Carbine Carbine PL80 Owner's manual

Carbine PL80
Brand
Carbine
Model
Carbine PL80
Category
Remote starters
Type
Owner's manual

This manual is also suitable for

OWNER'S MANUAL
Remote Control Auto Starter
with Security and Keyless Entry
This device complies with part 15 of the FCC rules.
Operation is subject to the following two conditions:
[1] This device may not cause harmful interference; and
[2] This device must accept any interference received,
including interference that may cause undesired operation.
Note: The manufacturer is not responsible for any radio or TV
interference caused by unauthorized modifications to this equipment.
Such modifications could void the user's authority to operate the equipment.
Model START2-PLUS
R
START2 UM 3/5/02 2:31 PM Page 1
2
Warnings
Remote Control Transmitters
Remote Security and Keyless Entry Operation
Congratulations!
On your purchase of our Unique Remote Auto Starter with Keyless Entry and Security System. Please read
the enclosed operating instructions to insure you enjoy the numerous benefits available to you.
As with any product that performs automatic functions, there are certain safety precautions that you must
practice and be aware of.
1. Keep the transmitter[s] out of children’s reach.
2. Do not leave anyone in the vehicle while running on remote control.
3. Alert servicing personnel that the vehicle can be started automatically.
4. Do not start the vehicle by remote while it’s in an enclosed area or garage.
5. Always apply the parking brake and lock the vehicle as you exit the vehicle.
6. Should the unit malfunction, disconnect the fuse until the problem is corrected.
7. The use and operations of this system is the sole responsibility of the operator.
8. This system is designed for a fuel-injected vehicle with an automatic transmission.
9. This system must be installed and wired through a safety switch so it will not start in any forward or
reverse gear.
10. This system shall never be installed on a vehicle with a manual transmission.
11. Some areas may have local ordinances that prohibit leaving a vehicle running on public streets.
• The system has an operating range of up to approximately 1,000 ft.
• Two 4-button code hopping transmitters are included for your convenience.
• Keep the transmitters dry. Do not submerge them in water.
• Loss or abuse to the transmitters or to its case is not warranted.
• Under normal use, the batteries will last about one year. [Uses A23 type]
To Arm the Alarm and Lock the Doors:
• Exit the vehicle and depress the “LOCK” button on the transmitter once.
• The siren/horn will chirp once, parking lights will flash once, the doors will “LOCK” and the LED will
begin flashing.
• The alarm is now armed.
• If your security system becomes triggered, the parking lights will flash and the alarm will sound for 60
seconds and reset. If a door is left open, the system will sound for two more 60-second cycles. The
alarm will fully rearm and then ignore the door trigger zone. Closing the door will re-set the door
trigger zone.
Note: If the dome light is on at the time, you arm the alarm you will hear another short chirp about [4]
seconds later to indicate a protected zone is being violated. This is very common on vehicles with
factory delayed interior lights. The alarm will arm the door trigger zone after the interior lights go off.
Because your vehicle is equipped with an shock sensor, you may experience the above symptoms
depending on how sensitive the sensor is set and how hard the door was closed. The alarm will arm the
shock sensor once the zone is cleared.
R
LOCK
UNLOCK
PANIC
START
START2 UM 3/5/02 2:31 PM Page 2
3
Valet Mode and Emergency Disarm Procedure
Remote Security and Keyless Entry Operation (Continued)
To Disarm the Alarm and Unlock the Doors:
• Depress the “UNLOCK” button on the transmitter once.
• The interior lights will turn “ON”, siren/horn will chirp twice, parking lights will flash twice, the doors
will “UNLOCK” and LED will stop flashing.
The interior lights will turn “ON” for 30 seconds or until the ignition key is turned “ON”. If you have the
drivers door “UNLOCK” first option, depress the “UNLOCK” button two times to “UNLOCK” the other
doors. The interior light activation and/or arming/disarming chirps can be programmed off permanently,
if desired.
User Discretion Silent Arming and Disarming:
This feature allows you to retain the normal arm/disarm chirps and allows you to arm/disarm silently.
• To arm or disarm without chirps, depress both the “LOCK” and “UNLOCK” buttons at the same time.
Remote Trunk/Rear Hatch Release:
• Depress and hold the “UNLOCK” button for 3 seconds.
• The alarm will disarm and the trunk/rear hatch will open.
Note: This is a separate extra cost option and the vehicle must have an electric trunk release to have this
feature.
Remote Personal Panic Feature:
When panic is activated, the parking lights flash and the siren/horn sounds.
To Activate: Depress the “PANIC” or “LOCK” button for [3] seconds or more.
To Deactivate: Depress the “PANIC” button again or depress the “UNLOCK” button.
Note:
The siren/horn will sound and the lights will flash for [1] minute and reset, if you do not turn “OFF”
panic.
To Lock The Vehicle Without Arming Our Security System:
• Simply “LOCK” the doors using the factory power door lock switch as you exit.
• To use our remote to “UNLOCK” the doors later, depress the “UNLOCK” button.
To Turn the Security Features Off [Valet Mode] or to Disarm the Alarm Without Using the Remote
Transmitter [Emergency Disarm]:
• Turn “ON” the ignition key.
• The system begins looking for Valet switch input data for 30 seconds.
• Switch the valet switch to the “ON” position until the LED illuminates. [2 seconds]
• Once the LED illuminates it indicates that the alarm is now in valet mode.
• Switch the valet switch to the “OFF” position.
• Turn “OFF” the ignition key. The LED begins flashing once every 5 seconds.
• When the ignition key is “ON”, the LED will be on steady to remind you that the alarm is in valet mode.
• While in valet mode the remote starter and remote keyless entry features will operate normally
including the “LOCK/UNLOCK” parking light flash confirmation. However, there is no security
protection and no brake pedal depressed door locking or ignition controlled unlocking.
• The emergency disarm procedure is the same procedure as the valet mode. However, please note that
the alarm will begin sounding [if armed] immediately when you open the door. Enter the vehicle [with
alarm sounding], turn on the ignition, depress and hold the program switch in until the alarm stops
sounding [for approximately 2 seconds]. The alarm will remain in valet mode until you turn the security
features back “ON”.
START2 UM 3/5/02 2:31 PM Page 3
Remote Auto Starter Operation
To Remote Start the Vehicle:
• Depress the “BLUE” button for approximately 1 to 2 seconds.
• The parking lights will activate to indicate the remote start received the signal.
• The ignition circuits will activate and the engine will start approximately [5] seconds later.
• Once the engine is running on remote control, the climate controls will activate and adjust the vehicles
interior temperature to your preset settings.
• The vehicle will run for the 14 or 21 minute cycle and automatically turn “OFF”.
To Turn Off the Remote Starter:
• Depress the blue start button for (3) seconds to turn “OFF” the engine.
4
Valet Mode and Emergency Disarm Procedure (Continued)
To Turn the Security Features Back On:
• Turn “ON” the ignition key.
• The system begins looking for the valet switch input data for 30 seconds.
• Switch the Valet switch to the “ON” position until the LED turns “OFF”. [for 2 seconds]
• Switch “OFF” the valet switch.
• Turn “OFF” the ignition key.
•
The security system will now arm/disarm as you “LOCK/UNLOCK” the vehicle with the remote transmitter.
Automatic Door Locking and Unlocking Operation
We have incorporated special features to insure maximum driver/occupant safety while operating the
vehicle along with safeguards to prevent you from being locked out accidentally.
• The doors will “LOCK” when you depress the brake pedal. (Provided the ignition key is turned “ON”
and the doors are closed)
• The doors will “UNLOCK” immediately when the ignition key is turned “OFF”.
• If you stop to pick up or drop off a passenger, the doors will automatically re-lock upon the next
application of the brake pedal after the door is re-closed.
• The automatic door “LOCK/UNLOCK” feature does not operate in valet mode.
• The automatic door “LOCK/UNLOCK” feature can be programmed “OFF”.
LED Status Indicator and Violation Report
The LED indicator provides information on [7] modes of security system operation.
1. LED is “OFF” = Security system is disarmed.
2. LED is flashing steady = Security system is armed.
3. LED is flashing fast = Automatic arming timer is counting down.
4. LED is on solid with ignition key turned “ON” = Security system is in valet mode.
5. LED is flashing once every 5 seconds when ignition key is “OFF” = System is in valet mode.
6.
LED is flashing in a [2] flash-pause sequence = System was triggered by the hood switch or a shock sensor.
7. LED is flashing in a [3] flash-pause sequence = System was triggered from an opened door.
Note:
The [2] or [3] flashing-pause tamper alert memory will be cleared when you turn “ON” the ignition key.
When disarming if you receive [4] siren/horn chirps it indicates the alarm was triggered during your
absence.
START2 UM 3/5/02 2:31 PM Page 4
Safety Features
Remote Auto Starter Operation (Continued)
To Operate The Vehicle While Running on the Remote Starter:
• Depress the “UNLOCK” button to unlock the doors and disarm the alarm.
• Insert and turn “ON” the ignition key [two positions] and drive “OFF”.
• When you depress the brake pedal, the remote starter will turn “OFF”. Therefore, if you accidentally
depress the brake pedal before you turn “ON” the ignition key, the remote starter will turn “OFF” and
the engine will die. If this happens, simply restart the engine with the ignition key and drive “OFF”.
Temporary Stop Feature:
This feature allows you to exit and leave the vehicle running on remote control.
To activate this feature:
1. Stop the vehicle, place the transmission in park and set the parking brake.
2. With the vehicle still running on the ignition key, depress the “BLUE” button to activate the remote
starter.
(Do not depress the brake pedal.)
3. The parking lights will come “ON” when the remote starter activates.
4. Turn “OFF” and remove the ignition keys. The engine will stay running.
5. Exit the vehicle. Be sure to take the ignition keys/remote transmitter with you.
6. Depress the remote control “LOCK” button to secure the vehicle.
7. The vehicle will continue to run for 14 or 21 minutes.
The vehicle can not be driven until the ignition key is used to unlock the steering column. To prevent bodily
harm, attempted theft or vehicle damage, the remote starter will turn “OFF” if:
• The hood is raised.
• The alarm becomes triggered.
• The brake pedal is depressed.
• Engine is over-revved. [tach mode only]
• Upon the expiration of the 14 or 21 minute programmed run time.
• The vehicle refused to start running after [3] unsuccessful attempts.
5
Automatic Timed Start Operation
This feature allows you to program the vehicle to automatically start every 3 hours for 6 cycles. For safety
reasons the timed start mode automatically cancels each time you operate the vehicle.
To Activate the Automatic Timed Start Mode:
1. Start the vehicle by remote control. (The vehicle must be running on remote control)
2. Rapidly depress the start button on the transmitter (3) times within 3 seconds. The LED will flash
(3) times. The parking lights will flash “OFF” (3) times. The siren/horn will chirp (3) times.
3. The vehicle is now programmed to start every (3) hours.
4. In addition you can also start and turn “OFF” the vehicle more often using the remote transmitter.
To Deactivate the Automatic Timed Start Mode by Remote Control:
1. Start vehicle by remote control. (The vehicle must be running on remote control)
2. Rapidly depress the start button on the transmitter (3) times within 3 seconds. The LED will flash
(4) times. The parking lights will flash “OFF” (4) times. The siren/horn will chirp (4) times.
3. The vehicle is no longer programmed to start automatically.
START2 UM 3/5/02 2:31 PM Page 5
6
Feature Programming
To simplify the procedures we have divided the feature programming into four groups. Please review the
factory settings and decide if you require any changes. No programming can be performed while the
module is in valet mode.
Basic Overview on How to Perform Feature Programming:
• Turn “ON” the ignition key.
• Toggle the Valet switch the appropriate number of times for the group of features you want to change.
[6, 8, 10, or 15 times]
• Depress the “LOCK” and/or “UNLOCK” button to change the feature.
• Turn “OFF” the ignition key.
• The factory default settings is always [1] LED flash, [1] Parking light flash and [1] siren/horn chirp.
• Therefore, when you first depress the “LOCK” or “UNLOCK” button on the transmitter, it advances the
module to the next feature setting.
• In this case, the module would advance to [2] LED flashes, [2] parking light flashes and [2] siren/horn
chirps etc.
• Simply keep re-depressing the transmitter button again until the module advances to your desired
setting.
Transmitter Code Learning
To Enter Code Learning Mode: [The Module Learns Up To 4 Transmitter Codes]
1. Turn “ON” the ignition key.
2. Toggle the Valet switch “ON” and “OFF” 3 times within 30 seconds of turning on the ignition key.
3. The LED will be on solid and the siren/horn will emit [1] long chirp to indicate you are now in code
learning mode.
4. Depress the “LOCK” button on the first transmitter.
5. The LED will begin flashing slowly and the siren/horn will emit [1] short chirp.
6. Depress the “LOCK” button on the second transmitter.
7. The LED will flash slowly and the siren/horn will emit [1] short chirp.
8. Repeat the above steps [4] and [5] for the third and fourth transmitter if applicable.
9. Turn “OFF” the ignition key. The horn will emit [1] short and [1] long chirp to indicate you are out of
code learning.
Note: If a fifth transmitter is programmed in, it erases the first transmitter etc.
To Erase the Codes of A Lost or Stolen Transmitter:
1. Enter transmitter code learning as usual.
2. Depress the “LOCK” button on your [1] remaining transmitter [4] times.
3.
Alternatively you can purchase an additional transmitter and program in the [2] transmitters twice each etc.
4. The idea is to fill the memory bank with [4] codes to delete the old codes.
START2 UM 3/5/02 2:31 PM Page 6
7
Alarm Feature Programming
To Enter Alarm Feature Programming Mode:
1. Turn “ON” the ignition key.
2. Toggle the Valet switch ON/OFF [6] times within 30 seconds after turning “ON” ignition.
3. The LED and parking lights will flash [6] times. The siren/horn will chirp [6] times.
4. You are now in alarm feature programming.
Chirp Status [Factory Default Setting is “ON”]
The siren/horn emits [1] chirp upon a remote lock and [2] chirps upon a remote unlock signal. You can
permanently program these chirps “OFF”, if desired:
To Turn the Chirps “OFF”:
• Depress the “LOCK” button.
• The LED and parking lights will flash [2] times. The siren/horn will chirp [2] times.
To Turn the Chirps Back “ON”: [Factory Default Setting]
• Depress the “LOCK” button.
• The LED and parking lights will flash [1] time. The siren/horn will chirp [1] time.
Last Door Automatic Arming [Factory Default Setting is “OFF”]
The alarm can be programmed to automatically arm and to lock or not lock the doors 30 seconds after
you exit the vehicle.
To Turn the Automatic Passive Arming “ON” and Automatic Passive Door Locking “ON”:
• Depress the “UNLOCK” button.
• The LED and parking lights will flash [2] times. The siren/horn will chirp [2] times.
To Turn Automatic Passive Arming “ON” without Automatic Passive Door Locking:
• Depress the “UNLOCK” button.
• The LED and parking lights will flash [3] times. The siren/horn will chirp [3] times.
To Turn Automatic Passive Arming Feature Back “OFF”: [Factory Default Setting]
• Depress the “UNLOCK” button.
• The LED and parking lights will flash [1] time. The siren/horn will chirp [1] time.
Safety Illumination Sentinel System [Factory Default Setting is “OFF”]
This feature turns the parking lights “ON” for 12 seconds upon a lock signal and for 30 seconds upon an
unlock signal.
To Turn the Safety Sentinel Feature “ON”:
• Depress both the “LOCK” and “UNLOCK” buttons.
• The LED and parking lights will flash [2] times. The siren/horn will chirp [2] times.
To Turn the Safety Sentinel Feature Back “OFF”: [Factory Default Setting]
• Depress both the “LOCK” and “UNLOCK” buttons.
• The LED and parking lights will flash [1] time. The siren/horn will chirp [1] time.
START2 UM 3/5/02 2:31 PM Page 7
Automatic Door Locking and Unlocking Feature Programming
To Enter Door Lock and Unlock Feature Programming:
1. Turn “ON” the ignition key.
2. Toggle the Valet switch “ON” and “OFF” [8] times within 30 seconds after turning “ON” ignition.
3. The LED and parking lights will flash [8] times. The siren/horn chirps [8] times.
4. You are now in automatic door “LOCK” and “UNLOCK” feature programming mode.
Brake Pedal Depressed Door Locking [Factory Default Setting is “ON”]
The alarm can be programmed to “LOCK” or “NOT LOCK” the vehicle doors when the brake pedal is
depressed. The doors must be closed and the ignition key must be on for the brake pedal to “LOCK” the
doors. When in valet mode this feature does not work.
To Turn the Brake Pedal Door Locking Feature “OFF”:
• Depress the “LOCK” button.
• The LED and parking lights will flash [2] times. The siren/horn will chirp [2] times.
To Turn the Brake Pedal Door Locking Back “ON”: [Factory Default Setting]
• Depress the “LOCK” button.
• The LED and parking lights will flash [1] time. The siren/horn will chirp [1] time.
Ignition “OFF” Door Unlocking [Factory Default Setting is “ON”]
When the ignition key is turned “OFF” the doors will “UNLOCK”. The module can be programmed to not “UNLOCK” the
doors if desired.
To Turn the Ignition “OFF” Door Unlocking Feature “OFF”:
• Depress the “UNLOCK” button.
• The LED and parking lights will flash [2] times. The siren/horn will chirp [2] times.
To Turn the Ignition “OFF” Unlocking Feature Back “ON”: [Factory Default Setting]
• Depress the “UNLOCK” button.
• The LED and parking lights will flash [1] time. The siren/horn will chirp [1] time.
Note: The brake pedal door locking feature must be programmed “ON” in order to also have ignition
“OFF” unlocking. When in valet mode this feature does not work.
8
START2 UM 3/5/02 2:31 PM Page 8
Remote Starter Feature Programming
To Enter Remote Starter Feature Programming:
1. Turn “ON” the ignition key.
2. Toggle the Valet switch “ON” and “OFF” [10] times within 30 seconds after turning “ON” ignition.
3. The LED and parking lights will flash [10] times. The siren/horn chirps [10] times.
4. You are now in remote starter feature programming mode.
Remote Run Time with Gas or Diesel Engine [Default is 14 minutes and Gas Engine]
The module can be programmed for a 14 or 21 minute run time. In addition, the delay before cranking is
programmable for a gas or diesel engine. Gasoline engine setting is [5] second delay before cranking.
Diesel engine is [18] second delay.
For 14 Minute Runtime with a Gasoline Engine: [Factory Default Setting]
• Depress the “LOCK” button.
• The LED and parking lights will flash [1] time. The siren/horn will chirp [1] time.
For 21 Minute Runtime with a Gasoline Engine:
• Depress the “LOCK” button.
• The LED and parking lights will flash [2] times. The siren/horn will chirp [2] times.
For 14 Minute Runtime with a Diesel Engine:
• Depress the “LOCK” button.
• The LED and parking lights will flash [3] times. The siren/horn will chirp [3] times.
For 21 Minute Runtime with a Diesel Engine:
• Depress the “LOCK” button.
• The LED and parking lights will flash [4] times. The siren/horn will chirp [4] times.
Starter Release Circuitry [The Factory Default Setting is Voltage Mode]
You can program the Remote Starter for voltage, tachometer signal or fixed cranking time mode. For
voltage mode there are no extra hook-ups or additional programming required.
For Tachometer Mode:
For Tach mode, you must program our module to look for a tach signal. In addition, you must connect
our blue/white tach wire to the vehicle tach wire.
To Select the Tach Mode:
• Depress the “UNLOCK” button.
• The LED and parking lights will flash [2] times. The siren/horn will chirp [2] times.
• Start the engine with the ignition key and wait for the RPM's to slow down.
• Depress and hold in the program switch to learn the [RPM] tach signal.
• [The Parking lights will be “ON” steady while learning the RPM's]
• Once the module learns the RPM's, the LED and parking lights will flash [10] times. The siren/horn
will chirp [10] times.
• Release the program switch and turn “OFF” the ignition key to exit tach learning.
To Select Fixed Starter Cranking Mode:
• Depress the “UNLOCK” button.
• The LED and parking lights will flash [3] times. The siren/horn will chirp [3] times.
To Program the Remote Starter Back to Voltage Mode: [Factory Default Setting]
• Depress the “UNLOCK” button.
• The LED and parking lights will flash [1] time. The siren/horn will chirp [1] time.
9
START2 UM 3/5/02 2:31 PM Page 9
10
Remote Starter Feature Programming (Continued)
Code Hopping Technology [Factory Default Setting Is “ON”]
With code hopping technology “ON”, the receiver never accepts the same code twice. This makes your
system immune to code grabbers, therefore providing the highest level of security. With the code
hopping technology “OFF” you may experience somewhat improved range since the receiver does not
have to see all the bit stream information from the transmitter. However, the code could be intercepted
by a code grabber.
To Turn Code Hopping Technology “OFF”:
• Depress both the “LOCK/UNLOCK” button.
• The LED and parking lights will flash [2] times. The siren/horn will chirp [2] times.
To Turn Code Hopping Technology Feature Back “ON”: [Factory Default Setting]
• Depress both the “LOCK/UNLOCK” button.
• The LED and parking lights will flash [1] time. The siren/horn will chirp [1] time.
START2 UM 3/5/02 2:31 PM Page 10
To Enter Miscellaneous Feature Programming:
1. Turn “ON” the ignition key.
2. Toggle the valet “ON” and “OFF” switch [15] times within 30 seconds after turning “ON” the ignition.
3. The LED and parking lights will flash [15] times. The siren/horn chirps [15] times.
4. You are now in miscellaneous feature programming mode.
Panic Feature Operations [Factory Default Setting Allows Panic At All Times]
Some states forbid the operation of a siren while a vehicle is operating. The module can be programmed
to prevent panic operations when the ignition is “ON”. In addition, the panic feature can be programmed
“OFF “ and no longer respond to the panic button of the transmitter, if desired.
To Prevent Remote Panic Activation when the Ignition Is “On”:
• Depress the “LOCK” button.
• The LED and parking lights will flash [2] times. The siren/horn will chirp [2] times.
To Prevent Remote Panic Activation At All Times:
• Depress the “LOCK” button.
• The LED and parking lights will flash [3] times. The siren/horn will chirp [3] times.
To Allow Remote Panic Activation At All Times: [Factory Default Setting]
Allows panic activation regardless if Ignition is “ON” or “OFF”:
• Depress the “LOCK” button.
• The LED and parking lights will flash [1] time. The siren/horn will chirp [1] time.
Door Unlock Pulses [Factory Default Setting Is Singe Pulse]
Some vehicles require [2] unlock pulses for the doors to unlock by remote control.
To Program the Module for [2] Unlock Output Pulses:
• Depress the “UNLOCK” button.
• The LED and parking lights will flash [2] times. The siren/horn will chirp [2] times.
To Program the Module Back To [1] Unlock Output Pulse: [Factory Default 1]
• Depress the “UNLOCK” button.
• The LED and parking lights will flash [1] time. The siren/horn will chirp [1] time.
Interior Light Activation Upon Disarm [Factory Default Setting Is “ON”]
The interior light activation feature upon disarm can be programmed “OFF” or back “ON”.
To Program the Interior Lights Activation “OFF”:
• Depress both the “LOCK” and the “UNLOCK” buttons at the same time.
• The LED and parking lights will flash [2] times. The siren/horn will chirp [2] times.
To Program the Interior Light Activation Back “ON”: [Factory Default Setting]
• Depress both the “LOCK” and the “UNLOCK” buttons at the same time.
• The LED and parking lights will flash [1] time. The siren/horn will chirp [1] time.
Miscellaneous Feature Programming
11
START2 UM 3/5/02 2:31 PM Page 11
One (1) Year Limited Warranty
Magnadyne Corporation or its authorized agents will, within a period of one year from the date of
sale to you the original purchaser, repair, replace or refund the retail sales price of said product or
any part thereof, at the option of Magnadyne Corporation or its authorized agents, if said product or
part is found defective in materials or workmanship, when properly connected and operating on the
correct power requirements designated for the specific product. This warranty and Magnadyne
Corporation or its authorized agents obligations, hereunder does not apply where the product was:
damaged while in the possession of the consumer, subjected to unreasonable or unintended use,
not reasonably maintained, utilized in commercial or industrial operation, or serviced by anyone
other than Magnadyne Corporation or its authorized agents, or where the warning seal on the
product is broken or the power plugs or wires are detached from the unit. Magnadyne Corporation
or any of its authorized agents do not assume any labor cost for the removal and reinstallation of
any product found to be defective, or the cost of transportation to Magnadyne Corporation or its
authorized agents. Such costs are the sole responsibility of the purchaser.
This warranty does not cover the cabinet, appearance items, normal wear and tear or accessories
used in connection with the products resulting from improper installation, alteration, accident,
misuse, abuse or acts of nature.
Magnadyne Corporation or its authorized agents shall not be liable to anyone for consequential
or incidental damages or claims that may arise due to failure of product to operate properly
except those accorded by law. Magnadyne's or its authorized agents liability is strictly limited to
the repair, replacement of the product as stated above if all conditions of the warranty are met.
No expressed warranty or implied warranty is given except those set forth herein. Magnadyne
does not warranty or guarantee against break in damage or the theft of the vehicle in part or
whole, or against the loss or damage to the contents of any vehicle in which a security system is
installed. Magnadyne security systems are only a deterrent against possible theft.
This warranty extends only to the original purchaser of the product and for the vehicle in which it
was originally installed. This warranty is not transferable or assignable to any other person or
vehicle.
Defective merchandise should be returned to the original point of purchase or secondly to
Magnadyne Corporation, 1111 W. Victoria Street, Compton, CA 90220. A return authorization must
be obtained before sending, or merchandise may be refused.
START2UM Rev A
© 2002 Copyright Magnadyne Corp. 3-5-02
Warranty
START2 UM 3/5/02 2:31 PM Page 12
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12

Carbine Carbine PL80 Owner's manual

Carbine PL80
Brand
Carbine
Model
Carbine PL80
Category
Remote starters
Type
Owner's manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents