HP (Hewlett-Packard) All in One Printer 2600 User manual

Brand: HP (Hewlett-Packard)

Model: All in One Printer 2600

Type: User manual

This manual is also suitable for

2600
2700

HP Photosmart 2600/2700 series all-in-one

User Guide

HP Photosmart 2600/2700 series all-in-one

User Guide

Ң䖭䞠ᓔྟ

བᵰ೼ᅝ㺙ᳳ䯈䘛ࠄ䯂乬ˈ䇋খ䯙ᴀᣛफৢ䴶ⱘ⭥䲒ᥦ㾷Ǆ

a পϟ᠔᳝ⱘ㛊ᏺǄЎњ㦋ᕫ᳔Շᰒ⼎ᬜᵰˈ䇋পϟ

ᔽ㡆೒ᔶᰒ⼎ሣϞⱘֱᡸ㝰Ǆ

b ᢀ䍋ᰒ⼎ሣǄ

পϟ᠔᳝ⱘ㛊ᏺ੠ᢀ䍋ᰒ⼎ሣ

HP Photosmart 3100 All-in-One series Setup Guide

⊼ᛣ˖䰸䴲ᴀᣛफᣛ⼎ৃҹ䖲᥹USB⬉㓚ˈ৺߭ϡ㽕Փ⫼䖭㉏⬉㓚ˈҹ

ܡ᮴⊩ℷ⹂ᅝ㺙䕃ӊǄ

ᶹᡒ㒘ӊ

1 Windows CD

2 Macintosh CD

3 Փ⫼᠟ݠ

4 ⬉⑤㒓

5 4 x 6㣅ᇌ10 x 15 cm✻⠛㒌

6๼Ⲧ

7 ⬉䆱㒓

8 USB⬉㓚

9 ᥻ࠊ䴶ᵓ䌈⠛˄ৃ㛑Ꮖ乘ᅝ㺙˅

 ࣙ㺙Ⲧݙⱘ⠽કৃ㛑᳝᠔ϡৠǄ

Remove all tape and lift display

Start Here

If you have problems during setup, see Troubleshooting later in the guide.

a Remove all tape. For best viewing, remove the

protective ﬁ lm from the color graphics display.

b Lift the display.

HP Photosmart 3100 All-in-One series ᅝ㺙᠟ݠ

Important: Do not connect the USB cable until this guide instructs you to or

the software may not install properly.

Locate components

1 Windows CD

2 Macintosh CD

3 User Guide

4 power cord

5 4 x 6 in (10 x 15 cm) photo paper

6 ink cartridges

7 phone cord

8 USB cable

9 control panel faceplate (may be pre-

attached)

The contents of your box may differ.

2 • HP All-in-One

ᅝ㺙᥻ࠊ䴶ᵓ䌈⠛˄བᵰᇮ᳾ᅝ㺙˅

া᳝ᅝ㺙њ᥻ࠊ䴶ᵓ䌈⠛Пৢˈᠡ㛑Փ⫼

HP All-in-Oneʽ

a ᢀ䍋ⲪᄤǄ

b ᇚ᥻ࠊ䴶ᵓ䌈⠛ᬒ೼䆒໛ⱘᣝ䪂ϞǄ

c  ⫼࡯ᣝय़䆹䴶ᵓⲪⱘ৘䖍ˈՓ݊೎ᅮǄ䇋⹂ֱৃ

ҹⳟ㾕᠔᳝ⱘᣝ䪂Ϩᣝ䪂᳾ফ䰏⹡Ǆ

Attach the control panel faceplate (if not attached)

The control panel faceplate must be attached for the

HP All-in-One to work!

a Lift the lid.

b Position the control panel faceplate over the

buttons on the device.

c Press down ﬁ rmly on all edges of the overlay to

secure it. Make sure all buttons are visible and

not blocked.

HP All-in-One • 3

㺙ܹ㒌Ⲧ

೼ᑩ䚼㒌ⲦϞ㺙ܹ᱂䗮ⱑ㒌Ǆ᷵ޚᯊ䳔㽕⫼᱂䗮㒌Ǆ

㺙ܹ4 x 6㣅ᇌ10 x15 cm✻⠛㒌ˈ✻⠛Ⲧⱘܝ⒥䴶৥ϟˈ✻⠛

Ⲧ㕂Ѣߎ㒌ⲦᑩϟǄབᵰ㒌ᓴ㹿ᢝԣˈ䇋⹂ֱᢝ⠛ᳱ৥ᙼǄ

ᦤ⼎˖ܜᢝߎˈ✊ৢ㗏䕀㒌Ⲧᓊ䭓ᵓҹवԣ㒌义Ǆ

abc

ef g

Џ㒌Ⲧ˖

✻⠛㒌Ⲧ˖

Load paper trays

Tip: Pull out, and then ﬂ ip the paper tray extender to catch pages.

Main tray:

Photo paper tray:

Load plain white paper in the bottom paper tray. Plain paper is needed

for alignment.

Load the 4 x 6 in (10 x15 cm) photo paper with the glossy side

down in the photo tray located underneath the output tray. (If paper

is tabbed, make sure the tab is towards you.)

4 • HP All-in-One

䖲᥹⬉⑤㒓

⊼ᛣ˖䰸䴲ᴀᣛफৢ䴶ᣛ⼎ৃҹ䖲᥹USB

⬉㓚ˈ৺߭ϡ㽕Փ⫼䖭㉏⬉㓚Ǆ

ᇚ䱣䰘⬉䆱㒓ⱘϔッ䖲᥹㟇Ꮊջⱘ⬉䆱ッষ (1-LINE) ݙˈᑊᇚ঺ϔ

ッ䖲᥹㟇๭ຕϞⱘᦦᄨݙǄ

㽕䖲᥹⬭㿔ᴎ៪㽕Փ⫼ᙼ㞾Ꮕⱘ⬉䆱㒓ˈ䇋খ䯙ǉՓ⫼᠟ݠǊǄ

䖲᥹䱣䰘ⱘ⬉䆱㒓

Connect the power cord

Important : Do not connect the USB cable

until instructed later in this guide.

Connect the supplied phone cord

Connect one end of the supplied phone cord to the phone port on the

left (1-LINE) and the other to a wall jack.

To connect an answering machine or use your own phone cord, see

the User Guide.

HP All-in-One • 5

ᠧᓔẔׂ䮼

ᣝϟĀᓔ݇ᴎāᣝ䪂ᑊ䖯㸠䜡㕂

a ᣝϟ ᓔ݇ᴎ ᣝ䪂ৢˈ㪱㡆ᣛ⼎♃ᇚӮ䮾⚕ˈ䱣ৢ䕀ܹᘦᅮ⢊ᗕǄ䖭ৃ㛑䳔㽕ϔߚ䩳ⱘᯊ䯈Ǆ

b ㄝᕙߎ⦄䇁㿔ᦤ⼎ˈ✊ৢ㒻㓁᪡԰ǄՓ⫼ㆁ༈䬂䗝ᢽϔ⾡䇁㿔ˈ✊ৢᣝϟ OK ˄⹂ᅮ˅ᑊ䖯㸠⹂䅸Ǆ

Փ⫼ㆁ༈䬂䗝ᢽⳌᑨⱘ೑ᆊഄऎˈ✊ৢᣝϟ OK ˄⹂ᅮ˅ᑊ䖯㸠⹂䅸Ǆ

ᓔ݇ᴎ

Press the On button and configure

Open the access door

a After you press the On button, the blue light ﬂ ashes, and then becomes solid. This may take up to a

minute.

b Wait for the language prompt before continuing. Use the arrow keys to select a language, press OK ,

and then conﬁ rm. Use the arrow keys to select your country/region, press OK , and then conﬁ rm.

6 • HP All-in-One

ᢀ䍋䆒໛ݙ䚼ⱘᦦ䫔

a ᣸य़↣Ͼᦦ䫔ⱘᑩ䚼ˈᇚ݊䞞ᬒˈ✊ৢᢀ䍋ᦦ

䫔Ǆ

b ᢀ䍋ܼ䚼݁Ͼᦦ䫔Ǆ

ᬒܹܼ䚼݁Ͼ๼Ⲧ

a ᇚ咥㡆๼Ⲧ᥼ܹࠄᎺ䖍ⱘ㄀ϔϾᦦῑЁǄ݇䯁ᦦ

䫔Ǆ

b 䞡໡ҹϞ᪡԰ˈᅝ㺙݊ᅗᔽ㡆๼ⲦǄ

c  ⹂ֱ↣Ͼᦦ䫔ᅝ㺙⠶೎Ǆ

ᇚ๼Ⲧⱘ买㡆Ϣ೒Ḝৠᠧॄᬃᶊⱘ买㡆Ϣ೒Ḝऍ䜡Ǆ

Lift latches inside of the device

a Squeeze the bottom of each latch to release it,

and then lift the latch.

b Lift all six latches.

Insert all six ink cartridges

Match the color and pattern of the ink cartridge to the

color and pattern on the print carriage.

a Push the black ink cartridge into the ﬁ rst slot on

the left. Close the latch.

b Repeat with each of the color ink cartridges.

c Make sure each latch is secure.

HP All-in-One • 7

݇䯁Ẕׂ䮼੠ᣝ✻ᦤ⼎᪡԰

a ݇䯁Ẕׂ䮼ৢˈӮߎ⦄㺙ܹ᱂䗮ⱑ㒌ⱘᦤ⼎Ǆ䇋⹂ֱ㒌ᓴ

Ꮖ㺙ܹˈ✊ৢᣝϟ OK ˄⹂ᅮ˅ᓔྟℸ䖛⿟Ǆ

 䆒໛߱ྟ࣪๼Ⲧᑊ᷵ޚᠧॄᴎǄ䖭໻㑺䳔㽕5ߚ䩳Ǆ

b ᔧᠧॄߎ᷵ޚ义ৢˈᠧॄᴎे᷵ޚњǄ䗮䖛ᔽ㡆೒ᔶᰒ⼎

ሣᶹⳟⳌ݇⢊ᗕˈ✊ৢᣝ OK ˄⹂ᅮ˅Ǆ

 ಲᬊ៪϶ᓗ᷵ޚ义Ǆ

 ೼ℸᳳ䯈ˈ䇋࣓ᮁᓔ៪݇䯁

HP All-in-OneǄᙼৃ㛑Ӯ਀㾕䆒໛থߎ

ా䷇Ǆ

ਃࡼ䅵ㅫᴎ

a ਃࡼ䅵ㅫᴎˈḍ᥂䳔㽕䖯㸠ⱏᔩˈ✊ৢㄝᕙḠ䴶ߎ⦄Ǆ

b ݇䯁ӏԩᏆᠧᓔⱘ⿟ᑣǄ

Close the access door and follow the prompts

a After you close the access door, a prompt appears to load

plain white paper. Make sure paper is loaded, and then

press OK to start the process.

The device initializes the ink cartridges and aligns the

printer. This takes approximately 5 minutes.

b After the page prints, the printer is aligned. Check the

color graphics display for the status, and then press OK .

Recycle or discard the alignment page.

Do not disconnect or turn off the

HP All-in-One during this time. You may

hear the device making noises.

Turn on your computer

a Turn on your computer, login if necessary, and then wait for

the desktop to appear.

b Close any open programs.

8 • HP All-in-One

ᬒܹⳌᑨⱘCD

a ᬒܹHP All-in-One Windows CDǄ

b ᣝ✻ሣᐩϞⱘ䇈ᯢᅝ㺙䕃ӊǄ

c ೼䖲᥹㉏ൟሣᐩϞˈ⹂ֱ䗝ЁⳈ᥹ࠄℸ䅵ㅫᴎ䗝

乍Ǆ

a ᡒࠄHP All-in-One Macintosh CDǄ

b 㒻㓁䕀ܹϟϔ义Ǆ

Windows⫼᠋˖ Macintosh⫼᠋˖

⊼˖བᵰ೼ᬒܹCDৢ

≵᳝ߎ⦄ਃࡼሣᐩˈ䇋ձ

⃵ঠߏ Ā៥ⱘ⬉㛥ā ǃ

“CD-ROM” ೒ᷛ੠

“setup.exe” Ǆ

Insert the correct CD

Windows Users:

a Insert the HP All-in-One Windows CD.

b Follow the onscreen instructions to install the

software.

c On the Connection Type screen, make sure to select

directly to this computer .

a Locate the HP All-in-One Macintosh CD.

b Continue to the next page.

Macintosh Users:

Note : If the startup screen

does not appear after you

insert the CD, double-click

My Computer , double-click

the CD-ROM icon, and

then double-click

setup.exe .

HP All-in-One • 9

䖲᥹USB⬉㓚

Windows⫼᠋˖

a ᣝ✻ሣᐩϞⱘ䇈ᯢ䖯㸠᪡԰ˈⳈࠄ㋏㒳ᦤ⼎ᙼ䖲᥹

USB⬉㓚Ǆ˄䖭ৃ㛑䳔㽕޴ߚ䩳ⱘᯊ䯈Ǆ˅

 ߎ⦄Ϟ䗄ᦤ⼎ৢˈ䇋ᇚUSB⬉㓚ⱘϔッ䖲᥹ࠄ

HP All-in-One㚠䴶ⱘッষЁˈ✊ৢᇚ঺ϔッ䖲᥹

ࠄ䅵ㅫᴎϞ ӏᛣⱘ USB ッষ ЁǄ

Macintosh⫼᠋˖

a ᇚUSB⬉㓚Ң䅵ㅫᴎϞ䖲᥹ࠄᴀ䆒໛㚠

䴶ⱘUSBッষЁǄ

Windows Users:

Macintosh Users:

a Follow the onscreen instructions until you see the

prompt to connect the USB cable. (This may take

several minutes.)

Once the prompt appears, connect the USB cable

to the port on the back of the HP All-in-One, and

then to any USB port on your computer.

a Connect the USB cable from your computer

to the USB port on the back of the device.

Connect the USB cable

10 • HP All-in-One

Windows⫼᠋˖

b ᣝ✻ሣᐩϞⱘ䇈ᯢ䖯㸠᪡԰Ǆ೼ ĀӴⳳ䆒㕂৥ᇐā

੠ Āゟे⊼ݠā ሣᐩϞᅠ៤Ⳍᑨⱘ᪡԰Ǆ

b ঠߏ “HP All-in-One Installer” ೒ᷛǄ

c  ⹂ֱᏆᅠ៤᠔᳝ሣᐩϞⱘ᪡԰ˈ݊Ёࣙ

ᣀ“Setup Assistant”˄ᅝ㺙ᐂࡽ˅Ǆ

㒻㓁䖲᥹USB⬉㓚

ᙁ୰ʽ

བᵰᙼ≵᳝ⳟࠄℸሣᐩˈ䇋খ䯙᳔ৢϔ䚼ߚⱘ⭥䲒ᥦ㾷 Ǆ

ᅠ៤䕃ӊᅝ㺙ৢˈᙼेᅠ៤њ᪡԰Ǆ

㽕њ㾷᳝݇བԩ䗮䖛ݙᄬवᠧॄ✻⠛ҹঞ݊ᅗࡳ㛑ⱘֵᙃˈ

䇋খ䯙ǉՓ⫼᠟ݠǊ੠㘨ᴎᐂࡽǄ᳝݇݊ᅗᐂࡽֵᙃˈ䇋খ䯙

www.hp.com/support Ǆ

Macintosh⫼᠋˖

After you complete software installation, you are ﬁ nished.

To learn about printing photos from memory cards and other features,

see the User Guide and online help. For additional help, see

www.hp.com/support .

Connect the USB cable continued

Congratulations!

b Double-click the HP All-in-One Installer

icon.

c Make sure you complete all screens,

including the Setup Assistant.

Windows Users:

b Follow the onscreen instructions. Complete the Fax

Setup Wizard and the Sign up now screens.

If you do not see this screen, see Troubleshooting in the

last section.

Macintosh Users:

䯂乬˖ሣᐩϞϡᰒ⼎䖲᥹USB⬉㓚ⱘᦤ⼎ֵᙃǄ

㾷އᮍ⊩˖পߎᑊ䞡ᮄᬒܹHP All-in-One Windows CDǄ䇋খ䯙ℹ偸14੠15Ǆ

䯂乬˖ ߎ⦄Microsoft ⏏ࡴ⹀ӊ ሣᐩǄ

㾷އࡲ⊩˖ऩߏ Āপ⍜ā ǄᢨᥝUSB⬉㓚ˈ✊ৢᬒܹHP All-in-One Windows CDǄ

䇋খ䯙ℹ偸14੠15Ǆ

䯂乬˖ߎ⦄ Ā䆒໛ᅝ㺙༅䋹ā ሣᐩǄ

㾷އࡲ⊩˖Ẕᶹ᥻ࠊ䴶ᵓ䌈⠛ᰃ৺Ꮖᅝ㺙⠶೎ǄᮁᓔHP All-in-One䖲᥹ˈ✊ৢݡ䞡

ᮄ䖲᥹ǄẔᶹ᠔᳝䖲᥹Ǆ⹂ֱUSB⬉㓚Ꮖᦦܹ䅵ㅫᴎǄϡ㽕ᇚUSB⬉㓚ᦦ೼䬂Ⲭ

៪᮴⑤䲚㒓఼ϞǄ䇋খ䯙ℹ偸14੠15Ǆ

⭥䲒ᥦ㾷

䯂乬˖ߎ⦄व㒌 ⍜ᙃǄ

㾷އࡲ⊩˖পߎẔׂ䮼ˈ✊ৢ䕏䕏ഄᢝߎ᠔᳝㒌ᓴǄ݇䯁䆒໛ˈ✊ৢݡᠧᓔǄݡ⃵㺙

ܹ㒌ᓴǄ

Փ⫼㟇ᇥ50%ᅠܼݡ⫳㑸㓈˄㟇ᇥ݋᳝10%⍜䌍ৢ㒌ᓴ˅ॄࠋǄ

Printed in [].

*Q5831-90175*

Q5831-90175

*Q5831-90175*

Printed on at least 50% total recycled ﬁ ber with at least 10% post-consumer paper.

Problem: You did not see the screen prompting you to connect the USB cable.

Action: Remove, and then re-insert the HP All-in-One Windows CD. Refer to Steps 14

and 15.

Problem: The Microsoft Add Hardware screen appears.

Action: Click Cancel . Unplug the USB cable, and then insert the HP All-in-One

Windows CD. Refer to Steps 14 and 15.

Problem: The Device Setup Has Failed To Complete screen appears.

Action: Verify that the control panel faceplate is ﬁ rmly attached. Unplug the

HP All-in-One and plug it in again. Check all connections. Make sure the USB cable is

plugged into the computer. Do not plug the USB cable into a keyboard or non-powered

hub. Refer to Steps 14 and 15.

Troubleshooting

Problem: A Paper Jam message appears.

Action: Remove the back access door, and then gently pull out any paper. Turn the

device off, and then on. Load the paper again.

Printed in [].

HP (Hewlett-Packard) All in One Printer 2600 User manual

Brand: HP (Hewlett-Packard)

Model: All in One Printer 2600

Type: User manual

This manual is also suitable for

2600
2700

Download PDF

report

HP (Hewlett-Packard) All in One Printer 2600 User manual

This manual is also suitable for

HP (Hewlett-Packard) All in One Printer 2600 User manual

Related papers

Other documents