Milwaukee M18 2605-20 User guide

Brand: Milwaukee

Model: M18 2605-20

Category: Power tools

Type: User guide

This manual is also suitable for

OPERATOR'S MANUAL

MANUEL de L'UTILISATEUR

MANUAL del OPERADOR

TO REDUCE THE RISK OF INJURY, USER MUST READ AND UNDERSTAND OPERATOR'S

MANUAL.

AFIN DE RÉDUIRE LE RISQUE DE BLESSURES, L'UTILISATEUR DOIT LIRE ET BIEN

COMPRENDRE LE MANUEL DE L'UTILISATEUR.

PARA REDUCIR EL RIESGO DE LESIONES, EL USUARIO DEBE LEER Y ENTENDER EL

MANUAL DEL OPERADOR.

Cat. No.

No de cat.

2605-20

M18™ CORDLESS 7/8" SDS PLUS ROTARY HAMMER

MARTEAU ROTATIF M18™ 22

MARTEAU ROTATIF M18™ 22 mm

(7/8")

ROTOMARTILLOS DE M18™ 22

ROTOMARTILLOS DE M18™ 22 mm

(7/8")

SDS

PLUS

PERSONAL SAFETY

GENERAL POWER TOOL SAFETY WARNINGS

WORK AREA SAFETY

ELECTRICAL SAFETY

POWER TOOL USE AND CARE

• Recharge only with the charger speciﬁ ed by

the manufacturer. A charger that is suitable for

one type of battery pack may create a risk of ﬁ re

when used with another battery pack.

BATTERY TOOL USE AND CARE

• Keep work area clean and well lit. Cluttered or

dark areas invite accidents.

• Do not operate power tools in explosive atmos-

pheres, such as in the presence of ﬂ ammable

liquids, gases or dust. Power tools create sparks

which may ignite the dust or fumes.

• Keep children and bystanders away while

operating a power tool. Distractions can cause

you to lose control.

• Power tool plugs must match the outlet. Never

modify the plug in any way. Do not use any

adapter plugs with earthed (grounded) power

tools. Unmodiﬁ ed plugs and matching outlets will

reduce risk of electric shock.

• Avoid body contact with earthed or grounded

surfaces such as pipes, radiators, ranges and

refrigerators. There is an increased risk of electric

shock if your body is earthed or grounded.

• Do not expose power tools to rain or wet condi-

tions. Water entering a power tool will increase

the risk of electric shock.

• Do not abuse the cord. Never use the cord for

carrying, pulling or unplugging the power tool.

Keep cord away from heat, oil, sharp edges

or moving parts. Damaged or entangled cords

increase the risk of electric shock.

• When operating a power tool outdoors, use an

extension cord suitable for outdoor use. Use

of a cord suitable for outdoor use reduces the risk

of electric shock.

• If operating a power tool in a damp location is

unavoidable, use a ground fault circuit inter-

rupter (GFCI) protected supply. Use of an GFCI

reduces the risk of electric shock.

• Stay alert, watch what you are doing and use

common sense when operating a power tool.

Do not use a power tool while you are tired or

under the inﬂ uence of drugs, alcohol or medi-

cation. A moment of inattention while operating

power tools may result in serious personal injury.

• Use personal protective equipment. Always

wear eye protection. Protective equipment such

as dust mask, non-skid safety shoes, hard hat, or

hearing protection used for appropriate conditions

will reduce personal injuries.

• Prevent unintentional starting. Ensure the

switch is in the off-position before connecting

to power source and/or battery pack, picking

up or carrying the tool. Carrying power tools with

your ﬁ nger on the switch or energising power tools

that have the switch on invites accidents.

• Remove any adjusting key or wrench before

turning the power tool on. A wrench or a key left

attached to a rotating part of the power tool may

result in personal injury.

• Do not overreach. Keep proper footing and

balance at all times. This enables better control

of the power tool in unexpected situations.

• Dress properly. Do not wear loose clothing or

jewellery. Keep your hair, clothing and gloves

away from moving parts. Loose clothes, jewel-

lery or long hair can be caught in moving parts.

• If devices are provided for the connection of

dust extraction and collection facilities, ensure

these are connected and properly used. Use of

dust collection can reduce dust-related hazards.

• Do not force the power tool. Use the correct

power tool for your application. The correct

power tool will do the job better and safer at the

rate for which it was designed.

• Do not use the power tool if the switch does not

turn it on and off. Any power tool that cannot be

controlled with the switch is dangerous and must

be repaired.

• Disconnect the plug from the power source

and/or the battery pack from the power tool

before making any adjustments, changing

accessories, or storing power tools. Such pre-

ventive safety measures reduce the risk of starting

the power tool accidentally.

• Store idle power tools out of the reach of chil-

dren and do not allow persons unfamiliar with

the power tool or these instructions to operate

the power tool. Power tools are dangerous in the

hands of untrained users.

• Maintain power tools. Check for misalignment

or binding of moving parts, breakage of parts

and any other condition that may affect the

power tool’s operation. If damaged, have the

power tool repaired before use. Many accidents

are caused by poorly maintained power tools.

• Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges

are less likely to bind and are easier to control.

• Use the power tool, accessories and tool bits

etc. in accordance with these instructions, tak-

ing into account the working conditions and

the work to be performed. Use of the power tool

for operations different from those intended could

result in a hazardous situation.

WARNING READ ALL SAFETY WARNINGS AND ALL INSTRUCTIONS. Failure to

follow the warnings and instructions may result in electric shock, ﬁ re and/or serious injury. Save

all warnings and instructions for future reference. The term “power tool” in the warn-

ings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool.

FUNCTIONAL DESCRIPTION

SPECIFICATIONS

Cat. No. Volts DC

No Load

RPM

No Load

Blows per

Minute

Capacities

Drill Only Rotary Hammer (concrete)

Steel Wood Carbide Tipped Percussion Bit

2605-20 18 0 - 1400 0 - 4800 1/2" 1" 7/8"

SYMBOLOGY

• Wear ear protectors. Exposure to noise can

cause hearing loss.

• Use auxiliary handle(s), if supplied with the

tool. Loss of control can cause personal injury.

• Hold power tool by insulated gripping sur-

faces, when performing an operation where

the cutting tool may contact hidden wiring.

Cutting accessory contacting a “live” wire may

make exposed metal parts of the power tool “live”

and could give the operator an electric shock.

• Maintain labels and nameplates. These carry im-

portant information. If unreadable or missing, contact

a MILWAUKEE service facility for a free replacement.

• WARNING Some dust created by power sanding,

sawing, grinding, drilling, and other construction

activities contains chemicals known to cause

cancer, birth defects or other reproductive harm.

Some examples of these chemicals are:

• lead from lead-based paint

• crystalline silica from bricks and cement and

other masonry products, and

• arsenic and chromium from chemically-treated

lumber.

Your risk from these exposures varies, depending

on how often you do this type of work. To reduce

your exposure to these chemicals: work in a well

ventilated area, and work with approved safety

equipment, such as those dust masks that are spe-

cially designed to ﬁ lter out microscopic particles.

1. Side handle

2. Clamp

3. Depth gauge rod

4. SDS Plus bit holder

5. Release collar

6. Mode selector

7. Selector release button

8. Trigger

9. Control switch

SPECIFIC SAFETY RULES

• Have your power tool serviced by a qualiﬁ ed

repair person using only identical replacement

parts. This will ensure that the safety of the power

tool is maintained.

SERVICE

Volts

Direct Current

BPM

Blows per Minute (BPM)

No Load Revolutions per

Minute (RPM)

Underwriters Laboratories, Inc.

United States and Canada

• Use power tools only with speciﬁ cally desig-

nated battery packs. Use of any other battery

packs may create a risk of injury and ﬁ re.

• When battery pack is not in use, keep it away

from other metal objects like paper clips,

coins, keys, nails, screws, or other small metal

objects that can make a connection from one

terminal to another. Shorting the battery terminals

together may cause burns or a ﬁ re.

• Under abusive conditions, liquid may be eject-

ed from the battery; avoid contact. If contact

accidentally occurs, ﬂ ush with water. If liquid

contacts eyes, additionally seek medical help.

Liquid ejected from the battery may cause irritation

or burns.

OPERATION

WARNING To reduce the risk of injury,

keep hands away from the bit and all moving

parts. Always wear safety goggles or glasses

with side shields.

Fig. 1

Drilling

Depth

Installing Drill Bits and Chisels

NOTE: Only use accessories with SDS or SDS

Plus shanks.

Be sure that the shank of the bit is clean. Dirt par-

ticles may cause the bit to line up improperly. Do not

use bits larger than the maximum recommended

capacity of the drill because gear damage or mo-

tor overloading may result. For best performance,

be sure that the bit is properly sharpened and the

shank is lightly greased before use.

1. Insert the bit or chisel into the nose of the tool.

2. Rotate bit slowly until it aligns with the locking

mechanism.

3. Push bit into tool until it locks.

4. Check that the bit is locked properly; it should

be possible to pull the bit back and forth slightly

(about 1/4").

5. To remove bits and chisels, pull bit holder release

collar toward the rear of tool and remove bit.

NOTE: Use caution when handling hot bits and

chisels.

Selecting Action

MILWAUKEE Rotary Hammers have three settings:

rotation only, rotary hammer, and hammer only.

Always allow the motor to come to a complete

stop before changing the mode selection to avoid

damage to the tool.

1. For rotation only, press in

the selector release button

and turn the selector lever

so the arrow on the lever

points to the twist drill

symbol.

2. For rotary hammering, press

in the selector release button and turn the selec-

tor lever so the arrow points to the hammer and

twist drill symbol.

3. For hammering only, press in the selector release

button and turn the selector lever so the arrow

points to the hammer symbol.

4. To freely rotate the bit to the desired angle for

hammering only, press in the selector release

button and turn the selector lever to the

symbol. Then, follow step 3.

NOTE: To engage the hammering mechanism,

maintain pressure on the bit. When pressure on the

bit is released, the hammering action will stop.

Using the Control Switch

The control switch may be set to three positions:

forward, reverse and lock. Always allow the motor

to come to a complete stop before using the control

switch to avoid damage to the tool.

For forward (clockwise) rotation, push in the control

switch from the right side of the tool. Check the

direction of rotation before use.

For reverse (counterclockwise) rotation, push in the

control switch from the left side of the tool. Check

direction of rotation before use.

To lock the trigger, push the control switch to the

center position. The trigger will not work while the

control switch is in the center locked position. Always

lock the trigger or remove the battery pack before

performing maintenance, changing accessories,

storing the tool and any time the tool is not in use.

WARNING Always remove battery

pack before changing or removing acces-

sories. Only use accessories specifically

recommended for this tool. Others may be

hazardous.

ASSEMBLY

WARNING Recharge only with the

charger specified for the battery. For spe-

ciﬁ c charging instructions, read the operator’s

manual supplied with your charger and battery.

Removing Battery Pack from Tool

Push in the release buttons and pull the battery

pack away from the tool.

Inserting Battery Pack into Tool

To insert the battery pack onto the tool, slide the

pack onto the body of the tool. Make sure it latches

securely into place.

Adjusting the Side Handle Position

1. Loosen the side handle by unscrewing the side

handle grip until the side handle rotates freely.

2. Rotate the side handle to the desired position.

3. Tighten the side handle grip securely.

Setting the Depth Gauge

1. Press in the clamping lever.

2. Slide the depth gauge rod backward or forward

until it is set for the desired depth.

NOTE: The drilling depth is the distance between

the tip of the bit and the tip of the depth gauge rod.

3. Release the clamping lever.

WARNING Always remove battery

pack before changing or removing acces-

sories. Only use accessories specifically

recommended for this tool. Others may be

hazardous.

WARNING To reduce the risk of injury,

always use a side handle when using this tool.

Always brace or hold securely.

APPLICATIONS

Selecting Bits

When selecting a bit, use the right type for your job.

For best performance, always use sharp bits.

Drilling

1. Before drilling, be sure the workpiece is clamped

securely. Use backing material to prevent dam-

age to the workpiece during breakthrough.

2. When starting a hole, place the drill bit on the

work surface and apply ﬁ rm pressure. Begin

drilling at a slow speed, gradually increasing the

speed as you drill.

3. Always apply pressure in line with the bit. Use

enough pressure to keep the drill biting, but do

not push hard enough to stall the motor.

4. Reduce pressure and ease the bit through the

last part of the hole. While the tool is still running,

pull the bit out of the hole to prevent jamming.

Drilling in Wood, Composition Materials and

Plastic

(Use chuck adapter kit Cat. No. 48-66-1370)

When drilling in wood, composition materials and

plastic, start the drill slowly, gradually increasing

speed as you drill. When drilling into wood, use

wood augers or twist drill bits. Always use sharp

bits. When using twist drill bits, pull the bit out of the

hole frequently to clear chips from the bit ﬂ utes. To

reduce the chance of splintering, back work with a

piece of scrap wood. Select low speeds for plastics

with a low melting point.

Starting, Stopping and Controlling Speed

1. To start the tool, grasp the handle ﬁ rmly and pull

the trigger.

2. To vary the speed, increase or decrease the

pressure on the trigger. The further the trigger

is pulled, the greater the speed.

3. To stop the tool, release the trigger. Make sure

the tool comes to a complete stop before laying

the tool down.

Operating

Position the tool, grasp the handles ﬁ rmly and pull

the trigger. Always hold the tool securely using both

handles to maintain control. This tool has been

designed to achieve top performance with only

moderate pressure. Let the tool do the work.

If the speed begins to drop off when drilling large

or deep holes, pull the bit partially out of the hole

while the tool is running to help clear dust. Do not

use water to settle the dust since it will clog the bit

ﬂ utes and tend to make the bit bind in the hole. If

the bit should bind, a built-in, non-adjustable slip

clutch prevents the bit from turning. If this occurs,

stop the tool, free the bit and begin again.

ACCESSORIES

For a complete listing of accessories refer to your

MILWAUKEE Electric Tool catalog or go online

to www.milwaukeetool.com. To obtain a catalog,

contact your local distributor or service center.

WARNING Always remove battery pack

before changing or removing accessories.

Only use accessories speciﬁ cally recommend-

ed for this tool. Others may be hazardous.

Maintaining Tool

Keep your tool, battery pack and charger in good

repair by adopting a regular maintenance program.

After six months to one year, depending on use,

return the tool, battery pack and charger to A

MILWAUKEE service facility for:

• Lubrication

• Mechanical inspection and cleaning (gears, spin-

dles, bearings, housing, etc.)

• Electrical inspection (battery pack, charger,

motor)

• Testing to assure proper mechanical and electrical

operation

If the tool does not start or operate at full power

with a fully charged battery pack, clean the contacts

on the battery pack. If the tool still does not work

properly, return the tool, charger and battery pack,

to a MILWAUKEE service facility for repairs.

MAINTENANCE

Cleaning

Clean dust and debris from charger and tool vents.

Keep tool handles clean, dry and free of oil or

grease. Use only mild soap and a damp cloth to

clean the tool, battery pack and charger since certain

cleaning agents and solvents are harmful to plastics

and other insulated parts. Some of these include

gasoline, turpentine, lacquer thinner, paint thinner,

chlorinated cleaning solvents, ammonia and house-

hold detergents containing ammonia. Never use

ﬂ ammable or combustible solvents around tools.

Repairs

For repairs, return the tool, battery pack and

charger to the nearest service center.

WARNING To reduce the risk of per-

sonal injury and damage, never immerse your

tool, battery pack or charger in liquid or allow

a liquid to ﬂ ow inside them.

WARNING To reduce the risk of injury,

always unplug the charger and remove the

battery pack from the charger or tool before

performing any maintenance. Never disas-

semble the tool, battery pack or charger.

Contact a MILWAUKEE service facility for

ALL repairs.

LIMITED WARRANTY - USA AND CANADA

LIMITED WARRANTY - MEXICO, CENTRAL AMERICA AND CARIBBEAN

Every MILWAUKEE power tool (including cordless product – tool, battery pack(s) - see separate & distinct

CORDLESS BATTERY PACK LIMITED WARRANTY statements & battery charger and Work Lights*) is war-

ranted to the original purchaser only to be free from defects in material and workmanship. Subject to certain

exceptions, MILWAUKEE will repair or replace any part on an electric power tool which, after examination, is

determined by MILWAUKEE to be defective in material or workmanship for a period of ﬁ ve (5) years* after the

date of purchase unless otherwise noted. Return of the power tool to a MILWAUKEE factory Service Center

location or MILWAUKEE Authorized Service Station, freight prepaid and insured, is required. A copy of the

proof of purchase should be included with the return product. This warranty does not apply to damage that

MILWAUKEE determines to be from repairs made or attempted by anyone other than MILWAUKEE authorized

personnel, misuse, alterations, abuse, normal wear and tear, lack of maintenance, or accidents.

*The warranty period for, Job Site Radios, M12™ Power Port, M18™ Power Source, and Trade Titan™ Indus-

trial Work Carts is one (1) year from the date of purchase. The warranty period for a LED Work Light and LED

Upgrade Bulb is a limited LIFETIME warranty to the original purchaser only, if during normal use the LED bulb

fails the Work Light or Upgrade Bulb will be replaced free of charge.

*This warranty does not cover Air Nailers & Stapler, Airless Paint Sprayer, Cordless Battery Packs, Gasoline

Driven Portable Power Generators, Hand Tools, Hoist – Electric, Lever & Hand Chain, M12™ Heated Jackets,

Reconditioned product and Test & Measurement products. There are separate and distinct warranties avail-

able for these products.

Warranty Registration is not necessary to obtain the applicable warranty on a MILWAUKEE power tool product.

The manufacturing date of the product will be used to determine the warranty period if no proof of purchase is

provided at the time warranty service is requested.

ACCEPTANCE OF THE EXCLUSIVE REPAIR AND REPLACEMENT REMEDIES DESCRIBED HEREIN IS A

CONDITION OF THE CONTRACT FOR THE PURCHASE OF EVERY MILWAUKEE PRODUCT. IF YOU DO NOT

AGREE TO THIS CONDITION, YOU SHOULD NOT PURCHASE THE PRODUCT. IN NO EVENT SHALL MIL-

WAUKEE BE LIABLE FOR ANY INCIDENTAL, SPECIAL, CONSEQUENTIAL OR PUNITIVE DAMAGES, OR FOR

ANY COSTS, ATTORNEY FEES, EXPENSES, LOSSES OR DELAYS ALLEGED TO BE AS A CONSEQUENCE

OF ANY DAMAGE TO, FAILURE OF, OR DEFECT IN ANY PRODUCT INCLUDING, BUT NOT LIMITED TO, ANY

CLAIMS FOR LOSS OF PROFITS. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF IN-

CIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY

TO YOU. THIS WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER EXPRESS WARRANTIES, WRITTEN

OR ORAL. TO THE EXTENT PERMITTED BY LAW, MILWAUKEE DISCLAIMS ANY IMPLIED WARRANTIES,

INCLUDING WITHOUT LIMITATION ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A

PARTICULAR USE OR PURPOSE; TO THE EXTENT SUCH DISCLAIMER IS NOT PERMITTED BY LAW, SUCH

IMPLIED WARRANTIES ARE LIMITED TO THE DURATION OF THE APPLICABLE EXPRESS WARRANTY AS

DESCRIBED ABOVE. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY

LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU, THIS WARRANTY GIVES YOU SPECIFIC

LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE.

This warranty applies to product sold in the U.S.A. and Canada only.

Please consult the ‘Service Center Search’ in the Parts & Service section of MILWAUKEE’s website www.mil-

waukeetool.com or call 1.800.SAWDUST (1.800.729.3878) to locate your nearest service facility for warranty

and non-warranty service on a Milwaukee electric power tool.

Model:

Date of Purchase:

Distributor or Store Stamp:

TECHTRONIC INDUSTRIES' warranty is for 5 year since the original purchase date.

This warranty card covers any defect in material and workmanship on this Power Tool.

To make this warranty valid, present this warranty card, sealed/stamped by the distributor or store where you pur-

chased the product, to the Authorized Service Center (ASC). Or, if this card has not been sealed/stamped, present the

original proof of purchase to the ASC.

Call toll-free 1 800 832 1949 to ﬁ nd the nearest ASC, for service, parts, accessories or components.

Procedure to make this warranty valid

Take the product to the ASC, along with the warranty card sealed/stamped by the distributor or store where you pur-

chased the product, and there any faulty piece or component will be replaced without cost for you. We will cover all

freight costs relative with this warranty process.

Exceptions

This warranty is not valid in the following situations:

a) When the product is used in a different manners from the end-user guide or instruction manual.

b) When the conditions of use are not normal.

c) When the product was modiﬁ ed or repaired by people not authorized by TECHTRONIC INDUSTRIES.

Note: If cord set is damaged, it should be replaced by an Authorized Service Center to avoid electric risks.

SERVICE AND ATTENTION CENTER

Av Presidente Mazarik 29 Piso 7, 11570 Chapultepec Morales

Miguel Hidalgo, Distrito Federal, Mexico

Ph. 52 55 4160-3547

IMPORTED AND COMMERCIALIZED BY:

TECHTRONIC INDUSTRIES MEXICO, .S.A. DE C.V.

Av Presidente Mazarik 29 Piso 7, 11570 Chapultepec Morales

Miguel Hidalgo, Distrito Federal, Mexico

Page is loading ...

MILWAUKEE ELECTRIC TOOL CORPORATION

13135 West Lisbon Road • Brookﬁ eld, Wisconsin, U.S.A. 53005

58-14-2607d3 10/13 Printed in China

960931620-03( )

UNITED STATES

MILWAUKEE Service

CANADA - Service MILWAUKEE

MILWAUKEE prides itself in producing a premium

quality product that is NOTHING BUT HEAVY DUTY

Your satisfaction with our products is very impor-

tant to us! If you encounter any problems with the

operation of this tool, or you would like to locate the

factory Service/Sales Support Branch or authorized

service station nearest you, please call...

Additionally, we have a nationwide network of

authorized Distributors ready to assist you with

your tool and accessory needs. Check your “Yellow

Pages” phone directory under “Tools-Electric” for

the names & addresses of those nearest you or see

the 'Where To Buy' section of our website.

1-800-SAWDUST

(1.800.729.3878)

Monday-Friday

7:00 AM - 6:30 PM

Central Time

or visit our website at

www.milwaukeetool.com

For service information, use the 'Service Center

Search' icon found in the 'Parts & Service' section.

Contact our Corporate After Sales Service

Technical Support about ...

• Technical Questions

• Service/Repair Questions

• Warranty

call: 1-800-SAWDUST

fax: 1.800.638.9582

email: [email protected]

www.milwaukeetool.com and...

• receive important notiﬁ cations regarding

your purchase

• ensure that your tool is protected under the

warranty

• become a HEAVY DUTY club member

MILWAUKEE prides itself in producing a premium

quality product that is N

OTHING BUT HEAVY DUTY

Your satisfaction with our products is very important

to us!

If you encounter any problems with the operation

of this tool, or you would like to locate the factory

Service/Sales Support Branch or authorized

service station nearest you, please call...

1.800.268.4015

Monday – Friday 7:00 – 4:30 CST

fax: 866.285.9049

Milwaukee Electric Tool (Canada) Ltd

140 Fernstaff Court, Unit 4 18129 111 Avenue NW

Vaughan, ON L4K 3L8 Edmonton, AB T5S 2P2

Additionally, we have a nationwide network of

authorized Distributors ready to assist you with your

tool and accessory needs. Call 1.800.268.4015

to ﬁ nd the names and addresses of the closest

retailers or consult “Where to buy” on our Web site

www.milwaukeetool.com

MILWAUKEE est ﬁ er de proposer un produit de

première qualité NOTHING BUT HEAVY DUTY

. Votre

satisfaction est ce qui compte le plus!

En cas de problèmes d’utilisation de l’outil ou pour

localiser le centre de service/ventes ou le centre

d’entretien le plus proche, appelez le...

1.800.268.4015

Lundi – Vendredi 7:00 – 4:30 CST

fax: 866.285.9049

Milwaukee Electric Tool (Canada) Ltd

140 Fernstaff Court, Unit 4 18129 111 Avenue NW

Vaughan, ON L4K 3L8 Edmonton, AB T5S 2P2

Notre réseau national de distributeurs agréés se

tient à votre disposition pour fournir l’aide technique,

l’outillage et les accessoires nécessaires.

Composez le 1.800.268.4015 pour obtenir les

noms et adresses des revendeurs les plus proches

ou bien consultez la section «Où acheter» sur notre

site web à l’adresse www.milwaukeetool.com

CENTRO DE ATENCION A CLIENTES

Av. Presidente Masarik 29 Piso 7

CP. 11570. Col. Chapultepec Morales

Del. Miguel Hidalgo, Distrito Federal, México

01-800-8321949

Lunes a Viernes (9am a 6pm)

O contáctanos en www.milwaukeetool.com.mx

Para información de Centros de Servicio busca

el icono “Servicio al cliente”- “Contáctanos”

Contacta nuestro servicio técnico para….

• Preguntas Técnicas

• Asesoría, servicio y reparación

• Garantía

Adicionalmente, tenemos una red nacional de

distribuidores autorizados listos para ayudarle

con su herramienta y sus accesorios. Por favor,

llame al 01 800 8321949 para obtener los nombres

y direcciones de los más cercanos a usted, o

consulte la sección "Dónde Comprar" en nuestro

sitio web www.milwaukeetool.com.mx

MEXICO - Soporte de Servicio MILWAUKEE

Milwaukee M18 2605-20 User guide

Brand: Milwaukee

Model: M18 2605-20

Category: Power tools

Type: User guide

This manual is also suitable for

Download PDF

report

in other languages

français: Milwaukee M18 2605-20 Mode d'emploi
español: Milwaukee M18 2605-20 Guía del usuario

Milwaukee M18 2605-20 User guide

This manual is also suitable for

Milwaukee M18 2605-20 User guide

in other languages

Related papers

Other documents