STIEBEL ELTRON 235907 Operation and Installation

BEDIENUNG UND INSTALLATION

OPERATION AND INSTALLATION

UTILISATION ET INSTALLATION

BEDIENING EN INSTALLATIE

USO E INSTALLAZIONE

OBSLUHA A INSTALACE

OBSŁUGA I INSTALACJA

KÄYTTÖ JA ASENNUS

KEZELÉS ÉS TELEPÍTÉS

Warmwasser-Standspeicher | Floorstanding DH W cylinder | Ballon ECS sur pied |

Staande warmwaterboiler | Acqua calda - Caldaia verticale | Stacionární zásobník

teplé vody | Stojący zasobnik c.w.u. | Lattiamallinen käyttövesivaraaja | Álló melegvíztároló

» SBB 600 WP SOL

» SBB 800 WP SOL

» SBB 1000 WP SOL

Page is loading ...

14 | SBB 600-1000 WP SOL WWW.STIEBEL-ELTRON.COM

CONTENTS | OPERATION

GENERAL INFORMATION

OPERATION

1. General information �� 14

1.1 Safety instructions ��14

1.2 Other symbols in this documentation �� 15

1.3 Units of measurement ��15

2. Safety �� 15

2.1 Intended use ��15

2.2 General safety instructions �� 15

3. Appliance description �� 15

4. Cleaning, care and maintenance �� 16

5. Troubleshooting �� 16

INSTALLATION

6. Safety �� 16

6.1 General safety instructions �� 16

6.2 Regulations, standards and instructions �� 16

7. Appliance description �� 16

7.1 Standard delivery �� 16

7.2 Accessories �� 16

8. Preparations �� 17

8.1 Installation site �� 17

8.2 Transport �� 17

9. Installation �� 17

9.1 Heating or solar installation ��18

9.2 Water connection and safety assembly �� 18

10. Commissioning �� 19

10.1 Initial commissioning �� 19

10.2 Recommissioning �� 19

11. Shutting down �� 19

12. Troubleshooting �� 19

13. Maintenance �� 19

13.1 Checking the safety valve �� 19

13.2 Draining the appliance �� 19

13.3 Replacing the signal anode �� 19

13.4 Cleaning and descaling the appliance �� 19

14. Speciﬁcation �� 20

14.1 Dimensions and connections �� 20

14.2 Fault conditions ��23

14.3 Data table �� 23

GUARANTEE

ENVIRONMENT AND RECYCLING

OPERATION

1. General information

The chapter "Operation" is intended for appliance users and heat-

ing contractors.

The chapter "Installation" is intended for heating contractors.

Note

Read these instructions carefully before using the appli-

ance and retain them for future reference.

Pass on the instructions to a new user if required.

1.1 Safety instructions

1.1.1 Structure of safety instructions

!

KEYWORD Type of risk

Listed here are the possible consequences that may re-

sult from failure to observe the safety instructions.

 Steps to prevent the risk are listed.

1.1.2 Symbols, type of risk

Symbol Type of risk

Injury

Electrocution

Burns

(burns, scalding)

1.1.3 Keywords

KEYWORD Meaning

DANGER Failure to observe this information will result in serious

injury or death.

WARNING Failure to observe this information may result in serious

injury or death.

CAUTION Failure to observe this information may result in moderate

or minor injury.

!

OPERATION

SAFETY

ENGLISH

WWW.STIEBEL-ELTRON.COM SBB 600-1000 WP SOL | 15

1.2 Other symbols in this documentation

Note

General information is identiﬁed by the symbol shown

on the left.

 Read these texts carefully.

Symbol Meaning

Material losses

(appliance, consequential, environment)

Appliance disposal

 This symbol indicates that you have to do something. The ac-

tion you need to take is described step by step.

1.3 Units of measurement

Note

All measurements are given in mm unless stated oth-

erwise.

2. Safety

2.1 Intended use

The appliance is intended for heating and storing domestic hot

water when operating a heat pump with a higher or a high out-

put. May be combined with heat provided by solar collectors.

Both indirect coils can be linked in series for the highest possible

transfer rate.

Suitable ﬂanged and threaded immersion heaters can be ﬁtted

by contractors.

Any other use beyond that described shall be deemed inappropri-

ate. Observation of these instructions and of instructions for any

accessories used is also part of the correct use of this appliance.

2.2 General safety instructions

WARNING Burns

There is a risk of scalding at outlet temperatures in ex-

cess of 43°C.

!

WARNING Injury

Where children or persons with limited physical, sensory

or mental abilities are allowed to operate this appliance,

ensure that this will only happen under supervision or

after appropriate instruction by a person responsible

for their safety.

Children should be supervised to ensure that they never

play with the appliance!

Note

The appliance is under pressure.

During the heat-up process, expansion water will drip

from the safety valve. If water continues to drip when

the heat-up process is completed, please inform your

qualiﬁed contractor.

3. Appliance description

The thermal energy in the heating water from the heat pump or

the solar collectors is transferred to the domestic hot water by two

twin pipe indirect coils.

The internal steel cylinder is coated in special directly applied

"anticor

®

" enamel and is equipped with a thermometer and a

signal anode. The anode with consumption indicator protects the

internal cylinder from corrosion.

!

16 | SBB 600-1000 WP SOL WWW.STIEBEL-ELTRON.COM

OPERATION | INSTALLATION

CLEANING, CARE AND MAINTENANCE

4. Cleaning, care and maintenance

 Have a contractor regularly check the appliance, the safety

assembly and all ﬁtted accessories.

 Never use abrasive or corrosive cleaning agents. A damp

cloth is sufﬁcient for cleaning all plastic parts.

Signal anode consumption indicator

!

Material losses

If the consumption indicator changes colour from white to

red, have the signal anode checked by a heating contrac-

tor and if necessary replaced.

1

2

26�03�01�1345

Signal anode consumption indicator

1 white = anode OK

2 red = check by heating contractor required

Scaling

 Almost every type of water deposits limescale at high tem-

peratures. This settles inside the appliance and affects both

the performance and service life. The indirect coils and ﬁtted

accessories should therefore be descaled from time to time.

A heating contractor who knows the local water quality will

tell you when the next service is due.

 Check the taps/valves regularly. You can remove limescale

deposits at the tap outlets using commercially available des-

caling agents.

5. Troubleshooting

Telephone your contractor.

To facilitate and speed up your enquiry, please provide the serial

number from the type plate (000000-0000-000000):

Made in Germany

000000-0000-000000

D0000078748

INSTALLATION

6. Safety

Only a qualiﬁed contractor should carry out installation, commis-

sioning, maintenance and repair of the appliance.

6.1 General safety instructions

We can only guarantee trouble-free function and operational reli-

ability if original spare parts intended for the appliance are used.

6.2 Regulations, standards and instructions

Note

Observe all applicable national and regional regulations

and instructions.

7. Appliance description

7.1 Standard delivery

Delivered with the appliance:

- Signal anode

- Heat conducting paste

- Thermometer

- Additional type plate

- Label "Signal anode information"

7.2 Accessories

7.2.1 Required accessories

Depending on the static pressure, safety assemblies and pressure

reducing valves are available. These type-tested safety assemblies

protect the appliance against inadmissible excess pressure.

7.2.2 Further accessories

In addition, ﬂanged as well as threaded immersion heaters and

thermal insulation are available as accessories.

If it is not possible to insert a rod anode from above, install a

segmented anode.

ENGLISH

WWW.STIEBEL-ELTRON.COM SBB 600-1000 WP SOL | 17

INSTALLATION

PREPARATIONS

8. Preparations

8.1 Installation site

 Always install the appliance in a room free from the risk of

frost and near the draw-off point.

 Ensure the ﬂoor has sufﬁcient load bearing capacity and

evenness (see chapter "Speciﬁcation / Data table").

 Observe the room height and height when tilted (see chapter

"Speciﬁcation / Data table").

Minimum clearances

SBB 600 WP SOL:

≥400 ≥130

≥200≥200

≥800

D0000057342

SBB 800-1000 WP SOL:

≥400 ≥220

≥200≥200

≥800

D0000057343

 Maintain the minimum clearances.

8.2 Transport

For handling/lifting, use the lifting eyes provided, but never the

"Optional DHW outlet" connection at the top of the appliance.

9. Installation

9.2.1 Fitting the thermal insulation, if appropriate.

 Position the appliance in its intended site.

 Fit the thermal insulation according to the instructions sup-

plied. For this, ensure that there is enough space for the

installation task. You can then link the appliance into the

heating and DHW system.

9.2.2 Fitting the signal anode

!

Material losses

When operating the cylinder without consumption indica-

tor, leave the plug in the ﬁtting.

26�02�09�0031

 Pull the plug out by simultaneously pushing the pressure

ring down.

 Push the open pipe end of the consumption indicator into the

aperture for the anode.

9.2.3 Fitting the thermometer and temperature sensor

 Insert the thermometer as far as it will go and align it.

 Insert the temperature sensor as far as it will go into the

sensor well for the HP return sensor. Apply heat conducting

paste.

9.2.4 Where appropriate, ﬁt the ﬂanged or threaded

immersion heater.

 Remove the dummy ﬂanges and plugs in order to mount the

ﬂanged or threaded immersion heater. Maintain the DC sepa-

ration towards the cylinder.

18 | SBB 600-1000 WP SOL WWW.STIEBEL-ELTRON.COM

INSTALLATION

9.1 Heating or solar installation

 Prior to connecting the heating water lines or the solar ther-

mal system, ﬂush the indirect coils with water.

 You may connect both indirect coils to the "heat pump return"

and "solar ﬂow" (see chapter "Speciﬁcation / Dimensions and

connections").

Connect the hydraulic connections with ﬂat gaskets.

 Fit the sensors for the control units used according to the

relevant installation instructions (for sensor well, see chapter

"Speciﬁcation / Dimensions and connections").

 Route the connecting lead to the solar or heating circuit con-

trol unit.

9.1.1 Water quality, solar circuit

A glycol/water mixture of up to 60% is permitted for the indirect

coil in the solar circuit if only dezinciﬁcation-resistant metals,

glycol-resistant gaskets and diaphragm expansion vessels suitable

for glycol are used throughout the installation.

9.1.2 Oxygen diffusion

!

Material losses

Avoid open heating systems and plastic pipes in under-

ﬂoor heating systems which are permeable to oxygen.

In underﬂoor heating systems with plastic pipes that are per-

meable to oxygen and in open vented heating systems, oxygen

diffusion may lead to corrosion on the steel components of the

heating system (e.g. on the indirect coil of the DHW cylinder, on

buffer cylinders, steel heating elements or steel pipes).

!

Material losses

The products of corrosion (e.g. rusty sludge) can settle in

the heating system components and can result in a lower

output or fault shutdowns due to reduced cross-sections.

!

Material losses

Avoid open vented solar thermal systems and plastic

pipes which are permeable to oxygen.

With plastic pipes that are permeable to oxygen, oxygen diffusion

may lead to corrosion on the steel components of the solar thermal

system (e.g. on the indirect coil of the DHW cylinder).

9.2 Water connection and safety assembly

9.2.1 Safety instructions

Note

Carry out all water connection and installation work in

accordance with regulations.

!

Material losses

If a ﬂanged immersion heater is ﬁtted and plastic pipe-

work is used at the same time, observe chapter "Speciﬁ-

cation/ Fault conditions".

!

Material losses

Operate the appliance only with pressure-tested taps and

valves.

Cold water line

Galvanised steel, stainless steel, copper and plastic pipework are

approved materials.

!

Material losses

A safety valve is required.

DHW line

Stainless steel, copper and plastic pipework are approved ma-

terials.

9.2.2 Water connection

 Flush the line thoroughly.

 Install the DHW and the cold water lines with the safety as-

sembly. Bear in mind that, depending on the static pressure,

you may also need a pressure reducing valve.

Connect the hydraulic connections with ﬂat gaskets.

 Size the drain so that water can drain off unimpeded when

the safety valve is fully opened. The blow-off aperture of the

safety valve must remain open to the atmosphere.

 Fit the blow-off line of the safety assembly with a constant

fall.

ENGLISH

WWW.STIEBEL-ELTRON.COM SBB 600-1000 WP SOL | 19

INSTALLATION

COMMISSIONING

10. Commissioning

10.1 Initial commissioning

 Open a draw-off point until the appliance has ﬁlled up and

the pipework is free of air.

 Adjust the ﬂow rate. For this, observe the maximum permis-

sible ﬂow rate with a fully opened tap (see chapter "Speciﬁ-

cation / Data table"). If necessary reduce the ﬂow rate at the

butterﬂy valve of the safety assembly.

 Carry out a tightness check.

 Vent the internal indirect coils.

 Switch the mains power ON if required.

 Check the function of the safety assembly.

 Check the function of ﬁtted accessories.

 Then check the function of the solar thermal system, if

appropriate.

 If relevant, check that the DHW temperature displayed on the

heat pump control unit is correct.

10.1.1 Appliance handover

 Explain the function of the appliance to users and familiarise

them with its operation.

 Make users aware of potential dangers, especially the risk of

scalding.

 Hand over these instructions.

10.2 Recommissioning

See chapter "Initial commissioning".

11. Shutting down

 If necessary, disconnect any accessories installed from the

mains at the MCB/fuse in the fuse box.

 Drain the appliance. See chapter "Maintenance / Draining the

appliance".

12. Troubleshooting

Fault Cause Remedy

The safety valve drips

when the heating is

switched off.

The valve seat is con-

taminated.

Clean the valve seat.

13. Maintenance

WARNING Electrocution

Carry out all electrical connection and installation work

in accordance with relevant regulations.

WARNING Electrocution

Before any work on the appliance, disconnect all poles

of the appliance from the power supply.

If you need to drain the appliance, observe chapter "Draining the

appliance".

13.1 Checking the safety valve

 Regularly vent the safety valve on the safety assembly until a

full water jet is discharged.

13.2 Draining the appliance

WARNING Burns

Hot water may escape during the draining process.

If the appliance needs to be drained for maintenance or to protect

the whole installation when there is a risk of frost, proceed as

follows:

 Close the shut-off valve in the cold water inlet pipe.

 Open the hot water taps on all draw-off points.

 Drain the appliance via the "Cold water inlet" (see chapter

"Speciﬁcation / Dimensions and connections"). Please note

that residual water remains in the appliance.

13.3 Replacing the signal anode

 Replace the signal anode if it becomes depleted. For this, ob-

serve the maximum transition resistance between the anode

and the cylinder of 0.3Ω.

13.4 Cleaning and descaling the appliance

26�03�01�0847

1

1 Threaded extraction holes

 Use the threaded extraction holes to release the ﬂange plate

from the ﬂange connector.

For the torque of the ﬂange screws, see chapter "Speciﬁcation /

Dimensions and connections".

 Never use descaling pumps.

 Never treat the cylinder surface or the signal anode with des-

caling agents.

20 | SBB 600-1000 WP SOL WWW.STIEBEL-ELTRON.COM

INSTALLATION

SPECIFICATION

14. Speciﬁcation

14.1 Dimensions and connections

SBB 600 WP SOL

50°

750

970

285

385

505

725

875

1285

330

630

1093

1435

1775

1674

i18

h43

i01

c06

c01

c10

d01

d25

h06

h05

h28

d02

d26

i18

1093

i07

D0000020807

d01

h05

i07

d26

d02

h06

d25

h28

i18

h43

i01

c10

c01

D0000052943

SBB 600 WP

SOL

c01 Cold water inlet Male thread G 1 ¼ A

c06 DHW outlet Male thread G 1 ¼ A

c10 DHW circulation Male thread G ½ A

d01 Heat pump flow Female thread G 1 ½

d02 Heat pump return Female thread G 1 ½

d25 Solar flow Female thread G 1 ½

d26 Solar return Female thread G 1 ½

h05 Sensor heat pump DHW Diameter mm 9.5

h06 Sensor heat pump DHW

optional

Diameter mm 9.5

h28 Sensor solar cylinder Diameter mm 9.5

h43 Thermometer Diameter mm 14.5

i01 Flange

Diameter mm 280

Pitch circle diameter mm 245

Screws M 14

Torque Nm 80

i07 Electric emergency/

booster heater

Female thread G 1 ½

i18 Protective anode Female thread G 1 1/4

ENGLISH

WWW.STIEBEL-ELTRON.COM SBB 600-1000 WP SOL | 21

INSTALLATION

SPECIFICATION

SBB 800 WP SOL

285

385

560

780

930

1320

1440

1943

330

680

1200

1300

1560

1675

1919

2065

50°

i18

i03

i02

h43

c06

c01

c10

d01

d25

h06

h28

d02

d26

790

1010

1820

h05

D0000020808

SBB 800 WP SOL

c01 Cold water inlet Male thread G 2 A

c06 DHW outlet Male thread G 2 A

c10 DHW circulation Male thread G 1 A

d01 Heat pump flow Female thread G 1 ½

d02 Heat pump return Female thread G 1 ½

d25 Solar flow Female thread G 1 ½

d26 Solar return Female thread G 1 ½

h05 Sensor heat pump DHW Diameter mm 9.5

h06 Sensor heat pump DHW optional Diameter mm 9.5

h28 Sensor solar cylinder Diameter mm 9.5

h43 Thermometer Diameter mm 14.5

i02 Flange 1

Diameter mm 280

Pitch circle diameter mm 245

Screws M 14

Torque Nm 80

i03 Flange2

Diameter mm 280

Pitch circle diameter mm 245

Screws M 14

Torque Nm 80

i18 Protective anode Female thread G 1 1/4

22 | SBB 600-1000 WP SOL WWW.STIEBEL-ELTRON.COM

INSTALLATION

SPECIFICATION

SBB 1000 WP SOL

285

385

670

890

1040

1450

1550

2153

330

790

1365

1410

1670

1885

2129

2275

50°

i18

i02

h43

c06

c01

c10

d01

d25

h06

h28

d02

d26

790

1010

1820

h05

i03

D0000020811

SBB 1000 WP SOL

c01 Cold water inlet Male thread G 2 A

c06 DHW outlet Male thread G 2 A

c10 DHW circulation Male thread G 1 A

d01 Heat pump flow Female thread G 1 ½

d02 Heat pump return Female thread G 1 ½

d25 Solar flow Female thread G 1 ½

d26 Solar return Female thread G 1 ½

h05 Sensor heat pump DHW Diameter mm 9.5

h06 Sensor heat pump DHW optional Diameter mm 9.5

h28 Sensor solar cylinder Diameter mm 9.5

h43 Thermometer Diameter mm 14.5

i02 Flange 1

Diameter mm 280

Pitch circle diameter mm 245

Screws M 14

Torque Nm 80

i03 Flange2

Diameter mm 280

Pitch circle diameter mm 245

Screws M 14

Torque Nm 80

i18 Protective anode Female thread G 1 1/4

ENGLISH

WWW.STIEBEL-ELTRON.COM SBB 600-1000 WP SOL | 23

INSTALLATION

SPECIFICATION

Appliance cross-section SBB 800 WP SOL | SBB 1000 WP SOL

d01

h05

d26

i03

d02

h06

d25

h28

c10

i18

h43

i02

c01

c06

h06

D0000052946

14.2 Fault conditions

In the event of a fault, temperatures of up to 95°C at 1.0 MPa can

occur depending on the type of heat sources used.

14.3 Data table

SBB 600 WP SOL SBB 800 WP SOL SBB 1000 WP SOL

235906 235907 235908

Hydraulic data

Nominal capacity l 575 770 835

Capacity, upper indirect coil l 48 52 52

Capacity, lower indirect coil l 16 21 30

Surface area, upper indirect coil m² 5.7 6.2 6.2

Surface area, lower indirect coil m² 2.0 2.6 3.6

Pressure drop at 1.0 m³/h, upper indirect coil hPa 3.6 3.9 3.9

Pressure drop at 1.0 m³/h, lower indirect coil hPa 2.4 3.2 3.4

Application limits

Max. permissible pressure MPa 1 1 1

Test pressure MPa 1.5 1.5 1.5

Max. permissible temperature °C 95 95 95

Max. flow rate l/min 70 90 90

Max. recommended collector aperture area m² 12 14 17

Dimensions

Height mm 1775 1943 2153

Height incl. thermal insulation mm 1775 2065 2275

Diameter mm 750 790 790

Diameter incl. thermal insulation mm 970 1010 1010

Height when tilted mm 1813 1990 2185

Weights

Weight, empty kg 244 296 321

Weight, full kg 883 1139 1238

INSTALLATION | GUARANTEE | ENVIRONMENT AND RECYCLING

SPECIFICATION

Guarantee

The guarantee conditions of our German companies do not

apply to appliances acquired outside of Germany. In countries

where our subsidiaries sell our products a guarantee can only

be issued by those subsidiaries. Such guarantee is only grant-

ed if the subsidiary has issued its own terms of guarantee. No

other guarantee will be granted.

We shall not provide any guarantee for appliances acquired in

countries where we have no subsidiary to sell our products.

This will not aect warranties issued by any importers.

Environment and recycling

We would ask you to help protect the environment. After use,

dispose of the various materials in accordance with national

regulations.

GUARANTEE

ENVIRONMENT AND RECYCLING

Page is loading ...

MAGYAR

WWW.STIEBEL-ELTRON.COM SBB 600-1000 WP SOL | 95





Deutschland

STIEBEL ELTRON GmbH & Co. KG

Dr.-Stiebel-Straße 33 | 37603 Holzminden

Tel. 05531 702-0 | Fax 05531 702-480

[email protected]

www.stiebel-eltron.de

Verkauf Tel. 05531 702-110 | Fax 05531 702-95108 | info-[email protected]

Kundendienst Tel. 05531 702-111 | Fax 05531 702-95890 | [email protected]

Ersatzteilverkauf Tel. 05531 702-120 | Fax 05531 702-95335 | [email protected]

Irrtum und technische Änderungen vorbehalten! | Subject to errors and technical changes! | Sous réserve

d‘erreurs et de modifications techniques! | Onder voorbehoud van ver

g

issin

g

en en technische wi

j

zi

g

in

g

en! |

Salvo error o modificación técnica! | Excepto erro ou alteração técnica | Zastrzeżone zmian

y

techniczne i

ewentualne błędy | Omyly a technické změny jsou vyhrazeny! | A muszaki változtatások és tévedések

j

o

g

át

fenntartjuk! |

Отсутствие ошибок не гарантируется. Возможны технические изменения.

| Ch

y

b

y

a

technické zmeny sú vyhradené! Stand 9147

Australia

STIEBEL ELTRON Australia Pty. Ltd.

6 Prohasky Street | Port Melbourne VIC 3207

Tel. 03 9645-1833 | Fax 03 9645-4366

[email protected]

www.stiebel.com.au

Austria

STIEBEL ELTRON Ges.m.b.H.

Gewerbegebiet Neubau-Nord

Margaritenstraße 4 A | 4063 Hörsching

Tel. 07221 74600-0 | Fax 07221 74600-42

[email protected]

www.stiebel-eltron.at

Belgium

STIEBEL ELTRON bvba/sprl

't Hofveld 6 - D1 | 1702 Groot-Bijgaarden

Tel. 02 42322-22 | Fax 02 42322-12

[email protected]

www.stiebel-eltron.be

China

STIEBEL ELTRON (Guangzhou) Electric

Appliance Co., Ltd.

Rm 102, F1, Yingbin-Yihao Mansion, No. 1

Yingbin Road

Panyu District | 511431 Guangzhou

Tel. 020 39162209 | Fax 020 39162203

info@stiebeleltron.cn

www.stiebeleltron.cn

Czech Republic

STIEBEL ELTRON spol. s r.o.

K Hájům 946 | 155 00 Praha 5 - Stodůlky

Tel. 251116-111 | Fax 235512-122

[email protected]

www.stiebel-eltron.cz

Finland

STIEBEL ELTRON OY

Kapinakuja 1 | 04600 Mäntsälä

Tel. 020 720-9988

[email protected]

www.stiebel-eltron.fi

France

STIEBEL ELTRON SAS

7-9, rue des Selliers

B.P 85107 | 57073 Metz-Cédex 3

Tel. 0387 7438-88 | Fax 0387 7468-26

[email protected]

www.stiebel-eltron.fr

Hungary

STIEBEL ELTRON Kft.

Gyár u. 2 | 2040 Budaörs

Tel. 01 250-6055 | Fax 01 368-8097

[email protected]

www.stiebel-eltron.hu

Japan

NIHON STIEBEL Co. Ltd.

Kowa Kawasaki Nishiguchi Building 8F

66-2 Horikawa-Cho

Saiwai-Ku | 212-0013 Kawasaki

Tel. 044 540-3200 | Fax 044 540-3210

[email protected]

www.nihonstiebel.co.jp

Netherlands

STIEBEL ELTRON Nederland B.V.

Daviottenweg 36 | 5222 BH 's-Hertogenbosch

Tel. 073 623-0000 | Fax 073 623-1141

[email protected]

www.stiebel-eltron.nl

Poland

STIEBEL ELTRON Polska Sp. z O.O.

ul. Działkowa 2 | 02-234 Warszawa

Tel. 022 60920-30 | Fax 022 60920-29

[email protected]

www.stiebel-eltron.pl

Russia

STIEBEL ELTRON LLC RUSSIA

Urzhumskaya street 4,

building 2 | 129343 Moscow

Tel. 0495 7753889 | Fax 0495 7753887

[email protected]

www.stiebel-eltron.ru

Slovakia

TATRAMAT - ohrievače vody s.r.o.

Hlavná 1 | 058 01 Poprad

Tel. 052 7127-125 | Fax 052 7127-148

[email protected]

www.stiebel-eltron.sk

Switzerland

STIEBEL ELTRON AG

Industrie West

Gass 8 | 5242 Lupfig

Tel. 056 4640-500 | Fax 056 4640-501

[email protected]

www.stiebel-eltron.ch

Thailand

STIEBEL ELTRON Asia Ltd.

469 Moo 2 Tambol Klong-Jik

Amphur Bangpa-In | 13160 Ayutthaya

Tel. 035 220088 | Fax 035 221188

info@stiebeleltronasia.com

www.stiebeleltronasia.com

United Kingdom and Ireland

STIEBEL ELTRON UK Ltd.

Unit 12 Stadium Court

Stadium Road | CH62 3RP Bromborough

Tel. 0151 346-2300 | Fax 0151 334-2913

[email protected]

www.stiebel-eltron.co.uk

United States of America

STIEBEL ELTRON, Inc.

17 West Street | 01088 West Hatfield MA

Tel. 0413 247-3380 | Fax 0413 247-3369

[email protected]

www.stiebel-eltron-usa.com

A 321107-40607-9340

4<AMHCMO=cbbahf>

STIEBEL ELTRON 235907, SBB 1000 WP SOL, SBB 600 WP SOL, SBB 600_1000_WP_SOL Operation and Installation

Related papers

Other documents