Wallenstein BXMT Series Setup Instructions

Type
Setup Instructions

Wallenstein BXMT Series is an efficient tool for shredding wood. It has a variety of features that make it a great choice for homeowners and professionals alike. The BXMT Series is powered by a Kohler Command engine that provides ample power for the chipping head. The chipping head is made of high-quality steel and is designed to last. The BXMT Series also features a large hopper that can accommodate branches up to 3 inches in diameter. The hopper is also equipped with a safety chain to prevent accidents. The BXMT Series is a versatile machine that can be used for a variety of tasks.

Wallenstein BXMT Series is an efficient tool for shredding wood. It has a variety of features that make it a great choice for homeowners and professionals alike. The BXMT Series is powered by a Kohler Command engine that provides ample power for the chipping head. The chipping head is made of high-quality steel and is designed to last. The BXMT Series also features a large hopper that can accommodate branches up to 3 inches in diameter. The hopper is also equipped with a safety chain to prevent accidents. The BXMT Series is a versatile machine that can be used for a variety of tasks.

Set-up Instructions
Rev Feb-2019 Part Number: Z97027_SI
BXMT3209
BXMT3213
BXMT4224
Always Put Safety First!
Read these assembly instructions thoroughly before
beginning. Make sure each step is understood before
attempting it. Be familiar with all safety signs on the
machine and their meaning.
Tighten all fasteners to the torque value specied on
the last page. Recheck before using the machine.
WARNING!
Position the crate in a large open area to allow
access from all sides during assembly.
Stay clear of overhead power lines and obstructions
when lifting the machine during assembly. Contact
with power lines can cause electrocution. Contact
with obstructions can damage components or cause
them to fail.
Keep the assembly area clean to prevent slipping or
tripping.
Use a hoist when lifting components that weigh 50 lb
(23 kg) or more to avoid back injury.
All lifting devices (straps, slings, chains, ratchet
blocks) must comply with applicable local
regulations and certications. Wallenstein Equipment
Inc. cannot accept responsibility for the use of
sub-standard equipment and work practices.
Use lifting equipment with a capacity greater than the
weight of the component. Place jack stands or wood
blocking under the machine to securely stabilize it
before working on it during assembly.
Use the correct tool for the job. Repair or replace
broken or defective equipment or tools. Makeshift
tools can create safety hazards. A tool that breaks or
slips during use risks personal injury.
WARNING!
Avoid the risk of personal injury or machine damage!
Read the operator’s manual before using this
equipment. Carefully read all safety messages in the
manual and follow all safety signs on the machine.
IMPORTANT! Inspect for damage from shipping.
Immediately contact the shipping company if damage
is found.
Note: Some parts are attached to skid with screws.
Shipping brackets are not reused.
Assembly hardware is located inside operator's manual
tube.
BXMT3209BXMT3213BXMT4224
BXMT3209
BXMT3213
BXMT4224
i
1
2
BXMT3209
A
B
C
D
E
F
3
2X
2X
2X
BXMT3209
4
C
5
C
BXMT3209
6
2X
4X
B
7
A
BXMT3209
8
4X
E
9
2X 6X
F
10
BXMT3209
4X
D
1
2
BXMT3213
A
B
C
D
G
E
C
F
3
4X
1X
1X
4
BXMT3213
5
6X
F
6
BXMT3213
6X
G
7
4X
lbf•ft
N•m
50–60
65–78
C
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80

Wallenstein BXMT Series Setup Instructions

Type
Setup Instructions

Wallenstein BXMT Series is an efficient tool for shredding wood. It has a variety of features that make it a great choice for homeowners and professionals alike. The BXMT Series is powered by a Kohler Command engine that provides ample power for the chipping head. The chipping head is made of high-quality steel and is designed to last. The BXMT Series also features a large hopper that can accommodate branches up to 3 inches in diameter. The hopper is also equipped with a safety chain to prevent accidents. The BXMT Series is a versatile machine that can be used for a variety of tasks.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages