TAFFIO KM3D-360 Installation guide

1

TAFFIO® 360° Camera-System Parking

System

Article No.: KM3D-360

2

3

4

Catalogue

Inhalt

Product Introduction

................................................ 5

Specifications

...................................................... 5

Features:

......................................................... 6

1. Display interface ..................................................................... 7

5. Display settings: .................................................................... 19

7. Version information .................................................................. 24

8. Wireless knob ...................................................................... 25

5

Product Introduction

The three-dimensional 360-degree panoramic visual parking assist system uses 4 ultra-wide-angle

cameras installed on the front, rear, left, and

The images around the vehicle are collected at time, and after correction and stitching by the image

processing unit, a 360-degree three-dimensional panorama around the vehicle is formed, which is

transmitted to the display device of the center console in real time.

Through the 360-degree panoramic visualization system, the driver can intuitively see the location of

the vehicle and the obstacles around the vehicle from the vehicle, and calmly control the vehicle to park

and pass through complex roads, effectively reducing scratches, collisions, and obstacles. The occurrence

of accidents such as sinking.

Specifications

Host working voltage

DC 12V

Camera supply voltage

5.0V

Working current

700mA@12V

Working temperature

-30℃-85℃

Storage temperature

-40℃-100℃

Video input

4 channels 720P AHD signal input

Video output format

CVBS/VGA/AHD/TVI

Video storage

U Disk 8GB/16GB/32GB

Video file format

MP4

CPU

Allwinner T7 Cortex-A7 6 core

Main frequency

1GHZ

FLASH

4GB

GPU

Mali-400 MP4

6

Features:

1. Multiple video output methods: CVBS, VGA, AHD, TVI;

2. Multiple viewing angles: including more than a dozen viewing angles, covering all

customer use scenarios;

3. Knob control: One key to open/close 360, various view angles can be switched

instantly;

4. True 3D: 3D viewing angle can be switched in any direction;

5. Various dynamic effects: door switch, wheel speed/direction, forward/backward,

3D stereo radar real-time display;

6. Built-in dozens of 3D car models: built-in 3D car models of dozens of hot-selling

models, which are still increasing;

7. The license plate number can be customized and entered at will. 7 colors of each

car model can be switched arbitrarily;

8. Support dual CAN gussets, insert dual CAN boards into dual CAN 3D all-in-one in

seconds;

9. You can choose the style of each trajectory line, the radar starts, and the

trajectory follows;

10. Parking monitoring, one shot per second, up to 24 hours parking monitoring;

11. Compatible with Haisi's calibration cloth, two large cloth manuals, two large and

two small manuals, two large and two small automatics;

12. The size of the 3D viewing angle, the height of the viewing angle, the 3D

elevation, and the length of the 3D car model can be adjusted, so that there is

no ghost on the top of the 3D. When displayed on any screen, the 3D car model

is of normal proportions and will not be stretched;

7

Detailed product function

1. Display interface

The display modes include: 2D display, 3D display, narrow-lane limited width

mode,

front-to-rear wide-angle, front and rear view zoom, and so on.

1. 2D pre-streaming 2. 2D front display

3. 2D front zoom (front of the car) 4. 2D post-streaming

5. 2D front view 6. 2D rear zoom (car rear)

8

7. Horizontal 2D 8. The front and left are displayed at the same time

9. The body is displayed at the same time 10. 3D left view

11. 3D rear view 12. 3D right view

13. 3D rotating view

9

2. Menu interface

Main menu functions: driving record, video setting, control setting, panoramic debugging, display setting,

system setting, version information

10

1. Driving record

1.1 Press the direction keys of the remote control (or the previous page and the

next page of the menu) to find the time period video file to be played. The

selected video file will have a "√" after pressing the OK button.

1.2 After selecting the video file, click the "Play" menu to enter the playback

interface. The default is 4 cameras at the same time playback. You can select the

up, down, left, and right direction keys in the function menu below to play back

the front, back, left, and right separate cameras. You can also choose to pause

and fast forward. , Fast rewind function icon operation.

1.3 Lock and protect important video files. After the selected video file is

marked with "√", click the "lock" menu below. The locked video file has a

"lock" icon in front of it, so that the locked video file will not be It is

overwritten by the system's automatic loop recording. The locked recording file

can be unlocked through the "Unlock" menu below, and the lock icon

disappears.

1.4 You can manually delete the video files in the list (including the video files

protected by the lock). Select the file to be deleted and click the "Delete" menu

11

below to delete it.

1.5 When the host is powered on, the system will automatically record in a loop, and the

duration of each recording is 5 minutes.

12

2. Video settings

2.1 Video switch: off/on (default on), no video after closing, no red dot is displayed in the

upper left corner.

2.2 Storage location: USB

2.3 Format: After the U disk is formatted, all contents in the U disk will be cleared.

2.4 Time setting: Set the system time of the panoramic host.

13

3. Control settings

3.1 Start mode

Automatic start: 360 will start automatically after each ignition;

Smart start: 360 will not start automatically after each ignition, the user will reverse gear, turn,

and then start 360 when the P key is pressed;

3.2 Emergency light control

Simultaneous display of left and right: When the emergency light is turned on, the images of

the left and right cameras will be displayed at the same time;

Streaming media: when the emergency light is turned on, the front and back streaming media

screens will be displayed; off: when the emergency light is turned on, the 360 display will not

be switched;

3.3 Turn signal control

Turn on: the turn signal can turn on 360 panorama;

Off: the turn signal can't turn on 360 panorama;

3.4 Turn signal display

Corrected view: When the left and right turn signals are turned on, the left and right corrected

view is displayed;

3D view: when the left and right turn signals are turned on, the left and right 3D views are

14

displayed; Original view: when the left and right turn lights are turned on, the left and right

original views are displayed;

3.5 Radar start

Start: the radar can start 360 panorama;

Off: Radar cannot start 360 panorama;

3.6 Front and back view

Original view: the front and rear views are displayed as original views;

Corrected view: the front and rear views are displayed as corrected views;

3.6 Follow the trajectory

Open: When the front and back are displayed as the corrected view, the view will move with

the change of the track line;

Close: Close the track follow function;

3.7 Display delay

10 seconds: When the 360 is turned on, when the user does not perform any operation, the

360 will be automatically turned off after 10 seconds

30 seconds: When the 360 is on, when the user does not perform any operation, the 360 will

be automatically closed after 30 seconds

1 minute: When the 360 is turned on, when the user does not perform any operation, the 360

will be automatically turned off after 1 minute

5 minutes: When the 360 is turned on, when the user does not perform any operation, the 360

will be automatically turned off after 5 minutes

3.8 Encoder

Select the matching decoder model

15

4. Panorama adjustment:

4.1 Vehicle length (CM): The vehicle length is the actual distance between the front and rear

tuning cloths.

4.2 Vehicle width (CM): The vehicle width is the actual distance between the outer sides of the

tires on both sides of the vehicle body.

4.3 Left-Right Offset (CM): the distance from the front side of the fabric to the shortest point of

the left and right fabric.

4.4 Optical lens: Choose the corresponding lens according to the actual installed camera, there

are HK8296; HK8255......

4.5 Photosensitive chip: According to the actual installed camera, select the corresponding

photosensitive chip, there are SONY225; SC1233...

4.6 Automatic calibration

4.1.1 Tool preparation and precautions before automatic adjustment:

1. Two large and two small calibration cloths: front and rear calibration cloth size 4.4x1.2m; left

and right calibration cloth size 1.2x1.6m

16

2. 2~4 measuring tapes: the measuring range can measure more than 7.5M (inclusive).

3. Site requirements: 12 meters long / 6 meters wide and open and the ground should be

relatively balanced (not on slopes or places with uneven ground).

4. Environmental requirements: The daily light brightness is the best, not under the sun or in a

dark place, otherwise it will affect the splicing.

5. The front and back calibration cloth should be parallel to the car. Use a ruler to measure the

distance between the two large cloths on the left and the front and the two large cloths on the

right. The error should be less than 2cm.

17

4.7 Lens correction

When the calibration effect is not very good, you can enter the lens correction, and perform

lens correction on the four cameras, front, rear, left, and right.

Correction method:

1. Choose front, rear, left and right cameras;

2. Click "Lens Calibration"

3. Use the up, down, left, and right buttons on the remote control to move the red circle in the

figure above to make the red circle and the black vignetting corner of the camera concentric.

4. After adjusting into concentric circles, press ok on the remote control to complete the lens

correction of the camera

18

4.8 Manual calibration 1

4.8.1 Tool preparation and precautions before manual adjustment:

1. Calibration cloth: the front and back calibration cloth size is 4.4x1.2m; (the same as the

automatic splicing cloth, the size of the black grid on the cloth is 60x60 cm, when manual

splicing, the left and right calibration cloths are not used)

2. The placement position of the calibration cloth and the order of tracing points

4.9 Manual calibration 2

19

Tool preparation and precautions before manual adjustment:

1. Calibration cloth: the front and back calibration cloth size is 4.4x1.2m; (it is different from

manual calibration and automatic splicing cloth, the size of the black grid on the cloth is 1x1m)

2. The placement position of the calibration cloth and the order of tracing points

5. Display settings:

20

5.1 Output format

Users can set output formats such as NTSC/PAL, VGA1280_720, VGA720_480, VGA720_576,

AHD, TVI, etc.

5.2 Language setting

Simplified Chinese by default

5.3 Power-on rotation

Turn on: 360 turns on the automatic 3D rotation function. Turn off: 360 turns on without the

automatic 3D rotation function.

5.4 Color management

The brightness, saturation, contrast, and sharpness of the displayed image can be adjusted.

The adjustment range is 0~100, and the default value is 50.

5.5 2D position

You can set whether the 2D view is on the left or on the right

5.6 3D view adjustment

Page is loading ...

TAFFIO KM3D-360 Installation guide

Related papers

Other documents