Comnet NWAVBSA1 Quick start guide
- Category
- Network antennas
- Type
- Quick start guide
INS_NW1_NW2_QS_REV– 05/20/13 PAGE 1
QUICK START GUIDE
NWAVBSA1
EXTERNAL DUAL POLARIZATION
VARIABLE BEAM SECTOR ANTENNA
Thank you for purchasing Netwave
®
from ComNet. This quick start guide is designed to
walk you through installation of the NWAVBSA1 Variable Beam Sector Antenna in an
application using the NetWave® NW(1,2)R2 industrially hardened dual radio
wireless ethernet device.
This manual serves the following
ComNet Model Number:
NWAVBSA1
INS_NW1_NW2_QS_REV– 05/20/13 PAGE 2
FIGURE 1 – NW1/NW2 INDUSTRIAL WIRELESS ETHERNET LINK
QUICK START USER GUIDE NWAVBSA1
BACKFRONT
TECH SUPPORT: 1.888.678.9427
Mounting Bracket
Beamwidth Adjuster
Locking Pin
N-Type Connectors
(shown with dust caps)
FIGURE 2 - RF PATTERNS
60º Horizontal 90º Horizontal 120º Horizontal Vertical, Typical
INS_NW1_NW2_QS_REV– 05/20/13 PAGE 3
FIGURE 3 – INSTALLATION INSTRUCTIONS
QUICK START USER GUIDE NWAVBSA1
TECH SUPPORT: 1.888.678.9427
Step 1.
Unpack the hardware from the box. The pre-assembled mount is designed to support poles up to 3" in diameter.
Remove the bracket and screws from the mount in order to more easily reach the N-type connectors and black Rear Tube.
Step 3.
Set the depth of the Adjuster according to the desired
beamwidth. Align the holes in the Beamwidth Adjuster with the
gray Back Housing.
60º - Beamwidth Adjuster set to third hole position.
90º - Beamwidth Adjuster set to middle hole position.
120º - Beamwidth Adjuster set to first hole position (pressed all
the way in).
Note: If two Beamwidth Adjusters are being used, both should be
set the same for accurate beam width.
60º 90º 120º
Step 5.
Connect both included cables from the N-type connector on
the NetWave® NW(1,2)R2 external antenna connector to the
corresponding connector on the NWAVBSA1.
Step 4.
Replace the Locking Pin through the Back Housing and
Beamwidth Adjuster and position the clip on the right side to
secure it.
Step 2.
Remove the Locking Pin from the black Beamwidth Adjuster by
unclipping the right side first, sliding the pin to the left until it exits
the gray Back Housing and hangs free (the wire attached to the
Back Housing will prevent loss).
INS_NW1_NW2_QS_REV– 05/20/13 PAGE 4TECH SUPPORT: 1.888.678.9427
QUICK START USER GUIDE NWAVBSA1
FIGURE 4 – POLE MOUNT INSTALLATION GUIDE
The pole mount bracket is installed at time of shipment. Unfold the bracket assembly away from the body of the antenna to allow
access to the connectors and beamwidth selector.
Mount antenna to pole via the bracket, noting the orientation of the hardware in photos below. Adjust the vertical tilt of the
antenna and tighten all bolts to secure.
The included Mounting kit is designed to support poles from 2.0in (5cm) to 2.75in (7cm) in diameter.
INS_NW1_NW2_QS_REV– 05/20/13 PAGE 5TECH SUPPORT: 1.888.678.9427
QUICK START USER GUIDE NWAVBSA1
FIGURE 5 – REDUNDANT RING TOPOLOGY (SHOWN WITH POE CAMERAS)
FIGURE 6 – DROP-AND-REPEAT TOPOLOGY (SHOWN WITH 24VAC POWERED CAMERAS)
NW1R2
IP Camera
IP Camera
NW1 (Client)
IP Camera
NW1R2
NWAVBSA1
External Antenna
NWAVBSA1
External Antenna
NW1 (Access Point)
PoE
PIM
PIM
PIM
ComNet Managed
Switch with 30W PoE
Connected to Network
Building or Other Obstacle
24VAC
24VAC
24VAC
PIM
PIM
NW1R2POE
NW1R2POE
STP Blocked
Port
NWAVBSA1
External Antenna
NWAVBSA1
External Antenna
NWAVBSA1
External Antenna
NWAVBSA1
External Antenna
PoE Camera
PoE Camera
PoE Camera
NW1R2
NW1R2POE
PoE
PoE+
PoE+
PoE+
ComNet Gigabit
Managed Switch
providing 30W PoE
ComNet Gigabit
Managed Switch
providing 30W PoE
INS_NW1_NW2_QS_REV– 05/20/13 PAGE 6
QUICK START USER GUIDE NWAVBSA1
© 2013 Communications Networks Corporation. All Rights Reserved. “ComNet,” the “ComNet Logo,” “Netwave,” and the “Netwave Logo” are registered trademarks of Communication Networks, LLC.
3 CORPORATE DRIVE | DANBURY, CT 06810 | USA
T: 203.796.5300 | F: 203.796.5303 | TECH SUPPORT: 1.888.678.9427 | INFO@COMNET.NET
8 TURNBERRY PARK ROAD | GILDERSOME | MORLEY | LEEDS, UK LS27 7LE
T: +44 (0)113 307 6400 | F: +44 (0)113 253 7462 | INFO-EUROPE@COMNET.NET
Need Additional Assistance?
Visit our website http://www.comnet.net or contact Comnet tech support:
Tel: (203) 796-5300
Toll free: (888) 678-9427
Email: [email protected]
Additional Technical support contact details can be found at:
http://www.comnet.net/services/technical-support.html
Or Visit our pre-sales design center:
http://www.comnet.net/services/design-center.html
Or our customer care:
http://www.comnet.net/services/customer-care.html
Additional Downloads
Datasheets, Installation manuals and other product documentation can be found at:
http://www.comnet.net/comnet-products/ethernet/wireless/
-
1
-
2
-
3
-
4
-
5
-
6
Comnet NWAVBSA1 Quick start guide
- Category
- Network antennas
- Type
- Quick start guide
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Comnet PS24AC12DC User manual
-
-
-
-
-
-
-
Comnet FVT/FVR8SFP2R User manual
-
-