Desa (V)CD36RP User manual

Save this manual for future reference.

For more information, visit www.desatech.com

WARNING: If the information in this manual is not fol-





         





— WHAT TO DO IF YOU SMELL GAS

 

• Do not touch any electrical switch; do not use any



 



 



 -



DIRECT-VENT FIREPLACE

OWNER’S OPERATION AND INSTALLATION MANUAL

NATURAL GAS MODELS

(V)CD36RN, (V)CD36RNE

PROPANE/LP GAS MODELS

(V)CD36RP, (V)CD36RPE

NATURAL GAS MODELS

(V)CD36TN, (V)CD36TNE,

PROPANE/LP GAS MODELS

(V)CD36TP, (V)CD36TPE

www.desatech.com

116035-01E2

    -

-



      -





-





-













TABLE OF CONTENTS

Safety Information ............................................... 3

Product Identication ........................................... 4

Local Codes......................................................... 5

Product Features ................................................. 5

Pre-Installation Preparation ................................. 5

Location of Termination Cap ................................ 9

Venting Installation Instructions ......................... 10

Fireplace Installation.......................................... 21

Operating Fireplace ........................................... 31

Inspecting Burners............................................. 36

Cleaning and Maintenance ................................ 37

Troubleshooting ................................................. 38

Replacement Parts ............................................ 44

Service Hints ..................................................... 44

Technical Service............................................... 44

Specications .................................................... 44

Accessories ....................................................... 45

Illustrated Parts Breakdown and Parts List........ 46

Warranty Information ...........................Back Cover

www.desatech.com

116035-01E 3

    



    

-







-







   











WARNING: Do not allow fans







    









    







-



-

   

adults away from hot surface to









SAFETY INFORMATION

-









   







     

    

   

   







This replace must be installed by a qualied (cer-

tied or licensed) service person. It has a sealed

gas combustion chamber that uses a coaxial pipe

(pipe within a pipe and having the same center)

venting system. It brings in fresh air for combus-

tion through the outer pipe and combustion gases

are exhausted through the inner pipe. If the glass

door assembly and venting pipe are not properly

seated, connected and sealed, carbon monoxide

leakage (spillage) can occur.

   Early signs of

carbon monoxide poisoning resemble the u, with

headaches, dizziness or nausea. If you have these

signs, the replace may not be working properly.

Get fresh air at once! Have replace serviced.

Some people are more affected by carbon monoxide

than others. These include pregnant women, people

with heart or lung disease or anemia, those under the

inuence of alcohol and those at high altitudes.

    Propane/LP and

natural gas are odorless. An odor-making agent is

added to the gas. The odor helps you detect a gas

leak. However, the odor added to the gas can fade.

Gas may be present even though no odor exists.

Make certain you read and understand all warnings.

Keep this manual for reference. It is your guide to

safe and proper operation of this replace.

www.desatech.com

116035-01E4

   -

dren when they are in the room



    

   

   



    



1. For propane/LP replace, do not place pro-

pane/LP supply tank(s) inside any structure.

Locate propane/LP supply tank(s) outdoors.

To prevent performance problems, do not

use propane/LP fuel tank of less than 100 lbs.

capacity.

2. If you smell gas

• shut off gas supply

• do not try to light any appliance

• do not touch any electrical switch; do not use

any phone in your building

• immediately call your gas supplier from a

neighbor’s phone. Follow the gas supplier's

instructions

• if you cannot reach you gas supplier, call the

re department.

3. Never install the replace

• in a recreational vehicle

• in windy or drafty areas where curtains or

other combustible (ammable) objects can

make contact with the replace front

• in high trafc areas

4. Turn replace off and let cool before servicing,

installing or repairing. Only a qualied service

person should install, service or repair this

replace. Have replace inspected annually

by a qualied service person.

5. You must keep control compartments, burn-

ers and circulating air passages clean. More

frequent cleaning may be needed due to ex-

cessive lint and dust from carpeting, bedding

material, etc. Turn off the gas valve and pilot

light before cleaning replace.

6. Have venting system inspected annually by a

qualied service person. If needed, have vent-

ing system cleaned or repaired. See Cleaning

and Maintenance, page 37.

SAFETY INFORMATION

Continued

7. Do not use any solid fuels (wood, coal, paper,

cardboard, etc.) in this replace. Use only the

gas type indicated on replace nameplate.

8. This appliance, when installed, must be elec-

trically grounded in accordance with local

codes or, in the absence of local codes, with

the National Electrical Code, ANSI/NFPA

70 or the Canadian Electrical Code, CSA

C22.1.

9. Do not use replace if any part has been ex-

posed to or under water. Immediately call a

qualied service person to arrange for replace-

ment of the unit.

10. Do not operate replace if any log is broken.

11. Do not operate fireplace with glass door

removed, cracked or broken.

12. Provide adequate clearances around air

openings.

PRODUCT

IDENTIFICATION

Figure 1 - Top and Rear Direct-Vent

Fireplaces

Rear Vent

Flue Collar

Nailing

Flange

Top Vent

Flue Collar

Door

Latch

Log

Set

Ember

Tray

Junction

Box

Lower

Louver

Panel

Control Valve

Variable Input

Adjustment

Piezo Ignitor

with Optional

Remote

and Blower

Control Mount

Upper

Louver

Panel

Glass

Door

Assembly

www.desatech.com

116035-01E 5

LOCAL CODES

Install and use replace with care. Follow all local

codes. In the absence to local codes, use the cur-

rent National Fuel Gas Code ANSI Z223.1/NFPA

54* (USA) or the current CSA-B149.1 Installation

Code (Canada).

*Available from:

American National Standards Institute, Inc.

1430 Broadway

New York, NY 10018

National Fire Protection Association, Inc.

Batterymarch Park

Quincy, MA 02269

PRODUCT FEATURES

These are a few facts that can help you understand

and enjoy your direct-vent replace:

• The CD36R dedicated rear vent is best suited

for ush or corner installations when vented

horizontally through an exterior wall.

• The CD36T dedicated top vent is suited for

any application where height is necessary to

terminate the venting system either through

the roof (vertical) or to gain sufcient height

and offset to vent to an outside/exterior wall

(horizontal).

• The vent pipe installation is very important to

allow for proper operation. You must select

the appropriate unit for your application and

follow the venting instructions to plan your

installation.

• This replace may be installed in any room of

your house provided all local codes and these

installation instructions are followed.

• Models (V)CD36R/T are equipped with a mil-

livolt gas control system that does not require

electricity to operate. A piezo ignitor is provided to

light the pilot without using matches or lighters.

• Models (V)CD36RE/TE are equipped with an

electronic ignition system that requires 120VAC

to operate. An electrode ignitor automati-

cally lights the pilot ame when the replace

is turned on.

• All models can accept an optional circulating

air blower when 120 VAC connection is sup-

plied. If you plan to install an optional blower,

do not forget to wire the replace outlet when

framing.

• Each time you turn on your replace, you may

notice some amount of condensation on the in-

side of the replace glass. This is normal and will

disappear after 10-20 minutes of operation.

Figure 2 - Common Fireplace Locations

Flush with

a wall

Through exterior wall

enclosed in a chase

Corner

installation

• Your direct-vent gas replace system (replace

and venting) is a balanced and sealed gas oper-

ating unit. It is highly efcient because it uses

outside air for combustion while independently

heating the indoor air.

PRE-INSTALLATION

PREPARATION



REqUIREMENTS

Determine the safest and most efcient location

for your DESA direct-vent replace. Make sure

that rafters and wall studs are not in the way of the

venting system. Choose a location where the heat

output is not affected by drafts, air conditioning

ducts, windows or doors. Figure 2 shows some

common locations. Be aware of all restrictions and

precautions before deciding the exact location for

your replace and termination cap.

When deciding the location of your replace,

follow these rules:

• Do not connect this replace venting to a chim-

ney ue serving a separate solid-fuel burning

replace or appliance.

• Due to high temperatures, do not locate this

replace in high trafc areas, windy or drafty

areas or near furniture or draperies.

• Proper clearances must be maintained.

• If your replace is to be installed directly on

carpeting, vinyl tile or any combustible material

other than wood, it must be installed on a metal

or wood panel extending the full width and depth

of the replace. See Figure 3, page 6.

•

Your replace is designed to be used in zero clear-

ance installations. Wall or framing material can be

placed directly against any exterior surface on the

back, sides or top of your replace, except where

standoff spacers are integrally attached. If standoff

spacers are attached to your replace, these spac-

ers can be placed directly against wall or framing

material. See framing details on page 7.

www.desatech.com

116035-01E6

• If you plan on installing a television or enter-

tainment center recessed above your replace, it

is recommended that you maintain a minimum

18" above top of louver opening.

• When locating termination cap, it is important

to observe the minimum clearances shown in

Figure 7, page 8.

• If recessing into a wall, you can avoid extra

framing by positioning your replace against

an already existing framing member.

• Do not recess termination cap into a wall or

siding.

• You may paint the termination cap with 450ºF

(232ºC) heat-resistant paint to coordinate with

the exterior nish.

• There must not be any obstruction such as

bushes, garden sheds, fences, decks or util-

ity buildings within 24" from the front of the

termination cap.

• Do not locate termination cap where excessive

snow or ice build up may occur. Be sure to

clear vent termination area after snow falls to

prevent accidental blockage of venting system.

When using snow blowers, do not direct snow

towards vent termination area.

PRE-INSTALLATION

PREPARATION

Continued



The (V)CD36R/T direct vent gas replace heater

is packaged with:

- one box containing a 4-log set located on the

burner in the rebox.

- one bag containing the owner’s manual with

installation instructions, operator’s guide, and

warranty information.

- one bag of glowing ember material.

- one bag of vermiculite hearth treatments.

Remove the shrink-wrap securing the 2 carton

trays to the unit. Lift the top carton tray off and

remove the four corner posts. Discard the bottom

tray once the unit is moved into position.

Note: On rear vent models you must remove the

berboard collar protector located on the rear

collar before installing the replace and venting

system. See Figure 4.

Figure 4 - Removing Collar Protector

(Rear Vent Fireplace)

Fireboard

Collar

Protector

Figure 3 - Fireplace Bottom Dimensions

15"

(381 mm)

36"

(914 mm)

25"

(635 mm)



Minimum clearances to combustibles for the re-

place are as follows:

*Back and sides 0"/mm

Perpendicular walls 12" (305 mm)

Floor 0"/mm

Ceiling to louver opening 40" (1016 mm)

Front 36" (914 mm)

Top of Standoffs 0"/mm

Vent Surfaces 1" (26 mm) (See venting

instructions for specic

vent clearances.)

Mantel Clearances (See Mantel Clearances

for specics on mantel

clearances.)

Combustible material with a maximum thick-

ness of 5/8" may be ush with the top front of

replace.

    -















    

-







www.desatech.com

116035-01E 7

Figure 5 - Framing Clearances for

Installation Against an Exterior Wall

36"

(914 mm)

(921 mm)

Figure 6 - Framing Clearances for Corner

Installation

PRE-INSTALLATION

PREPARATION

Continued

FRAMING AND FINISHING

Figure 5 shows typical framing of this replace.

Figure 6 shows framing for corner installation. All

minimum clearances must be met.

For overall unit dimensions, framing allowances

and vent collar locations, see Unit Dimensions,

Figure 9, page 8.

For available accessories for this replace, see

Accessories on page 45. If you are using a separate

combustible mantel piece, refer to Figure 7 and

Figure 8, page 8 for proper height and clearances.

You can install noncombustible mantels at any

height above the replace.

Note: Noncombustible mantels may discolor!

(375 mm)

24" Vertical

Double Stud

Ref. Mantel Depth Ref.

Mantel from

Top of Louver

Opening

1 16" (406 mm) A 14" (356 mm)

2 14" (356 mm) A 12" (305 mm)

3 12" (305 mm) B 10" (254 mm)

4 10" (254 mm) C 8" (203 mm)

5 8" (203 mm) D 6" (152 mm)

6 4" (101 mm) F 4" (101 mm)

7 2" (51 mm) G 2" (51 mm)

Figure 7 - Clearances for Combustible

Mantels



Figure 7 shows projected mantel depths at various

heights above the top of the louver opening. Figure

8, page 8, shows the minimum allowable distances

from various mantel components in relation to the

both sides of the replace opening.

   

  -





   



    



used and the face are sealed with



(375 mm)

FOR 1" OF CLEARANCE

AT THE SIDES AND BACK

OF THE FIREPLACE

IS ALSO PERMITTED AT

HOWEVER, 0" CLEARANCE

ALL SIDES WHEN FRAMED

THESE DIMENSIONS ALLOW

21" (533 mm)

TO CENTER OF

TOP VENT

(375 mm)

TO NAILING

FLANGES

(1441 mm)

(311 mm)

OPENING

(727 mm)

" ( 168 mm)

TO CENTER

OF REAR VENT

" (63 mm)

MIN. 1" (26 mm)

www.desatech.com

116035-01E8

PRE-INSTALLATION PREPARATION

Continued

Figure 9 - Rear/Top Common Dimensions

Figure 8 - Side Clearances for Combustible Materials

" (194 mm)

TO CENTER OF

8" TOP VENT

(375 mm)

TO NAILING

FLANGES

5/8"

(16 mm)

36"

(914 mm)

FACE DIM.

(921 mm)

FACE DIM.

(390 mm)

(908 mm)

2 "

(51 mm)

25" (635 mm)

TO CENTER OF

8" REAR VENT

37" (940 mm)

TO NAILING

FLANGE

" (114 mm)

ELECTRICAL

INLET

8" (203 mm)

GAS SUPPLY

INLET

(934 mm)

(921 mm)

TO NAILING

FLANGE

(51 mm)

38"

(965 mm)

(102 mm)

NAILING

FLANGE

WALL SWITCH

WIREWAY

WALL SWITCH

WIREWAY

(63

mm)

33°

SAFE

ZONE

(38 mm)

(95 mm)

(152 mm)

(140 mm)

12"

(305 mm)

Perpendicular

Side Wall

Combustible

Material May

Be Used

Outer Surround

To Fireplace

Opening

www.desatech.com

116035-01E 9

Fixed

Closed

Openable

Fixed

Closed

Openable

TERMINATION CAP

AIR SUPPLY INLET

GAS METER RESTRICTED AREA

(TERMINATION PROHIBITED)

A = clearance above grade, veranda, porch, deck, or balcony

[*12 inches (30.5mc) minimum]

B = clearance to window or door that may be opened

[12 inches (30.5cm) minimum]

C = clearance to permanently closed window [minimum 12 inches

(30.5cm) recommended to prevent condensation on window]

D = vertical clearance to ventilated soffit located above the terminal

within a horizontal distance of 24 inches (61cm) from the

center-line of the terminal [18 inches (45.7cm) minimum]

E = clearance to unventilated soffit [12 inches (30.5cm) minimum]

F = clearance to outside corner (see below)

G = clearance to inside corner (see below)

H = *not to be installed above a meter/regulator assembly within

36 inches (91.4cm) horizontally from the center-line of the regulator

I = clearance to service regulator vent outlet [*72 inches (182.9cm)

minimum]

J = clearance to non-mechanical air supply inlet to building or the

combustion air inlet to any other fireplace [*12 inches (30.5cm)

minimum]

K = clearance to a mechanical air supply inlet [*72 inches (182.9cm)

minimum]

L = † clearance above paved side-walk or a paved driveway located on

public property [*84 inches (213.3cm) minimum]

M = clearance under veranda, porch, deck [*12 inches (30.5cm) minimum ‡]

N = clearance above a roof shall extend a minimum of 24 inches (61cm)

above the highest point when it passes through the roof surface and

any other obstruction within a horizontal distance of 18 inches (45.7cm)

† vent shall not terminate directly above a side-walk or paved driveway which is located between two

single family dwellings and serves both dwellings*

‡ only permitted if veranda, porch, deck or balconey is fully open on a minimum of 2 sides beneath the floor*

* as specified in CAN/CSA B149 (.1 or .2) Installation Codes (1991) for Canada and U.S.A.

Note: Local codes or regulations may require different clearances

A = 6" (15.2cm)

Inside Corner

B = 6" (15.2cm)

C = Maximum depth of 48" (121.9cm) for

recessed location

D = Minimum width for back wall of

recessed location -

Combustible - 38" (965mm)

Noncombustible - 24" (61cm)

E = Clearance from corner in

recessed location-

Combustible - 6" (15.2cm)

Noncombustible - 2" (5.1cm)

Outside Corner Recessed Location

G = 12" (30.5cm) minimum clearance

Balcony with No Side Wall

Combustible &

Noncombustible

H = 24" (61cm)

J = 20" (50.8cm)

Balcony with Perpendicular Side Wall

Termination Clearances for Buildings with Combustible and Noncombustible Exteriors

Figure 10 - Minimum Clearances for Termination Cap

LOCATION OF TERMINATION CAP

www.desatech.com

116035-01E10

VENTING INSTALLATION

INSTRUCTIONS

   -

   -



These models are tested and approved for use

with DESA (direct-vent) pipe components and

terminations.

The venting system must terminate on the outside of

the structure and can not be attached to a chimney

or ue system serving a separate solid fuel or gas

burning appliance. A direct-vent appliance must

have its own venting system. DO NOT common

vent this appliance.

These models are approved to be vented either

horizontally through an outside wall or vertically

through a roof or chase enclosure using the fol-

lowing:

• When venting system terminates horizontally

on an outside wall, you may install a standoff

if the termination cap is to be installed directly

on a combustible nish such as vinyl, wood,

stucco, etc.

• Never run the vent downward as this may

cause excessive temperatures which could

cause a re.

• Vent pipe air space clearances to combustibles

are 1" on all sides except on the horizontal

sections, which requires 2" clearance from

the top of the pipe. Where the termination cap

penetrates a combustible wall, 1" air space

clearance is required.

• Have replace and selected vent components on

hand to help determine the exact measurements

when elbowing or offsetting. Always use wall

restops when penetrating walls and restops

when penetrating ceilings or attic spaces.

• Install horizontal venting with a 1/4" rise for

every 12" of run toward the termination.

WARNING: Read all instruc-



  

Failure to do so could result in





IMPORTANT: Do not seal vent cap to pipe. Cap

must be removable for servicing.

-





 

   



INSTALLATION

• Wear gloves and safety glasses for protection

• Use extreme caution when using ladders or

when on roof tops

• Be aware of electrical wiring locations in

walls and ceilings

The following actions will void the warranty on

your venting system:

• Installation of any damaged venting

component

• Unauthorizedmodicationoftheventingsys-

tem (Do not cut or alter vent components)

• Installation of any component part not

manufactured or approved by DESA

• Installation other than as instructed by these

instructions













   





    















www.desatech.com

116035-01E 11

INSTALLATION PLANNING

There are two basic types of direct-vent in-

stallation:

• Horizontal Termination

• Vertical Termination

Horizontal Termination Installation

IMPORTANT: Horizontal square terminations

require only inner portion of wall restop. Hori-

zontal installations using round termination require

exterior portion of wall restop (see Figure 20,

page 14).

1. Set the replace in its desired location and deter-

mine the route your horizontal venting will take.

Do not secure the replace until all venting has

been installed. Some installations require sliding

the replace in and out of position to make nal

venting connections. Figures 18 through 25 on

pages 13 through 16 show different congura-

tions for venting with horizontal termination that

will help you decide which application best suits

your installation. Check to see if wall studs or

roof rafters are in the path of your desired vent-

ing route. If they are, you may want to adjust the

location of the replace.

2. Direct vent pipe sections and components are

designed with special twist-lock connections.

 The female ends of the

pipes have locking lugs (indentations). These

lugs will slide straight into matching slots on

the male ends of adjacent pipes. Push pipe sec-

tions together and twist one section clockwise

approximately one-quarter turn until the sections

are fully locked (see Figure 11). Note: Horizon-

tal runs of vent must be supported every three

feet. Use wall straps for this purpose.

3. Any straight pipe section, a 45° or 90° elbow

can be used when rst connecting the venting

system to the replace. Elbows are designed

to twist-lock into any of four 90° positions to

direct the venting system to the desired loca-

tion. IMPORTANT: Do not attempt to alter

the conguration of the elbow by cutting,

twisting, bending, etc.

4. Assemble the desired combination of pipe and

elbows to the replace ue collar. If there are

long portions of venting run, pre-assembled

pipe sections may be installed as subassem-

blies for convenience.

VENTING INSTALLATION

INSTRUCTIONS

Continued

Figure 11 - Vent Pipe Connections

Female

Locking Lugs

Male

Slots

(Framing

Detail)

(273 mm)

" Inside Framing

(273 mm)

(216 mm)

Vent Opening

Combustible Wall

Vent Opening

Noncombustible Wall

Figure 12 - Vent Opening Requirements

Center of

Hole

5. Carefully determine the location where the vent

pipe assembly will penetrate the outside wall.

The center of the hole should line up with the

center-line of the horizontal vent pipe. Mark the

wall for a 10

/4" x 10

/4" square hole. Cut and

frame the square hole in the exterior wall where

the vent will be terminated. If the wall being

penetrated is constructed of noncombustible

material, such as masonry block or concrete,

a 8

/2" hole with zero clearance is acceptable

(see Figure 12).

www.desatech.com

116035-01E12

VENTING INSTALLATION

INSTRUCTIONS

Continued

WARNING: Do not recess





6.  Position the

horizontal vent cap in the center of the 8

round hole and attach to the exterior wall with

four wood screws provided. Before attaching

the vent cap to exterior wall, run a bead of

non-hardening mastic (pliable sealant) around

the outside edges to make a seal between it and

the outside wall. Note: The four wood screws

provided should be replaced with appropriate

fasteners for stucco, brick, concrete or other

types of sidings (see Figure 13).

 For vinyl siding,

stucco or wood exteriors, a siding standoff

may be installed between the vent cap and

exterior wall. The siding standoff prevents

excessive heat from damaging the siding

materials. Siding material must be cut to

accommodate standoff. Bolt the vent cap to

the standoff. Apply non-hardening mastic

around outside edge of standoff. Position the

standoff/cap assembly in the center of the 10

" square hole and attach to exterior wall

with wood screws provided (see Figure 14).

The siding standoff must sit ush against the

exterior fascia material.

7.  Fit the outer

and inner wall restop into the wall before

connecting horizontal run to vent cap (see

Figure 15).

Figure 13 - Installing Horizontal Vent Cap

(Noncombustible Exterior)

Wood Screw

Vent Cap

Figure 14 - Installing Siding Standoff

(Combustible Exterior Wall)

Cut Siding Away

to Fit Standoff

Screws

Standoff

Vent

Cap

Apply Mastic

to All Four Sides

8. Carefully move replace, with vent assembly

attached, toward wall and insert vent pipe

into horizontal termination. The pipe overlap

should be a minimum of 1

9.  Slide wall

restop against interior wall surface and attach

with screws provided (see Figure 16, page

13). See Figure 17, page 13, for horizontal

termination details.

10. Place replace into position and shim with

noncombustible material, if needed. Nail or

screw side anges to framing to secure unit in

place. IMPORTANT: Make sure replace is

level before securing. If replace is not level

it will not work properly.



 

   



Figure 15 - Installing Outer Wall Firestop

(Combustible Exterior Wall)

Inner Wall

Firestop

Inner Wall

Firestop

Inner Wall

Firestop

www.desatech.com

116035-01E 13

Figure 16 - Installing Inner Wall Firestop

VENTING INSTALLATION

INSTRUCTIONS

Continued

Figure 17 - Typical Horizontal

Termination Cap Mounting with

Additional Siding Standoff Installed

Siding Standoff

Screws

High Wind

Termination

Apply

Mastic to

Outside

Edge of

Standoff

Exterior Wall with Vinyl Siding

" x 10

Framed Opening

Maintain 1"

Minimum Air

Space Around

Outer Pipe When

Penetrating a Wall

Minimum Pipe

Overlap 1

Wall

Firestop

Direct-Vent

Pipe

WARNING: Never run vent

downward as this may cause

  



-

   







Figures 18 through 25 show different congura-

tions and alternatives for venting with horizontal

termination. Each figure includes a chart with

critical minimum and maximum dimensions which

MUST be met. IMPORTANT: Remember that a

horizontal run of venting must have a 1/4" rise for

every 12" of run toward the termination.

GROUND FLOOR INSTALLATION REAR VENT

Recommended Applications fo Rear Vent Model

(V)CD36R:

• Installation using cabinet surrounds

• Through the wall using round or square termi-

nation (up to a maximum of 18” of horizontal

pipe)

• Corner installation (Using one 45° elbow and

a maximum of 18" of horizontal pipe).

Figure 18 - Horizontal Termination

Congureation for Flush Installation

(Model (V)CD36R)

Inner Wall

Firestop

Vent

Cap

Pipe

Section

Horizontal

Square

Termination

Wall Firestop

Straight/Adjustable

Pipe 18" Max.



 

" Min. 22" Max

www.desatech.com

116035-01E14

GROUND FLOOR INSTALLATION

Recommended Applications for Rear Vent Model

(V)CD36T:

• Installation using cabinet surrounds

• Through the wall using round or square

termination (up to 24" horizontal pipe)

• Corner installation (Using one 90° elbow and

a maximum of 24" of horizontal pipe)

VENTING INSTALLATION

INSTRUCTIONS

Continued

Figure 20 - Horizontal Termination

Conguration Round Termination

(Model (V)CD36T)

Figure 19 - Horizontal Termination

Conguration for Corner Installation

(Model (V)CD36R)

Figure 21 - Horizontal Termination

Conguration For Corner Installation

Using One 90° Elbow (Model (V)CD36T)

Figure 22 - Horizontal Termination

Conguration with Vertical Rise and One

90° Elbow (Model (V)CD36T)













" None 26" Max.

" Min. 1 ft. 30" Max.

" Min. 2 ft. 74" Max.

" Min. 3 ft. 98" Max.

94" Min. 4 ft. 122" Max.

106" Min. 5 ft. 146" Max.

159" Min. 9 ft. 20' Max.

Horizontal Square

Termination

Wall

Firestop

Straight/Adjustable

Pipe 18" Max.



 

" Min. 24" Max

45°

Elbow

Wall

Firestop

Horizontal

Round

Termination

Exterior

Portion of Wall

Firestop (Round

Termination Only)

90°

Elbow

Wall

Firestop

Straight/

Adjustable

Pipe 24" Max.

Horizontal

Square

Termination

90°

Elbow



 

" Min. 32

" Max

90° Elbow

Wall

Firestop

Square

Termination

Not to Exceed

(H) Limits

Required

for (V),

See Chart

for Pipe

Section

Required

www.desatech.com

116035-01E 15

SNORKEL TERMINATION INSTALLATION

Recommended Applications Models (V)CD36R

and (V)CD36T:

• Installations requiring vertical rise on building

exterior.

• Installation using snorkel termination to achieve

1 ft. above grade.

VENTING INSTALLATION INSTRUCTIONS

Continued

Figure 23 - Snorkel Termination Conguration For Below Ground Installation

HORIZONTAL VENT INSTALLATIONS

USING MULTIPLE 90° ELBOWS (V)CD36T

TOP VENT

The following congurations show the minimum

vertical rise requirements for a horizontal system

using two 90° elbows.

Figure 24 - Horizontal Termination Conguration For Venting Using Two 90° Elbows

(Model (V)CD36T)







Horizontal (H



7' Min. 10' Max

8' Min. 12' Max

9' Min. 14' Max

10' Min. 16' Max

11' Min. 18' Max

13' Min. 20' Max

Snorkel terminations are available for installations

requiring a vertical rise on the exterior of the build-

ing. If installing snorkel below grade

you must provide proper drainage to prevent water

from entering snorkel (see Figure 23, page 15). Do

not back ll around snorkel termination.

90°

Elbow

90°

Elbow

Snorkel

Termination

12"

Min.

12" Min.

Adequate

Drainage

Snorkel

Termination

Snorkel

Termination

90° Elbow

12" Min.

Wall

Firestop

www.desatech.com

116035-01E16

VENTING INSTALLATION INSTRUCTIONS

Continued

Figure 25 - Horizontal Termination Conguration for Venting Using Three 90° Elbows

(Model (V)CD36T)



TERMINATION

Note: Vertical restrictor must be installed in all

vertical installations.

1. Determine the route your vertical venting

will take. If ceiling joists, roof rafters or other

framing will obstruct the venting system,

consider an offset (see Figure 26) to avoid cut-

ting load bearing members. Note: Pay special

attention to these installation instructions for

required clearances (air space) to combustibles

when passing through ceilings, walls, roofs,

enclosures, attic rafters, etc. Do not pack air

spaces with insulation. Also note maximum

vertical rise of the venting system and any

maximum horizontal offset limitations.

2. Set the replace in desired location. Drop a

plumb line down from the ceiling to the posi-

tion of the replace exit ue. Mark the center

point where the vent will penetrate the ceiling.

Drill a small locating hole at this point.

Drop a plumb line from the inside of the roof

to the locating hole in the ceiling. Mark the

center point where the vent will penetrate the

roof. Drill a small locating hole at this point.

Figure 26 - 45° and 30° Offset with Wall

Strap



 



Horizontal (H



5' Min. 2' Max. 6' Max

6' Min. 3' Max. 8' Max

7' Min. 4' Max. 10' Max

8' Min. 5' Max. 12' Max

12' Min. 8' Max. 20' Max

20' Min. 8' Max. 20' Max

90°

Elbow

90°

Elbow

90°

Elbow

Roof

Flashing

Wall

Strap

45°

Elbows

WS-58

Wall Strap

2 - 2 x 4

Vertical

Header

OSR58-30

30° Offset

Return

Horizontal

Frame Member

www.desatech.com

116035-01E 17



Cut a 10

" square hole in the ceiling using

the locating hole as a center point. The opening

should be framed to 10

" x 10

" (273 mm x

273 mm) inside dimensions, as shown in Figure

12 on page 11 using framing lumber the same

size as the ceiling joists. If the area above the ceil-

ing is an insulated ceiling or a room, nail restop

from the top side. This prevents loose insulation

from falling into the required clearance space.

Otherwise, install restop below the framed hole.

The restop should be installed with no less than

three nails per side (see Figure 27).

2. Assemble the desired lengths of pipe and

elbows necessary to reach from the replace

ue up through the restop. Be sure all pipe

and elbow connections are fully twist-locked

(see Figure 11, page 10).

3. Cut a hole in the roof using the locating hole

as a center point. (Cover any exposed open

vent pipes before cutting hole in roof.) The

" x 10

" hole must be measured on

the horizontal; actual length may be larger

depending on the pitch of the roof. There

must be a 1" clearance from the vent pipe to

combustible materials. Frame the opening as

shown in Figure 12, page 11.

VENTING INSTALLATION

INSTRUCTIONS

Continued

Figure 27 - Installing Firestop

If area above is not a room, install restop

below framed hole.

If area above is a room or insulated area,

install restop above framed hole.

4. Connect a section of pipe and extend up

through the hole.

Note: If an offset is needed to avoid obstruc-

tions, you must support the vent pipe every

3 feet. Use wall straps for this purpose (see

Figure 26, page 16). Whenever possible, use

45° elbows instead of 90° elbows. The 45°

elbow offers less restriction to the ow of the

ue gases and intake air.

5. Place the ashing over the pipe section(s)

extending through the roof. Secure the base of

the ashing to the roof and framing with roof-

ing nails. Be sure roong material overlaps the

top edge of the ashing as shown in Figure 26,

page 16. There must be a 1" clearance from

the vent pipe to combustible materials.

6. Continue to add pipe sections until the height

of the vent cap meets the minimum building

code requirements described in Figure 10 on

page 8. Note: You must increase vent height

for steep roof pitches. Nearby trees, adjoining

rooines, steep pitched roofs and other similar

factors may cause poor draft or down-drafting

in high winds. Increasing the vent height may

solve this problem.

7. Twist-lock the vent cap onto the last section

of vent pipe.

Note: If the vent pipe passes through any occupied

areas above the rst oor, including storage spaces

and closets, you must enclose pipe. You may

frame and sheetrock the enclosure with standard

construction material. Make sure and meet the

minimum allowable clearances to combustibles.

Do not ll any of the required air spaces with

insulation.

www.desatech.com

116035-01E18

VENTING INSTALLATION

INSTRUCTIONS

Continued





Figures 28 and 29 show two different congura-

tions for vertical termination.

VERTICAL VENT INSTALLATIONS USING

MULTIPLE 90° ELBOWS (V)CD36R REAR

VENT

Figure 28 - Vertical Venting

Conguration using One 90° Elbow

(Model (V)CD36R with Vertical Round

High Wind Termination)

Figure 29 - Vertical Venting

Conguration using Three 90° Elbows

(Model (V)CD36R with Vertical Round

High Wind Termination)









Horizontal













Horizontal (H



8' Min. 2' Max. 12' Min. 8' Max

8' Min. 2' Max. 14' Min. 11' Max

8' Min. 2' Max. 16' Min. 14' Max

8' Min. 2' Max. 18' Min. 17' Max

8' Min. 2' Max. 20' Min. 20' Max

8' Min. 2' Max. 40' Min. 20' Max

Note: Vertical (V

) + Vertical (V

) = 40' Max.

Max. Horizontal Above 20' Vertical = 20'



 

8' Min. 2' Max

40' Min. 2' Max

90°

Elbow

90°

Elbow

90°

Elbow

Note: Install a

VR-58 vertical

restrictor ring

into inner pipe

section prior to

attaching vent

termination

cap.

Note: Install a

VR-58 vertical

restrictor ring

into inner pipe

section prior to

attaching vent

termination

cap.

www.desatech.com

116035-01E 19

VENTING INSTALLATION

INSTRUCTIONS

Continued





Figures 30 and 33 show four different congura-

tions for vertical termination.

VERTICAL VENT INSTALLATIONS USING

MULTIPLE 90° ELBOWS (V)CD36T TOP

VENT

Figure 31 - Vertical Venting

Conguration Using Two 90° Elbows

(Model (V)CD36T with Vertical Round

High Wind Termination)

Figure 32 - Vertical Venting

Conguration Using Two 90° Elbows

(Model (V)CD36T with Vertical Round

High Wind Termination)

Note: Vertical (V

) + Vertical (V

) = 40' Max.

Max. Horizontal Above 14' Vertical = 20'

Figure 30 - Vertical Venting

Conguration using Three 90° Elbows

(Model (V)CD36T with Vertical Round

High Wind Termination)











Horizontal



8' Min. 9' Max

9' Min. 11' Max

10' Min. 13' Max

12' Min. 17' Max

14' Min. 20' Max





Horizontal (H



Horizontal (H



8' Min. 5' Max

10' Min. 8' Max

12' Min. 11' Max

14' Min. 14' Max

16' Min. 17' Max

18' Min. 20' Max

40' Min. 20' Max



 

8' Min. 6' Max

9' Min. 8' Max

10' Min. 10' Max

12' Min. 14' Max

14' Min. 18' Max

40' Min. 20' Max

Note: Install a

VR-58 vertical

restrictor ring

into inner pipe

section prior to

attaching vent

termination

cap.

90° Elbow

Note: Install a

VR-58 vertical

restrictor ring

into inner pipe

section prior to

attaching vent

termination

cap.

90° Elbow

Note: Install a

VR-58 vertical

restrictor ring

into inner pipe

section prior to

attaching vent

termination

cap.

www.desatech.com

116035-01E20







 

P58-6 6" Section Double Wall Pipe,

Galv.

P58-12 12" Section Double Wall Pipe,

Galv.

P58-24 24" Section Double Wall Pipe, Galv.

P58-36 36" Section Double Wall Pipe, Galv.

P58-48 48" Section Double Wall Pipe,

Galv.

PA58-712 Adjustable 7"-12" Section Double

Wall Pipe, Galv.

E58-45 45° Elbow, Galv.

E58-90 90° Elbow, Galv.

VENTING INSTALLATION

INSTRUCTIONS

Continued

 

VKG-58 Ground Floor Vent Kit, Galvanized

(Includes: 45° Elbow, 7"-12"

Adjustable Pipe, Wall Firestop,

Horizontal Square Termination,

16 Screws)

VKB-58 Basement Vent Kit, Galvanized

(Includes: 45° Elbow, 7"-12"

Adjustable Pipe, Wall Firestop,

Horizontal Square Termination,

4' Pipe, 90° Elbow, 20 Screws)

VKS-58 Snorkel Vent Kit, Galvanized

(Includes: 45° Elbow, 7"-12"

Adjustable Pipe, Wall Firestop,

36" Snorkel Termination, 4' Pipe,

1' Pipe, 90° Elbow, 26 Screws)

VKR-58 R oo f Ve nt K i t, G a lv a ni z ed

(Includes: 45° Elbow, 7"-12"

Adjustable Pipe, Flue Restrictor,

Vertical High Wind Termination,

2' Pipe, 4' Pipe, Wall Firestop,

Storm Collar, Roof Flashing

[0/12 - 6/12], 26 Screws)

VKC-58 Corner Vent Kit, Galvanized

(Includes 45° Elb o w, 7"-1 2"

Adjustable Pipe, Wall Firestop,

Horizontal Termination, 6" Pipe,

90° Elbow, 18 Screws)

HHTK-58 High Wind Round Horizontal

Termination Kit (Includes Round

Termination, Wall Firestop, 45°

Elbow)

HHT-58 High Wind Round Horizontal

Termination Kit, Galv.

HTS-58 Horizontal Square Termination, Galv.

HTKS-58 Horizontal Square Termination Kit

(Includes: Square Termination,

Wall Firestop, 45° Elbow)

VT-58 Vertical Round Termination, Galv.

ST-58-14 14" Snorkel Termination, Galv.

ST-58-36 36" Snorkel Termination, Galv.

SC-58 Storm Collar, Galv.

WF-58 Wall Firestop, Galv.

RF-58-6 Roof Flashing - 0 to 6/12 Pitch,

Galv.

RF-58-12 Roof Flashing - 6/12 to 12/12 Pitch,

Galv.

VR-58 Vertical Restrictor, Galv.

S-58 Vinyl Siding Standoff, Galv.

WS-58 Wall Strap

CS-58 Cathedral Ceiling Support

FP-58 Firestop Plate

SF-58 Stucco Flashing -

For use with HTS-58

RF-58 Flat Roof Flashing

OSR58-30 30° Offset Return

Figure 33 - Vertical Venting

Conguration with No Horizontal Run

(Model (V)CD36T with Vertical Round High

Wind Termi

nation)



V = 40' Max.

Note: Install a

VR-58 vertical

restrictor ring

into inner pipe

section prior to

attaching vent

termination cap.

Note: Install an

OSR58-30 30°

offset return

with WS-58 wall

strap supports

as necessary

to maintain 1"

Clearance to all

horizontal wood

frame members.

WS-5 8

Page is loading ...

Desa (V)CD36RP User manual

Related papers

Other documents