ASTDVD1938W HDID
Quick Start Guide
GETTING STARTED
1.
Please read the safety section (page 2) in the main instructions
before proceeding further. This section
contains vital information to ensure safe positioning and use of
the TV
2.
Unpack the TV and place on a flat level surface suitable to support the weight of the TV (5.0 kg approx.).
3.
Remove the plastic protective film on the front of the screen.
4.
Connect the aerial into the RF socket at the left side of the TV
(Fig 2).
Fig.1 Fig.2
Fig.3
5.
Connect the mains power lead to the mains adaptor and insert the
DC jack into
the DC-IN socket at the left side of the TV. Plug in and switch on at the mains.
The LED indicator on the TV will illuminate and show red (Fig 1).
6.
Open the battery compartment cover (Fig 3) on the reverse of the
remote
control. Insert 2 x AAA 1.5V alkaline batteries in accordance with the diagram in
the battery compartment. Take care to observe the correct polarity (+/-). Refit
the battery compartment cover
7.
Press the POWER button (Fig 4) to turn the TV set on. The LED indicator will
turn green and after a few seconds, the screen will activate and
the first time
installation menu (Fig. 5) will appear.
8.
Use the cursor ▼/▲ buttons on the remote control to move up and down the
display to highlight desired options.
9.
Use the ► button to select (√
) or deselect the options.
10.
If ANALOGUE PROGRAM SEARCH and DIGITAL PROGRAM SEARCH are
selected, use the cursor ▼ button to highlight OK and press ENTER. The TV
will initially search for the analogue stations (Fig 6) followed
by the digital
stations. On completion of the search the TV will default to Channel 1 on the
digital service.
11.
If the picture quality is poor or only a limited number of digital channels are
stored it is possible that the aerial may need to be upgraded for the digital TV
function to work in your area.
WATCHING TV (basic operation)
12.
To select a channel either enter the number of the channel using
the number
buttons on the remote control or scroll through the channels using the cursor ▲ /
▼ buttons or channel CH+/-
buttons.
13.
To view analogue TV channels press the INPUT button to display the source
menu (Fig 7). Using the cursor ▲ / ▼ buttons highlight TV on the menu and
press ENTER to select. To view digital TV channels select DTV on this same
menu.
14.
To check the list of channels stored, press the ENTER button to display the
channel list and use the cursor ▲ / ▼ buttons to move up and down the display.
To select a channel, highlight the channel on the list and press
ENTER to
confirm.
15.
Adjust the volume to the desired level using the volume or cursor ◄ / ►buttons.
The sound can be silenced by pressing the MUTE button on the remote control
and a mute symbol will appear on the screen. Press the MUTE button a second
time to restore the sound.
16.
To switch off the TV for short periods, press the POWER button. The TV will go
into standby mode and the LED indicator will change to red. If not using the TV
for extended periods turn off at the mains switch to conserve electricity, all
settings will be retained.
Fig.4
Fig.5
Fig.6
Fig.7
DVD Operation
17 To select DVD operation press the INPUT button to display the source menu (Fig 7). Using the cursor ▲ / ▼ buttons
highlight DVD on the menu and press ENTER to select.
18 Place a DVD or CD-R disc into the slot on the right side of the Tv. (Fig 8). The disc must have the mirrored surface
facing you and the label side facing away. Do not handle the disc surface . Push the disc in gently and it will load
automatically.
Mirror Side
Fig.8
19 The disc will now start to be “Read”
and then, depending upon the type of disc, will play or display
the disc menu or
disc contents. Select the item you wish to view, using the navigation buttons on the remote control and press
“ENTER”.
20.
To manually control DVD play you can use the control buttons located on the side panel (Fig 9).
Fig.9
For advanced operation of this TV and DVD player please consult the Instruction Manual.
Should you have difficulty in operating this unit, please consult the Trouble Shooting Guide
in the Instruction Manual. If you suspect a fault, please contact the Customer Help
Line, details of which can be found in the Instruction Manual.
21. When you wish to remove a disc, press STOP and then EJECT. Do not grip the disc to pull it out of the player, wait
until the disc stops moving before gripping the disc outer and removing carefully. See page 35 in the main manual
for correct handling of discs
/