ROOMS TO GO 11505837 Assembly Instructions

Type
Assembly Instructions
Note: Make sure all PLUGS are connected
on the product before plugging power
cord into power outlet. If not damage can
occur.
The USB ports (where applicable) are
designed with working voltage of 5V, and
can NOT be used to supply power for
laptop computers (neither PC or Mac).
Plugging a laptop computer to the USB
port may end up damaging either the
computer or the USB port due to
Note: Make sure all PLUGS are connected
on the product before plugging power cord
into power outlet. If not damage can occur.
The USB ports (where applicable) are
designed with working voltage of 5V, and
can NOT be used to supply power for
laptop computers (neither PC or Mac).
Plugging a laptop computer to the USB port
may end up damaging either the computer
or the USB port due to unmatched working
voltage.
Note: Make sure all PLUGS are connected
on the product before plugging power
cord into power outlet. If not damage can
occur.
The USB ports (where applicable) are
designed with working voltage of 5V, and
can NOT be used to supply power for
laptop computers (neither PC or Mac).
Plugging a laptop computer to the USB
port may end up damaging either the
computer or the USB port due to
Assembly instructions for OPTIONS 5021-52phr
Lift up cover over
the adjustable
screws.Use screw
driver and turn
clockwise to tighten
if needed.
Adjustable screws
Base lights,cup holder
ON/ OFF
Seat/Open
Seat/Clos
USB
Headrest/Clos
Headrest/Open
Raffel Cup
Holder
A
B
4.Connect the
headrest wire A with
wire B in the rear of
the seat.(Same as it in
5Plug the wall power
cord into DC port in
the rear of the
seat,then plug another
side into power outlet
to operate.
2.Connect the reading
lights wire G with H
in the rear of the
seat.
G
H
3.Connect the
wireless charger E
with F in the rear of
E
F
Assembly instructions for OPTIONS 5021-73phr
1.Slide the metal post
over metal
receiver,press both sides
until locked in place.
A
B
4.Connect the
headrest wire A with
wire B in the rear of
the seat.(Same as it in
left side)
5.Plug the wall power
cord into DC port in
the rear of the
seat,then plug
another side into
power outlet to
2.Unzip the dust
cover in the bottom
of console,remove
the console back.
3.
Slide the metal
post over metal
receiver,press
both sides until
locked in place.
Assembly instructions for OPTIONS 5021-85phr
Raffel Cup
Holder
1.Slide the metal post over
metal receiver,press both sides
until locked in place.
1
.Slide the metal post over
metal receiver,press both
sides until locked in place.
A
B
2.Connect the
headrest wire A with
wire B in the rear of
the seat.
3.Plug the wall power cord into
DC port in the rear of the
seat,then plug another side into
power outlet to operate.
Base lights,cup holder
ON/ OFF
Seat/Open
Seat/Clos
USB
Headrest/Clos
Headrest/Open
Raffel Cup
Holder
Base lights,cup holder
ON/ OFF
Seat/Open
Seat/Clos
USB
Headrest/Clos
Headrest/Open
Raffel Cup
Holder
Raffel cup
holder
Base lights,cup
holder
ON/ OFF
Note: Make sure all PLUGS are connected
on the product before plugging power cord
into power outlet. If not damage can occur.
The USB ports (where applicable) are
designed with working voltage of 5V, and
can NOT be used to supply power for
laptop computers (neither PC or Mac).
Plugging a laptop computer to the USB
port may end up damaging either the
computer or the USB port due to
unmatched working voltage.
3.Slide the metal
receiver over the metal
post.Press both sides of
back firmly downward
until locked in place.
Assembly instructions for OPTIONS 5021-10
Raffel cup
holder
4.Plug the wall power cord into
DC port in the rear of the
seat,then plug another side
into power outlet to operate.
1.Unzip the dustcover
underneath,remove the
legs from the red bag.
2.Attach the legs in
clockwise.
  • Page 1 1
  • Page 2 2

ROOMS TO GO 11505837 Assembly Instructions

Type
Assembly Instructions

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI