Mounting Instructions
Öhlins front fork kit FG 310 for Yamaha R1
© Öhlins Racing AB. All rights reserved. Any reprinting or unauthorized use without the
written permission of Öhlins Racing AB is prohibited. Printed in Sweden.
Rebound damping
adjuster
Compression
damping adjuster
Öhlins front fork 43
Your Öhlins front fork 43 is an upside down type
front fork featuring the following adjusters.
Compression damping adjuster
Adjustments are made at the bottom of the front
fork leg. Use a 3 mm allen key.
Rebound damping adjuster
Adjustments are made at the top of the fork leg.
Use a 3 mm allen key.
Spring preload adjuster
Adjustments are made by turning the nut at the
top of the fork leg. Clockwise for harder adjust-
ment, counter clockwise too release the preload.
Use a 17 mm wrench.
NOTE!
When delivered the Öhlins front fork is dialed to
recommended settings for the specific brand and
make of the motorcycle. If you have changed the
setting check like this:
The adjusters have a normal right hand thread. Turn
the damping adjusters clockwise to fully closed (pos.
zero [0]). Turn counter clockwise to open and count
the clicks until you reach the recommended number
of clicks. See Setup data at page 8.
CAUTION!
Do not use to much force, delicate sealing
surfaces can be damaged.
Spring preload
adjuster
FG 310, issued 04 01 07
Öhlins Racing AB, Box 722, S-194 27 Upplands Väsby, Sweden.
Phone +46 8 590 025 00, fax +46 8 590 025 80.
E-mail: [email protected]
www.ohlins.com
Bike on a stand. Bike on the ground. Bike with rider on.
Checking sag and ride height
Front suspension
F1. Bike on a stand with the
suspension fully extended = ............
F2. Bike on the ground without rider = ............
F3. Bike on the ground with rider = ............
Free sag
F1 - F2 = ............
Ride height
F1 - F3 = ............
Rear suspension
R1.Bike on a stand with the
suspension fully extended = ............
R2.Bike on the ground without rider = ........... .
R3.Bike on the ground with rider = ............
Free sag
R1 - R2 = ............
Ride height
R1 - R3 = ............
NOTE!
If ride height is higher than recommended,
softer spring/springs must be used.
If ride height is lower than recommended,
harder spring/springs must be used.
Contact your Öhlins dealer for advice.
Setup data
Length 730 mm
Stroke 120 mm
Rebound adjustment 12 clicks
Compression adjustment 12 clicks
Preload 13 mm
Spring rate 9.5 N/mm
Oil level 170 mm
F1
R1
F2
R2
F3
R3
Before installation
Öhlins Racing AB can not be held responsible for
any damage whatsoever to front fork or vehicle,
or injury to persons, if the instructions for fitting
and maintenance are not followed exactly.
Similarly, the warranty will become null and void
if the instructions are not adhered to.
WARNING!
1. Installing a front fork, that is not approved
by the vehicle manufacturer, may affect the
stability of your vehicle. Öhlins Racing AB
cannot be held responsible for any personal
injury or damage whatsoever that may oc-
cur after fitting the front fork. Contact an
Öhlins dealer or other qualified person for
advice.
2. Please study and make certain that you
fully understand all the mounting instructions
and the owners manuals before handling this
front fork kit. If you have any questions re-
garding proper installation procedures, con-
tact an Öhlins dealer or other qualified per-
son.
3. The vehicle service manual must be referred
to when installing the Öhlins front fork
Safety signals
Important information concerning safety is
distinguished in this manual by the
following notations:
The Safety alert symbol means:
Caution! Your safety is involved.
WARNING!
Failure to follow warning instructions
could result in severe or fatal injury
to anyone working with, inspecting or
using the suspension, or to bystanders.
CAUTION!
Caution indicates that special pre-
cautions must be taken to avoid dam-
age to the suspension.
NOTE!
This indicates information that is of
importance with regard to procedures.
Öhlins products are subject to continual improve-
ment and development. Consequently, although
these instructions include the most up-to-date
information available at the time of printing, there
may be minor differences between your suspen-
sion and this manual. Please consult your Öhlins
dealer if you have any questions with regard to
the contents of the manual.
NOTE!
During storage and transportation, espe-
cially at high ambient temperature, the oil
and grease used for assembling may run out
inside the packing and damage the
expanded polystyrene packing material. This
is not unusual and is in no way detrimental
to the front fork.
Kit contents
Before installing the front fork, please check the
contents of the kit. If anything is missing, contact
your Öhlins dealer.
Description Pcs. Part No.
Front Fork 1 04790-01
Caliper bracket LH 1 01677-26
Caliper bracket RH 1 01677-27
Fender bracket front 2 01678-07
Fender bracket top 2 01682-01
Fender bracket, angle 2 01678-08
Bolt MF6S5x12 8 00382-08
Bolt M4x12 4 00382-04
Bolt M14 1 01680-11
Shaft sleeve 28/32 1 01679-05
Shaft sleeve 22/32 1 01679-06
Sticker Öhlins 2 00194-10
Owners Manual
Notes
WARNING!
1. It´s advisable to have an Öhlins dealer or
other qualified person to fit your suspension.
2. Instructions in the vehicle service
manual are to be followed when changing
the suspension.
3. When working on a lifted vehicle it must
be securely supported to prevent it from
falling.
Mounting instruction
1
Put the bike om a stand so the front wheel
has ground clearance. Make sure it’s stead-
ily positioned and will not fall over.
2
Release the brake caliper on each side and
let them hang by the brake hoses.
3
Remove the front wheel, by loosening and
pulling the shaft out.
4
Remove the front fender.
5
Release the attachments of the front fork
legs in the lower and the upper triple clamps.
6
Pull the fork legs out downwards and re-
move them from the motorcycle.
NOTE!
When performing operations 7 – 10, do not
tighten the bolts and screws..
7
Fit the shaft sleeves to the fork bottom of
the Öhlins front forks.
8
7
8
Fit the brake caliper brackets with bolts
supplied.
Notes
9
Fit the two small fender brackets to the
caliper brackets with bolts supplied.
10
11
Fit the Öhlins front fork legs to the triple
clamps. Do not tighten until the legs are in
correct position, see Note! below.
10
Assemble the angle fender bracket and the
front fender brackets. Fit the assembly to
the fork leg bottom.
11
The top of the front fork
tube (not top nut) must be
aligned with the surface
of the triple clamp.
9
NOTE!
The fork legs are to be mounted so that the
top of the front fork tube is aligned in height
with the top edge of the triple clamp.
12
Tighten first the upper triple clamp than the
lower one to correct torque. See the motor-
cycle’s Workshop manual.
CAUTION!
Do not overtighten. The legs can be deformed
and cause malfunction.
13
Fit the front fender.
14
Refit the wheel and the front wheel shaft.
Do not tighten yet.
5 Nm
25 Nm
15
15
Fit the brake calipers on both sides.
16
Lower the motorcycle. Apply the front wheel
brake and push the front suspension down,
two or three times. This will put the fork legs
in a parallel position.
NOTE!
Another way is to rotate the wheel as fast as
possible and bring it to a fast stop by brak-
ing. This will bring the legs to the correct
position.
17
Tighten the wheel shaft and shaft clamps
so the fork legs are in fixed position. Tighten
the fender and caliper brackets. See the
Workshop manual for tightening torques.
NOTE!
Make sure that all bolts are tightened in cor-
rect torque and that nothing restrains the
front fork when the suspension is beeing
compressed or extended. Check with the
Workshope manual of the motorbike.
WARNING!
Certain modifications can be necessary to
install the Öhlins front fork. It is vital that the
mounting instructions are carefully followed
18
Continue your work according to the Owners
manual, section Adjustments.
10 Nm
5 Nm
-
1
-
2
-
3
-
4
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Ohlins FG330 Mounting Instruction
-
-
-
-
-
-
-
-
-