Urbanworx UXLAP11 User manual

Type
User manual

This manual is also suitable for

UXKIDHB/UXKIDHP
Kids Wireless
Headphones
INSTRUCTION MANUAL
CONTENTS
SAFETY INSTRUCTIONS 3
PRODUCT OVERVIEW 4
PAIRING AND CONNECTION 5
FUNCTION AND OPERATION 6
HOW TO CHARGE 6
SPECIFICATIONS 7
SAFETY INSTRUCTIONS
WARNINGS
Read the below warnings thoroughly before your start using your
headphones. Store this quick start guide, warranty and receipt
alongside with product packaging. The safety precaution instructions
reduce the risk of re and injury when correctly complied to.
SAFETY RULES
Please pay attention to sharp edges, uneven surfaces, metal parts,
accessories and packaging to avoid any possible damage.
Please do not dismantle and repair this product. This may cause re,
electronic breakdown or complete damage to the product, which is
not covered by the warranty.
Please do not wipe this product with oil or other active liquids.
Please pay attention to waterproong, otherwise it will cause serious
damage to the headsets. The manufacturer will not guarantee the
damage caused by water.
Do not place the headsets in an environment where there is water
or where the temperature is too low or too high (normal use
temperature is between -10C-45°).
Do not use headsets during thunderstorms. Thunderstorms can
cause the headsets to work abnormally and increase the risk of
electric shock.
Page 3
PRODUCT OVERVIEW
Page 4
Charging port
3.5 Jack
TF card slot
Built-in microphone
PACKAGING CONTENTS:
PAIRING AND CONNECTION
1. Keep the distance between the mobile phone and the headset
within one meter, the closer the better.
2. Press " " button for about 5 seconds and release when the
indicator light ashes red and blue alternately, the headset has
entered the pairing mode.
3. Turn on the Bluetooth function the mobile phone, search for
devices, and select UXKIDHB for Blue and UXKIDHP for Pink,
to pair and connect. When the connection is successful, the
headset indicator light ashes blue slowly.
4. After the pairing is completed, the headset and the mobile phone
will remember each other, and there is no need to pair them again
the next time you use them. When the mobile phone is turned on
the headset will automatically connect after turning on.
Page 5
HOW TO CHARGE
FUNCTION AND OPERATION
1. Use DC5V/1A charger;
2. Connect the charger to the earphone charging port;
3. When charging, the indicator light is red;
4. After the earphone is fully charged, the indicator light goes out.
Play/Pause: Press the" " key once
Volume Plus: Press the " + " key to increase the volume;
Volume Down: Press the " - " key to reduce the volume;
Last Song: Long press " - " to play the last music;
Next Song: Long press " + " to play the next music;
Shutdown: Press " " for 6 seconds in standby or working mode (voice
prompt "power o" and red indicator light ashes 3 times);
Low-Power Alarm: (red indicator light ashes slowly, and there is a
low-power prompt tone;
Charging: Insert the charger into the headset charging port (the red
indicator light is on);
Answer the phone: Short press " " to answer the phone;
End the call: Short press " " to end the call;
Refuse to answer the phone: Long press " " for about 2 seconds;
Bluetooth/TF mode: Long press " " for about 2 seconds, with a prompt
tone;
Page 6
SPECIFICATIONS
Connection distance: >10 meters
Wireless version: V5.1
Play time: Up to 8 hours
Protocol: A2DPHFPHSP AVRCP\SPP
Talking time: More than 10 hours
Battery type/ specication: Polymer lithium battery 3.7V 400mAh
Charging time: 2-3 hours
Speaker Impedance: 32Ω
Standby time: 300 hours
Charging mode: Type-c charging interface
Page 7
CUSTOMER SUPPORT
info@ayonz.com
DISTRIBUTED BY:
Ayonz Pty Ltd
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

Urbanworx UXLAP11 User manual

Type
User manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI