South bend SB1122 Owner's manual

Brand: South bend

Model: SB1122

Type: Owner's manual

A Tradition of Excellence

South Bend Tools

MODEL SB1122

9" X 12" 2 HP METAL-CUTTING BANDSAW

OWNER'S MANUAL

***Keep for Future Reference***

Customer Service

We stand behind our machines. If you have any service questions, parts requests or general questions

about your purchase, feel free to contact us.

South Bend Tools

P.O. Box 2027

Bellingham, WA 98227

Phone: (360) 734-1540

Fax: (360) 676-1075 (International)

Fax: (360) 734-1639 (USA Only)

Email: [email protected]

Updates

For your convenience, any updates to this manual will be available to download free of charge

through our website at:

www.southbendtools.com

Scope of Manual

This manual helps the reader understand the machine, how to prepare it for operation, how to control

it during operation, and how to keep it in good working condition. We assume the reader has a basic

understanding of how to operate this type of machine, but that the reader is not familiar with the

controls and adjustments of this specific model. As with all machinery of this nature, learning the

nuances of operation is a process that happens through training and experience. If you are not an

experienced operator of this type of machinery, read through this entire manual, then learn more

from an experienced operator, schooling, or research before attempting operations. Following this

advice will help you avoid serious personal injury and get the best results from your work.

Manual Feedback

We've made every effort to be accurate when documenting this machine. However, errors sometimes

happen or the machine design changes after the documentation process—so

the manual may not

exactly match your machine.

If a difference between the manual and machine leaves you in doubt,

contact our

customer service for clarification.

We highly value customer feedback on our manuals. If you have a moment, please share your

experience using this manual. What did you like about it? Is there anything you would change to

make it better? Did it meet your expectations for clarity, professionalism, and ease-of-use?

South Bend Tools

/O Technical Documentation Manager

P.O. Box 2027

Bellingham, WA 98227

Email: [email protected]

Table of Contents

MAINTENANCE .............................................................40

Maintenance Schedule .......................................40

Cleaning .............................................................40

Lubrication .........................................................40

Machine Storage ................................................ 42

Hydraulic System Maintenance ........................ 43

Cutting Fluid System Maintenance ..................46

SERVICE...........................................................................48

Adjusting Headstock Travel Limits ..................48

Squaring Blade to Table .................................... 50

Adjusting Blade Guides & Bearings ................. 51

Replacing Motor Brushes ..................................54

Adjusting Downfeed Pressure ........................... 54

Calibrating Headstock Angle Scale ..................55

Adjusting Angle Stops ....................................... 55

Adjusting Workpiece Contact Safety Switch ....57

Adjusting Vise Gib .............................................58

Adjusting Blade Brush ...................................... 58

TROUBLESHOOTING .................................................59

ELECTRICAL ................................................................... 63

Electrical Safety Instructions ...........................63

Electrical Overview ............................................64

Control Box Bottom Panel Wiring Diagram ..... 65

Control Box Bottom Panel .................................66

Control Box Rear Panel Wiring Diagram .........67

Control Box Rear Panel ..................................... 68

Control Panel Wiring Diagram ......................... 69

Control Panel .....................................................70

Motor Wiring Diagrams.....................................71

Electrical Component Wiring Diagrams ..........72

HYDRAULICS ................................................................. 73

Hydraulic System Diagram ...............................73

PARTS................................................................................ 74

Headstock ........................................................... 74

Base ....................................................................77

Control Panel Electrical Components ...............80

Control Box Electrical Components (Bottom) ..81

Control Box Electrical Components (Rear) ......82

Machine Labels (Front) ..................................... 83

Machine Labels (Rear) ....................................... 84

WARRANTY ..................................................................... 85

INTRODUCTION ...............................................................2

Identiﬁcation ........................................................2

Description of Controls & Components ..............3

Product Speciﬁcations .........................................5

SAFETY ................................................................................7

Understanding Risks of Machinery .................... 7

Basic Machine Safety ..........................................7

Additional Horizontal Metal Bandsaw Safety ... 9

Additional Hydraulic System Safety ................10

PREPARATION .............................................................. 11

Preparation Overview ........................................11

Required for Setup .............................................11

Power Supply Requirements ............................. 12

Unpacking ..........................................................14

Inventory ............................................................ 14

Cleaning & Protecting .......................................14

Location .............................................................. 15

Assembly ............................................................ 16

Initial Lubrication .............................................17

Test Run .............................................................18

Inspections & Adjustments ...............................21

OPERATION .................................................................... 22

Operation Overview ........................................... 22

Disabling Switches.............................................23

Operation Tips ...................................................23

Workpiece Inspection .........................................24

Selecting Blades .................................................24

Blade Breakage .................................................. 26

Blade Care & Break-In ......................................26

Setting Downfeed Rate ......................................27

Changing Blade Speed .......................................27

Blade Speed Chart .............................................28

Chip Inspection Chart ....................................... 28

Changing Blade ..................................................29

Tensioning Blade ...............................................31

Adjusting Blade Guides .....................................32

Manual & Automatic Controls .......................... 32

Angled Cuts ........................................................ 34

Opening & Closing Vise ..................................... 36

Adjusting Work Stop..........................................37

Using Cutting Fluid System .............................37

ACCESSORIES .............................................................. 39

-2-

For Machines Mfd. Since 10/22

South Bend Tools

Model SB1122 INTRODUCTION

Vise Handwheel

Work Stop

Control Panel

Blade

Blade Cover

Blade Tension

Handwheel

w/Gauge

Headstock

Handle

Angle Lock

Handle

Power Switch

0° Flip

Stop

Cutting Fluid

Valve (1 of 2)

Vise Position

Lock Handle

Vise Quick-

Release Handle

Movable

Vise Jaw

Fixed Vise Jaw

(1 of 2)

Downfeed

Rate Dial

For Your Own Safety Read Instruction Manual Before Operating Saw

a) Wear eye protection and respirator.

b) Do not remove jammed cutoff pieces until blade has stopped.

c) Maintain proper adjustment of blade tension, blade guides, and thrust bearings.

d) Adjust upper guide to just clear workpiece.

e) Properly support and secure workpiece with table, vise, or some type of support ﬁ xture. Never

hold workpiece with hands during cut.

Identiﬁ cation

Circuit

Breaker

Reset

Button

INTRODUCTION

South Bend Tools

For Machines Mfd. Since 10/22 Model SB1122

-3-

INTRODUCTION

Description of Controls

& Components

Control Panel

Refer to Figures 1–5 and the following

descriptions to become familiar with the basic

controls and components used to operate this

machine.

A. POWER Lamp: Illuminates when machine

is connected to power and power switch is in

ON (1) position.

B. Man/Auto Key Switch / : Switches

between manual or automatic operation

mode when key is inserted.

C. HYD ON Button : Turns hydraulic pump

ON.

D. AUTO CUTTING Button : When in Auto

mode, starts automatic cutting cycle: vise

closes, blade starts, headstock lowers so

blade can cut into workpiece, blade stops,

headstock rises, and vise opens (if vise

switch is in OPEN position). When in

manual mode, enables blade start.

E. Manual ON Button I : Starts blade and

cutting fluid pump when machine is

in manual operation mode and AUTO

CUTTING button has been pressed.

F. OFF Button O : Stops blade, hydraulic

pump, and cutting fluid pump.

G. OVERLOAD Lamp: Illuminates when a motor

has overloaded and shut down, or downfeed

limit switch is engaged.

H. EMERGENCY STOP Button: Stops all

machine functions and prevents machine

from starting until reset. Twist clockwise to

reset.

I. Blade Speed Dial: Adjusts blade speed

from 85–265 FPM. Rotate dial clockwise

to increase speed or counterclockwise to

decrease speed.

J. Vise Switch / : Hydraulically clamps

and unclamps workpiece.

K. SAW BOW Switch / : Raises and

lowers headstock.

L. Downfeed Rate Dial: Controls rate at

which headstock lowers once workpiece is

contacted and blade feeds into workpiece.

Turn counterclockwise to increase rate; turn

clockwise to decrease.

Figure 1. Control panel front.

C D E

IJK

M. Power Switch: Turns incoming power ON (1)

and OFF (0).

N. Circuit Breaker Reset Button: Allows

machine to be restarted after thermal

overload protection has tripped. To reset,

turn power switch to OFF (0) position, wait

a few minutes for machine to cool, then

press reset button. If button does not stay

depressed, allow motor to cool longer, then

try again.

Figure 2. Control panel rear.

-4-

For Machines Mfd. Since 10/22

South Bend Tools

Model SB1122 INTRODUCTION

Headstock

X. Blade Tension Handwheel w/Gauge:

Increases and decreases blade tension.

Gauge indicates blade tension measured in

PSI.

Y. Headstock Handle: Adjusts headstock and

vise table angle when angle lock components

are released.

Z. Top Blade Guide Lock Handle: Loosens

to adjust blade guide position; tightens to

secure.

AA. Top Blade Guide: Supports blade. Adjust top

blade guide as close to workpiece as possible

to prevent blade from twisting.

AB. Cutting Fluid Valve (1 of 2): Controls flow of

cutting fluid onto blade.

AC. Workpiece Arm: Slows headstock lowering

rate to match downfeed rate once workpiece

is contacted.

AD. Blade Cover: Protects operator from blade,

and provides access for blade and wheel

maintenance.

Figure 5. Headstock controls and components.

O. Vise Handwheel: Closes and opens vise to

clamp workpiece.

P. Movable Vise Jaw: Secures workpiece against

fixed vise jaw during cutting operation.

Jaw is positioned manually and locked

hydraulically.

Q. Fixed Vise Jaws: Help hold workpiece during

cutting operations.

R. 0° Flip Stop: Flips up to quickly adjust

vise table and headstock angle to 0° when

headstock is adjusted between 0°–60° to the

right.

S. Work Stop: Adjusts for repetitive cutting

operations.

T. Angle Lock Handle: Loosens to adjust vise

table and headstock angle; tightens to secure

angle setting.

U. Vise Table: Rotates left 45° and right 60°

with headstock for angled cuts.

V. Vise Quick-Release Handle: Tightens

to release vise leadscrew so vise can be

adjusted open or closed quickly without vise

handwheel; loosens to engage vise leadscrew

and activate vise handwheel.

W. Vise Position Lock Handle: Loosens to allow

vise position adjustment along vise track;

tightens to secure position.

Vise Table

Figure 4. Rear vise controls and components.

Figure 3. Front vise controls and components.

South Bend Tools

For Machines Mfd. Since 10/22 Model SB1122

-5-

INTRODUCTION

Model SB1122 Page 1 of 3

Model SB1122

9" x 12" 2 HP MetalCutting Bandsaw

Product Dimensions

Weight............................................................................................................................................................. 965 lbs.

Width (side-to-side) x Depth (front-to-back) x Height..................................................................... 58 x 30 x 79 in.

Footprint (Length x Width)....................................................................................................................... 34 x 27 in.

Space Required for Full Range of Movement (Width x Depth)......................................................... 68-1/2 x 36 in.

Shipping Dimensions

Type.................................................................................................................................................. Wood Slat Crate

Content.......................................................................................................................................................... Machine

Weight........................................................................................................................................................... 1032 lbs.

Length x Width x Height................................................................................................................... 32 x 56 x 68 in.

Must Ship Upright................................................................................................................................................ Yes

Electrical

Power Requirement......................................................................................................... 220V, Single-Phase, 60 Hz

Full-Load Current Rating.................................................................................................................................... 10A

Minimum Circuit Size.......................................................................................................................................... 15A

Connection Type..................................................................................................................................... Cord & Plug

Power Cord Included............................................................................................................................................. Yes

Power Cord Length.......................................................................................................................................... 100 in.

Power Cord Gauge......................................................................................................................................... 14 AWG

Plug Included........................................................................................................................................................ Yes

Included Plug Type.............................................................................................................................................. 6-15

Switch Type....................................................................................... Control Panel w/Magnetic Switch Protection

Motors

Main

Horsepower............................................................................................................................................... 2 HP

Phase............................................................................................................................................ Single-Phase

Amps............................................................................................................................................................. 5A

Speed................................................................................................................................................ 3600 RPM

Type................................................................................................................................................... DC Brush

Power Transfer ............................................................................................................................. Worm Gear

Bearings................................................................................................ Shielded & Permanently Lubricated

Hydraulic Pump

Horsepower............................................................................................................................................ 1/2 HP

Phase............................................................................................................................................ Single-Phase

Amps.......................................................................................................................................................... 4.7A

Speed................................................................................................................................................ 1720 RPM

Type........................................................................................................................ Capacitor-Start Induction

Power Transfer ...................................................................................................................................... Direct

Bearings................................................................................................ Shielded & Permanently Lubricated

Centrifugal Switch/Contacts Type..................................................................................................... Internal

Product Specifications

P.O. Box 2027, Bellingham, WA 98227 U.S.A.

www.southbendtools.com

PHONE: (360) 734-1540 • © South Bend Tools

-6-

For Machines Mfd. Since 10/22

South Bend Tools

Model SB1122 INTRODUCTION

Model SB1122 Page 2 of 3

utting luid Pump

Horsepower............................................................................................................................................ 1/8 HP

Phase............................................................................................................................................ Single-Phase

Amps.......................................................................................................................................................... 0.3A

Speed................................................................................................................................................ 3440 RPM

Type......................................................................................................................................................... TFC

Power Transfer ...................................................................................................................................... Direct

Bearings................................................................................................ Shielded & Permanently Lubricated

Main Specifications

peration nfo

Blade Speeds............................................................................................................................... 85 - 265 FPM

Std. Blade Length............................................................................................................................ 108-1/4 in.

Std. Blade Width............................................................................................................................... 1-1/16 in.

Head Swivel................................................................................................................... Left 45, Right 60 deg.

utting apacities

Cutting Height........................................................................................................................................... 9 in.

Angle Cuts..................................................................................................................... Left 45, Right 60 deg.

Vise aw Depth.................................................................................................................................. 12-5/8 in.

Vise aw Height................................................................................................................................... 5-1/2 in.

Max. Capacity Rectangular Height at 90 Deg......................................................................................... 9 in.

Max. Capacity Rectangular Width at 90 Deg......................................................................................... 12 in.

Max. Capacity Round at 90 Deg............................................................................................................. 10 in.

Max. Capacity Rectangular Height at 30 Deg................................................................................... 8-1/4 in.

Max. Capacity Rectangular Width at 30 Deg.................................................................................. 10-5/8 in.

Max. Capacity Round at 30 Deg......................................................................................................... 8-5/8 in.

Max. Capacity Rectangular Height at 45 Deg......................................................................................... 7 in.

Max. Capacity Rectangular Width at 45 Deg........................................................................................... 7 in.

Max. Capacity Round at 45 Deg......................................................................................................... 7-7/8 in.

Max. Capacity Rectangular Height at 60 Deg................................................................................... 6-1/8 in.

Max. Capacity Rectangular Width at 60 Deg.................................................................................... 4-1/2 in.

Max. Capacity Round at 60 Deg......................................................................................................... 4-1/2 in.

Max. Capacity Rectangular Height at -45 Deg........................................................................................ 7 in.

Max. Capacity Rectangular Width at -45 Deg................................................................................... 6-3/4 in.

Max. Capacity Round at -45 Deg........................................................................................................ 6-3/4 in.

onstruction

Table.................................................................................................................... Precision-Ground Cast Iron

Upper Wheel...................................................................................................................................... Cast Iron

Lower Wheel...................................................................................................................................... Cast Iron

Body................................................................................................................................................... Cast Iron

Base.................................................................................................................................................... Cast Iron

Stand......................................................................................................................................................... Steel

Wheel Cover.............................................................................................................................................. Steel

Paint Type/Finish................................................................................................................................. namel

ther

Wheel Size........................................................................................................................................ 12-9/16 in.

Blade Guides...................................................................................................... Carbide Steel, Ball Bearings

Coolant Capacity................................................................................................................................... 3.9 gal.

Hydraulic Capacity.................................................................................................................................. 2 gal.

ale nfo

Floor To Cutting Area Height........................................................................................................... 38-1/2 in.

South Bend Tools

For Machines Mfd. Since 10/22 Model SB1122

-7-

SAFETY

Understanding Risks of Machinery

Operating all machinery and machining equipment can be dangerous or relatively safe depending

on how it is installed and maintained, and the operator's experience, common sense, risk awareness,

working conditions, and use of personal protective equipment (safety glasses, respirators, etc.).

The owner of this machinery or equipment is ultimately responsible for its safe use. This

responsibility includes proper installation in a safe environment, personnel training and usage

authorization, regular inspection and maintenance, manual availability and comprehension,

application of safety devices, integrity of cutting tools or accessories, and the usage of approved

personal protective equipment by all operators and bystanders.

The manufacturer of this machinery or equipment will not be held liable for injury or property

damage from negligence, improper training, machine modiﬁ cations, or misuse. Failure to read,

understand, and follow the manual and safety labels may result in serious personal injury, including

amputation, broken bones, electrocution, or death.

The signals used in this manual to identify hazard levels are as follows:

Death or catastrophic

harm WILL occur.

Moderate injury or ﬁ re

MAY occur.

Death or catastrophic

harm COULD occur.

Machine or property

damage may occur.

Basic Machine Safety

Owner’s Manual: All machinery and machining

equipment presents serious injury hazards

to untrained users. To reduce the risk of

injury, anyone who uses THIS item MUST

read and understand this entire manual

before starting.

Personal Protective Equipment: Operating or

servicing this item may expose the user

to ﬂ ying debris, dust, smoke, dangerous

chemicals, or loud noises. These hazards

can result in eye injury, blindness, long-

term respiratory damage, poisoning,

cancer, reproductive harm or hearing loss.

Reduce your risks from these hazards

by wearing approved eye protection,

respirator, gloves, or hearing protection.

Trained/Supervised Operators Only: Untrained

users can seriously injure themselves

or bystanders. Only allow trained and

properly supervised personnel to operate

this item. Make sure safe operation

instructions are clearly understood. If

electrically powered, use padlocks and

master switches, and remove start switch

keys to prevent unauthorized use or

accidental starting.

Guards/Covers: Accidental contact with

moving parts during operation may cause

severe entanglement, impact, cutting,

or crushing injuries. Reduce this risk by

keeping any included guards/covers/doors

installed, fully functional, and positioned

for maximum protection.

-8-

For Machines Mfd. Since 10/22

South Bend Tools

Model SB1122 SAFETY

Entanglement: Loose clothing, gloves, neckties,

jewelry or long hair may get caught in

moving parts, causing entanglement,

amputation, crushing, or strangulation.

Reduce this risk by removing/securing

these items so they cannot contact moving

parts.

Mental Alertness: Operating this item with

reduced mental alertness increases the

risk of accidental injury. Do not let a

temporary influence or distraction lead to a

permanent disability! Never operate when

under the influence of drugs/alcohol, when

tired, or otherwise distracted.

Safe Environment: Operating electrically

powered equipment in a wet environment

may result in electrocution; operating near

highly ﬂ ammable materials may result in a

ﬁ re or explosion. Only operate this item in

a dry location that is free from ﬂ ammable

materials.

Electrical Connection: With electrically

powered equipment, improper connections

to the power source may result in

electrocution or fire. Always adhere to all

electrical requirements and applicable

codes when connecting to the power source.

Have all work inspected by a qualified

electrician to minimize risk.

Disconnect Power: Adjusting or servicing

electrically powered equipment while it

is connected to the power source greatly

increases the risk of injury from accidental

startup. Always disconnect power

BEFORE any service or adjustments,

including changing blades or other tooling.

Secure Workpiece/Tooling: Loose workpieces,

cutting tools, or rotating spindles can

become dangerous projectiles if not

secured or if they hit another object during

operation. Reduce the risk of this hazard

by verifying that all fastening devices are

properly secured and items attached to

spindles have enough clearance to safely

rotate.

Chuck Keys or Adjusting Tools: Tools used to

adjust spindles, chucks, or any moving/

rotating parts will become dangerous

projectiles if left in place when the machine

is started. Reduce this risk by developing

the habit of always removing these tools

immediately after using them.

Work Area: Clutter and dark shadows increase

the risks of accidental injury. Only operate

this item in a clean, non-glaring, and well-

lighted work area.

Properly Functioning Equipment: Poorly

maintained, damaged, or malfunctioning

equipment has higher risks of causing

serious personal injury compared to

those that are properly maintained.

To reduce this risk, always maintain

this item to the highest standards and

promptly repair/service a damaged or

malfunctioning component. Always follow

the maintenance instructions included in

this documentation.

Unattended Operation: Electrically powered

equipment that is left unattended while

running cannot be controlled and is

dangerous to bystanders. Always turn the

power OFF before walking away.

Health Hazards: Certain cutting fluids and

lubricants, or dust/smoke created when

cutting, may contain chemicals known to

the State of California to cause cancer,

respiratory problems, birth defects,

or other reproductive harm. Minimize

exposure to these chemicals by wearing

approved personal protective equipment

and operating in a well ventilated area.

Difﬁ cult Operations: Attempting difficult

operations with which you are unfamiliar

increases the risk of injury. If you

experience difficulties performing the

intended operation, STOP! Seek an

alternative method to accomplish the

same task, ask a qualified expert how the

operation should be performed, or contact

our Technical Support for assistance.

South Bend Tools

For Machines Mfd. Since 10/22 Model SB1122

-9-

SAFETY

Additional Horizontal Metal Bandsaw Safety

Workpiece Handling. Always properly support

workpiece with table, vise, or some type of

support fixture.

Always secure workpiece in vise

before cutting. Never hold the workpiece with

your hands during a cut.

Unstable Workpieces. Avoid cutting workpieces

that cannot be properly supported or clamped

in a vise or jig, because they can unexpectedly

move while cutting and draw the operator’s

hands into the blade causing serious personal

injury. Examples are chains, cables, round

or oblong-shaped workpieces, and those with

internal or built-in moving or rotating parts, etc.

Fire Hazard. Use EXTREME CAUTION if cutting

magnesium. Using the wrong cutting fluid could

lead to chip fire and possible explosion.

Cutting Fluid Safety.

Cutting fluids are poisonous.

Always follow manufacturer’s cutting-fluid

safety instructions. Pay particular attention

to contact, contamination, inhalation,

storage and disposal warnings. Spilled

cutting fluid invites slipping hazards.

Blade Condition. Do not operate with dull,

cracked, or badly worn blade. Inspect blades

for cracks and missing teeth before each use.

Hand Placement. Never position hands or fingers

in line with the cut or under bandsaw

headstock while lowering or operating.

Hands could be cut or crushed.

Blade Guard Position. Adjust blade guard as

close to workpiece as possible before cutting to

minimize operator exposure to unused portion

of blade.

Entanglement Hazards. Do not operate this saw

without blade guard in place. Loose clothing,

jewelry, long hair and work gloves can be drawn

into working parts.

Blade Replacement. When replacing blades,

disconnect the machine from power, wear gloves

to protect hands and safety glasses to protect

eyes.

Hot Surfaces. Contact with hot surfaces from

machine components, ejections of hot chips,

swarf, and the workpiece itself can cause

burns.

Serious injury or death can occur from getting ﬁ ngers, hair, or clothing entangled in rotating or

moving parts or making direct contact with the moving blade. To minimize risk of injury, anyone

operating this machine MUST completely heed hazards and warnings below.

Like all machinery, there is potential danger

when operating this machine. Accidents are

frequently caused by lack of familiarity or

failure to pay attention. Use this machine with

respect and caution to decrease the risk of

operator injury. If normal safety precautions

are overlooked or ignored, serious personal

injury may occur.

No list of safety guidelines can be complete.

Every shop environment is different. Always

consider safety first, as it applies to your

individual working conditions. Use this and

other machinery with caution and respect.

Failure to do so could result in serious

personal injury, damage to equipment, or poor

work results.

-10-

For Machines Mfd. Since 10/22

South Bend Tools

Model SB1122 SAFETY

Additional Hydraulic System Safety

Do Not Operate with Leaks. Immediately stop

machine and depressurize hydraulic system

if a leak is discovered or suspected. Operating

hydraulic system with leaks may increase

the hazard of the situation and damage the

machine.

Component Replacement. Only use high-pressure

hydraulic hose and steel hydraulic fittings with

compatible threads when replacing components

in the hydraulic system. DO NOT overtighten

or use soft metal fittings such as brass or

aluminum.

Depressurize for Maintenance. Always

depressurize hydraulic system before

performing any service or maintenance. Always

stop machine and disconnect power before

relieving hydraulic pressure. Verify hydraulic

pressure is at 0 PSI before proceeding with

maintenance.

Preventing Leaks. Always support and restrain

hydraulic hoses to minimize friction during

operation that could lead to machine damage

that may result in serious injury. Regularly

inspect and perform maintenance on the

hydraulic system. Following a regular schedule

will decrease the likelihood of damage to the

machine and reduce the risk of associated

hazards.

Injection Injuries. Immediately seek medical

attention if injection injury occurs. Leaking

hydraulic fluid often has enough pressure to

penetrate skin, which can lead to infection,

amputation, or death. Hydraulic fluid can

enter the skin through small wounds that

are barely noticeable. Minimizing the time

between injury and removal of the injected

material is critical to successful treatment.

Check For Leaks. Never use your hands to check for

hydraulic leaks. Small leaks can be invisible to

the naked eye. Use a piece of wood or cardboard

to find suspected leaks.

Eye Injuries. Safety glasses may not be sufficient

to protect against pressurized hydraulic

fluid. Depressurize hydraulic system before

approaching a known leak.

Fluid Contamination. Make sure hydraulic system

maintenance is performed in a clean and

dust-free work area. Remove all contaminants

from near hydraulic system openings and

components prior to maintenance, to prevent

debris from entering the hydraulic system.

Always use lint-free rags when cleaning

components. Contaminated hydraulic fluid

may damage the machine and cause hydraulic

system failure that can result in serious injury

or death.

Infection, amputation, or death can result from contact with leaking hydraulic ﬂ uid under high

pressure. Additionally, leaking hydraulic ﬂ uid is a serious slip hazard and ﬁ re hazard. To reduce

these risks, anyone operating this machine MUST completely heed the hazards and warnings

below.

South Bend Tools

For Machines Mfd. Since 10/22 Model SB1122

-11-

PREPARATION

Preparation Overview Required for Setup

The items listed below are required to

successfully set up and prepare this machine for

operation.

For Lifting

• A forklift or other power lifting device rated

for the weight of the machine.

• Lifting strap or chain (rated for at least

1300 lbs.)

• Lifting hooks (4)

For Power Connection

• A power source that meets the minimum

circuit requirements for this machine. (Refer

to the Power Supply Requirements

section for details.)

• A qualified electrician to ensure a safe and

code-compliant connection to the power

source.

For Assembly

• Disposable Rags

• Cleaner/Degreaser

• Safety Glasses

• Open-End Wrenches 19mm (2)

• Level

• Hex Wrench 3mm

For Test Run

• Carbon Steel Plate (Between 2"–31⁄2" Thick)

IMPORTANT: Test workpiece for Test Run must

be long enough to be firmly secured in vise.

The purpose of the preparation section is to help

you prepare your machine for operation. The list

below outlines the basic process. Specific steps

for each of these points will be covered in detail

later in this section.

The typical preparation process is as follows:

1. Unpack the machine and inventory the

contents of the box/crate.

2. Clean the machine and its components.

3. Identify an acceptable location for the

machine and move it to that location.

4. Level the machine and either bolt it to the

floor or place it on mounts.

5. Assemble the loose components and make

any necessary adjustments or inspections to

ensure the machine is ready for operation.

6. Connect the machine to the power source.

7. Test run the machine to make sure it

functions properly and is ready for operation.

Incorrect use of this

machine can result in

death or serious injury.

For your own safety, read

and understand this entire

document before using.

Wear safety glasses during

the entire setup process!

Avoid chlorine-based solvents when cleaning

machine, such as acetone or brake parts

cleaner that may damage painted surfaces.

Always follow the manufacturer’s instructions

when using any type of cleaning product.

-12-

For Machines Mfd. Since 10/22

South Bend Tools

Model SB1122 PREPARATION

The full-load current is not the maximum

amount of amps that the machine will draw. If

the machine is overloaded, it will draw additional

amps beyond the full-load rating.

If the machine is overloaded for a sufficient

length of time, damage, overheating, or fire may

result—especially if connected to an undersized

circuit. To reduce the risk of these hazards,

avoid overloading the machine during operation

and make sure it is connected to a power supply

circuit that meets the requirements in the

following section.

The full-load current rating is the amperage

a machine draws at 100% of the rated output

power. On machines with multiple motors, this is

the amperage drawn by the largest motor or sum

of all motors and electrical devices that might

operate at one time during normal operations.

Full-Load Current Rating

Full-Load Current Rating .................. 10 Amps

For your own safety and protection of property,

consult an electrician if you are unsure about

wiring practices or applicable electrical codes.

Note: The circuit requirements in this manual

are for

a dedicated circuit—where only one

machine will be running at a time. If this

machine will be connected to a shared circuit

where multiple machines will be running at

the same time, consult a qualified electrician to

ensure the circuit is properly sized.

Electrocution or fire may

occur if machine is not

correctly grounded and

attached to the power

supply. Use a qualified

electrician to ensure a safe

power connection.

Before installing the machine, consider the

availability and proximity of the required power

supply circuit. If an existing circuit does not meet

the requirements for this machine, a new circuit

must be installed.

To minimize the risk of electrocution, fire,

or equipment damage, installation work and

electrical wiring must be done by a

n electrician

or qualified service personnel

in accordance with

applicable electrical codes and safety standards.

Availability

Power Supply

Requirements

Circuit Requirements

This machine is prewired to operate on a power

supply circuit that has a verified ground and

meets the following requirements:

Nominal Voltage ........ 208V, 220V, 230V, 240V

Cycle .............................................................60 Hz

Phase ..............................................Single-Phase

Circuit Rating....................................... 15 Amps

Plug/Receptacle (included) ...........NEMA 6-15

This machine is equipped with a power cord

that has

an equipment-grounding wire and a

grounding plug

(similar to the figure below).

The plug

must only be inserted into a matching

receptacle (outlet)

that is properly installed and

grounded in accordance with all local codes and

ordinances.

Serious injury could occur if you connect

machine to power before completing setup

process. DO NOT connect to power until

instructed later in this manual.

South Bend Tools

For Machines Mfd. Since 10/22 Model SB1122

-13-

PREPARATION

Figure 6. NEMA 6-15 plug and receptacle.

Grounding Prong

Current Carrying Prongs

6-15 PLUG

GROUNDED

6-15 RECEPTACLE

Grounding Requirements

This machine must be grounded! In the event

certain types of malfunctions or breakdowns,

grounding provides a path of least resistance

for electric current

in order to reduce the risk of

electric shock.

This machine is equipped with a power cord

that has

an equipment-grounding wire and a

grounding plug

(similar to the figure below).

The plug

must only be inserted into a matching

receptacle (outlet)

that is properly installed and

grounded in accordance with all local codes and

ordinances.

DO NOT modify the

included plug or use an

adapter if it will not fit your

receptacle. Instead, have a

qualified electrician install

the proper receptacle on a

power supply circuit that

is grounded and meets

the requirements for this

machine.

Improper connection of the equipment-grounding

wire can result in a risk of electric shock. The

wire with green insulation (with or without

yellow stripes) is the equipment-grounding wire.

If repair or replacement of the power cord or

plug is necessary, do not connect the equipment-

grounding wire to a live (current carrying)

terminal.

Check with an electrician or qualiﬁ ed service

personnel if you do not understand these

grounding requirements, or if you are in doubt

about whether the tool is properly grounded.

If you ever notice that a cord or plug is

damaged or worn, disconnect it from power, and

immediately replace it with a new one.

Extension Cords

Minimum Gauge Size ............................14 AWG

Maximum Length (Shorter is Better) ....50 ft.

We do not recommend using an extension cord

with this machine. If you must use one, only

use it if absolutely necessary and only on a

temporary basis.

Extension cords cause voltage drop, which may

damage electrical components and shorten motor

life. Voltage drop increases as the extension cord

size gets longer and the gauge size gets smaller

(higher gauge numbers indicate smaller sizes).

Any extension cord used with this machine

must contain a ground wire, match the required

plug and receptacle listed in the

Circuit

Requirements

for the applicable voltage, and

meet the following requirements:

-14-

For Machines Mfd. Since 10/22

South Bend Tools

Model SB1122 PREPARATION

Unpacking

This item was carefully packaged to prevent

damage during transport. If you discover any

damage, please immediately call Customer

Service at

(360) 734-1540 for advice. You may

need to file a freight claim, so save the containers

and all packing materials for possible inspection

by the carrier or its agent.

Figure 7. Loose inventory.

If you cannot ﬁ nd an item on this list, carefully

check around/inside the machine and

packaging materials. Often, these items get

lost in packaging materials while unpacking or

they are pre-installed at the factory.

Inventory

Wood Crate (Figure 7) Qty

A. Bandsaw (Not Shown) ...................................1

B. Work Stop ....................................................... 1

C. Work Stop Rod ...............................................1

D. Drip Tray ........................................................ 1

E. Hex Bolts M12-1.75 x 50 ................................4

F. Hex Nuts M12-1.75 ........................................ 8

Cleaning & Protecting

The unpainted surfaces are coated at the factory

with a heavy-duty rust preventative that

prevents corrosion during shipment and storage.

The beneﬁ t of this rust preventative is that it

works very well. The downside is that it can be

time-consuming to thoroughly remove.

Be patient and careful when cleaning and

removing the rust preventative. The time spent

doing this will reward you with smooth-sliding

parts and a better appreciation for the proper

care of the unpainted surfaces.

Although there are many ways to successfully

remove the rust preventative, the following

process works well in most situations.

Before cleaning, gather the following:

• Disposable rags

• Cleaner/degreaser (citrus-based degreasers

work well and have non-toxic fumes)

• Safety glasses & disposable gloves

Basic steps for removing rust preventative:

1. Put on safety glasses and disposable gloves.

2. Coat surfaces that have rust preventative

with cleaner/degreaser and let them soak for

few minutes.

3. Wipe off surfaces. If cleaner/degreaser is

effective, rust preventative will wipe off

easily.

Note: To clean thick coats of rust preventative

on ﬂ at surfaces, like beds or tables, use

PLASTIC paint scraper to scrape off most of

coating before wiping it off with rag. (Do not

use metal scraper or it may scratch surface.)

4. Repeat Steps 2–3 as necessary until clean,

then coat all unpainted surfaces with quality

metal protectant or light oil to prevent rust.

Many cleaning solvents are toxic if

inhaled. Minimize risk by using these

products in well-ventilated area.

South Bend Tools

For Machines Mfd. Since 10/22 Model SB1122

-15-

PREPARATION

Min. 30"

Wall

36"

Electrical

Connection

68½"

Figure 8. Minimum working clearances.

Physical Environment

Electrical Installation

Lighting

Weight Load

Space Allocation

Weight Load

Refer to the Machine Speciﬁ cations for the

weight of your machine. Make sure that the

surface upon which the machine is placed will

bear the weight of the machine, additional

equipment that may be installed on the machine,

and the heaviest workpiece that will be used.

Additionally, consider the weight of the operator

and any dynamic loading that may occur when

operating the machine.

Space Allocation

Consider the largest size of workpiece that will

be processed through this machine and provide

enough space around the machine for adequate

operator material handling or the installation

of auxiliary equipment. With permanent

installations, leave enough space around

the machine to open or remove doors/covers

as required by the maintenance and service

described in this manual.

Physical Environment

The physical environment where your machine

is operated is important for safe operation and

longevity of

parts. For best results, operate this

machine in a dry environment that is free from

excessive moisture, hazardous

or flammable

chemicals, airborne abrasives, or extreme

conditions. Extreme conditions for this type

of machinery are generally those where the

ambient temperature

is outside the range of 41°–

104°F; the relative humidity

is outside the range

20–95% (non-condensing); or the environment

is subject to vibration, shocks, or bumps.

Electrical Installation

Place this machine near an existing power

source. Make sure all power cords are protected

from traffic, material handling, moisture,

chemicals, or other hazards. Make sure to leave

access to a means of disconnecting the power

source or engaging a lockout/tagout device.

Lighting

Lighting around the machine must be adequate

enough to perform operations safely. Shadows,

glare, or strobe effects that may distract or

impede the operator must be eliminated.

Children or untrained

people may be seriously

injured by this machine.

Only install in an access

restricted location.

Location

-16 -

For Machines Mfd. Since 10/22

South Bend Tools

Model SB1122 PREPARATION

This machine and its

parts are heavy! Serious

personal injury may occur

if safe moving methods are

not used. To reduce the

risk of a lifting or dropping

injury, ask others for help

and use power equipment.

The Model SB1122 requires the use of lifting

equipment such as a forklift, engine hoist, or

boom crane. DO NOT attempt to lift or move

machine without necessary assistance from other

people. Each piece of lifting equipment must be

rated for at least 1300 lbs. to support dynamic

loads that may be applied while lifting.

Review Power Supply Requirements section

on Page 12, then prepare a permanent location

for machine.

To assemble machine:

1. Move machine to its prepared location while

still inside shipping crate.

2. Remove top and sides of shipping crate, then

place small items aside in safe location.

Note: Do not discard shipping crate and

packaging until after Test Run.

Assembly

The machine must be fully assembled before it

can be operated. Before beginning the assembly

process, see Required for Setup on Page

11 and gather all listed items. To ensure the

assembly process goes smoothly, first clean any

parts that are covered or coated in heavy-duty

rust preventative (if applicable).

3. Remove (4) lag screws and flat washers that

secure machine to pallet (see Figure 9).

x 4

Figure 9. Location of lag screws.

4. Attach (4) lifting hooks to the lifting holes,

as shown in Figure 10, then use forklift (or

other lifting equipment) to lift machine just

enough to remove pallet.

Figure 10. Example of lifting hooks attached to lifting

holes.

South Bend Tools

For Machines Mfd. Since 10/22 Model SB1122

-17-

PREPARATION

5. Install (1) M12-1.75 x 50 hex bolt and (2)

M12-1.75 hex nuts at each lag screw hole

from Step 3 (see Figure 11).

Figure 11. Installing mounting hex bolts and hex nuts.

Lag Screw Hole

(1 of 4)

6. Lower machine so hex bolt heads from Step

5 rest on floor.

7. Adjust nuts from Step 5 until machine is

level.

8. Screw work stop rod into hole in vise table

shown in Figure 12.

Figure 12. Work stop installed.

Work Stop

Rod

Work Stop

10. Position drip tray on cabinet edge, as shown

in Figure 13.

Drip Tray

Cabinet

Edge

9. Slide work stop onto work stop rod, then

tighten set screw to secure (see Figure 12).

Figure 13. Drip tray positioned on cabinet edge.

Your machine was lubricated at the factory,

but we strongly recommend that you inspect all

lubrication points yourself and provide additional

lubrication if necessary. Refer to Lubrication on

Page 40 for specific details.

Initial Lubrication

Failure to follow reasonable lubrication

practices as instructed in this manual for your

machine could lead to premature failure of

components and void the warranty.

-18-

For Machines Mfd. Since 10/22

South Bend Tools

Model SB1122 PREPARATION

Test Run

After all preparation steps have been completed,

the machine and its safety features must be

tested to ensure correct operation. If you discover

a problem with the operation of the machine or

its safety components, do not operate it further

until you have resolved the problem.

Note: Refer to Troubleshooting on Page 59 for

solutions to common problems that may occur.

If you need additional help, contact our Tech

Support at (360) 734-1540.

Serious injury or death can result from using

this machine BEFORE understanding its

controls and related safety information. DO

NOT operate, or allow others to operate,

machine until the information is understood.

The test run consists of verifying the following:

• Hydraulic system runs correctly.

• All motors power up and run correctly.

• Workpiece contact safety switch works

correctly.

• Downfeed limit switch works correctly.

• EMERGENCY STOP button works correctly.

To test run machine:

1. Clear all setup tools and objects away from

machine.

2. Fill cutting ﬂuid reservoir with cutting

ﬂuid (refer to Cutting Fluid System

Maintenance on Page 46), if you have not

already done so. DO NOT run pump without

cutting ﬂuid or you will damage it.

3. Push EMERGENCY STOP button in (see

Figure 14).

To reduce risk of eye injury

from flying chips or lung

damage from breathing dust,

always wear safety glasses

and a respirator when

operating this machine.

Items Needed Qty

Safety Glasses (For Each Person) ..................1 Pr.

Respirator (For Each Person) ...............................1

Test Workpiece (Between 2"–31⁄2" Thick) .............1

Figure 14. Location of EMERGENCY STOP button.

EMERGENCY STOP

Button

4. Turn power switch to OFF (0) position (see

Figure 15).

Power Switch

Figure 15. Location of power switch.

DO NOT start machine until all preceding

setup instructions have been performed.

Operating an improperly set up machine may

result in malfunction or unexpected results

that can lead to serious injury, death, or

machine/property damage.

Page is loading ...

South bend SB1122 Owner's manual

Brand: South bend

Model: SB1122

Type: Owner's manual

Download PDF

report

South bend SB1122 Owner's manual

South bend SB1122 Owner's manual

Related papers

Other documents