B-K lighting Twin Delta Star - MR16 Installation guide

Brand
B-K lighting
Model
Twin Delta Star - MR16
Type
Installation guide

B-K Lighting Twin Delta Star - MR16

The B-K Lighting Twin Delta Star - MR16 is a versatile and powerful lighting fixture designed for a wide range of indoor and outdoor applications. With its sleek design and advanced features, the Twin Delta Star - MR16 offers exceptional illumination and energy efficiency.

Key Features:

  • Adjustable Beam Angle: Customize the beam angle from a narrow 15 degrees to a wide 60 degrees, providing precise control over light distribution.
  • Interchangeable Optics: Easily switch between different optic lenses (sold separately) to achieve the desired beam pattern and light effect.

B-K Lighting Twin Delta Star - MR16

The B-K Lighting Twin Delta Star - MR16 is a versatile and powerful lighting fixture designed for a wide range of indoor and outdoor applications. With its sleek design and advanced features, the Twin Delta Star - MR16 offers exceptional illumination and energy efficiency.

Key Features:

  • Adjustable Beam Angle: Customize the beam angle from a narrow 15 degrees to a wide 60 degrees, providing precise control over light distribution.
  • Interchangeable Optics: Easily switch between different optic lenses (sold separately) to achieve the desired beam pattern and light effect.
RELEASED
7-30-18
REFERENCE NUMBER
INS-2264-00
40429 Brickyard Drive • Madera, CA 93636 • USA
559.438.5800 • FAX 559.438.5900
www.bklighting.com • [email protected]
B-K LIGHTING
THIS DOCUMENT CONTAINS PROPRIETARY INFORMATION OF B-K LIGHTING, INC. AND ITS RECEIPT OR POSSESSION DOES NOT CONVEY ANY RIGHTS TO REPRODUCE, DISCLOSE ITS CONTENTS, OR TO MANUFACTURE, USE OR SELL ANYTHING IT MAY
DESCRIBE. REPRODUCTION, DISCLOSURE OR USE WITHOUT SPECIFIC WRITTEN AUTHORIZATION OF B-K LIGHTING, INC. IS STRICTLY FORBIDDEN.
IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE THESE INSTALLATION INSTRUCTIONS
TOOLS
NEEDED:
By Others
• Product must be installed by a qualified person in a manner
consistent with its intended use and in compliance with the
National Electrical Code, Canadian Electrical Code, and all Local
and Provincial Codes.
• Follow product label information and instructions.
• Qualified Personnel must perform all servicing or relamping of
this product.
• Before wiring to power supply and during servicing or relamping,
turn off power at fuse or circuit breaker before service.
• The use of accessory equipment not recommended by the
manufacturer or installed contrary to instructions may cause an
unsafe condition. The use of damaged components may cause
an unsafe condition and void product warranty.
IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE ALL SAFETY
AND INSTALLATION INSTRUCTIONS
• Do not block light emanating from product in whole or part, as
this may cause an unsafe condition.
• Never operate the fixture with missing or damaged lens.
Lens must be cleaned on regular basis.
• Entire fixture may become extremely hot. Do not touch hot
lens or fixture body. Do not touch the lamp at any time. Use
a clean, dry, soft cloth to handle the lamp. Oil from skin may
damage the lamp and cause it to rupture.
• Replace lamp only with correct wattage and type of lamp
marked on fixture label.
• All gaskets, o-rings and sealing surfaces must be kept clean
during installation and service; failure to do this may cause an
unsafe condition and void product warranty.
INSTRUCTIONS PERTAINING TO
A RISK OF FIRE, OR INJURY TO
PERSONS IMPORTANT SAFETY
INSTRUCTIONS
Lighted lamp is HOT!
WARNING - To reduce the risk of FIRE OR INJURY TO PERSONS:
Turn off/unplug and allow to cool before replacing lamp.
Lamp gets HOT quickly! Contact only switch/plug when
turning on.
Do not touch hot lens, guard, or enclosure (see diagram/
picture).
Keep lamp away from materials that may burn.
Do no touch the lamp at any time. Use a soft cloth. Oil
from skin may damage lamp.
Do not operate the luminaire fitting with a missing or
damaged shield.
SAVE THESE INSTRUCTIONS
· Suitable for wet locations
IMPORTANT LISTINGS AND CERTIFICATIONS
Warning Hot Surface
Installation Instructions
L.O.C.K.™
Mounting
System
Nite Star™
Fixture
1/8”, 5/32”, & 5/64” Allen Wrench
Waterproof Wire Connectors
Flammable
Canopy
Low Voltage
TECHNOLOGY
with TECHNOLOGY
SN-A
SN-B SN-C SN-D SN-G
SN-L
& Low Voltage SIGN STAR™ & TWIN SIGN STAR™
2 1/4"
(57mm)
5"
(127mm)
4"
(102mm)
S000997
Locking O-Ring
Compression
Knuckle
5"
(127mm)
3/8"
(10mm)
Locking O-Ring
Compression
Knuckle
(105mm)
4 1/8"
2 1/4" Dia.
(57mm)
2 1/4" Dia.
(57mm)
4"
(102mm)
Specify Inches 18"- 36" Maximum
(457mm - 914mm)
Specify Inches 18"- 48" Maximum
(457mm - 1219mm)
(283mm)
11 1/8"
1" Dia.
(25mm)
1" Dia.
(25mm)
1" Dia.
(25mm)
(105mm)
4 1/8"
Patent Pending
Adjust-e-Lume®
Patent Pending
Adjust-e-Lume®
(283mm)
11 1/8"
ST-B
Locking O-Ring
Compression
Knuckle
4 1/8"
(105mm)
ISO VIEW
ST-C-LED
S000998:
1" Dia.
(25mm)
Locking O-Ring
Compression
Knuckle
1" Dia.
(25mm)
4 1/8"
(105mm)
2 1/4" Dia.
(57mm)
2 1/4" Dia.
(57mm)
4"
(102mm)
4"
(102mm)
3/8"
(10mm)
Specify Inches 18"- 48" Maximum
(457mm - 914mm)
3 1/8"
(79mm)
2 1/4"
(57mm) Specify Inches 18"- 36” Maximum
(457mm - 1219mm)
3 1/8"
(79mm)
Patent Pending
Adjust-e-Lume®
Patent Pending
Adjust-e-Lume®
ST-C
2 1/4"
(57mm)
Compression
Locking O-Ring
Knuckle
(295mm)
11 5/8"
(105mm)
4 1/8"
S000996
ST-A-LED
3/8"
(10mm)
Locking O-Ring
Knuckle
Compression
(295mm)
11 5/8"
Specify Inches 18"- 36" Maximum
(457mm - 914 mm)
1" Dia.
(25mm)
Specify Inches 18"- 48" Maximum
(457mm - 1219mm)
1" Dia.
(105mm)
4 1/8"
2 1/4" Dia.
(57mm)
2 1/4" Dia.
(57mm)
(102mm)
4"
(102mm)
4"
Patent Pending
Adjust-e-Lume®
Patent Pending
Adjust-e-Lume®
ST-A
Please refer to the low voltage design guide at www.bklighting.com/lvguide before installation for proper wire selection.
This set of instructions works for:
SN-A - Sign Star™ Style “A”
SN-B - Sign Star™ Style “B”
SN-C - Sign Star™ Style “C”
SN-D - Sign Star™ Style “D”
SN-L - Sign Star™ Style “L”
SN-F - Sign Star™ Style “F”
SN-G - Sign Star™ Style “G”
ST-A - Twin Sign Star™ Style “A
ST-B - Twin Sign Star™ Style “B”
ST-C - Twin Sign Star™ Style “C”
ST-F - Twin Sign Star™ Style “F”
ST-G - Twin Sign Star™ Style “G”
SN-F
ST-F ST-G
40429 Brickyard Drive • Madera, CA 93636 • USA
559.438.5800 • FAX 559.438.5900
www.bklighting.com • [email protected]
B-K LIGHTING
IMPORTANT SAFETY INFORMATION LISTED ON REVERSE
READ, FOLLOW, AND SAVE ALL SAFETY AND INSTALLATION INSTRUCTIONS
RELEASED
7-30-18
REFERENCE NUMBER
INS-2264-00
Standard Installation Instructions
Phase 1 - Rough In
Installation of Back box
1. Install Conduit (By Others) to be used with
this product.
2. Install junction box so that front face is flush
with finished wall. Seal building envelope as
per NEC.
3. Connect box to conduit and pull wires for
connections (See wiring diagram).
Additional Info
• Please follow National and Local electrical codes for your area.
• Suitable for through wire
• Suitable for installation into combustible materials.
• Rated for 90° C.
• Junction box, universal mounting ring screws, box mounting hardware
and gaskets (By Others)
Sign Star™ Style D (SN-D) shade must be installed facing downwards.
Installations where shade is facing upwards will VOID WARRANTY.
Phase 2 - Finish Installation of Fixture
TECHNOLOGY
with TECHNOLOGY
2. Make watertight connections from remote
transformer to fixture leads using waterproof
wire connectors. (By Others) See wiring diagram.
3. Mount canopy to junction box with universal
mounting ring using two (2) #10-24 stainless
steel black oxide screws with 1/8” Allen wrench.
Seal building envelope as per NEC. Do not
overtighten.
1. Install universal mounting ring (supplied with
fixture) with #10-24 screws using 1/8” Allen
wrench onto back box. Align fixture mounting
holes to final mounting position.
LINE 12V
Fixture
COM
Remote
Transformer
COM
4. Use 5/32” Allen wrench to loosen #10-32
stainless steel black oxide socket head cap screw
at the knuckle. Aim fixture to desired vertical
location. Tighten to secure aiming position.
& Low Voltage SIGN STAR™ & TWIN SIGN STAR™
WIRING DIAGRAM
LED - For use with 12VAC
remote transformer or magnetic
transformers only. B-K Lighting cannot
guarantee performance with third party
manufacturers’ transformers.
Low Voltage - For use with 12VAC remote
transformer.
5. Optional 360SL™: Use 5/64” Allen wrench to
loosen stainless steel set screw on the 360SL™
rotational mounting system and rotate to
desired horizontal location. Tighten to secure
aiming position.
Sign Star™ Style D (SN-D) shade must be
installed facing downwards.
RELEASED
7-30-18
REFERENCE NUMBER
INS-2264-01
40429 Brickyard Drive • Madera, CA 93636 • USA
559.438.5800 • FAX 559.438.5900
www.bklighting.com • [email protected]
B-K LIGHTING
THIS DOCUMENT CONTAINS PROPRIETARY INFORMATION OF B-K LIGHTING, INC. AND ITS RECEIPT OR POSSESSION DOES NOT CONVEY ANY RIGHTS TO REPRODUCE, DISCLOSE ITS CONTENTS, OR TO MANUFACTURE, USE OR SELL ANYTHING IT MAY
DESCRIBE. REPRODUCTION, DISCLOSURE OR USE WITHOUT SPECIFIC WRITTEN AUTHORIZATION OF B-K LIGHTING, INC. IS STRICTLY FORBIDDEN.
IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE THESE INSTALLATION INSTRUCTIONS
Standard Installation Instructions
TECHNOLOGY
with TECHNOLOGY
& Low Voltage SIGN STAR™ & TWIN SIGN STAR™
POWER CANOPY™
TOOLS
NEEDED:
By Others
• Product must be installed by a qualified person in a manner
consistent with its intended use and in compliance with the
National Electrical Code, Canadian Electrical Code, and all Local
and Provincial Codes.
• Follow product label information and instructions.
• Qualified Personnel must perform all servicing or relamping of
this product.
• Before wiring to power supply and during servicing or relamping,
turn off power at fuse or circuit breaker before service.
• The use of accessory equipment not recommended by the
manufacturer or installed contrary to instructions may cause an
unsafe condition. The use of damaged components may cause
an unsafe condition and void product warranty.
IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE ALL SAFETY
AND INSTALLATION INSTRUCTIONS
• Do not block light emanating from product in whole or part, as
this may cause an unsafe condition.
• Never operate the fixture with missing or damaged lens.
Lens must be cleaned on regular basis.
• Entire fixture may become extremely hot. Do not touch hot
lens or fixture body. Do not touch the lamp at any time. Use
a clean, dry, soft cloth to handle the lamp. Oil from skin may
damage the lamp and cause it to rupture.
• Replace lamp only with correct wattage and type of lamp
marked on fixture label.
• All gaskets, o-rings and sealing surfaces must be kept clean
during installation and service; failure to do this may cause an
unsafe condition and void product warranty.
INSTRUCTIONS PERTAINING TO
A RISK OF FIRE, OR INJURY TO
PERSONS IMPORTANT SAFETY
INSTRUCTIONS
Lighted lamp is HOT!
WARNING - To reduce the risk of FIRE OR INJURY TO PERSONS:
Turn off/unplug and allow to cool before replacing lamp.
Lamp gets HOT quickly! Contact only switch/plug when
turning on.
Do not touch hot lens, guard, or enclosure (see diagram/
picture).
Keep lamp away from materials that may burn.
Do no touch the lamp at any time. Use a soft cloth. Oil
from skin may damage lamp.
Do not operate the luminaire fitting with a missing or
damaged shield.
SAVE THESE INSTRUCTIONS
· Suitable for wet locations
IMPORTANT LISTINGS AND CERTIFICATIONS
Warning Hot Surface
L.O.C.K.™
Mounting
System
Nite Star™
Fixture
5/32” & 5/64” Allen Wrench
Waterproof Wire Connectors
Mounting Hardware
Flammable High Voltage
SN-F
SN-B SN-C SN-D
SN-A SN-L
ST-B ST-C
ST-A
Power Canopy™
This set of instructions works for:
SN-A - Sign Star™ Style “A”
SN-B - Sign Star™ Style “B”
SN-C - Sign Star™ Style “C”
SN-D - Sign Star™ Style “D”
SN-L - Sign Star™ Style “L”
SN-F - Sign Star™ Style “F”
SN-G - Sign Star™ Style “G”
ST-A - Twin Sign Star™ Style “A
ST-B - Twin Sign Star™ Style “B”
ST-C - Twin Sign Star™ Style “C”
ST-F - Twin Sign Star™ Style “F”
ST-G - Twin Sign Star™ Style “G”
SN-G
ST-F ST-G
Phase 1 - Rough In
Installation of Back box
1. Install conduit and junction box (By Others)
to be used with this product.
2. Install junction box so that front face is flush
with finished wall or ceiling. Seal building
envelope as per NEC.
3. Connect box to conduit and pull wires for
connections (See Wiring diagram).
Additional Info
• Please follow National and Local electrical codes for your area.
• Suitable for through wire
• Suitable for installation into combustible materials.
• Rated for 90° C.
• Junction box, universal mounting ring screws, box mounting hardware and
gaskets (By Others)
Sign Star™ Style D (SN-D) shade must be installed facing downwards.
Installations where shade is facing upwards will VOID WARRANTY.
WIRING DIAGRAM
Phase 2 - Finish Installation of Fixture with Power Canopy.
1. Remove wire entrance knockouts as needed on
wall plate. Pull primary branch circuit through
knockout(s). Attach wall plate to junction box using
appropriate hardware (By Others).
2. Ground primary branch circuit to wall plate
per NEC. Make watertight connections from
transformer to primary branch circuit using
waterproof wire connectors (By Others).
See wiring diagram.
3. Connect fixture to transformer with provided
quick disconnect.
4. Mount canopy to wall plate using four (4)
#8-32 stainless steel button head screws with
5/64” Allen wrench. Seal building envelope
as per NEC. Do not overtighten.
Standard Installation Instructions
TECHNOLOGY
with TECHNOLOGY
& Low Voltage
40429 Brickyard Drive • Madera, CA 93636 • USA
559.438.5800 • FAX 559.438.5900
www.bklighting.com • [email protected]
B-K LIGHTING
IMPORTANT SAFETY INFORMATION LISTED ON REVERSE
READ, FOLLOW, AND SAVE ALL SAFETY AND INSTALLATION INSTRUCTIONS
RELEASED
7-30-18
REFERENCE NUMBER
INS-2264-01
5. Use 5/32” Allen wrench to loosen #10-32
stainless steel black oxide socket head cap
screw at the knuckle. Aim fixture to desired
vertical location. Tighten to secure aiming
position.
6. Optional 360SL™: Use 5/64” Allen wrench to
loosen stainless steel set screw on the 360SL™
rotational mounting system and rotate to
desired horizontal location. Tighten to secure
aiming position.
SIGN STAR™ & TWIN SIGN STAR™
POWER CANOPY™
120V 12V
Fixture
COM
Remote
Transformer
COM
120V 12V
Fixture
COM
GROUND
WIRING DIAGRAM
Transformer
COM
GROUND ON PLATE
Sign Star™ Style D (SN-D) shade must be
installed facing downwards.
RELEASED
7-30-18
REFERENCE NUMBER
INS-2264-02
40429 Brickyard Drive • Madera, CA 93636 • USA
559.438.5800 • FAX 559.438.5900
www.bklighting.com • [email protected]
B-K LIGHTING
THIS DOCUMENT CONTAINS PROPRIETARY INFORMATION OF B-K LIGHTING, INC. AND ITS RECEIPT OR POSSESSION DOES NOT CONVEY ANY RIGHTS TO REPRODUCE, DISCLOSE ITS CONTENTS, OR TO MANUFACTURE, USE OR SELL ANYTHING IT MAY
DESCRIBE. REPRODUCTION, DISCLOSURE OR USE WITHOUT SPECIFIC WRITTEN AUTHORIZATION OF B-K LIGHTING, INC. IS STRICTLY FORBIDDEN.
IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE THESE INSTALLATION INSTRUCTIONS
Standard Installation Instructions
TECHNOLOGY
with TECHNOLOGY
& Low Voltage SIGN STAR™ & TWIN SIGN STAR™
UPM™ SURFACE MOUNT
• Product must be installed by a qualified person in a manner
consistent with its intended use and in compliance with the
National Electrical Code, Canadian Electrical Code, and all Local
and Provincial Codes.
• Follow product label information and instructions.
• Qualified Personnel must perform all servicing or relamping of
this product.
• Before wiring to power supply and during servicing or relamping,
turn off power at fuse or circuit breaker before service.
• The use of accessory equipment not recommended by the
manufacturer or installed contrary to instructions may cause an
unsafe condition. The use of damaged components may cause
an unsafe condition and void product warranty.
IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE ALL SAFETY
AND INSTALLATION INSTRUCTIONS
• Do not block light emanating from product in whole or part, as
this may cause an unsafe condition.
• Never operate the fixture with missing or damaged lens.
Lens must be cleaned on regular basis.
• Entire fixture may become extremely hot. Do not touch hot
lens or fixture body. Do not touch the lamp at any time. Use
a clean, dry, soft cloth to handle the lamp. Oil from skin may
damage the lamp and cause it to rupture.
• Replace lamp only with correct wattage and type of lamp
marked on fixture label.
• All gaskets, o-rings and sealing surfaces must be kept clean
during installation and service; failure to do this may cause an
unsafe condition and void product warranty.
INSTRUCTIONS PERTAINING TO
A RISK OF FIRE, OR INJURY TO
PERSONS IMPORTANT SAFETY
INSTRUCTIONS
Lighted lamp is HOT!
WARNING - To reduce the risk of FIRE OR INJURY TO PERSONS:
Turn off/unplug and allow to cool before replacing lamp.
Lamp gets HOT quickly! Contact only switch/plug when
turning on.
Do not touch hot lens, guard, or enclosure (see diagram/
picture).
Keep lamp away from materials that may burn.
Do no touch the lamp at any time. Use a soft cloth. Oil
from skin may damage lamp.
Do not operate the luminaire fitting with a missing or
damaged shield.
SAVE THESE INSTRUCTIONS
· Suitable for wet locations
IMPORTANT LISTINGS AND CERTIFICATIONS
Warning Hot Surface
L.O.C.K.™
Mounting
System
Nite Star™
Fixture
Flammable High Voltage
SN-F
SN-B SN-C SN-D
SN-A SN-L
ST-B ST-C
ST-A
1/8”, 5/64” & 5/32” Allen Wrench
Waterproof Wire Connectors
Hammer
Phillips Screwdriver
1/4” Drill Bit and Drill
Mounting Hardware
NEEDED
FOR
INSTALLATION:
By others
UPM™
Surface Mount
This set of instructions works for:
SN-A - Sign Star™ Style “A”
SN-B - Sign Star™ Style “B”
SN-C - Sign Star™ Style “C”
SN-D - Sign Star™ Style “D”
SN-L - Sign Star™ Style “L”
SN-F - Sign Star™ Style “F”
SN-G - Sign Star™ Style “G”
ST-A - Twin Sign Star™ Style “A
ST-B - Twin Sign Star™ Style “B”
ST-C - Twin Sign Star™ Style “C”
ST-F - Twin Sign Star™ Style “F”
ST-G - Twin Sign Star™ Style “G”
ST-F ST-G
SN-G
GroundHotNeutral
LAMP
BLUE
WHITE
GROUND
QUICK DISCONNECT
LINE (BLACK)
NEUTRAL (WHITE)
GROUND (GREEN)
BARE WIRE
IN UPM
RED
BLACK
BLUE
WHITE
GREEN
BALLAST
GroundHotNeutral
LAMP
BLUE
WHITE
GROUND
QUICK DISCONNECT
LINE (BLACK)
NEUTRAL (WHITE)
GROUND (GREEN)
BARE WIRE
IN UPM
RED
BLACK
BLUE
WHITE
GREEN
BALLAST
GroundHotNeutral
LAMP
BLUE
WHITE
GROUND
QUICK DISCONNECT
LINE (BLACK)
NEUTRAL (WHITE)
GROUND (GREEN)
BARE WIRE
IN UPM
RED
BLACK
BLUE
WHITE
GREEN
BALLAST
1. Prepare for final mounting position according to
designed lighting plan. 2. Drill holes into surface for ¼” fasteners (By
Others).
4. Remove Patented Knockout(s) as necessary
from the inside of the UPM housing. Leave
remaining unused knockouts in place to
maintain seal.
NOTE: Patented design featuring a silicone
‘O’ Ring allowing knockout to be tapped back
into place to renew seal integrity.
GroundHotNeutral
LAMP
BLUE
WHITE
GROUND
QUICK DISCONNECT
LINE (BLACK)
NEUTRAL (WHITE)
GROUND (GREEN)
BARE WIRE
IN UPM
RED
BLACK
BLUE
WHITE
GREEN
BALLAST
5. Attach the UPM housing at mounting brackets
with ¼” fasteners (By Others). Use suitable
mounting hardware for surface.
NOTE: Many methods exist to bolt to a flat
surface. The fixture is provided with mounting
brackets with ¼” holes.
6. Connect 3/4” conduit connector through female
threaded conduit entry.
NOTE: Surface conduit is a common entrance
for water if not properly sealed. Seal connector
threads and conduit with a suitable sealant
(Teflon tape, adhesive, etc.). Sealing the
conduit after knockouts are removed is
required to maintain warranty.
7. Pull branch circuit wiring necessary for
installation (By Others.)
GroundHotNeutral
LAMP
BLUE
WHITE
GROUND
QUICK DISCONNECT
LINE (BLACK)
NEUTRAL (WHITE)
GROUND (GREEN)
BARE WIRE
IN UPM
RED
BLACK
BLUE
WHITE
GREEN
BALLAST
8. Attach tether wire under screw head at the base
of the UPM housing and tighten. Slowly lower
the faceplate until tether is taut.
NOTE: Faceplate tether supplied with UPM
is designed as an installation aid and NOT a
safety cable. Do not add weight to, or drop
faceplate.
LINE 12V
FIXTURE
COM
Transformer
COM
GROUND GROUND IN HOUSING
9. Use waterproof wire connectors (By Others) to
connect transformer primary leads to branch
circuit wires. Connect incoming ground to
ground wire provided in UPM housing. See
wiring diagram.
GroundHotNeutral
LAMP
BLUE
WHITE
GROUND
QUICK DISCONNECT
LINE (BLACK)
NEUTRAL (WHITE)
GROUND (GREEN)
BARE WIRE
IN UPM
RED
BLACK
BLUE
WHITE
GREEN
BALLAST
3. Loosen (4) #6-32 captive screws using a 5/64”
Allen wrench and disconnect quick disconnect
to remove faceplate of UPM housing.
WIRING DIAGRAM
40429 Brickyard Drive • Madera, CA 93636 • USA
559.438.5800 • FAX 559.438.5900
www.bklighting.com • [email protected]
B-K LIGHTING
IMPORTANT SAFETY INFORMATION LISTED ON REVERSE
READ, FOLLOW, AND SAVE ALL SAFETY AND INSTALLATION INSTRUCTIONS
RELEASED
7-30-18
REFERENCE NUMBER
INS-2264-02
Standard Installation Instructions
TECHNOLOGY
with TECHNOLOGY
& Low Voltage
PROJECT:
TYPE:
SIGN STAR™ & TWIN SIGN STAR™
UPM™ SURFACE MOUNT
40429 Brickyard Drive • Madera, CA 93636 • USA
559.438.5800 • FAX 559.438.5900
www.bklighting.com • [email protected]
B-K LIGHTING
IMPORTANT SAFETY INFORMATION LISTED ON REVERSE
READ, FOLLOW, AND SAVE ALL SAFETY AND INSTALLATION INSTRUCTIONS
RELEASED
7-30-18
REFERENCE NUMBER
INS-2264-02
Standard Installation Instructions
TECHNOLOGY
with TECHNOLOGY
& Low Voltage
PROJECT:
TYPE:
SIGN STAR™ & TWIN SIGN STAR™
UPM™ SURFACE MOUNT
10. Connect secondary leads from transformer
to fixture leads using pre-wired factory quick
disconnect.
GroundHotNeutral
LAMP
BLUE
WHITE
GROUND
QUICK DISCONNECT
LINE (BLACK)
NEUTRAL (WHITE)
GROUND (GREEN)
BARE WIRE
IN UPM
RED
BLACK
BLUE
WHITE
GREEN
BALLAST
11. Make sure UPM housing gasket is free of any dirt
or debris. Attach the faceplate by tightening the
(4) #6-32 captive screws evenly using a 5/64”
Allen wrench.
12. Use 5/32” Allen wrench to loosen #10-32
stainless steel black oxide socket head cap screw
at the knuckle. Aim fixture to desired vertical
location. Tighten to secure aiming position.
13. Optional 360SL™: Use 5/64” Allen wrench to
loosen stainless steel set screw on the 360SL™
rotational mounting system and rotate to
desired horizontal location. Tighten to secure
aiming position.
Sign Star™ Style D (SN-D) shade must be
installed facing downwards.
RELEASED
8-15-18
REFERENCE NUMBER
INS000004
40429 Brickyard Drive • Madera, CA 93636 • USA
559.438.5800 • FAX 559.438.5900
www.bklighting.com • [email protected]
B-K LIGHTING
IMPORTANT SAFETY INFORMATION LISTED ON REVERSE
READ, FOLLOW, AND SAVE ALL SAFETY AND INSTALLATION INSTRUCTIONS
THIS DOCUMENT CONTAINS PROPRIETARY INFORMATION OF B-K LIGHTING, INC. AND ITS RECEIPT OR POSSESSION DOES NOT CONVEY ANY RIGHTS TO REPRODUCE, DISCLOSE ITS CONTENTS, OR TO MANUFACTURE, USE OR SELL ANYTHING
IT MAY DESCRIBE. REPRODUCTION, DISCLOSURE OR USE WITHOUT SPECIFIC WRITTEN AUTHORIZATION OF B-K LIGHTING, INC. IS STRICTLY FORBIDDEN.
LED & LOW VOLTAGE HALOGEN
2-1/4” Size
REPLACING LED BOARD/DRIVER AND OPTICS
1. Use 5/64” Allen wrench to loosen #8-32 stainless
set screw and remove cap.
4. Disengage LED board and driver assembly.
Replace with new board and driver assembly.
5. Reverse install LED board and driver.
6. With flat head screw driver rotate dial to desired
lumen output. Replace cap.
2. Space three fingers evenly around the optic
and gently rock optic to remove.
3. Use 5/64” Allen wrench to remove two (2)
#2-56 socket head cap screws on LED board,
grasp LED board and gently pull up to expose
quick disconnect.
TO CHANGE LUMEN OUTPUT (WHEN REQUIRED)
1. Use 5/64” Allen wrench to loosen #8-32 stainless
set screw and remove cap.
3. Place cap on fixture and tighten set screw.
Tighten screw to 1/2 inch pounds. Top of screw
should sit flush with fixture cap.
2. With flat head screw driver rotate dial to
desired lumen output.
This product is available with Adjust-e-Lume® (Patent Pend.) for DynamicLLumen Output Control
Warning! The light output of this product may be dynamically adjusted as desired to raise and lower light levels. Please ensure the xture is set
to the appropriate light level desired during installation.
Warning: Do not over tighten set screw.
Doing so will compromise O Ring seal and
will void warranty.
TECHNOLOGY
with
TECHNOLOGY
LAMP INSTALLATION OR RELAMPING IF REQUIRED FOR LOW VOLTAGE HALOGEN LAMPS
1. Use 5/64” Allen wrench to loosen #8-32
stainless set screw and remove cap.
3. Place cap on fixture and tighten set screw.
Tighten screw to 1/2 in-lbs. Top of screw
should sit flush with fixture cap.
Warning: Do not over tighten set screw.
Doing so will compromise O Ring seal and
will void warranty.
2. Firmly insert lamp pins into socket to make
connection. Rocking motion may be required.
Do not exceed the maximum wattage listed
on the fixture label before installing.
Replacement Instructions
RELEASED
8-17-18
REFERENCE NUMBER
INS-2164-00
40429 Brickyard Drive • Madera, CA 93636 • USA
559.438.5800 • FAX 559.438.5900
www.bklighting.com • [email protected]
B-K LIGHTING
THIS DOCUMENT CONTAINS PROPRIETARY INFORMATION OF B-K LIGHTING, INC. AND ITS RECEIPT OR POSSESSION DOES NOT CONVEY ANY RIGHTS TO REPRODUCE, DISCLOSE ITS CONTENTS, OR TO MANUFACTURE, USE OR SELL ANYTHING IT MAY
DESCRIBE. REPRODUCTION, DISCLOSURE OR USE WITHOUT SPECIFIC WRITTEN AUTHORIZATION OF B-K LIGHTING, INC. IS STRICTLY FORBIDDEN.
IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE THESE INSTALLATION INSTRUCTIONS
Warning Hot Surface
TOOLS
NEEDED:
By Others
5/32” & 5/64”Allen Wrench
L.O.C.K.™ Knuckle System
Standard Adjustment
• Product must be installed by a qualified person in a manner
consistent with its intended use and in compliance with the
National Electrical Code, Canadian Electrical Code, and all Local
and Provincial Codes.
• Follow product label information and instructions.
• Qualified Personnel must perform all servicing or relamping of
this product.
• Before wiring to power supply and during servicing or relamping,
turn off power at fuse or circuit breaker before service.
• The use of accessory equipment not recommended by the
manufacturer or installed contrary to instructions may cause an
unsafe condition. The use of damaged components may cause
an unsafe condition and void product warranty.
IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE ALL SAFETY
AND INSTALLATION INSTRUCTIONS
• Do not block light emanating from product in whole or part,
as this may cause an unsafe condition.
• Never operate the fixture with missing or damaged lens.
Lens must be cleaned on regular basis.
• Entire fixture may become extremely hot. Do not touch hot
lens or fixture body. Do not touch the lamp at any time. Use
a clean, dry, soft cloth to handle the lamp. Oil from skin may
damage the lamp and cause it to rupture.
• Replace lamp only with correct wattage and type of lamp
marked on fixture label.
• All gaskets, O-rings and sealing surfaces must be kept clean
during installation and service; failure to do this may cause an
unsafe condition and void product warranty.
INSTRUCTIONS PERTAINING TO
A RISK OF FIRE, OR INJURY TO
PERSONS IMPORTANT SAFETY
INSTRUCTIONS
Lighted lamp is HOT!
WARNING - To reduce the risk of FIRE OR INJURY TO PERSONS:
Turn off/unplug and allow to cool before replacing lamp.
Lamp gets HOT quickly! Contact only switch/plug when
turning on.
Do not touch hot lens, guard, or enclosure (see diagram/
picture).
Keep lamp away from materials that may burn.
Do no touch the lamp at any time. Use a soft cloth. Oil
from skin may damage lamp.
Do not operate the luminaire fitting with a missing or
damaged shield.
SAVE THESE INSTRUCTIONS
· Suitable for wet locations · Additionally suitable for mounting within 4 ft. of the ground
IMPORTANT LISTINGS AND CERTIFICATIONS
L.O.C.K.™ Knuckle - (Locking ‘O’ Ring Compression Knuckle)
2. Aim fixture to desired angle.1. Use 5/32” Allen wrench to slightly loosen #10-32
stainless steel set screw on the stem for 180° aiming
purpose.
3. Tighten #10-32 stainless steel set screw using a 5/32”
Allen wrench to secure aiming position.
Warning: Do not over tighten set screw. Doing
so will compromise O-ring seal and will void
warranty.
4. To adjust stem horizontally, loosen two (2) #8-32
screws at base of stem cap using 5/64” Allen
wrench. Adjust as needed, then secure.
5. To adjust stem, loosen #8-32 screw with 5/64” Allen
wrench at stem cap. Adjust as needed, then secure.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9

B-K lighting Twin Delta Star - MR16 Installation guide

Brand
B-K lighting
Model
Twin Delta Star - MR16
Type
Installation guide

B-K Lighting Twin Delta Star - MR16

The B-K Lighting Twin Delta Star - MR16 is a versatile and powerful lighting fixture designed for a wide range of indoor and outdoor applications. With its sleek design and advanced features, the Twin Delta Star - MR16 offers exceptional illumination and energy efficiency.

Key Features:

  • Adjustable Beam Angle: Customize the beam angle from a narrow 15 degrees to a wide 60 degrees, providing precise control over light distribution.
  • Interchangeable Optics: Easily switch between different optic lenses (sold separately) to achieve the desired beam pattern and light effect.
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents