GIGA-BYTE TECHNOLOGY H410M DS2V V2 User manual

Brand: GIGA-BYTE TECHNOLOGY

Model: H410M DS2V V2

Type: User manual

This manual is also suitable for

H410M S2 V2

For more product details, please visit GIGABYTE's website.

To reduce the impacts on global warming, the packaging materials of this product

are recyclable and reusable. GIGABYTE works with you to protect the environment.

H410M S2 V2

User's Manual

Rev. 1001

The trademarks mentioned in this manual are legally registered to their respective owners.

Disclaimer

Information in this manual is protected by copyright laws and is the property of GIGABYTE.

Changes to the specications and features in this manual may be made by GIGABYTE without

prior notice. No part of this manual may be reproduced, copied, translated, transmitted, or

published in any form or by any means without GIGABYTE's prior written permission.

In order to assist in the use of this product, carefully read the User's Manual.

For product-related information, check on our website at: https://www.gigabyte.com

Identifying Your Motherboard Revision

The revision number on your motherboard looks like this: "REV: X.X." For example, "REV:

1.0" means the revision of the motherboard is 1.0. Check your motherboard revision before

updating motherboard BIOS, drivers, or when looking for technical information.

Example:

- 3 -

Table of Contents

H410M S2 V2 Motherboard Layout .................................................................................4

Chapter 1 Hardware Installation .....................................................................................5

1-1 Installation Precautions .................................................................................... 5

1-2 ProductSpecications ...................................................................................... 6

1-3 Installing the CPU ............................................................................................ 9

1-4 Installing the Memory ....................................................................................... 9

1-5 Installing an Expansion Card ......................................................................... 10

1-6 Back Panel Connectors .................................................................................. 10

1-7 Internal Connectors ........................................................................................ 12

Chapter 2 BIOS Setup ..................................................................................................19

2-1 Startup Screen ............................................................................................... 19

2-2 The Main Menu .............................................................................................. 20

2-3 Favorites (F11) ............................................................................................... 21

2-4 Tweaker .......................................................................................................... 22

2-5 Settings .......................................................................................................... 27

2-6 System Info. ................................................................................................... 32

2-7 Boot ................................................................................................................ 33

2-8 Save & Exit ..................................................................................................... 36

Chapter 3 Appendix ......................................................................................................37

3-1 ConguringaRAIDSet .................................................................................. 37

3-2 Installing an Intel® Optane™ Memory .............................................................. 39

3-3 DriversInstallation .......................................................................................... 41

RegulatoryNotices .................................................................................................... 42

Contact Us ................................................................................................................ 43

- 4 -

H410M S2 V2 Motherboard Layout

* The box contents above are for reference only and the actual items shall depend on the product package you obtain.

The box contents are subject to change without notice.

Box Contents

5H410M S2 V2 motherboard

5Motherboard driver disc 5Two SATA cables

5User's Manual 5I/O Shield

KB_MS

CPU_FAN

SYS_FAN

LGA1200

ATX

H410M S2 V2

F_AUDIO COMA LED_C

AUDIO

BAT

ATX_12V_2X4

Intel® H470

U32

CODEC

CLR_CMOS

M_BIOS

VGA

USB_LAN

PCIEX16

80 60 42

PCIEX1_1

PCIEX1_2

iTE®

Super I/O

Intel®

GbELAN

F_USB F_PANEL

SPI_TPM

F_U32

DDR4_B1

DDR4_A1

M2A_SB

3 2

5 4

SATA3

USB20

Chapter 1 Hardware Installation

1-1 Installation Precautions

The motherboard contains numerous delicate electronic circuits and components which can become

damagedasaresultofelectrostaticdischarge(ESD).Priortoinstallation,carefullyreadtheuser's

manual and follow these procedures:

•Prior to installation, make sure the chassis is suitable for the motherboard.

•Priortoinstallation,donotremoveorbreakmotherboardS/N(SerialNumber)stickeror

warranty sticker provided by your dealer. These stickers are required for warranty validation.

•Always remove the AC power by unplugging the power cord from the power outlet before

installing or removing the motherboard or other hardware components.

•When connecting hardware components to the internal connectors on the motherboard, make

sure they are connected tightly and securely.

•When handling the motherboard, avoid touching any metal leads or connectors.

•It is best to wear an electrostatic discharge (ESD) wrist strap when handling electronic

componentssuchasamotherboard,CPUormemory.IfyoudonothaveanESDwriststrap,

keepyourhandsdryandrsttouchametalobjecttoeliminatestaticelectricity.

•Prior to installing the motherboard, please have it on top of an antistatic pad or within an

electrostatic shielding container.

•Before connecting or unplugging the power supply cable from the motherboard, make sure

the power supply has been turned off.

•Before turning on the power, make sure the power supply voltage has been set according to

the local voltage standard.

•Before using the product, please verify that all cables and power connectors of your hardware

components are connected.

•To prevent damage to the motherboard, do not allow screws to come in contact with the

motherboard circuit or its components.

•Make sure there are no leftover screws or metal components placed on the motherboard or

within the computer casing.

•Donotplacethecomputersystemonanunevensurface.

•Donotplacethecomputersysteminahigh-temperatureorwetenvironment.

•Turning on the computer power during the installation process can lead to damage to system

components as well as physical harm to the user.

•If you are uncertain about any installation steps or have a problem related to the use of the

product,pleaseconsultacertiedcomputertechnician.

•If you use an adapter, extension power cable, or power strip, ensure to consult with its installation

and/or grounding instructions.

- 5 -

1-2 ProductSpecications

CPU Support for 10th Generation Intel® Core™ i9 processors/Intel® Core™ i7 processors/

Intel® Core™ i5 processors/Intel® Core™ i3 processors/Intel® Pentium® processors/

Intel® Celeron® processors in the LGA1200 package

(Go to GIGABYTE's website for the latest CPU support list.)

L3 cache varies with CPU

Chipset Intel® H470 Express Chipset

Memory Intel® Core™ i9/i7 processors:

- SupportforDDR42933/2666/2400/2133MHzmemorymodules

Intel® Core™ i5/i3/Pentium®/Celeron® processors:

- SupportforDDR42666/2400/2133MHzmemorymodules

2xDDR4DIMMsocketssupportingupto64GB(32GBsingleDIMMcapacity)

of system memory

Dualchannelmemoryarchitecture

SupportforECCUn-bufferedDIMM1Rx8/2Rx8memorymodules (operatein

non-ECC mode)

Supportfornon-ECCUn-bufferedDIMM1Rx8/2Rx8/1Rx16memorymodules

SupportforExtremeMemoryProle(XMP)memorymodules

(Go to GIGABYTE's website for the latest supported memory speeds and memory

modules.)

Onboard

Graphics

Integrated Graphics Processor-Intel®HDGraphicssupport:

- 1xD-Subport,supportingamaximumresolutionof1920x1200@60Hz

Maximum shared memory of 512 MB

Audio Realtek®AudioCODEC

HighDenitionAudio

2/4/5.1/7.1-channel

* Tocongure7.1-channelaudio,youneedtoopentheaudiosoftwareandselect

Deviceadvanced settings> PlaybackDevice tochange thedefault settingrst.

PleasevisitGIGABYTE'swebsitefordetailsonconguringtheaudiosoftware.

LAN Intel®GbELANchip(1000/100Mbit)

Expansion Slots 1 x PCI Express x16 slot, running at x16

2 x PCI Express x1 slots

(The PCI Express slots conform to PCI Express 3.0 standard.)

Storage Interface  1 x M.2 connector (Socket 3, M key, type 2242/2260/2280 SATA and PCIe x4/

x2SSDsupport)

4 x SATA 6Gb/s connectors

SupportforRAID0,RAID1,RAID5,andRAID10

Intel® Optane™MemoryReady

- 6 -

USB Chipset:

- 4 x USB 3.2 Gen 1 ports (2 ports on the back panel, 2 ports available through

the internal USB header)

- 6 x USB 2.0/1.1 ports (4 ports on the back panel, 2 ports available through

the internal USB header)

Internal

Connectors

1 x 24-pin ATX main power connector

1 x 8-pin ATX 12V power connector

4 x SATA 6Gb/s connectors

1 x CPU fan header

1 x system fan header

1xRGBLEDstripheader

1 x front panel header

1 x front panel audio header

1 x USB 3.2 Gen 1 header

1 x USB 2.0/1.1 header

 1 x Trusted Platform Module header (For the GC-TPM2.0 SPI/GC-TPM2.0 SPI

2.0 module only)

1 x serial port header

1 x Clear CMOS jumper

Back Panel

Connectors

1 x PS/2 keyboard port

1 x PS/2 mouse port

1xD-Subport

2 x USB 3.2 Gen 1 ports

4 x USB 2.0/1.1 ports

1xRJ-45port

3 x audio jacks

I/O Controller iTE® I/O Controller Chip

Hardware

Monitor

Voltage detection

Temperature detection

Fan speed detection

Overheating warning

Fan fail warning

Fan speed control

* Whether the fan speed control function is supported will depend on the cooler you

install.

BIOS 1x256Mbitash

Use of licensed AMI UEFI BIOS

PnP1.0a,DMI2.7,WfM2.0,SMBIOS2.7,ACPI5.0

- 7 -

Unique Features Support for APP Center

* Available applications in APP Center may vary by motherboard model. Supported

functionsofeachapplicationmayalsovarydependingonmotherboardspecications.

- @BIOS

- AmbientLED

- EasyTune

- Fast Boot

- Game Boost

- ON/OFFCharge

- Smart Backup

- System Information Viewer

Support for Q-Flash

Support for Xpress Install

Bundled

Software

Norton® Internet Security (OEM version)

cFosSpeed

Operating

System Support for Windows 10 64-bit

Form Factor Micro ATX Form Factor; 22.6cm x 18.5cm

* GIGABYTEreservestherighttomakeanychangestotheproductspecicationsandproduct-relatedinformationwithout

prior notice.

- 8 -

Please visit GIGABYTE's website

for support lists of CPU, memory

modules,SSDs,andM.2devices.

Please visit the Support\Utility List

page on GIGABYTE's website to

download the latest version of apps.

1-3 Installing the CPU

Please visit GIGABYTE's website for details on hardware installation.

Installing the CPU

Locate the alignment keys on the motherboard CPU socket and the notches on the CPU.

Do not remove the CPU socket cover before inserting the CPU. It may pop off from the load

plate automatically during the process of re-engaging the lever after you insert the CPU.

Triangle Pin One Marking on the CPU

NotchNotch

LGA1200 CPU

Alignment

Key

Alignment

Key

LGA1200 CPU Socket

Pin One Corner of the CPU Socket

ReadthefollowingguidelinesbeforeyoubegintoinstalltheCPU:

•Make sure that the motherboard supports the CPU.

(Go to GIGABYTE's website for the latest CPU support list.)

•Always turn off the computer and unplug the power cord from the power outlet before installing the

CPU to prevent hardware damage.

•Locate the pin one of the CPU. The CPU cannot be inserted if oriented incorrectly. (Or you may

locate the notches on both sides of the CPU and alignment keys on the CPU socket.)

•Apply an even and thin layer of thermal grease on the surface of the CPU.

•DonotturnonthecomputeriftheCPUcoolerisnotinstalled,otherwiseoverheatinganddamage

of the CPU may occur.

•SettheCPUhostfrequencyinaccordancewiththeCPUspecications.Itisnotrecommended

thatthesystembusfrequencybesetbeyondhardwarespecicationssinceitdoesnotmeetthe

standard requirements for the peripherals. If you wish to set the frequency beyond the standard

specications,pleasedosoaccordingtoyourhardwarespecicationsincludingtheCPU,graphics

card, memory, hard drive, etc.

1-4 Installing the Memory

Readthefollowingguidelinesbeforeyoubegintoinstallthememory:

•Make sure that the motherboard supports the memory. It is recommended that memory of the same

capacity, brand, speed, and chips be used.

(Go to GIGABYTE's website for the latest supported memory speeds and memory modules.)

•Always turn off the computer and unplug the power cord from the power outlet before installing the

memory to prevent hardware damage.

•Memory modules have a foolproof design. A memory module can be installed in only one direction.

If you are unable to insert the memory, switch the direction.

DualChannelMemoryConguration

ThismotherboardprovidestwomemorysocketsandsupportsDualChannelTechnology.Afterthememory

isinstalled,theBIOSwillautomaticallydetectthespecicationsandcapacityofthememory.EnablingDual

Channel memory mode will double the original memory bandwidth.

- 9 -

1-6 Back Panel Connectors

PS/2 Keyboard and PS/2 Mouse Port

Use the upper port (green) to connect a PS/2 mouse and the lower port (purple) to connect a PS/2 keyboard.

D-Sub Port

TheD-Subportsupportsa15-pinD-Subconnectorandsupportsamaximumresolutionof1920x1200@60Hz

(the actual resolutions supported depend on the monitor being used). Connect a monitor that supports

D-Subconnectiontothisport.

USB 2.0/1.1 Port

TheUSBportsupportstheUSB2.0/1.1specication.UsethisportforUSBdevices.

USB 3.2 Gen 1 Port

TheUSB3.2Gen1portsupportstheUSB3.2Gen1specicationandiscompatibletotheUSB2.0

specication.UsethisportforUSBdevices.

RJ-45 LAN Port

TheGigabitEthernetLANportprovidesInternetconnection at up to 1 Gbpsdatarate.The following

describesthestatesoftheLANportLEDs.

1-5 Installing an Expansion Card

Readthefollowingguidelinesbeforeyoubegintoinstallanexpansioncard:

•Make sure the motherboard supports the expansion card. Carefully read the manual that came

with your expansion card.

•Always turn off the computer and unplug the power cord from the power outlet before installing an

expansion card to prevent hardware damage.

DuetoCPUlimitations,readthefollowingguidelinesbeforeinstallingthememoryinDualChannelmode.

1. DualChannelmodecannotbeenabledifonlyonememorymoduleisinstalled.

2. WhenenablingDualChannelmodewithtwomemorymodules,itisrecommendedthatmemoryof

the same capacity, brand, speed, and chips be used.

ThetwoDDR4memorysocketsaredividedintotwochannelsandeachchannelhasonememorysocketas

following:

ChannelA:DDR4_A1

ChannelB:DDR4_B1

•Whenremovingthecableconnectedtoabackpanelconnector,rstremovethecablefromyour

device and then remove it from the motherboard.

•Whenremovingthecable,pullitstraightoutfromtheconnector.Donotrockitsidetosideto

prevent an electrical short inside the cable connector.

ActivityLED

Connection/

SpeedLED

LANPort

ActivityLED:

Connection/SpeedLED:

State Description

Orange 1 Gbps data rate

Green 100 Mbps data rate

Off 10 Mbps data rate

State Description

Blinking Datatransmissionorreceivingisoccurring

On Nodatatransmissionorreceivingisoccurring

- 10 -

Line In/Rear Speaker Out (Blue)

The line in jack. Use this audio jack for line in devices such as an optical drive, walkman, etc.

Line Out/Front Speaker Out (Green)

The line out jack.

Mic In/Center/Subwoofer Speaker Out (Pink)

The Mic in jack.

AudioJackCongurations:

Jack Headphone/

2-channel 4-channel 5.1-channel 7.1-channel

LineIn/RearSpeakerOut aaa

Line Out/Front Speaker Out aaaa

Mic In/Center/Subwoofer Speaker Out a a

Front Panel Line Out/Side Speaker Out a

PleasevisitGIGABYTE'swebsitefordetailsonconguringtheaudiosoftware.

•You can change the functionality of an audio jack using the audio software.

•Tocongure 7.1-channelaudio, you need to open the audio software and select Device

advancedsettings>PlaybackDevicetochangethedefaultsettingrst.

- 11 -

1-7 Internal Connectors

Readthefollowingguidelinesbeforeconnectingexternaldevices:

•First make sure your devices are compliant with the connectors you wish to connect.

•Before installing the devices, be sure to turn off the devices and your computer. Unplug the power

cord from the power outlet to prevent damage to the devices.

•After installing the device and before turning on the computer, make sure the device cable has

been securely attached to the connector on the motherboard.

4 1 3

1312

1) ATX_12V_2X4

2) ATX

3) CPU_FAN

4) SYS_FAN

5) LED_C

6) SATA3 2/3/4/5

7) M2A_SB

8) F_PANEL

9) F_AUDIO

10) F_U32

11) F_USB

12) COMA

13) SPI_TPM

14) CLR_CMOS

15) BAT

- 12 -

DEBUG

PORT

G.QBOFM

131

ATX

To meet expansion requirements, it is recommended that a power supply that can withstand high

power consumption be used (500W or greater). If a power supply is used that does not provide the

required power, the result can lead to an unstable or unbootable system.

ATX:

PinNo. Denition PinNo. Denition

1 3.3V 13 3.3V

2 3.3V 14 -12V

3GND 15 GND

4 +5V 16 PS_ON(softOn/Off)

5GND 17 GND

6 +5V 18 GND

7GND 19 GND

8 Power Good 20 NC

9 5VSB (stand by +5V) 21 +5V

10 +12V 22 +5V

11 +12V (Only for 2x12-pin

ATX)

23 +5V (Only for 2x12-pin ATX)

12 3.3V (Only for 2x12-pin

ATX)

24 GND(Onlyfor2x12-pinATX)

1/2) ATX_12V_2X4/ATX (2x4 12V Power Connector and 2x12 Main Power Connector)

With the use of the power connector, the power supply can supply enough stable power to all the components

onthemotherboard.Beforeconnectingthepowerconnector,rstmakesurethepowersupplyisturned

off and all devices are properly installed. The power connector possesses a foolproof design. Connect the

power supply cable to the power connector in the correct orientation.

The 12V power connector mainly supplies power to the CPU. If the 12V power connector is not connected,

the computer will not start.

ATX_12V_2X4:

PinNo. Denition PinNo. Denition

1GND(Onlyfor2x4-pin12V) 5+12V (Only for 2x4-pin 12V)

2GND(Onlyfor2x4-pin12V) 6+12V (Only for 2x4-pin 12V)

3GND 7 +12V

4GND 8 +12V

DEBUG

PORT

G.QBOFM

ATX_12V_2X4

3/4) CPU_FAN/SYS_FAN (Fan Headers)

All fan headers on this motherboard are 4-pin. Most fan headers possess a foolproof insertion design.

When connecting a fan cable, be sure to connect it in the correct orientation (the black connector wire is

the ground wire). The speed control function requires the use of a fan with fan speed control design. For

optimum heat dissipation, it is recommended that a system fan be installed inside the chassis.

•Be sure to connect fan cables to the fan headers to prevent your CPU and system from

overheating. Overheating may result in damage to the CPU or the system may hang.

•Thesefanheadersarenotcongurationjumperblocks.Donotplaceajumpercapontheheaders.

CPU_FAN

DEBUG

PORT

G.QBOFM

SYS_FAN

PinNo. Denition

1GND

2 Voltage Speed Control

3 Sense

4 PWM Speed Control

DEBUG

PORT

G.QBOFM

Connector CPU_FAN SYS_FAN

Maximum Current 2A 2A

Maximum Power 24W 24W

- 13 -

6) SATA3 2/3/4/5 (SATA 6Gb/s Connectors)

The SATA connectors conform to SATA 6Gb/s standard and are compatible with SATA 3Gb/s and SATA

1.5Gb/s standard. Each SATA connector supports a single SATA device. The Intel® ChipsetsupportsRAID0,

RAID1,RAID5,andRAID10.RefertoChapter3,"ConguringaRAIDSet,"forinstructionsonconguring

aRAIDarray.

PinNo. Denition

1GND

2 TXP

3TXN

4GND

5RXN

6RXP

7GND

SATA3

3 2

5 4

DEBUG

PORT

G.QBOFM

DEBUG

PORT

G.QBOFM

DEBUG

PORT

G.QBOFM

DEBUG

PORT

G.QBOFM

5) LED_C (RGB LED Strip Header)

 Theheadercanbeusedtoconnectastandard5050RGBLEDstrip(12V/G/R/B),withmaximumpower

rating of 2A (12V) and maximum length of 2m.

PinNo. Denition

1 12V

2 G

4 B

Before installing the devices, be sure to turn off the devices and your computer. Unplug the power

cord from the power outlet to prevent damage to the devices.

ConnectyourRGBLEDstriptotheheader.Thepowerpin(marked

withatriangleontheplug)oftheLEDstripmustbeconnectedtoPin

1 (12V) of this header. Incorrect connection may lead to the damage

oftheLEDstrip.

Forhowtoturnon/offthelightsoftheLEDstrippleasevisitthe"UniqueFeatures"webpageof

GIGABYTE's website.

DEBUG

PORT

G.QBOFM

RGBLEDStrip

12V

Toenablehot-pluggingfortheSATAports,refertoChapter2,"BIOSSetup,""Settings\IOPorts\

SATAAndRSTConguration,"formoreinformation.

- 14 -

7) M2A_SB (M.2 Socket 3 Connector)

 TheM.2connectorsupportsM.2SATASSDsandM.2PCIeSSDs.

F_USB30 F_U

B_ 

F_  F_ 



_

B

BS_

B

SB_

B

_S



S_

_

B

_U

_

B





 

S  

 

123

 

123

 

123

 

123

BSS

S

_S 

SSU

 

1 2 3  

 S3 BSSS



U

 __ 3

F_USB3F

S  _

SF





B_

F

_0

S

S

_0F

_F

_

_

__B





U

S  _S

_ SF_

B 

USB0_B

B_

B_

F_USB3

 F_USB303



_



_3U

S_

80 60 42

FollowthestepsbelowtocorrectlyinstallanM.2SSDintheM.2connector.

Step 1:

LocatethepropermountingholefortheM.2SSDtobeinstalledandtheninstallthemountingcliprst.

Step 2:

SlidetheM.2SSDintotheconnectoratanangle.

Step 3:

PresstheM.2SSDdownandthensecureitbypressingtheclippinintothemountinghole.

The front panel design may differ by chassis. A front panel module mainly consists of power switch,

resetswitch,powerLED,harddriveactivityLED,speakerandetc.Whenconnectingyourchassis

front panel module to this header, make sure the wire assignments and the pin assignments are

matched correctly.

8) F_PANEL (Front Panel Header)

Connect the power switch, reset switch, speaker, chassis intrusion switch/sensor and system status indicator

onthechassistothisheaderaccordingtothepinassignmentsbelow.Notethepositiveandnegativepins

before connecting the cables.

System Status LED

S0 On

S3/S4/S5 Off

•PW (Power Switch):

Connects to the power switch on the chassis front panel. You may

congure the way to turn off your system using thepower switch

(refertoChapter2,"BIOSSetup,""Settings\PlatformPower,"formore

information).

•SPEAK (Speaker):

Connects to the speaker on the chassis front panel. The system reports

system startup status by issuing a beep code. One single short beep

will be heard if no problem is detected at system startup.

•PLED/PWR_LED (PowerLED):

Connects to the power status indicator

onthechassisfrontpanel.TheLEDison

whenthesystemisoperating.TheLEDis

off when the system is in S3/S4 sleep state

or powered off (S5).

•HD (HardDriveActivityLED):

 ConnectstotheharddriveactivityLEDonthechassisfrontpanel.TheLEDisonwhentheharddrive

is reading or writing data.

•RES (ResetSwitch):

Connects to the reset switch on the chassis front panel. Press the reset switch to restart the computer

ifthecomputerfreezesandfailstoperformanormalrestart.

•CI (Chassis Intrusion Header):

Connects to the chassis intrusion switch/sensor on the chassis that can detect if the chassis cover has

been removed. This function requires a chassis with a chassis intrusion switch/sensor.

•NC: Noconnection.

PLED-

PW-

SPEAK+

SPEAK-

PLED+

PW+

HD-

RES+

HD+

RES-

HardDrive

ActivityLED

Reset

Switch

DEBUG

PORT

G.QBOFM

PowerLED

CI-

CI+

PowerLED

Chassis Intrusion

Header

Power Switch Speaker

PWR_LED-

PWR_LED+

- 15 -

9) F_AUDIO (Front Panel Audio Header)

 ThefrontpanelaudioheadersupportsHighDenitionaudio(HD).Youmayconnectyourchassisfront

panel audio module to this header. Make sure the wire assignments of the module connector match the

pin assignments of the motherboard header. Incorrect connection between the module connector and the

motherboard header will make the device unable to work or even damage it.

Some chassis provide a front panel audio module that has separated connectors on each wire instead

of a single plug. For information about connecting the front panel audio module that has different wire

assignments, please contact the chassis manufacturer.

PinNo. Denition PinNo. Denition

1 MIC2_L 6 Sense

2GND 7FAUDIO_JD

3MIC2_R 8NoPin

4NC 9LINE2_L

5LINE2_R 10 Sense

PinNo. Denition PinNo. Denition

1 VBUS 11 D2+

2SSRX1- 12 D2-

3SSRX1+ 13 GND

4GND 14 SSTX2+

5 SSTX1- 15 SSTX2-

6 SSTX1+ 16 GND

7GND 17 SSRX2+

8D1- 18 SSRX2-

9D1+ 19 VBUS

10 NC 20 NoPin

10) F_U32 (USB 3.2 Gen 1 Header)

 TheheaderconformstoUSB3.2Gen1andUSB2.0specicationandcanprovidetwoUSBports.For

purchasingtheoptional3.5"frontpanelthatprovidestwoUSB3.2Gen1ports,pleasecontactthelocal

dealer.

F_USB30 F_U

B_ 

F_  F_ 



_

B

BS_

B

SB_

B

_S



S_

_

B

_U

_

B





 

S  

 

123

 

123

 

123

 

123

BSS

S

_S 

SSU

 

1 2 3  

 S3 BSSS



U

 __ 3

F_USB3F

S  _

SF





B_

F

_0

S

S

_0F

_F

_

_

__B





U

S  _S

_ SF_

B 

USB0_B

B_

B_

F_USB3

 F_USB303



_



_3U

S_

20 1

11) F_USB (USB 2.0/1.1 Header)

 TheheaderconformstoUSB2.0/1.1specication.EachUSBheadercanprovidetwoUSBportsviaan

optional USB bracket. For purchasing the optional USB bracket, please contact the local dealer.

PinNo. Denition PinNo. Denition

1 Power (5V) 6 USBDY+

2 Power (5V) 7 GND

3USBDX- 8GND

4USBDY- 9NoPin

5USBDX+ 10 NC

•DonotplugtheIEEE1394bracket(2x5-pin)cableintotheUSB2.0/1.1header.

•Prior to installing the USB bracket, be sure to turn off your computer and unplug the power cord

from the power outlet to prevent damage to the USB bracket.

- 16 -

12) COMA (Serial Port Header)

The COM header can provide one serial port via an optional COM port cable. For purchasing the optional

COM port cable, please contact the local dealer.

PinNo. Denition PinNo. Denition

1NDCD- 6NDSR-

2NSIN 7NRTS-

3NSOUT 8NCTS-

4NDTR- 9NRI-

5GND 10 NoPin

13) SPI_TPM (Trusted Platform Module Header)

You may connect an SPI TPM (Trusted Platform Module) to this header.

PinNo. Denition PinNo. Denition

1DataOutput 7Chip Select

2Power (3.3V) 8GND

3NoPin 9IRQ

4NC 10 NC

5DataInput 11 NC

6CLK 12 RST

F_USB30 F_U

B_ 

F_  F_ 



_

B

BS_

B

SB_

B

_S



S_

_

B

_U

_

B





 

S  

 

123

 

123

 

123

 

123

BSS

S

_S 

SSU

 

1 2 3  

 S3 BSSS



U

 __ 3

F_USB3F

S  _

SF





B_

F

_0

S

S

_0F

_F

_

_

__B





U

S  _S

_ SF_

B 

USB0_B

B_

B_

F_USB3

 F_USB303



_



_3U

S_

14) CLR_CMOS (Clear CMOS Jumper)

 UsethisjumpertocleartheBIOScongurationandresettheCMOSvaluestofactorydefaults.Toclear

the CMOS values, use a metal object like a screwdriver to touch the two pins for a few seconds.

•Always turn off your computer and unplug the power cord from the power outlet before clearing

the CMOS values.

•Aftersystemrestart,gotoBIOSSetuptoloadfactorydefaults(selectLoadOptimizedDefaults)or

manuallyconguretheBIOSsettings(refertoChapter2,"BIOSSetup,"forBIOScongurations).

Open:Normal

Short: Clear CMOS Values

- 17 -

15) BAT (Battery)

 Thebatteryprovidespowertokeepthevalues(suchasBIOScongurations,date,andtimeinformation)

intheCMOSwhenthecomputeristurnedoff.Replacethebatterywhenthebatteryvoltagedropstoalow

level, or the CMOS values may not be accurate or may be lost.

You may clear the CMOS values by removing the battery:

1. Turn off your computer and unplug the power cord.

2. Gently remove the battery from the battery holder and wait for one minute. (Or use a

metal object like a screwdriver to touch the positive and negative terminals of the battery

holder, making them short for 5 seconds.)

3. Replacethebattery.

4. Plug in the power cord and restart your computer.

•Always turn off your computer and unplug the power cord before replacing the battery.

•Replacethebatterywithanequivalentone.Damagetoyourdevicesmayoccurifthebatteryis

replaced with an incorrect model.

•Contact the place of purchase or local dealer if you are not able to replace the battery by yourself

or uncertain about the battery model.

•When installing the battery, note the orientation of the positive side (+) and the negative side (-)

of the battery (the positive side should face up).

•Used batteries must be handled in accordance with local environmental regulations.

- 18 -

BIOS (Basic Input and Output System) records hardware parameters of the system in the CMOS on the

motherboard. Its major functions include conducting the Power-On Self-Test (POST) during system startup,

saving system parameters and loading operating system, etc. BIOS includes a BIOS Setup program that allows

theusertomodifybasicsystemcongurationsettingsortoactivatecertainsystemfeatures.

When the power is turned off, the battery on the motherboard supplies the necessary power to the CMOS to

keepthecongurationvaluesintheCMOS.

ToaccesstheBIOSSetupprogram,pressthe<Delete>keyduringthePOSTwhenthepoweristurnedon.

ToupgradetheBIOS,useeithertheGIGABYTEQ-Flashor@BIOSutility.

•Q-Flash allows the user to quickly and easily upgrade or back up BIOS without entering the operating system.

•@BIOSisaWindows-basedutilitythatsearchesanddownloadsthelatestversionofBIOSfromtheInternet

and updates the BIOS.

Chapter 2 BIOS Setup

•BecauseBIOSashingispotentiallyrisky,ifyoudonotencounterproblemsusingthecurrent

versionofBIOS,itisrecommendedthatyounotashtheBIOS.ToashtheBIOS,doitwith

caution.InadequateBIOSashingmayresultinsystemmalfunction.

•It is recommended that you not alter the default settings (unless you need to) to prevent system

instability or other unexpected results. Inadequately altering the settings may result in system's

failure to boot. If this occurs, try to clear the CMOS values and reset the board to default values.

(Refertothe"LoadOptimizedDefaults"sectioninthischapterorintroductionsofthebattery/clear

CMOS jumper in Chapter 1 for how to clear the CMOS values.)

2-1 Startup Screen

The following startup Logo screen will appear when the computer boots.

Function Keys

•When the system is not stable as usual, select the Load Optimized Defaults item to set your system to its defaults.

•The BIOS Setup menus described in this chapter are for reference only and may differ by BIOS version.

TherearetwodifferentBIOSmodesasfollowsandyoucanusethe<F2>keytoswitchbetweenthetwomodes.

Easy Mode allows users to quickly view their current system information or to make adjustments for optimum

performance.InEasyMode,youcanuseyourmousetomovethroughcongurationitems.TheAdvancedMode

provides detailed BIOS settings. You can press the arrow keys on your keyboard to move among the items

andpress<Enter>toacceptorenterasub-menu.Oryoucanuseyourmousetoselecttheitemyouwant.

- 19 -

2-2 The Main Menu

Hardware

Information

OptionDescription Current Settings

Setup Menus

Conguration

Items

System

Time

Quick Access Bar allows you to quickly move to

the General Help, Easy Mode, Smart Fan 5, or

Q-Flash screen.

Advanced Mode Function Keys

<f><g>Move the selection bar to select a setup menu

<h><i> Movetheselectionbartoselectancongurationitemonamenu

<Enter>/DoubleClick Execute command or enter a menu

<+>/<PageUp> Increase the numeric value or make changes

<->/<PageDown> Decreasethenumericvalueormakechanges

<F1> Show descriptions of the function keys

<F2> Switch to Easy Mode

<F3> SavethecurrentBIOSsettingstoaprole

<F4> LoadtheBIOSsettingsfromaprolecreatedbefore

<F5> RestorethepreviousBIOSsettingsforthecurrentsubmenus

<F6> DisplaytheSmartFan5screen

<F7> LoadtheOptimizedBIOSdefaultsettingsforthecurrentsubmenus

<F8> Access the Q-Flash utility

<F10> Save all the changes and exit the BIOS Setup program

<F11> Switch to the Favorites submenu

<F12> Capture the current screen as an image and save it to your USB drive

<Insert> Add or remove a favorite option

<Ctrl>+<S> Displayinformationontheinstalledmemory

<Esc> Main Menu: Exit the BIOS Setup program

Submenus: Exit current submenu

- 20 -

Page is loading ...

GIGA-BYTE TECHNOLOGY H410M DS2V V2 User manual

Brand: GIGA-BYTE TECHNOLOGY

Model: H410M DS2V V2

Type: User manual

This manual is also suitable for

H410M S2 V2

Download PDF

report

in other languages

italiano: GIGA-BYTE TECHNOLOGY H410M DS2V V2 Manuale utente

GIGA-BYTE TECHNOLOGY H410M DS2V V2 User manual

This manual is also suitable for

GIGA-BYTE TECHNOLOGY H410M DS2V V2 User manual

in other languages

Other documents