luminii Leto 12 Installation guide

luminii
Brand
luminii
Model
Leto 12
Type
Installation guide

The luminii Leto 12 is a versatile LED fixture suitable for dry indoor locations. It features a slim profile and easy installation with seismic tethers for added safety. The Leto 12 provides ample illumination while allowing air to flow freely around the fixture. Enjoy energy savings and a long lifespan with this high-quality luminaire, perfect for various indoor applications.

The luminii Leto 12 is a versatile LED fixture suitable for dry indoor locations. It features a slim profile and easy installation with seismic tethers for added safety. The Leto 12 provides ample illumination while allowing air to flow freely around the fixture. Enjoy energy savings and a long lifespan with this high-quality luminaire, perfect for various indoor applications.

rev. 2013|04
302 50 Ave SE, Calgary, Alberta T2G 2A9
www.sensolighting.com
info@sensolighting.com
T 403.216.7043
F 403.216.7045
SENSO
INSTALLATION:
GUIDE
LETO 12
see reverse for template
voir au verso pour gabarit
INSTALLATION: GUIDE
A
B
C
D
E
cut a hole according to dimension
connect the driver to the line voltage and
ground to enclosure
install the springs
plug the fixture to the driver (2x)
secure the fixture with the seismic tether
flip the two (2) retension springs upward
push the fixture in place
3” (76mm)
MINIMUM
8” (200mm)
D
click!
1
2
C
E
4-3/4”
(120mm) 4-3/4”
(120mm)
A B
read and follow these instructions
before installing or maintaining this
product
• this product is suitable for
DRY INDOOR LOCATIONS ONLY
• make sure this product is NOT on the same circuit as
inductive loads, (e.g. fluorescent bulbs, discharge bulbs,
ventilation fans, etc...)
• allow air to flow freely around the fixture
• do not install insulation within 3” (76 mm) of the
fixture
• ceiling thickness must be between 1/8” &1”(3mm &
25mm)
• Do not switch on line voltage until all wiring is complete
• Incorrect wiring will result in irreparable damage to
LED and power supply
• This product should only be installed by a licensed
electrician
WARRANTY
• This product must be installed in accordance with all
applicable installation codes and ordinance
• Limited two (2) years warranty
• Warranty is void in the eventuality of unauthorized
modifications and/or improper use
A
B
C
D
E
découper un trou selon les dimensions données
relier l’alimentation du DEL au secteur et le fil de
mise à la terre au boîtier
installer les ressorts
brancher le luminaire à l’alimentation (2X)
fixer le cable de sécurité au luminaire
replier les deux (2) ressorts vers le haut et
insérer le luminaire en place
veuillez lire et suivre ces
instructions avant l’installation ou
l’entretien de ce produit
• Ce produit convient pour une installation à
L’INTÉRIEUR DANS UN ENVIRONNEMENT
SEC SEULEMENT
• Assurer vous que des charges inductives ne se retrouvent
pas sur le même circuit que ce produit, (i.e. fluorescent,
ampoules à décharge, ventilateurs, etc...)
• Permettre à l’air de circuler librement autour du luminaire
• Ne pas installer d’isolant à moins de 3” (76mm) du
luminaire
• L’épaisseur du plafond doit être comprise entre 1/8” & 1”
( 3mm & 25mm)
• Compléter les branchements avant de mettre sous tension
• Un branchement incorrect créerait des dommages
irréparables à l’alimentation et au DEL
• Ce produit devrait être uniquement installé par un
électricien qualifié
mettre le courant hors tension
GARANTIE
• Ce produit doit être installé conformément au code
d’installation et autres normes applicables
• Garantie limitée de deux (2) ans
• La garantie est non valide advenant une modification
non autorisée ou un usage non approprié
switch off the line voltage supply
click!
254752
rev. 2013|04
www.sensolighting.com
info@sensolighting.com
T 403.216.7043
F 403.216.7045
Actual required cut out
(DO NOT SCALE)
Installation template for
LETO 1, LETO 2, LETO 9, LETO 12
4-3/4” (120 mm)
4-3/4” (120 mm)
302 50 Ave SE, Calgary, Alberta T2G 2A9
SENSO
  • Page 1 1
  • Page 2 2

luminii Leto 12 Installation guide

luminii
Brand
luminii
Model
Leto 12
Type
Installation guide

The luminii Leto 12 is a versatile LED fixture suitable for dry indoor locations. It features a slim profile and easy installation with seismic tethers for added safety. The Leto 12 provides ample illumination while allowing air to flow freely around the fixture. Enjoy energy savings and a long lifespan with this high-quality luminaire, perfect for various indoor applications.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages

Related papers

Other documents