer’s IP set to static in actual usage, which can cut down the time when

initializing the Ethernet interface as the printer is turned on and prevent IP conflicts (The

dynamic address used in printer may conflict with another one). The network segment part of

the IP address and Subnet Mask must be the same as those of PC connecting with a printer.

For example, the address of working PC is 192.168.0.1/255.255.255.0 (IP/Subnet Mask),then

which of printer should be set to 192.168.0.x/255.255.255.0（x=2~254 and should avoid the IP

in used. It is not restricted for NetFinder to search printers in the same network but different

segment parts (can not stride gateway). Relative glossary of IP address may refer to

corresponding information.

2) Setting printer’s IP address

Select the printer information to be modified (black frame appears), click “Assign IP” button. Set

the IP in the dialog box appearing.

Check the “Use DHCP” if need to assign dynamic address, the settings above will be disabled

Fig2-12 Setting printer’s IP address

EC-80320 User’s Manual

- 12 -

automatically. Please make sure there is a DHCP server in the network, or the printer can not

receive an effective IP address.

When to specify static address, uncheck “Use DHCP” and fill in “IP address”, “Subnet Mask”

and “Default Gateway”. If there is no gateway in the network, fill 255.255.255.255 in the “Default

gateway”. “IP address” and “Subnet Mask” should obey the assigning rules of local LAN

(Ethernet), please enquire the administrator of networks which the printer connects to for more

details.

Click “OK” to send address setting information to the specified printer. The printer takes

response after “Close this window on success” is checked, and then this dialog is closed

automatically. Select “Reload Timer” then the software will wait for the printer’s response.

Generally, printer will take response in a circle time if network connection is correct.

Click “Cancel” if you abandon the modification.

Click “Search” in the main interface again to update printer information after modifying the

printer’s IP address.

3) Report printer’s IP address

Report the printer’s IP address, which will be used in the section “Newly-install printer network

driver” or “Upgrade-install printer network driver (setting driver’s network port)”.

2.6.3 Installing Printer Network Driver

The ways of installing network driver are divided into Newly-install way and Upgrade-install way

according to whether the PC installs the printer driver or not.

If the printer driver hasn’t been installed on the PC, adopt newly-install way whose steps are

shown in “Newly-install printer network driver”.

If the printer driver has been installed on the PC, adopt Upgrade-install way whose steps are

shown in “Upgrade-install printer network driver”.

1. Newly-install printer network driver

1) Click “Start”Æ”Settings”, select “Printers.

2) Click “Add printer”, then come out a window of “Add Printer Wizard”, click “next”, then please

read the select direct carefully. Such as, select “local or Network Printer”, then click “next”.

3) Come out a window of “Select the Printer port”, select a port you want your printer to use. For

example, select “Create a new port”, select “Standard TCP/IP Port” in the port, click “next”.

4) Come out a window of “Add standard TCP/IP Printer Port Wizard”, click “Next”.

EC-80320 User’s Manual

- 13 -

5) Come out a window of “Add Port”, enter the IP address reported by the “Setting printer’s IP

address” in the “Printer Name or IP Address” column. Take IP address “192.168.0.240” for

example. “Port Name” is created automatically after finishing filling in IP address.

6) Come out a window of “Additional Port Information Required”, select “Custom” in the “Device

Type”, then click “Settings”.

7) Come out a window of “Port Settings”. Affirm that “Port name” and “Printer name or IP address”

are correct, “Protocol” is “RAW” and “Port Number” is “9100”, click “”OK”.

EC-80320 User’s Manual

- 14 -

8) Return to “Additional Port Information Required”, click “Next”.

9) Come out a window of “Completing the Add Standard TCP/IP Printer Port Wizard”, click

“Finish”.

10) In the selection of "Manufacturers/Printers", click “Have Disk”, and then click “Next”.

11) Come out a window of “Install From Disk”. Please according to the operating system

environment, such as Windows XP operating system you should select the path as follows:

CD-ROM-“Driver”-“WIN200(XP-Vista)”, that you can find a file named: EC80320.inf, click

“open”, then click “OK”, then return to the window “install printer software”, click “next”.

12) Follow the direct click “next” gradually till the installation is finish. At this time, printer network

driver is installed completely.

2. Upgrade-install printer network driver (setting driver’s network port)

If PC has installed the printer’s driver, set driver’s network port to carry out network printing.

The concrete steps are shown below:

1) Click “Start”Æ”Settings”, select “Printers”

2) Right click EC80320 driver, click “Properties” on the window coming out.

3) Come out a window of “Properties”, click “Ports” and “Add Ports”.

EC-80320 User’s Manual

- 15 -

4) Come out a window of “Printer port”, select “Standard TCP/IP Port”, click “New port”.

5) Come out a window of “Add Standard TCP/IP Printer Port Wizard”, click “Next”.

6) Come out a window of “Add a port”, import the IP address reported by the “Setting printer’s

IP address” in the “Printer name or IP address” column. Take IP address “192.168.0.240” for

example. “Port name” is created automatically after finishing filling in IP address. Click

“Next”.

EC-80320 User’s Manual

- 16 -

7) Come out a window of “Port information”, select “User-defined” in the “Equipment style”,

then click “setting”. Come out a window of “Additional Port Information Required”, select

“Custom” in the “Device Type”, then click “settings”.

8) Come out a window of “Port Settings”. Affirm that “Port name” and “Printer name or IP

address” are correct, “Protocol” is “RAW” and “Port Number” is “9100”, click “”OK”.

EC-80320 User’s Manual

- 17 -

9) Return to “Additional Port Information Required”, click “Next”.

10) Come out a window of “Completing the Add Standard TCP/IP Printer Port Wizard”, click

“Finish”.

11) Return to “Printer Ports”, click “Close

EC-80320 User’s Manual

- 18 -

12) Return to “Properties”, make sure the network port is selected, click “Apply”, and then click

“Close”. Thus, printer’s network port setting is finished.

Page is loading ...

EC Printer EC80320UE User manual

This manual is also suitable for

EC Printer EC80320UE User manual

Other documents