Zevni Z-F8MZREVQ-46W2 User manual

Brand: Zevni

Model: Z-F8MZREVQ-46W2

Type: User manual

[email protected]

Page: - 1 - / 3

Item Number: Z-F8MZREVQ-46W2

WARNING (To reduce the risk of fire, electric shock, or personal injury):

1. We suggest installation by a licensed electrician.

2. Please read the instruction carefully and save it as you may need it at a later time.

3. Before you start, NEVER attempt any work without shutting off the electricity until the work is done.

Go to the main fuse, or circuit breaker, box in your home.

Place the main power switch in the “OFF” position.

Place the wall switch in the “OFF” position.

4. Mounting surface should be clean, dry, flat, strong enough and 1/4” larger than the canopy on all sides. Any gaps

between the mounting surface and canopy exceeding 3/16” should be corrected as required.

5. Make sure that the ceiling or wall can stand the weight of the lamp before installation.

6. Make sure the voltage you are using is 120V. The maximum wattage is 60W per bulb.

7. Keep the lamp away from acidic and alkaline substances in case of damaging the surface of the lamp.

8. When replacing bulbs, you should turn off or unplug the lamp and you must wait until it is cool as bulbs get hot

quickly.

9. The safety instructions appearing in this manual are not meant to cover all possible conditions that may occur. It

must be understood that common sense, caution and care must be used with any electrical products.

IMAGE FOR FINISHED PRODUCT:

TOOLS REQUIRED

(NOT INCLUDED):

Before starting assembly and installation please prepare the needed

tools as below picture

Ladder Philips Head or Flat

Blade Screwdriver Electrical Tape Pilers Wire Cutter/Stripper

[email protected]

Page: - 2 - / 3

ASSEMBLY & INSTALLATION INSTRUCTIONS:

1. Carefully remove the fixture from the carton and check that all parts and accessories are

included as shown in the above illustration.

2. Turn off power

Before you start the installation, NEVER attempt any work without shutting off the electricity

until the work is done.

PARTS INCLUDING:

(D) Mounting plate (1)

(E) Back plate (1)

(F) Knob nut (2)

(G) Socket (2)

(H) Lampshade (2)

(I) Socket ring (2)

ACCESSORIES ENCLOSED:

(A) Mounting screw (2)

(B) Plastic wire connector (3)

3. Make assembly

Go to the main fuse, or circuit breaker, box in your home.

Place the main power switch in the “OFF” position.

Place the wall switch in the “OFF” position.

[email protected]

Page: - 3 - / 3

4. Check everything is installed properly, then you could turn on the light. Enjoy!

Step A1 »

Step A2 »

Step A3 »

Unscrew knob nuts (F) from back plate (E), then set them aside for later installation.

Carefully pass the supply wires from the outlet box through mounting plate (D).

Secure mounting plate (D) to the outlet box with mounting screws (A).

Make wire connections

Connect wires as below wires connection shown.

PLEASE NOTE THAT GROUND WIRE IS BARE

COPPER WIRE, NEVER CONNECT OTHER WIRES TO GROUND WIRES.

Twist wires together with plastic wire connectors until tightly joined, and wrap each

connector with approved electrical tape. Be sure that no wire strands are exposed and then

carefully tuck all wires into the outlet box.

Step A4 » Align the holes in back plate (E) with the pre-assembled mounting screws, then attach back plate

(E) to mounting plate (D) with the previously removed knob nuts (F). Hand tighten until snug.

NOTE: back plate (E) should be snug against the wall with knob nuts (F).

If not, remove back plate (E), adjust the threaded length of pre-assembled

mounting screws on mounting plate assembly (D):

• Unscrew the pre-assembled hex nuts.

• Screw the pre-assembled mounting screws in or out of mounting plate (D).

• When the secure length is achieved, tighten the pre-assembled hex nuts and

back to Step A4.

Step A5 » 1) Remove socket rings (I) from sockets (G), and carefully place lampshades (H) on sockets (G),

then secure them with socket rings (I).

2) Install bulbs (Not included) (Please do not exceed the maximum wattage recommended on the

socket.)

ORDERING PARTS

Keep this sheet for future reference in case you need

to order replacement parts. All parts for this fixture can

be ordered from the place of purchase. Be sure to use

exact wording from illustration when ordering parts.

CLEANING

To clean, wipe the fixture with a soft cloth. Do not use

abrasive materials such as scouring pads or powders,

steel wool or abrasive paper.

Connect Black or

Red Supply Wire to: Connect

White Supply Wire to:

Black White

*Parallel cord (round & smooth) *Parallel cord (square & ridged)

Clear, Brown, Gold or Black without

tracer Clear, Brown, Gold or Black with

tracer

Insulated wire(other than green)

with copper conductor Insulated wire(other than green)

with silver conductor

* Note: When parallel wires (SPT I&

SPT ll) are used. The neutral wire is

square shaped or ridged and the

other wire will be round in shape or

smooth (see illus.)

OUTLET BOX

GROUND

DIMPLES

GREEN GROUND

SCREW

CUPPED

WASHER

FIXTURE

GROUND

Neutral Wire

GREEN GROUND

SCREW

OUTLET BOX

GROUND

FIXTURE

GROUND

Connect ground wires according to the below chart Connect wires according to the below chart

Zevni Z-F8MZREVQ-46W2 User manual

Zevni Z-F8MZREVQ-46W2 User manual

Zevni Z-F8MZREVQ-46W2 User manual

Related papers

Other documents