Pac-Audio CAM-TY12 Reverse Camera Harness Operating instructions

Brand: Pac-Audio

Model: CAM-TY12 Reverse Camera Harness

Category: Car kits

Type: Operating instructions

This manual is also suitable for

PAC-audio CAM-TY12 Reverse Camera Harness

Pac-Audio PAC-audio CAM-TY12 Reverse Camera Harness is a T-harness that allows you to add a reverse camera input to compatible Toyota and Scion OEM touchscreen radios or retain the factory camera when replacing the factory radio. Simple plug and play installation makes it easy to use.

With this harness, you can connect an aftermarket camera to your OEM radio, providing a +6v power output if needed. However, if your camera requires +12v, you'll need to find a reliable source of +12 volt ACC power.

The CAM-TY12 also allows you to retain the factory reverse camera with an aftermarket radio.

CAM-TY12

Reverse Camera T-Harness for

Select Toyota & Scion Vehicles

www.pac-audio.com

Rev. 01182016

P ifi A C ti

Pacific Accessory Corporation® | 866-931-8021 | [email protected]

Introduction & Features

Installation:

Illustration / Schematic

The CAM-TY12 is a reverse camera T-harness that gives the ability to either add a reverse camera input for compatible

TOYOTA and SCION OEM touchscreen radios or retain the factory camera when replacing the factory radio. Simple plug and

play installation.

1. Disassemble dash and remove the radio.

2. Disconnect the 24 pin connector from the back of the factory radio (if equipped) and install the T-harness.

3. Connect the RCA from the aftermarket camera to the female RCA located in the T-harness

3. The OEM radio, when connected to this harness, will provide a +6v power output if needed. Most aftermarket cameras

require +12v for power, if your camera requires +12v then you will need to find a reliable source of +12 volt ACC power. If

not being used please insulate the pin located at the end of the red wire.

4. To function properly the camera must have power before the vehicle is placed into reverse, so using the reverse lamp as a

power source is not recommended for proper functionality.

5. Normally a reverse trigger is provided by the vehicle manufacturer, as long as the camera has power when the vehicle is placed into

reverse, the radio should automatically switch to the reverse camera. In the event that the radio does not automatically switch

to the reverse camera a +12v reverse signal will need to be added to Pin 2 of the 28 pin connector. See Fig 1.

When adding a reverse camera to an OEM radio:

When retaining the factory reverse camera with an aftermarket radio:

1. Connect the factory 24 pin camera harness to the T-harness.

2. Connect the male side of the RCA into the aftermarket radios reverse camera input.

3. Connect the loose black wire to chassis ground.

4. Insert the pin located on the end of the red wire into the pin 12 location in the 20 pin connector of the RP4.2-TY11. This

pin is located next to the red/white programmable +12v output. See Fig. 2. If an RP4.2-TY11 is not being used along with this

harness then the red wire will need to connect to +6v. This may require an adapter to step down the voltage from +12v to +6v.

Fig. 2

Fig. 1

• •

Rearvi~ew

Camera

Retention

Addition

H•arness

for

Select

2014.5·2016

Toyota

and

Scion

Automobiles

Equipped

With

6.1"Disp

Radios

Pac-Audio CAM-TY12 Reverse Camera Harness Operating instructions

Brand: Pac-Audio

Model: CAM-TY12 Reverse Camera Harness

Category: Car kits

Type: Operating instructions

This manual is also suitable for

PAC-audio CAM-TY12 Reverse Camera Harness

The CAM-TY12 also allows you to retain the factory reverse camera with an aftermarket radio.

Download PDF

report

Pac-Audio CAM-TY12 Reverse Camera Harness Operating instructions

This manual is also suitable for

Pac-Audio CAM-TY12 Reverse Camera Harness Operating instructions

Other documents