AZ Patio Heaters WLF-HEX User manual

Brand: AZ Patio Heaters

Model: WLF-HEX

Category: Fireplaces

Type: User manual

MODEL #

ANS Z 21.97-2010, Outdoor Decorative Gas Appliances

CGA CR 97-003 Outdoor Gas Fireplaces

GS-F-PC

GS-F-PCSS

OUTDOOR

FIRE PIT

Questions, problems, missing parts? Before returning to your retailer, call our customer

service department at 1-888-775-1330, 7 a.m. - 4 p.m., PST, Monday - Friday.

PACKAGE CONTENTS

NOITPIRCSED TRAP QUANTITY

Cover

Burner Assembly

1/4 Table

Angle Iron

Door Bracket

Gas Cylinder Block Belt

Bottom plate

Back Bracket Post (Left)

G Front Bracket Post (Left)

Back Bracket Post (Right)

Front Bracket Post (Right)

Side Panel

Door (Left)

Door Handle

Door (Right)

O I

HARDWARE CONTENTS (shown actual size)

DD EE

GG HH II

Screw

M4 X 8

Qty. 5

Bolt

M6 X 12

Qty. 40

Knob

Qty. 1

Screw

M5 X 8

Qty. 4

Bolt

M6 X 30

Qty. 4

washer Φ4

Qty. 4

Wrench

Qty. 1

M6 nut

Qty. 8

SAFETY INFORMATION

Solid fuels shall hot be burned in this appliance.

This appliance has been tested to and complies with the ANS Z 21.97-2010, Outdoor Decorative

Gas Appliances CGA CR 97-003 Outdoor Gas Fireplaces. The installation must conform to local

codes or the absence of local codes to the National Fuel Gas Code. ANS Z223.1.This manual

contains important information about the assembly, operation and maintenance of this fire pit. General

safety information is presented in these first few pages and is also located throughout the manual.

Keep this manual for future reference and to educate new users of this product. This manual should

be read in conjunction with the labeling on the product. Safety precautions are essential when any

mechanical or propane fueled equipment is involved. These precautions are necessary when using,

storing, and servicing. Using this equipment with the respect and caution demanded will reduce the

possibilities of personal injury or property damage. The following symbols shown below are used

extensively throughout this manual. Always heed these precautions, as they are essential when using

any mechanical or fueled equipment.

DANGER

DANGER indicates an imminently hazardous situation

which, if not avoided, will result in death or serious injury.

FOR YOUR SAFETY

If you smell gas:

1. Shut off gas to the appliance.

2. Extinguish any open flame.

3. If odor continues, keep away from the appliance and

immediately call you gas supplier or fire department.

DANGER

Failure to comply with the precautions and instructions

provided with this fire pit can result in death, serious

bodily injury and property loss or damage from

hazards of fire, explosion, burn, asphyxiation, and/or

carbon monoxide poisoning. Only persons who can

understand and follow the instructions should use or

service this fire pit.

Propane

Tank Strap

Qty. 1

Glass

(One Pack)

Qty. 1

Door Handle

Qty. 2

Please read and understand this entire manual before attempting to assemble, operate or install

the product. If you have any questions regarding the product, please call customer service at

1-888-775-1330, 7 a.m. - 4 p.m., PST, Monday - Friday.

SAFETY INFORMATION

DANGER

• CARBON MONOXIDE HAZARD

• This fire pit is a combustion appliance. All combustion

appliances produce carbon monoxide (CO) during the

combustion process. This product is designed to produce

extremely minute, non-hazardous amounts of CO if used

and maintained in accordance with all warnings and

instructions. Do not block air flow into or out of the fire pit.

• Carbon Monoxide (CO) poisoning produces flu-like

symptoms, watery eyes, headaches, dizziness, fatigue

and possibly death. You can't see it and you can't

smell it. It's an invisible killer. If these symptoms are

present during operation of this product get fresh air

immediately!

• For outdoor use only.

• Never use inside house, or other unventilated or

enclosed areas.

• This fire pit consumes air (oxygen). Do not use in

unventilated or enclosed areas to avoid endangering

your life.

WARNING

DANGER

• EXPLOSION - FIRE HAZARD

• Keep solid combustibles, such as building materials,

paper or cardboard, a safe distance away from the

fire pit as recommended by the instructions.

• Provide adequate clearances around air openings

into the combustion chamber.

• Never use the fire pit in spaces which do or may

contain volatile or airborne combustibles, or products

such as gasoline, solvents, paint thinner, dust particles

or unknown chemicals.

• During operation, this product can be a source of

ignition. Keep fire pit area clear and free from

combustible materials, gasoline, paint thinner, cleaning

solvents and other flammable vapors and liquids. Do

not use fire pit in areas with high dust content.

Minimum fire pit clearances from combustible

materials: two (2) feet from the sides & two (2) feet

from the rear, 6 feet from ceiling.

We cannot foresee every use which may be made of

our fire pit.

Check with your local fire safety authority if you have

questions about fire pit use.

Other standards govern the use of fuel gases and heat

producing products for specific uses. Your local

authorities can advise you about these.

If no local codes exist, follow National Fuel Gas Code,

ANS Z223.1. In Canada, installation must conform to

local codes. If no local codes exist, follow the current

National standards of CANADA CAN/CGA-B 149.2.

DANGER

WARNING

Do not store or use gasoline or other flammable vapors

and liquids in the vicinity of this or any other appliance.

An LP-cylinder not connected for use shall not be

stored in the vicinity of this or any other appliance.

WARNING

Improper installation, adjustment, alteration, service or

maintenance can cause property damage, injury or

death. Read the installation, operation and

maintenance instructions thoroughly before installing

or servicing this equipment.

CARBON MONOXIDE HAZARD

This appliance can produce

carbon monoxide which has

no odor. Using it in an enclosed

space can kill you. Never use this

appliance in an enclosed space

such as a camper, tent or home.

WARNING: For Outdoor Use Only

DANGER

• EXPLOSION - FIRE HAZARD

• Never store propane near high heat, open flames,

pilot lights, direct sunlight, other ignition sources or

where temperatures exceed 120 degrees F (49°C).

• Propane vapors are heavier than air and can

accumulate in low places. If you smell gas, leave the

area immediately.

• Never install or remove propane cylinder while fire pit

is lighted, near flame, pilot lights, other ignition sources

or while fire pit is hot to touch.

• This fire pit is red hot during use and can ignite

flammables too close to the burner. Keep flammables

at least 2 feet from sides & 2 feet from rear, 6 feet

from ceiling. Keep gasoline and other flammable liquids

and vapors well away from fire pit.

• Store the propane cylinder outdoors in a well ventilated

space out of reach of children. Never store the propane

cylinder in an enclosed area (house, garage, etc.). If

fire pit is to be stored indoors, disconnect the propane

cylinder for outdoor storage.

WARNING

WARNING indicates an imminently hazardous situation

which, if not avoided, will result in death or serious injury.

PREPARATION

Before beginning assembly of product, make sure all parts are present. Compare parts with

package contents list and hardware contents above. If any part is missing or damaged, do not

attempt to assemble the product. Contact customer service for replacement parts.

Estimated Assembly Time: 60 minutes

Tools Required for Assembly (not included):

Phillips screwdriver w/ medium blade. Leak Detection Solution.

WARNING

California Proposition 65

Combustion by-products produced when using

this product contain chemicals known to the State

of California to cause cancer, birth defects, and

other reproductive harm.

WARNING

BURN HAZARD

• Never leave fire pit unattended when hot or in use.

• Keep out of reach of children.

WARNING

• This product is fueled by propane gas. Propane gas

is invisible, odorless, and flammable. An odorant is

normally added to help detect leaks and can be

described as a “rotten egg” smell. The odorant can

fade over time so leaking gas is not always detectable

by smell alone.

• Propane gas is heavier than air and leaking propane

will sink to the lowest level possible. It can ignite by

ignition sources including matches, lighters, sparks or

open flames of any kind many feet away from the

original leak. Use only propane gas set up for vapor

withdrawal.

• Store or use propane gas in compliance with local

ordinances and codes or with ANS/NFPA 58. Turn off

propane when not in use.

WARNING

• Alert children and adults to the hazards of high surface

temperatures. Stay away from these surfaces to avoid

burning skin or igniting clothing.

• Carefully supervise young children when in the vicinity

of the fire pit.

• Do not hang clothing or any other flammable materials

from the fire pit, or place on or near the fire pit.

• Replace any guard or protective device removed for

servicing the appliance prior to placing back in service.

• Installation and repair should be done by a qualified

service person. The fire pit should be inspected

before use and annually by a qualified service person.

More frequent cleaning may be required as necessary.

It is imperative that the control compartment, burners,

and circulating air passageway of the appliance be

kept clean.

SAFETY INFORMATION

CAUTION

CAUTION indicates an imminently hazardous situation

which, if not avoided, may result in minor or moderate

personal injury, or property damage.

CAUTION

SERVICE SAFETY

• Keep all connections and fittings clean. Make sure

propane cylinder valve outlet is clean.

• During set up, check all connections and fittings for

leaks using soapy water. Never use a flame.

• Use as a heating appliance only. Never alter in any

way or use with any device.

WARNING

Certain materials or items, when stored under the

fire pit, will be subjected to radiant heat and could be

seriously damaged.

ASSEMBLY INSTRUCTIONS

Hardware Used

1. Attached a door handle (N) to one door (left) (M) with

two Φ4 washers (AA) and two M4 X 8 screws (BB).

Repeat procedure to complete the assembly of the other

door (right) (O).

2. Attach a angle iron (D) to 1/4 table (C) with M6 X 12

bolt (EE). Repeat procedure to complete the assembly of

the rest of three 1/4 tables.

3. Line up holes in 1/4 table with corresponding holes

the other 1/4 table, insert two M6 X 12 bolts (EE) through

holes, finger tighten two M6 nuts (DD) . Be sure that line

① and line ② are in the same level and fully tighten

bolts. Use another two M6 X 12 bolts to fasten the two

1/4 tables. Repeat procedure to complete the assembly of

the rest of 1/4 tables.

x 4

Screw M4 X 8

Washer Φ4

x 4

Bolt M6 X 12

Hardware Used

x 12

Bolt M6 X 12

x 8

Nut M6

ASSEMBLY INSTRUCTIONS

5-1

5-2

4. Attach propane tank strap (HH) to bottom plate (L) like

the figure 4 show.

5. Bracket Post Installation.

5-1. Attached four bracket posts to the bottom plate with

four M6 X 30 bolts (CC) like figure 5-1 show.

5-2. After assembly the bracket posts and gas cylinder

block belt (K) with two M6 X 12 bolts (EE),the assembly

parts like the figure 5-2 show.

Hardware Used

x 1

Propane tank strap

Hardware Used

x 4

Bolt M6 X 30

Hardware Used

x 2

Bolt M6 X 12

ASSEMBLY INSTRUCTIONS

6-1

6. Door Installation.

6-1. Attach two doors like figure 6-1 shows. Put door

bracket (E) above two doors, fasten the door bracket

with two M6 X 12 bolts (EE).

6-2. Do not put door bracket too close to the doors

to ensure two doors can open easily.

Hardware Used

7. Side panel (J) Installation.

7-1. Attached three side panels to the bracket posts

with 12 M6 X 12 bolts (EE).

7-1

6-2

Hardware Used

x 2

Bolt M6 X 12

x 12

Bolt M6 X 12

ASSEMBLY INSTRUCTIONS

7-2

8-1

7-2. After assembly, the base assembly will like

figure 7-2 shows.

8. Table Installation

8-1.Line up holes in assembled table with

corresponding holes in base assembly, insert eight

M6 X 12 bolts (EE) through holes, tighen them.

8-2. After assembly, the assembly part will like

figure 8-2 shows.

8-2

Hardware Used

x 8

Bolt M6 X 12

Base assembly

ASSEMBLY INSTRUCTIONS

9-1

9-2

9. Burner Installation

9-1. Line up holes in the burner assembly (B) with

corresponding holes in the table assembly, insert four

M5X8 screws (FF) through holes, fasten them.

9-2.The total assembly parts will like the figure 9-2

shows.

10-1. Screw the knob (P) on the cover (A) with M4 X 8

screws (BB). Put glass (one pack) (II) above the burner

and put the cover above the burner assembly.

10-1

Hardware Used

x 4

Screw M5X8

Hardware Used

x 1

Knob

Screw M4 X 8

x 1

ASSEMBLY INSTRUCTIONS

10-2

10-2. Total fire pit installation complete.

11. Connect hose and regulator to cylinder.

The propane gas and cylinder are sold separately.

Use a standard 20 lb. propane cylinder only.

Use this heater only with a propane vapor withdrawal

supply system. See chapter 5 of the standard for

storage and handling of liquefied petroleum gas,

ANS/NFPA 58. Your local library or fire department

should have this book.

Storage of an appliance indoors is permissible only if

the cylinder is disconnected and removed from the

appliance. A cylinder must be stored outdoors in a

well-ventilated area out of the reach of children. A

disconnected cylinder must have dust caps tightly

installed and must not be stored in a building, garage or

any other enclosed area. The maximum inlet gas supply

pressure: 250 psi, The minimum inlet gas supply

pressure: 5 psi.

The minimum hourly of 10000 Btu is required input

rating for a heater for automatic operation at ratings less

than full input rating.

The pressure regulator and hose assembly supplied

with the appliance must be used.

The installation must conform with local codes, or in the

absence of local codes,with national fuel gas code,

ANS Z223.1/NFPA54, natural gas and propane

Installation Code, CSA B149.1, or propane storage and

handling code, B149.2.

Standard 20 lb. tank

ASSEMBLY INSTRUCTIONS

A dented, rusted or damaged propane cylinder may be

hazardous and should be checked by your cylinder

supplier. Never use a propane cylinder with a damaged

valve connection.

The propane cylinder must be constructed and marked

in accordance with the specifications for LP gas

cylinders of the U.S. Department of Transportation

(DOT) or the standard for cylinders, spheres and

tubes for transportation of dangerous goods and

commission, CAN/CSA-B339.

The cylinder must have a listed overfilling prevention

device.

The cylinder must have a connection device compatible

with the connection for the appliance.

The cylinder used must include a collar to protect the

cylinder valve.

Never connect an unregulated propane cylinder to the

heater.

Attach regulator to cylinder. Complete attachment.

Install cylinder.

Do not store a spare LP-gas cylinder under or near this appliance;

Never fill the cylinder beyond 80 percent full;

Place the dust cap on the cylinder valve outlet whenever the cylinder is not

in use. Only install the type of dust cap on the cylinder valve that is provided with

the cylinder valve. Other type of caps or plugs may result in leakage of propane.

ATTENTION: THIS PRODUCT IS NOT FOR COMMERCIAL USE INTENDED

FOR RESIDENTIAL USE ONLY.

Do not sit or stand on this table .

Keep children away during assembly, This item contains small parts which can be

swallowed by children.

Do not use indoors and inside any enclosure.

Retain the assembly instruction for future reference.

Installer – Please leave these instruction with the owner.

Please quote following FQC NO. when contacting service center.

OPERATION INSTRUCTIONS

Leak Check

1. Make 2-3 oz. of leak check solution (one part liquid dishwashing detergent and three parts water).

2. Apply several drops of solution where hose attaches to regulator.

3. Apply several drops of solution where regulator connects to cylinder.

4. Make sure all fire pit and light valves are OFF.

5. Turn cylinder valve ON.

If bubbles appear at any connection, there is a leak.

1. Turn cylinder valve OFF.

2. If leak is at hose/regulator connection: tighten connection and perform another leak test. If bubbles

continue appearing, the hose should be returned to the place of purchase.

3. If leak is at regulator/cylinder valve connection: disconnect, reconnect, and perform another leak

check. If you continue to see bubbles after several attempts, cylinder valve is defective and should be

returned to cylinder’s place of purchase.

If NO bubbles appear at any connection, the connections are secure.

NOTE: Whenever gas connections are loosened or removed, you must perform a complete leak test.

Complete installation.

Regulator / Cylinder

connection

Hose / Regulator

connection

WARNING

• Perform all leak tests outdoors.

• Extinguish all open flames.

• NEVER leak test when smoking.

• Do not use the fire pit until all connections have been

leak tested and do not leak.

OPERATION INSTRUCTIONS

DANGER

• CARBON MONOXIDE HAZARD

• For outdoor use only. Never use inside house, or other

unventilated or enclosed areas. This fire pit consumes air

(oxygen). Do not use in unventilated or enclosed areas to

avoid endangering your life.

Before Turning Gas Supply ON:

1. Your fire pit was designed and approved for outdoor use only. Do NOT use it inside a building,

garage, or any other enclosed area.

2. Make sure surrounding areas are free of combustible materials, gasoline, and other flammable

vapors or liquids.

3. Ensure that there is no obstruction to air ventilation. Be sure all gas connections are tight and

there are no leaks.

4. Be sure the cylinder cover is clear of debris. Be sure any component removed during assembly

or servicing is replaced and fastened prior to starting.

Before Lighting:

1. Fire pit should be thoroughly inspected before each use, and by a qualified service person at least

annually. If relighting a hot fire pit, always wait at least 5 minutes.

2. Inspect the hose assembly for evidence of excessive abrasion, cuts, or wear. Suspected areas

should be leak tested. If the hose leaks, it must be replaced prior to operation. Only use the

replacement hose assembly specified by manufacturer.

Lighting:

1) Turn the control knob to the “OFF” position (Figure a).

2) Fully open LP cylinder valve.

Note: For initial start or after any cylinder change, hold Control Knob IN for

2 minutes to purge air from gas lines before proceeding.

3) Push in gas control knob and turn counterclockwise to “IGNITER”

(Figure b) to light the fire pit. If needed, keep depressing and turning control knob

counterclockwise until the heater lights (You should hear a clicking sound).

4) After fire pit lights, release control knob. Push in and turn the control knob to the “HIGH”, then

release control knob. If you want a lower temperature, push in the control knob and turn

counterclockwise to the “LOW” (Figure c).

Note: If burner fails to remain lit, all valves should be closed and a waiting period of at least 5

minutes should pass before attempting to light.

Caution: Do not attempt to operate until you have read and understand all General Safety Information

in this manual and all assembly is complete and leak checks have been performed.

Figure a

Figure b

Figure c

in.

Normal Abnormal

Very hot while in a operation!

Never lean over the fireplace while in use.

Do not touch tile of spark guard while the fire pit is in

operation, wait until the fire pit has cooled down after use.

Failure to comply with these instructions may result in

serious bodily injury.

WARNING

OPERATION INSTRUCTIONS

Shut Down:

1. To extinguish burner depress control knob and continue to turn it clockwise to OFF.

2. Turn cylinder valve clockwise to OFF and disconnect regulator when heater is not in use.

Operation Checklist

For a safe and pleasurable heating experience, perform this check before each use.

Before Operating:

1. I am familiar with entire owner’s manual and understand all precautions noted.

2. All components are properly assembled, intact and operable.

3. No alterations have been made.

4. All gas connections are secure and do not leak.

5. Wind velocity is below 10 mph.

6. Unit will operate at reduced efficiency below 40°F.

7. Fire pit is outdoors (outside any enclosure).

8. There is adequate fresh air ventilation.

When fire pit is ON:

Burner will display tongues of blue and yellow flame. These flames should not be yellow or produce thick

black smoke, indicating an obstruction of airflow through the burners. The flame should be blue with

straight yellow tops. If excessive yellow flame is detected, turn off heater and consult “Troubleshooting”

on page 18.

Re-lighting:

1. Turn control knob to OFF.

2. Repeat the “Lighting” steps on prior page.

WARNING

FOR YOUR SAFETY

Be careful when attempting to manually ignite this

fire pit. Holding in the control know for more than 10

seconds before igniting the gas will cause a ball of

flame upon ignition.

WARNING

FOR YOUR SAFETY

Fire pit will be hot after use. Handle with extreme care.

OPERATION INSTRUCTIONS

CARE AND MAINTENANCE

9. Fire pit is away from gasoline or other flammable liquids or vapors.

10. Fire pit is away from windows, air intake openings, sprinklers and other water sources.

11. Fire pit is at least 24 in. on rear and at least 24 in. on sides from combustible materials.

12. Fire pit is on a hard and level surface.

13. There are no signs of spider or insect nests.

14. All burner passages are clear.

15. All air circulation passages are clear.

16. Children and adults should be alerted to the hazards of high surface temperatures and should stay

away to avoid burns or clothing ignition.

17. Young children should be carefully supervised when they are in the area of the fire pit.

18. Clothing or other protective material should not be hung from the fire pit, or placed on or near the

fire pit.

19. Any guard or other protective device removed for servicing the fire pit must be replaced prior to

operating the fire pit.

20. Installation and repair should be done by a qualified service person. The fire pit should be inspected

before use and at least annually by a qualified service person.

21. More frequent cleaning may be required as necessary. It is imperative that control compartment,

burner and circulating air passageways of the fire pit be kept clean.

After Operation

1. Gas control is in OFF position.

2. Gas Tank valve is OFF.

3. Disconnect Gas line.

WARNING

FOR YOUR SAFETY:

• Do NOT touch or move fire pit for at least 45 minutes

after use.

• Reflector is hot to the touch.

• Allow reflector to cool before touching.

To enjoy years of outstanding performance from your fire pit, make sure you perform the following

maintenance activities on a regular basis:

Keep exterior surfaces clean.

1. Use warm soapy water for cleaning. Never use flammable or corrosive cleaning agents.

2. While cleaning your unit, be sure to keep the area around the burner dry at all times. Do not submerge

the control valve assembly. If the gas control is submerged in water, do NOT use it. It must be replaced.

a. Keep the appliance area clear and free from combustible materials, gasoline and other

flammable vapors and liquids.

b. Do not obstruct the flow of combustion and ventilation air.

c. Keep the ventilation opening(s) of the cylinder enclosure free and clear from debris.

3. Air flow must be unobstructed. Keep controls, burner, and circulating air passageways clean. Signs

of possible blockage include:

CARE AND MAINTENANCE

Gas odor with extreme yellow tipping of flame.

Fire pit does NOT reach the desired temperature.

Fire pit glow is excessively uneven.

Fire pit makes popping noises.

Spiders and insects can nest in burner or orifices. This dangerous condition can damage fire pit and

render it unsafe for use. Clean burner holes by using a heavy-duty pipe cleaner. Compressed air may

help clear away smaller particles.

Carbon deposits may create a fire hazard. Clean dome and burner screen with warm soapy water if

any carbon deposits develop.

Note: In a salt-air environment (such as near an ocean), corrosion occurs more quickly than normal.

Frequently check for corroded areas and repair them promptly.

TIP:

Use high-quality automobile wax to help maintain the appearance of

your fire pit. Apply to exterior surfaces from the pole down. Do not

apply to emitter screen or domes.

Storage

Between uses:

Turn Control Knob OFF.

Disconnect LP source.

Store fire pit upright in an area sheltered from direct contact with inclement weather (such as rain,

sleet, hail, snow, dust and debris).

If desired, cover fire pit to protect exterior surfaces and to help prevent build-up in air passages.

Note: Wait until fire pit is cool before covering.

During periods of extended inactivity or when transporting:

Turn Control Knob OFF.

Disconnect LP source and move to a secure, well-ventilated location outdoors.

Store fire pit upright in an area sheltered from direct contact with inclement weather (such as rain,

sleet, hail, snow, dust and debris).

If desired, cover fire pit to protect exterior surfaces and to help prevent build-up in air passages.

Never leave LP cylinder exposed to direct sunlight or excessive heat.

Note: Wait until fire pit is cool before covering.

Service

Only a qualified service person should repair gas passages and associated components.

Caution: Always allow fire pit to cool before attempting service.

TROUBLESHOOTING

PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION

Burner won’t light

Burner flame is low

Carbon build-up

Thick black smoke

Propane cylinder is frosted over

Blockage in orifice

Control knob is not in ON position

Gas pressure is low

Control knob fully ON

Dirt or film on reflector and burner screen

Blockage in burner

Remove blockage and clean burner

inside and outside

Check burner and orifices for

blockage

Clean reflector and burner screen

Outdoor temperature is less than 40ºF and

tank is less than 1/4 full

Turn cylinder valve OFF and replace

cylinder

Use a full cylinder

Turn control knob to ON

Wait until the propane cylinder

warms up and becomes unfrosted

Clear blockage

If you have any questions regarding the product, please call customer service at 1-888-775-1330,

7 a.m. - 4 p.m. (PST), Monday - Friday.

ONE-YEAR LIMITED WARRANTY

CUSTOMERS IN USA

Do not return this product to the store where you purchased it. Please call 1-888-775-1330

for assistance.

CUSTOMERS IN CANADA

IMPORTANT

Only return this product to the store if it was purchased within 90 days. If you have problems

after 90 days of purchase, please CALL 1-888-775-1330 DATED PROOF OF PURCHASE

REQUIRED FOR WARRANTY SERVICE.

This product is inspected, tested and carefully packaged to minimize the chance of damage

during shipment. If a part (excluding light bulbs and fuses*) within one year from the date of

purchase proves to be defective in material or fabrication under normal use, the part will be

repaired or replaced. The Company's obligation under the warranty is to replace or repair

defective parts at our discretion. Any expenses or damage resulting from the installation,

removal or transportation of the product will the responsibility of the owner and are not

covered by this warranty. The owner assumes all other risks arising out from the use or

misuse of the product. The warranty will be void if the product damage or failure is deemed

by the Company to be caused by accident, alteration, misuse, abuse, incorrect installation or

removal, or connection to an incorrect power source by the owner. The Company neither

assumes, nor authorizes any person or entity to assume for it any obligation or liability

associated with its products.

* Light bulbs and fuses are not covered under this warranty.

If you have any questions regarding the warranty or service, please call our toll

free number: 1-888-775-1330.

Distributed by:

AZ Patio Heaters, LLC

Toll Free Number 1-888-775-1330

Sales Service and Repair

www.azpatioheaters.com

Manufactured by:

Jiangsu Gardensun Furnace Co., Ltd.

No. 1, Boyi Town, Changzhou City,

Jiangsu Province P.R. China

REPLACEMENT PARTS LIST

Printed in China

NOITPIRCSED TRAP QUANTITY

Cover

Burner Assembly

1/4 Table

Angle Iron

Door Bracket

Gas Cylinder Block Belt

Bottom plate

Back Bracket Post (Left)

G Front Bracket Post (Left)

Back Bracket Post (Right)

Front Bracket Post (Right)

Side Panel

Door (Left)

Door Handle

Door (Right)

O I

For replacement parts, call our customer service department at 1-888-775-1330,

7 a.m. - 4 p.m., EST, Monday - Friday.

AZ Patio Heaters WLF-HEX User manual

Brand: AZ Patio Heaters

Model: WLF-HEX

Category: Fireplaces

Type: User manual

Download PDF

report

AZ Patio Heaters WLF-HEX User manual

AZ Patio Heaters WLF-HEX User manual

Related papers

Other documents