TAMUZ HCM 115 Operating instructions

Brand: TAMUZ

Model: HCM 115

Type: Operating instructions

This manual is also suitable for

Operation Manual

GOLDEN EAGLE series

HCM 112 - HCM115 - HCM117 – HCM 117W

HCM 119 – HCM 123 - HCM123W - HCM 127W

HCM 132W - HCM 140W- HCM 142W

TAMUZ LCD Video Monitors

D-24558 Henstedt-Ulzburg ~ Fon & Fax: ..49 - (0)700 - TAMUZLCD [82 689 523]

under use of electronic systems, in any form (print, photocopy, microfilm or other proceedings),

without written permission of the right owner.

oder anderen Verfahren) ohne schriftliche Genehmigung des Rechteinhabers reproduziert oder unter

Verwendung elektronischer Systeme verarbeitet, vervielfältigt oder verbreitet werden.

Concept, Publishing and Production: E.L.B.E medi@, Henstedt-Ulzburg

Printed in Germany

I. Issue HCM Series GOLDEN EAGLE Broadcast Monitor

valid for Firmware Release 5.062 and above

TAMUZ - LCD Video Monitors

adivision of

TAMUZ Broadcast GmbH

Fon & Fax: +49 - (0)700 TAMUZLCD [82 689 523]

eMail: [email protected]

www.tamuz.tv

Rights reserved to change specifications and design without notice

Technische und farbliche Änderungen vorbehalten

GOLDEN EAGLE Broadcast Monitor

Table of Content

Introduction........................................................................5

LCD Video Monitor.........................................................5

GOLDEN EAGLE series Models........................................6

Differences in the series.................................................7

GOLDEN EAGLE Features..........................................7

ISO Product Quality........................................................7

Pixel Errors..................................................................7

Class of Usability.........................................................8

Class of Reflections.....................................................8

Wide Screen Format.......................................................8

Sampling the Video.................................................9

General Safety Instructions..............................................10

Limitation of the product..............................................10

Duty of care of the user................................................10

Safety symbols.............................................................10

Basic Safety Instructions..............................................11

Service and Maintenance..........................................11

Observe environmental protection prescriptions......11

Recycling......................................................................12

Recognition of the copyrights......................................12

Guarantee agreement:.....................................................13

Guarantee period......................................................13

Guarantee exceptions...............................................13

Guarantee Certification.............................................13

Warranty Card..................................................................14

Transport of the equipment.............................................15

Transportation..............................................................15

Weight.......................................................................15

Packing.........................................................................15

Return dispatch.........................................................15

Damages in transit....................................................15

Conformity Declaration....................................................16

Technical Data.................................................................17

System Hardware GOLDEN EAGLE series..................17

System Features GOLDEN EAGLE series....................18

Installation....................................................................19

First putting into Operation..........................................19

Mounting in 19“ Racks..............................................19

Mounting at VESA systems.......................................19

Ventilation.....................................................................20

Cleaning.......................................................................20

External Control Units...................................................20

Switching the Monitor on.............................................21

Power Save Mode.....................................................21

Suspend Mode......................................................22

Power Down Mode................................................22

Power Save Wake Up............................................22

Connections of the Monitor.............................................23

The Monitor Screen......................................................23

DC Voltage...................................................................24

Power Supply............................................................24

Video Inputs at Version HCM 1xx VB........................25

BNC Inputs................................................................25

Optional Input YC..................................................25

Optional Input DVI.................................................25

Signal Format............................................................25

Video Inputs at Version HCM 1xx DB.......................27

BNC Inputs................................................................27

Optional Input YC..................................................27

Optional Input DVI.................................................27

Signal Format............................................................27

VGA Input..................................................................29

Ethernet IP Interface.....................................................29

GPI/O Interface.............................................................30

Service Interface...........................................................31

Probe Interface.............................................................31

Operation.........................................................................32

Operation Elements at the GOLDEN EAGLE...............32

POWER Switch..........................................................32

Operation Buttons.....................................................32

Video Input Buttons...............................................33

Source Switch........................................................33

Aspect Ratio Switch...............................................34

TALLY Indicator.....................................................35

Option IR-Remote Controller........................................36

OSD Menu Operation......................................................37

OSD Menu....................................................................37

Main Menu ......................................................................38

Inputs Menu..............................................................39

Submenu Format for SDI inputs............................40

Submenu WSS...................................................40

Submenu Format for CCVS inputs........................41

Submenu WSS...................................................41

Submenu Format for VGA inputs..........................42

Scaling Menu.........................................................43

Submenu Scan Mode............................................44

Submenu Mirror.....................................................45

Submenu Signal for SDI inputs.............................47

Submenu P-I interlaced for SD-SDI Signals.......47

Submenu Display..................................................50

Submenu Zoom.....................................................51

Submenu Reset.....................................................52

Image Menu..............................................................53

Submenu Gamma.................................................54

Submenu Color Temperature................................55

Submenu Color Adjustments................................57

Submenu B/W.......................................................58

Submenu Negative................................................59

Submenu R/G/B.....................................................60

Submenu Aperture................................................62

Keyboard Menu.........................................................63

Submenu Keyboard...............................................64

System Menu............................................................65

Submenu Power On..............................................66

Submenu Search...................................................67

Submenu Processing............................................68

Submenu Language..............................................69

Submenu OSD.......................................................70

Submenu Wall.......................................................71

GOLDEN EAGLE Broadcast Monitor

Submenu RGB Adjust............................................72

Submenu Auto Color.............................................73

Submenu Probe Setup.......................................74

Submenu Calibrate............................................75

Submenu Brightness..........................................76

Submenu Measure.............................................77

Submenu Backlight...............................................78

Submenu Anti Sticking..........................................79

How to minimize the effect?...............................79

Service Menu...................................................................81

Submenu Info........................................................82

Submenu MTBFs...................................................83

Submenu Setup.....................................................84

Submenu No Signal..............................................85

Submenu Temperatures........................................86

Submenu Aux1 Configuration...............................87

Submenu Aux2 Configuration...............................88

Submenu Aux3 Configuration...............................89

Submenu Backlight...............................................90

Submenu Firmware...............................................91

Individual Adjustments and Setups.................................92

Aspect Ratio Setup.......................................................92

Setup Instructions.........................................................92

Setup VGA Signals................................................92

Setup HDTV Signals..............................................93

Setup SDI Signals.....................................................93

Setup CCVS Signals..............................................93

Reset the Monitor.........................................................94

Special Formats............................................................95

Setup BARCO VIVALDI..........................................95

Setup SONY BVE...................................................96

Interfacing the BVE 2000....................................96

Disturbed BVE Images ......................................97

Modification at the BVE 2000.............................97

Block Diagrams................................................................98

Blockdiagramm TFT Panels..................................98

GOLDEN EAGLE HCM 1xx DB...........................99

Alignment of LCD Monitors............................................100

Advantage of the TAMUZ AAC Technology............101

Color Alignment......................................................102

Quantization the video signal..............................103

How to align a TAMUZ monitor..................................104

Environment............................................................104

Alignment Setup......................................................104

Getting starting the Alignment................................104

Password for Alignment.......................................105

The Color Alignment Procedure.............................105

Starting Color Calibration.................................107

Starting Brightness Alignment..........................108

Starting Manual Measurement.........................109

Service Section .............................................................110

Changing a faulty Fuse..............................................110

1. Step: Open the Monitor...................................110

2. Step: Exchange the Fuse................................110

3. Step: Reassemble the Monitor........................110

Was kann an einem LCD Monitor repariert werden?.....111

Bemerkungen:........................................................115

Genereller Service:..............................................115

Reset (Wiederherstellen der Fabrikeinstellungen):

.............................................................................115

Defekte Hintergrundbeleuchtung:.......................115

Defekter Controller:..............................................115

Neues Display:.....................................................115

Frequently Asked Questions..........................................116

Safety Notice..................................................................117

Remarques de sécurité..................................................118

Indicaciones de seguridad............................................119

Instruções de segurança...............................................120

Norme di sicurezza........................................................121

Sikkerhedsanvisninger...................................................122

Säkerhetsinformationer..................................................123

Turvallisuusohjeet..........................................................124

Sikkerhetsanvisninger....................................................125

Öryggisleiðbeiningar......................................................126

Veiligheidsvoorschriften.................................................127

Introduction GOLDEN EAGLE

Introduction

LCD Video Monitor

The TAMUZ GOLDEN EAGLE series is a LCD monitor series with active TFT displays, designed as a

rack mountable or desktop unit for digital HD and/or SD video applications in studio or field produc-

tion environment. It covers a wide horizontal and vertical viewing angle at its best.

The series contains some standard 4:3 devices and some 16:9 devices. The wide screen displays al-

lows full screen presentation of standard 16:9 videos. In the user setup of the HCM xxxW HD version

any other format is individual adjustable.

The operation of the system was formed simply and user friendly. The GOLDEN EAGLE series moni-

tors offers an input port for serial digital Standard-Definition video as model HCM xxx DB. All HCM xxx

HD monitors for serial digital High-Definition video belongs to the sister series named FALCON.

All I/O ports are placed at the rear of the monitor, including the DC power connector for the power

supply. The power supply is detachable mounted on the rear.

The GOLDEN EAGLE series monitors are equipped with an RS232 port for communication with ex-

ternal remote systems and a port for a calibration probe. Therefore the unique AAC (Automatic Align-

ment and Calibration) is a standard feature within the GOLDEN EAGLE monitor series.

GOLDEN EAGLE series Models GOLDEN EAGLE

GOLDEN EAGLE series Models

The GOLDEN EAGLE series signal processor contains a set of micro computer controlled DSP's and

scalers with native serial capability. Various models are available within the GOLDEN EAGLE series.

Model / Interface Type Freq-V Hz Format Input 1 Input 2 Input 3 Input 4 Input 5 Input 6

HCM 112 DB 50 - 60 1024 x 768 CCVS CCVS YC SDI VGA VGA

HCM 112 VB 50 - 60 1024 x 768 CCVS CCVS YC --- VGA VGA

HCM 115 DB 50 - 60 1024 x 768 CCVS CCVS YC SDI VGA VGA

HCM 115 VB 50 - 60 1024 x 768 CCVS CCVS YC --- VGA VGA

HCM 117 DB 50 - 60 1280 x 1024 CCVS CCVS YC SDI VGA VGA

HCM 117 VB 50 - 60 1280 x 1024 CCVS CCVS YC --- VGA VGA

HCM 117W DB 50 - 60 1280 x 768 CCVS CCVS YC SDI VGA VGA

HCM 117W VB 50 - 60 1280 x 768 CCVS CCVS YC --- VGA VGA

HCM 119 DB 50 - 60 1280 x 1024 CCVS CCVS YC SDI VGA VGA

HCM 119 VB 50 - 60 1280 x 1024 CCVS CCVS YC --- VGA VGA

HCM 123 DB 50 - 60 1600 x 1200 CCVS CCVS YC SDI VGA VGA

HCM 123 VB 50 - 60 1600 x 1200 CCVS CCVS YC --- VGA VGA

HCM 123W DB 50 - 60 1366 x 768 CCVS CCVS YC SDI VGA VGA

HCM 123W VB 50 - 60 1366 x 768 CCVS CCVS YC --- VGA VGA

HCM 127W DB 50 - 60 1366 x 768 CCVS CCVS YC SDI VGA VGA

HCM 127W VB 50 - 60 1366 x 768 CCVS CCVS YC --- VGA VGA

HCM 132W DB 50 - 60 1366 x 768 CCVS CCVS YC SDI VGA VGA

HCM 132W VB 50 - 60 1366 x 768 CCVS CCVS YC --- VGA VGA

HCM 140W DB 50 - 60 1280 x 768 CCVS CCVS YC SDI VGA VGA

HCM 142W DB 50 - 60 1366 x 768 CCVS CCVS YC SDI VGA VGA

HCM 142W VB 50 - 60 1366 x 768 CCVS CCVS YC --- VGA VGA

GOLDEN EAGLE series Models GOLDEN EAGLE

Differences in the series

To include various custom features, multiple I/O modules are integrated to debut the GOLDEN EAG-

LE series. All types based on the unique Eagle or Falcon broadcast interface from TAMUZ.

GOLDEN EAGLE Features

The GOLDEN EAGLE series is equipped with a selected 4:3 or wide screen TFT panel from NEC,

AUO, ID-tech, LG-Philips, CMO, Sharp or Samsung production line. These panel types are state-of-

the-art high resolution panels which are available for the broadcast application at the market.

The HCM 1xx DB type has serial digital video signal (SDI) inputs with looped output and multiple ana-

log video inputs as standard.

The HCM 1xx VB type has multiple analog video inputs as standard. All units have additionally a ana-

log graphic signal (VGA) input as standard. Optionally a DVI inputs is available.

All GOLDEN EAGLE series monitors may be equipped with an IP addressable interface port to allow

remote communication from a PC network, see MRC software. Additionally a standard GPI/O port for

closed contact remote is equipped. The monitors are DC voltage powered by an attached or external

power supply. The housing is made of grey powder coated aluminium.

ISO Product Quality

For the production of TAMUZ GOLDEN EAGLE series video monitors LCD panels are used which

complies with the standard ISO 13406-2, error-class 1 or 2, only. This ISO standard 13406-2 defines

the scales for ergonomic and picture quality.

The LCD panel manufactures itself (like AU, CMO, LG-Philips, NEC, Samsung, Sharp or Toshiba) don't

guarantees absolute any errorlessness and don't guarantees that the LCD panels are free of sticking

effects.

Pixel Errors

Following limited values which may not exceed are valid.

ISO 13406-2 Typ 1 Typ 2 Typ 3 max. Distance connected Defects

Class I 0 0 0

Class II 2 2 5 1 defect pixel within a circle of 5 mm maximum 2 defective sub-pixel beside

each other

Class III 5 15 50 2 defect pixels within a circle of 5 mm maximum 2 defective sub-pixel beside

each other

Class IV 50 150 500

Error-type #1 describes errors by a complete bright (white) pixel, error-type #2 describes errors by a

complete dark (black) pixel, error-type #3 describes errors by defective sub-pixels of the colors red,

green and blue, which are completely bright or dark.

Asingle LCD pixel is built by a set of three sub-pixels, one of red, green and blue.

Error class I contains highly selected panels with no pixel error anyway. Panels within this class are ra-

re and very high priced. Panels from the error class II are the most common selection for high quality

industry applications. The error class III defines the mass production selection for IT applications. TFT

panels related to the error class IV are not useful for a LCD monitor at all.

GOLDEN EAGLE series Models GOLDEN EAGLE

Class of Usability

Next the standard ISO 13406-2 defines the classification of usability of LCD screens.

Usability Classification Description

Class 1 This permits several users to view the entire display area at the same time. This applies for intended

viewing distance (between 40 to 60 cm, depending on the size and resolution of the monitor) and for

aviewing angle within an 80° cone in front of the screen without any restriction of visual efficiency, in

such a way that brightness, contrast and color is maintained

Class 2 Permits a single user to view the entire area of the display. This applies for intended viewing distance

(between 40 to 60 cm, depending on the size and resolution of the monitor) from every position in

front of the screen, in such a way that brightness, contrast and color is maintained.

Class 3 Permits a single user to view the entire area of the display. This applies for intended viewing distance

(between 40 to 60 cm, depending on the size and resolution of the monitor) from one fixed position

in front of the screen, in such a way that brightness, contrast and color is maintained.

Class 4 Permits a single user to view the center area of the display. This applies for intended viewing

distance (between 40 to 60 cm, depending on the size and resolution of the monitor) from one fixed

position in front of the screen, in such a way that brightness, contrast and color is maintained.

All of the TAMUZ GOLDEN EAGLE series monitors comply with class 1.

Class of Reflections

The reflection characteristics of an LCD Screen are of particular importance in very bright ambient

conditions or in an environment with multiple light sources. The ISO standard provides for three quali-

ty classes.

Reflection Classification Description

Class 1 General office conditions without special requirements as to workspace lighting.

Class 2 Appropriate for most office conditions, with few exceptions.

Class 3 Appropriate for office environments, with controlled luminance conditions.

All of TAMUZ GOLDEN EAGLE series monitors comply with class 1.

All of TAMUZ GOLDEN EAGLE series monitors are equipped with a anti-reflective anti-glare filter ma-

de of glass.

Wide Screen Format

Among the TAMUZ GOLDEN EAGLE series there are LCD monitors equipped with a wide screen ac-

tive TFT display, developed to display 16:9 wide screen videos with a full screen image without any

loss.

Their native screen aspect ratio is 16:9 or similar, so real full screen 4:3 video sources fills the monitor

screen with small black areas at left and right, if the monitor is switched to 4:3 mode.

GOLDEN EAGLE series Models GOLDEN EAGLE

Note:IfyouusetheHCM 1xx GOLDEN EAGLE series monitor in a real full screen mode for

16:9 sources, the aspect ratio of the displayed image is correct!

Some sources don't produce a real 16:9 signal.

The TAMUZ HCM 1xx GOLDEN EAGLE series is able to handle different type of signals, see table be-

low.

Format horizontal

Resolution

vertical

Resolution

Pixel Style Input Source Äquivalent

16 : 9 1920 1080 square DVI-D full wide screen - full resolution W-UXGA

16 : 9 1920 1080 square SDI full wide screen - full resolution HDTV 1080 format

16 : 9 1280 720 square SDI full wide screen - full resolution HDTV 720 format

4 : 3 720 576 rectangle SDI standard video – full resolution SD 625 format

16 : 9 720 576 rectangle SDI wide screen video - full resolution SD 625 format

4 : 3 720 480 rectangle SDI standard video - full resolution SD 525 format

16 : 9 720 480 rectangle SDI wide screen video - full resolution SD 525 format

16 : 9 1024 576 square PAL wide screen video - full resolution analog composite

4 : 3 768 576 square PAL standard video - full screen analog composite

16 : 9 768 432 square PAL letterbox wide screen analog composite

Sampling the Video

TAMUZ develops special interfaces, labeled EAGLE and FALCON, to process the video to be dis-

played on a LCD Screen.

The EAGLE or FALCON interface operates within the GOLDEN EAGLE series is mainly a scaling mo-

de. This is necessary to do, because there is a difference between the incoming SD or HD video si-

gnal formats and the panel resolutions.

The pixel-to-pixel mode takes place, only when the native resolution of the TFT fits to the video resolu-

tion. Each incoming pixel information will be transferred to its corresponding geometrical position at

the display. This happens with computer signals from the DVI-D port and with High-Definition digital si-

gnals from the HD-SDI port too.

Most of the common SMPTE 274M and 296M HD formats are supported.

General Safety Instructions GOLDEN EAGLE

General Safety Instructions

Limitation of the product

The LCD technology itself and some LCD panels built-in the TAMUZ GOLDEN EAGLE HCM 1xx se-

ries have limitations which the user have to understand and accept.

The user must accept that it is necessary



to avoid condensation of water within the GOLDEN EAGLE series. It may result in

improper operation or disconnection of electrodes.



not to exceed the absolute maximum rating value. (input voltage variation, environmental

temperature and so on) Otherwise the monitor may be damaged.



to avoid image sticking. If the monitor keeps displaying the same pattern for a long period

of time without any movement, the image may be „sticked“ to the screen. It is

recommended to use the „anti-sticking“ screen saver. See chapter Submenu Anti-Sticking



to handle the monitor carefully in order not to be stressed. The monitor is equipped with

sensitive glass plates, light bulbs and electronics.



to add ultra-violet ray filters for outdoor operation.

Duty of care of the user

The GOLDEN EAGLE HCM 1xx series was designed and built under the harmonized norms to be ad-

hered as well as further technical specifications. It corresponds to the state of the art and ensures a

maximum amount of safety.

However, this safety can only be reached, if all safety measures are taken in the operational practice.

It is the duty of the GOLDEN EAGLE HCM 1xx series user, to plan these measures and check their

explanation.

The user must guarantee that



the GOLDEN EAGLE series is only used as agreed (cf. chapter product specification)



the GOLDEN EAGLE series is operated only in faultless, working condition and

particularly the safety facilities are checked for their function efficiency regularly



the GOLDEN EAGLE series

operator's manual always be placed in a complete and

legible condition for disposal



only sufficiently qualified and authorized staff operates, maintains and repairs the GOLDEN

EAGLE series



staff is instructed to meet work safety and environmental protection regulation and knows

the operator's manual as well as there particularly contained safety instructions



all appropriate safety and warning notes not being removed and remaining legible at the

GOLDEN EAGLE series

Constructive changes at the GOLDEN EAGLE series may be carried out only after written permission

by the manufacturer!

Safety symbols

The following safety symbols are applied in this operator's manual. These symbols shall primarily draw

the attention of the reader to the text of the accompanying safety note.

This symbol points out that there are dangers for life and health

of persons.

General Safety Instructions GOLDEN EAGLE

This symbol indicates information which contributes for a better

understanding of the function of the equipment.

This symbol points out that there are dangers for material and

environment or the equipment himself.

Warning about dangerous electrical voltages to or within the

equipment.

Basic Safety Instructions

The GOLDEN EAGLE series only may be used by persons who are trained, authorized and has

knowledge of the operator's manual.

Before every production, check the GOLDEN EAGLE series for visible damages and make sure that it

is operated in faultless condition! Report noticed deficiencies to the supervisor immediately or schedu-

le to restore by qualified persons.

Service and Maintenance

Adhere to the specified inspection and maintenance intervals in the operator's manual!



Before maintenance and repair work it must be guaranteed that all parts of the GOLDEN

EAGLE series have cooled down on space temperature!



Smear-, cool- or cleaning-fluids, endangering the environment, must be disposed duly!



Repair work on the electrical power supply of the GOLDEN EAGLE series system must be

done by a trained electric qualified employee!



Damaged lines or cables have to be immediately replaced!

Released bolted joints must be checked for solid seat before putting into operation after maintenance

or repair work and it must be guaranteed, that removed system-unit cover parts or filters were re-in-

stalled!

Observe environmental protection prescriptions

The legal duties for waste avoidance and proper utilization for elimination must be adhered at all work

stations, also including the GOLDEN EAGLE.

During repair, installation and maintenance work, be aware of water endangering substances such as;



Lubricating greases and oil



Hydraulics oils



Coolant



solvent containing cleaning liquids

don't load the floor or reach into the sewage system!

Note:The valid environmental protection prescriptions must be observed.

These water endangering substances must be kept, transported, caught and disposed in suitable con-

tainers!

General Safety Instructions GOLDEN EAGLE

Recycling

If GOLDEN EAGLE series monitor no longer operates or is un-repairable, please do not dispose the

monitor in the trash.

Please return the monitor to your local dealer or TAMUZ directly, we will grant the correct and suitable

recycling of the old monitor.

Note: Don't waste unused, old or broken monitors. Follow your local environmental protection

prescriptions.

Recognition of the copyrights

The user of the GOLDEN EAGLE series appreciates, that in the GOLDEN EAGLE series contains

software programs as well as this documentation is subject to the copyright laws as well as copyright

propriety and other protection rights and does not purchase this with the acquisition or the use of the

GOLDEN EAGLE series system by any time. The user obtains rather merely the right for the exclusive

use of the GOLDEN EAGLE series.

In the GOLDEN EAGLE series contained software as well as the accompanying documentation may

not be changed, enlarged or adapted to other systems or translated into other languages, without writ-

ten permission of the author. With the installation and use of the GOLDEN EAGLE series the user re-

cognizes these license and use conditions.

Note: The GOLDEN EAGLE series system contains copyright protected software and

documentation's.

Guarantee agreement: GOLDEN EAGLE

Guarantee agreement:

In the GOLDEN EAGLE HCM 1xx series system contains software and the instructions are left to the

user as they are. This means, the author of the software or the instructions doesn't assume any liability

for the suitability of the software or the documentation to any special purpose. He particularly isn't lia-

ble for damages or sequential damages which indirectly deliberately or unintentionally arise from the

use of the GOLDEN EAGLE HCM 1xx series or the documentation directly.

The GOLDEN EAGLE HCM 1xx series system and the documentation can be changed and enlarged

without previous announcement at any time. Rights for updates free of charge does not apply.

Guarantee period

TAMUZ - LCD Video Monitors, the manufacturer of the GOLDEN EAGLE HCM 1xx series grants a

guarantee period of 24 months on the faultless function of the system and its components.

Guarantee exceptions

Claims for defects shall not exist in cases of



natural wear and tear and damages, defects, reduced output, and changes of condition or

operation of our product due to extraneous cause (for example impact, blows, agitation,

water, fire), improper storage, treatment or erection, unusual climatic conditions, special

conditions at receipt or operational conditions at the location of use, or force majeure;



defects due to construction and material deficiencies, as far as the customer has specified

the construction or the material.



Image Sticking on the LCD-Panel, which is caused by permanent pictures as well as Gap

Mura on the LCD-Panel.

Guarantee Certification

Please, send in the full guarantee certification upon receipt of the product to the manufacturer or

suppliers within 21 working days. The manufacturer or supplier only then can grant possible rights to

claim under guarantee in full size and transmitting current information about software updates and in-

dications for expansions or for the operation of the equipment to you.

Note: Only if the guarantee card of the GOLDEN EAGLE HCM 1xx series monitor has been

returned intime to the manufacturer or supplier, rights to claim under guarantee can be

asserted against the manufacturer or supplier.

Warranty Card GOLDEN EAGLE

Warranty Card

To come in the position to reclaim your warranty rights, send in this warranty card within 21 days to

the manufacturer (TAMUZ - LCD Video Monitors, Germany) or your local dealer. Check the web site

www tamuz.tv, www tamuz.de or www tamuz.us for the correct address.

Garantie Registrierungskarte - Warranty Registration Card

Model: TAMUZ HCM Type:

Seriennummer: Serial Number:

Dieses Gerät wurde gekauft bei: - The Unit was purchased from:

Händler:

Ort.

Land:

Dealer:

City:

Country:

Verkaufsdatum: Purchase Date:

Dieses Gerät wurde gekauft von: - The Unit was purchased by:

Kunde: Customer:

Ansprechpartner: Contact Person:

Firma: Company:

Strasse: Street:

PLZ: Zip Code:

Ort: City:

Land: Country:

Telefon: Phone:

Telefax: Fax:

Email: Email:

Dieses Gerät wird eingesetzt im: - This Unit will be used at:

Regieraum: Control Room:

Schaltraum: Distribution:

Studio: Studio:

Ü-Wagen: OB-Truck:

Kopieranlage: VTR-Dubbing:

Schnittplatz: Editing:

Sprecher-Raum: Off-Room:

Andere: Other:

Unser Bestreben ist es, unsere Produkte kundengerecht zu entwickeln und fertigen. Wir sind Ihnen dankbar, wenn Sie sich

Zeit für Anregungen oder Kommentare nehmen:

Our mutual interest is, to design and manufacture practical products. We appreciate you taking the time to note your

information and comments you may have.

Transport of the equipment GOLDEN EAGLE

Transport of the equipment

Transportation

The GOLDEN EAGLE HCM 1xx series is a sensitive electronic product and should be transported

with all caution. Throwing the equipment or hard pushes during the transport must be avoided.

Weight

The GOLDEN EAGLE HCM 1xx series weights inclusive of the accessories and his packing more

then 10 kg and should be carried under consideration of the accident prevention measures or trans-

ported with help of corresponding aids therefore by two persons.

Note: Observe the accident prevention prescriptions at the transport of the GOLDEN

EAGLE HCM 1xx series to the avoidance of persons and damages to property.

Packing

The GOLDEN EAGLE HCM 1xx series is delivered in a special transport carton. It recommends itself

to keep this carton and the accompanying packaging. So in the case of a later necessary transport

and dispatch the equipment can be packed and protect against damages as delivered to you.

Return dispatch

At a return dispatch without original packing to the supplier or manufacturer the liability is excluded.

Don't forget to ask for a RMA (return material authorization) number before you send any material

back to the manufacturer. Check for a RMA the web-site www.tamuz.tv, www.tamuz.de or www.ta-

muz.us.

Damages in transit

Check the contents of the received transport carton with the delivery note or the invoice on complete-

ness and inform your supplier if you have missing parts upon receipt of the product. Please contact

within 5 working days. If you receive a delivery on which the transport carton or the contents is dama-

ged, proceed after the known guidelines of the cargo shipper, (which as a rule is enclosed with the

delivering papers). Perhaps stricter terms must be taken into account.

Note:Check before using the GOLDEN EAGLE HCM 1xx series whether damages in transit

have been happened and arrange a repair of these damages if necessary.

Conformity Declaration GOLDEN EAGLE

Conformity Declaration

to EMV/EMC guideline (89/336/EC)

to low-voltage guideline (73/23/EC chapter 10)

The manufacturer:

TAMUZ - LCD Video Monitors

Tiedenkamp 16

D-24558 Henstedt-Ulzburg

declares hereby, that the product:

Product name: LCD Video Monitor

Model number: GOLDEN EAGLE HCM 1xx series

Year of construction: 2002

corresponds to the regulations of the guidelines described above:

The following harmonized norms were used:

EN 55011 ISM Equipment, Group 1, Class A

EN 55022 Conducted Emissions, Class B

EN 50081-2 Generic standard interference transmission, industry area

EN 50082-2 Generic standard interference immunity, industry area

prEN55103-1 EMV product family norm for Audio-, Video and audio-visual facilities

as well as for studio light control facilities for the professional usage,

-Part 1: Limiting values and measurement procedure for disturbing

emissions

prEN55103-2 EMV product family norm for Audio-, Video and audio-visual facilities

as well as for studio light control facilities for the professional usage,

-Part 2: Requirements on the interference immunity

EN 61000-3-2 Power Factor Harmonic Correction

EN 61000-3-3 Flicker & Voltage Fluctuation Limits

EN 61000-4-2 Electrostatic Discharge Immunity

EN 61000-4-3 Radiated Electromagnetic Fields

EN 61000-4-4 Fast Transients-Burst Immunity

EN 61000-4-5 Input Surge Immunity

EM 61000-4-6 Conducted RFI

EN 61000-4-11 Voltage Dips

The following national or international norms (or parts/clauses from this) and specifications were used:

DIN EN 6099 Verbindungsmaterial für Niederspannungsstromkreise für Haushalt

und ähnliche Zwecke; Teil 1: Allgemeine Anforderungen

IEC 127-6 Geräteschutzsicherungen

Henstedt-Ulzburg, 18.04.2002

CEO / President

Technical Data GOLDEN EAGLE

Technical Data

System Hardware GOLDEN EAGLE series

The hardware of the Video Monitor consists of the following components which are installed in an ele-

gant and emission shielded full metal system-unit cover of high quality:

Item HCM 112 HCM 115 HCM 117 HCM 117W HCM 119

System Frame HCM 108 HCM 115 HCM 117 HCM 117W HCM 119

Dimensions 222 x 216 x 100 363 x 308 x 80 436 x 378 x 75 410 x 308 x 80 446 x 396 x 100

Weight 2,8 kg 5,3 Kg 5,8 kg 6,5 kg 8,5 kg

Mounting ½ 19“ 4 RU 19“ 7 HE 19“ 9 HE 19“ 7 HE 19“ 9 HE

Display Size 8.4“ active matrix 15“ active matrix 17“ active matrix 17“W active matrix 19“ active matrix

Display Type NL10276BC16 *1NL10276BC20 *1LC170M *1LC171W03C *1M191C *1

Display Technology amorphous silicon amorphous silicon amorphous silicon amorphous silicon amorphous silicon

Resolution 1024 x 768 1024 x 768 1280 x 1024 1280 x 768 1280 x 1024

Dot Format RGB, square RGB, square RGB, square RGB, square RGB, square

Display Aspect Ratio 4 : 3 4 : 3 5 : 4 15 : 9 5 : 4

Color Format 24 bit full color 24 bit full color 24 bit full color 24 bit full color 24 bit full color

Luminance >300 cd/m2>400 cd/m2>400 cd/m2>400 cd/m2>300 cd/m2

Contrast >400 : 1 >400 : 1 >450 : 1 >450 : 1 >400 : 1

Viewing Angle ±85° H, ±85° V ±85° H, ±85° V ±85° H, ±85° V ±85° H, ±85° V ±85° H, ±85° V

Viewing Direction 06:00 h 06:00 h 06:00 h 06:00 h 06:00 h

Display Classification ISO 13406-2 ISO 13406-2 ISO 13406-2 ISO 13406-2 ISO 13406-2

Pixel Error Class class 2 class 2 class 2 class 2 class 2

*1=or similar alternative, *2=optional feature

Item HCM 123 HCM 123W HCM 127W HCM 132W HCM 142W

System Frame HCM 123 HCM 123W HCM 127W HCM 132W HCM 142W

Dimension 570 x 483 x 100 640 x 420 x 70 701 x 450 x 100 820 x 520 x 110 1060 x 680 x 110

Weight 13,2 kg 11,8 kg 16,5 kg 22 kg 30 kg

Mounting VESA 100, desktop VESA 100, desktop VESA 100, desktop VESA 100, desktop VESA 100, desktop

Display Size 23“ active matrix 23“W active matrix 27“W active matrix 32“W active matrix 42“ active matrix

Display Type M230UN *1L230W01 *1V270W02 *1LC320W02 *1LC420W02 *1

Display Technology amorphous silicon amorphous silicon amorphous silicon amorphous silicon amorphous silicon

Resolution 1600 x 1200 1366 x 768 1366 x 768 1366 x 768 1366 x 768

Dot Format RGB, square RGB, square RGB, square RGB, square RGB, square

Display Aspect Ratio 4 : 3 16 : 9 16 : 9 16 : 9 16 : 9

Color Format 24 bit full color 24 bit full color 24 bit full color 24 bit full color 24 bit full color

Luminance >300 cd/m2>300 cd/m2>300 cd/m2>250 cd/m2>350 cd/m2

Contrast >500 : 1 >500 : 1 >500 : 1 >500 : 1 >500 : 1

Viewing Angle ±85° H, ±85° V ±85° H, ±85° V ±85° H, ±85° V ±85° H, ±85° V ±85° H, ±85° V

Viewing Direction 06:00 h 06:00 h 06:00 h 06:00 h 06:00 h

Display Classification ISO 13406-2 ISO 13406-2 ISO 13406-2 ISO 13406-2 ISO 13406-2

Pixel Error Class class 2 class 2 class 2 class 2 class 2

Technical Data GOLDEN EAGLE

System Features GOLDEN EAGLE series

The video monitor GOLDEN EAGLE series is designed and equipped for the following requests, tasks

and applications :

Item HCM 112 HCM 115 HCM 117 HCM 117W HCM 119 HCM 123 HCM 123W HCM 127W HCM 132W HCM 142W

Application Digital Broadcast Control Monitor, MultiSync Computer Monitor

Graphic Format XGA XGA SXGA WXGA SXGA UXGA UXGA WXGA WXGA WXGA

Graphic I/O SubD-HD15

Video Format SD or SD/HD-SDI, auto detection

Video Level 800 mVpp ±10% digital

Video I/O BNC 75 Ohm terminated

Signal Format SD 1x SDI

Signal Format HD 1x SD/HD-SDI as option

analog Video Format analog composite, PAL, NTSC, SECAM *2

analog Video Level 1 Vpp

analog Video I/O BNC 75 Ohm active looped or terminated *2

Power Requirements DC 12 V +50/-15% @ XLR-4M DC 24 V ±20% @ XLR-5M

Power Consumption 26 34 38 40 46 60 48 52 56 68

Line Voltage 85 – 264 V AC, 50-60 Hz, short circuit proofed

Mains Input I/O IEC320 3pin

Operation

Temperature 0°C to +50°C at max. 80% humidity

Storage Temperature -30°C to +60°C at max. 95% humidity

*1=or similar alternative, *2=optional feature

Technical Data GOLDEN EAGLE

Installation

First putting into Operation

The video monitor GOLDEN EAGLE HCM 1xx series has an especially designed system-unit cover. It

contains all components of the monitor and it is installed operational. Modification is not usually requi-

red by the user.

Take the monitor GOLDEN EAGLE HCM 1xx from the packing and check it for possible damages in

transit. Please, Indications of damage, please refer to transportation documents.

Mounting in 19“ Racks

The smaller sized GOLDEN EAGLE HCM 1xx series (112, 115, 117, 119) are prepared for mounting

in standard 19“ racks.

Therefore mount the optional brackets on the left and right side of the monitor. The bigger sized GOL-

DEN EAGLE HCM 1xx is not prepared for mounting in a standard 19“ rack.

Note:Use the optional brackets to mount the monitor in a 19“ rack only.

Check the packaging for the optional brackets and keep them in a safe place for future usage.

Mounting at VESA systems

Starting with the type HCM 112 from the GOLDEN EAGLE series the monitors are equipped with a

set of VESA compatible treads at the rear.

On the rear side are treads for mounting some VESA 75/100 standard systems.

Technical Data GOLDEN EAGLE

Ventilation

The equipment is a low-powered self ventilated device which has no air ventilation openings. There

are no integrated fans producing a continuous stream of cooling air.

Note:When required check the chassis for faultiness and clean them regularly.

Cleaning

Remember the LCD screen itself is a sensitive device, Avoid scratching it. This device may be cleaned

with usual household glass cleaning fluids only. Avoid scrapers and rub on screen surface.

Note: When required check the device for faultiness regularly and clean it with a gentle glass

cleaner and soft cotton cloths. No acids or solvent may be used for cleaning.

External Control Units

External control units aren't necessary for the normal use of the monitor.

Note: The model HCM xxx is a digital display and didn't need any external control. It always

displays the incoming input signal at it best.

In case of special modes or for service an optional IR remote controller (EAGLE WHISTLE)is

available and necessary to obtain access to the OSD menu. This feature is available for all GOLDEN

EAGLE HCM 1xx monitors as an option.

The upper old style remote controller is supplemented by the blue colored new one.

Please ask your service department or dealer if necessary.

Page is loading ...

TAMUZ HCM 115 Operating instructions

Brand: TAMUZ

Model: HCM 115

Type: Operating instructions

This manual is also suitable for

Download PDF

report

TAMUZ HCM 115 Operating instructions

This manual is also suitable for

TAMUZ HCM 115 Operating instructions

Related papers

Other documents