Prince Castle 164-A Operating instructions

Brand: Prince Castle

Model: 164-A

Type: Operating instructions

OPERATING

INSTRUCTIONS

Manual Grill Tool Sharpener

Model No. 164-A

355 East Kehoe Blvd. l Carol Stream, IL 60188

Tel: (630) 462-8800

l Fax: (630) 462-1460

Toll Free: 1-800-PCASTLE

Printed in September 1997

Prince Castle Inc.

164-504

SPECIFICATION

164-A Dimensions

Length 17 (43.18 cm)

Width 8 (20.32 cm)

Height 7 (17.78 cm)

Shipping Weight 22lbs. (10 kg.)

The Prince Castle manual grill tool sharpener gives a

quick sharpened straight edge to scrapers and

spatulas. Sharp spatulas pick up grilled meat

cleanly without tearing the seared surface. Natural

juices are kept in food for more flavor, and a more

appetizing appearance. With precision edges

cleanup is quick and easy without scratching. Plus,

compact size of the manual grill tool sharpener

saves valuable counter space.

LIMITED WARRANTY

This product is warranted to be free from defects in

material and/or workmanship for a period of one

year from date of original installation, not to exceed

18 months from date of shipment from our factory.

Any component which proves to be faulty in material

and/or workmanship will be replaced or repaired (at

the option of Prince Castle, Inc.) without cost to the

customer for parts or labor.

This warranty is subject to the following exceptions/

conditions:

l Use of any non-genuine Prince Castle parts

voids this warranty. All genuine Prince Castle

replacement spare parts are warranted for ninety

(90) days from date of purchase.

l Damage caused by carelessness, neglect, and/

or abuse (e.g., dropping, tampering or altering

parts), equipment damaged in shipment, by fire,

flood or an act of God is not covered under this

warranty.

l This unit is portable, charges for on location

service (i.e. trip charges, mileage) are not in-

cluded in the provisions of the warranty.

TABLE OF CONTENTS PAGE

Installation..................................................................... 2

Operating ....................................................................... 2

Parts List....................................................................... 3

Troubleshooting ............................................................ 4

Non-scheduled Maintenance ....................................... 4

INSTALLATION

1. After you have removed the sharpener from the

carton, inspect the unit for signs of damage. If there

is damage to the unit:

l Notify carrier within 24 hours after delivery.

l Save carton and packing materials for inspection

purposes.

l Contact the Prince Castle Customer Sales

Department at 1-800-722-7853 to arrange for

a replacement to be sent.

2. Verify that all parts have been received.

3. Clean spatulas and scraper blades with soap and

water. Dry thoroughly before sharpening.

4. Assemble knob (item A in figure 1) to back frame of

sharpener.

IMPORTANT: The knob can be assembled to either

side of back frame depending if operator is left or right

handed.

OPERATION

5. Turn carriage knob (item C in figure 1) counter-

clockwise to open jaws.

6. Lift carriage assembly (item B in figure 1) by large

knob (item C in figure 1) upward until it stops. Hold

in this position.

8. Press gauge stop bar (item D in figure 1) tab

downward until it makes contact with stop pin (item

E in figure 1).

9. Insert meat spatula or grill scraper blade squarely

against gauge stop bar (item D in figure 1).

IMPORTANT: Center spatula in carriage.

10. Tighten jaws by turning carriage knob (item C in

figure 1) clockwise while holding carriage in the up

position.

11. Lift gauge bar (item D in figure 1) upward over

detent pin located on the side of the carriage. This

pin holds the gauge bar up.

12. Lower carriage assembly (item B in figure 1) with

tool to rest on the file.

13. While holding carriage knob (item C in figure 1) with

one hand and knob (item A in figure 1) with the

other, slide carriage back and forth on file, applying

moderate pressure. Continue until spatula has

good sharp edge.

14. Remove sharpened tool and burn from back side by

sliding along file.

15. Round corners by using a curve motion against the

edge of the file. Use the bar as a guide.

16. Wash tool, sanitize and dry.

CAUTION: Handle tool carefully to avoid

getting cut.

TO SHARPEN REDI-GRIL BLADES

1. Place blade in special holder over pins with beveled

side up. See figure 2.

2. Hold blade with fingers and turn holder over.

3. Insert tool in carriage assembly against gauge

stop.

4. Repeat steps three through 13 under operation.

figure 1

figure 2

ITEM PART NO. DESCRIPTION

1 164-33 Side Frame

2 164-32 Side Frame Support

3 164-31 File Support

4 164-27 File

5 164-70 Large File Clamp

6 164-71 Small File Clamp

7 164-60 Knob Assembly

8 164-28 File Cleaner Bracket

9 89-057 File Cleaner

10 164-62 Foot Kit (Pkg. of 4)

12 164-34 Rt. Hd. Bearing Bracket

13 164-35 Lt. Hd. Bearing Bracket

14 164-26 Carriage Shaft

15 164-39 Carriage Bumper

16 62-016 Flange Bearing Plastic

17 164-48 ASlide Locking Plate

18 578-294 Mounting Bar Assembly

18a 578-239 Clamping Handle Stem

18b 578-255 Locking Jaw Mounting Bar

18c 89-305 Basic External Retaining Ring

19 164-58S Knob

20 76-384 Set Screw

21 68-003 Roll Pin

22 89-582 Spring Plunger

23 164-38 Gauge Stop

24 164-43 Spacer

EXPLODED VIEW

ITEM PART NO. DESCRIPTION

25 578-282S Scraper Holder Assembly

(optional)

26 578-259 Scraper Holder

27 152-45 Handle

A 76-509 Screw Hex Head Cap

68/16 X 7/8

79-077 Washer, Flat 3/8 I.D.

B 76-311 Screw Hex Head

1/4-20 X 1

79-032 Washer, Flat 3/8 I.D.

C 76-506 Screw Soc. Head Cap

10-24 X 1/2

(Part of 164-62)

D 76-021 Screw Rd. Hd.

6-32 X 1/4

E 76-261 Screw Soc. Head Cap

1/4-20 X 7/8

73-022 Nut, Hex, 1/4-20

F 76-508 Screw Soc. Head Cap

5/16-18 X 3/4

H 76-507S Screw Soc. Head Cap

10-24 X 3/4 (Pkg. of 12)

J 76-061 Screw Hex Head

1/4-20 X 3/4

79-032 Washer, Flat .281 I.D.

K 73-086 Nut

79-028 Washer

PARTS LIST

TROUBLESHOOTING GUIDE

NON-SCHEDULED MAINTENANCE

Under normal conditions with proper use and cleaning,

very little non-scheduled maintenance is required for

this unit. However, this section provides procedures for

checking and replacement of the various parts used

within the cabinet in the event that it becomes neces-

sary. Before replacement of any parts, refer to the

troubleshooting guide above. This guide will assist in

determining the cause of any malfunction to insure

maintenance is required.

To change file or change to new position on existing

file:

A. Remove (2) screws. See item A in figure 3.

B. Turn file 180 degrees.

C. Tighten screws.

D. To use other positions of file, reverse file clamps.

See item B in figure 3.

figure 3

PROBLEM

Tool edge not Tool not lined up properly in carriage Reposition tool in carriage holder.

parallel. against gauge stop.

File worn. Reposition file to new surface.

IMPORTANT: The file can be turned to four

positions.

PROBABLE CAUSE

CORRECTIVE ACTION

Prince Castle 164-A Operating instructions

Prince Castle 164-A Operating instructions

Prince Castle 164-A Operating instructions

Related papers

Other documents