AG Neovo TX-22 User manual

TX-22 White LCD Monitor

User Manualdisplays.agneovo.com

The information contained in this document is subject to change without notice.

This document contains proprietary information that is protected by copyright. All rights are reserved. No

part of this document may be reproduced,translated to another language or stored in a retrieval system,

or transmitted by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior

written permission. Windows is a registered trademark of Microsoft, Inc. Other brand or product names

are trademarks of their respective holders.

The test results show that this device meets the FCC rules. Those limits are set to protect residential

areas from the devices with harmful emission. This device will produce, use and radiate radio

frequency energy. In addition, failure to follow the user’s manual to install or use this device might

produce harmful interference with radio communication. Not withstanding the foregoing, it does not

guarantee that this type of harmful interference does not occur in some special installations. The

interference caused by this device to the reception of radio or television signals may be veried by

turning it on and o. Any changes or modications to this TFT LCD would void the user’s authority to

operate this device.

CLASSIFICATION .................................................................................................................1

INTENDED USE ....................................................................................................................2

FOLLOW THE NATIONAL REQUIREMENT TO DISPOSE UNIT ........................................3

ELECTROMAGNETIC COMPATIBILITY .............................................................................. 4

USAGE NOTICE ...................................................................................................................8

Chapter 1: Product Description

1.1 Package Overview ............................................................................................................................. 10

Chapter 2: Installation

2.1 Product Overview ............................................................................................................................... 11

2.1.1 Front View ............................................................................................................................... 11

2.1.2 Bottom View (Without Stand) .................................................................................................. 11

2.2 VESA Mount for Your Monitor ............................................................................................................. 12

2.3 Start Your Installation ......................................................................................................................... 13

2.4 Connecting the Display ...................................................................................................................... 14

2.5 Disconnecting the Device ................................................................................................................... 14

Chapter 3: User Controls

3.1 Side Panel Controls ............................................................................................................................ 15

3.2 How to Use the OSD Menus .............................................................................................................. 16

3.3 On-Screen Display Menus ................................................................................................................. 17

Chapter 4: Appendix

4.1 Troubleshooting .................................................................................................................................. 18

4.2 Warning Signal ................................................................................................................................... 19

4.2.1 No Signal ................................................................................................................................. 19

4.2.2 Going to Sleep......................................................................................................................... 19

4.2.3 Out of Range ........................................................................................................................... 19

4.3 Product Dimensions ........................................................................................................................... 20

4.4 Compatibility Modes ........................................................................................................................... 21

4.5 Touch Screen Driver Installation ......................................................................................................... 22

4.5.1 TX-22 White Driver Install Instructions ....................................................................................... 22

Chapter 5: Specications

5.1 Display Specications ........................................................................................................................ 24

TABLE OF CONTENTS

˙

Power by Class I power supply

( Adapter Technology Co., Ltd./ATM065-P120)

˙

No Applied Part

˙

Mode of operation: Continuous Operation

˙

The equipment not suitable for use in the presence of a ammable

anesthetic mixture with air or with oxygen or nitrous oxide: Not AP Category.

CLASSIFICATION

The intended use of the TX-22 White is to serve as a LCD monitor for

integration with the hospital system. It is designed for general purpose for

hospital environment. For displaying and viewing of images for reference. The

use of this device does not require any direct contact with patients. It shall not

be used for diagnostic purpose and cannot be used for a life-support system.

Equipment connected to the analogue or digital interface must comply with

the respective IEC standards (e.g. IEC 60950 for data processing equipment

and IEC 60601-1 for medical equipment). Furthermore all congurations shall

comply with the current version of the standard for SYSTEMS IEC 60601-

1-1. Everybody who connects additional equipment to the signal input part

configure a medical system, and is therefore responsible that the system

complies with current version of the requirements of the system standard IEC

60601-1. If in doubt, consult the technical service department or your local

representative.

The instructions for use shall document:

The use of the ME EQUIPMENT as intended by the MANUFACTURER;

The frequently used functions;

˙

Any known contraindication(s) to the use of the ME EQUIPMENT; and

those parts of the ME EQUIPMENT that shall not be serviced or

maintained while in use with a PATIENT.

INTENDED USE

FOLLOW THE NATIONAL REQUIREMENT TO DISPOSE UNIT

Manufacturer's Recycling and Energy Information

Disposing of your old product

˙

Within the European Union

EU-wide legislation, as aimplemented in each Member State,

requires that waste electrical and electronic products carrying the

mark (left) must be disposed of separately from normal household

waste. This includes monitors and electrical accessories, such

as signal cables or power cords. When you need to dispose of your display

products, please follow the guidance of your local authority, or ask the shop

where you purchased the product, or if applicable, follow any aggreements

made between yourself.

The mark on electronical and electronic products only applies to the current

European Union Member State.

˙

Outside the European Union

If you wish to dispose of used electrical and electronic products outside

the European Union, please contact your local authority so as to comply

with the correct disposal method.

ELECTROMAGNETIC COMPATIBILITY

This symbol alerts the user that important literature concerning the operation and maintenance of this unit

has been included. Therefore, it should be read carefully in order to avoid any problems.

Stand by

Indicates Direct Current (DC)

Indicates Alternating Current (AC)

Indicates this device must not be thrown in the trash but must be recycled, according to the European WEEE

(Waste Electrical and Electronic Equipment) directive

Indicates compliance with the Directive 93/42/EEC as Class I device

Atmospheric pressure: 500hPa~1,060hPa

Humidity: 10~90% RH

Storage temperature: -20 degree to 60 degree

Recyclable

1060 hPa

500 hPa

90 %

10 %

-20 °C

+60 °C

ELECTROMAGNETIC COMPATIBILITY

Guidance and Manufacturer's Declaration - Electromagnetic Emission

The Model TX-22 White is intended for use in the electromagnetic environment specied below.

The user of TX-22 White should assure that it is used in such an environment.

Emission test Compliance Electromagnetic Environment - Guidance

RF emissions CISPR 11 Group 1

The Model TX-22 White uses RF energy only for its internal function.

Therefore, its RF emissions are very low and are not likely to cause any

interference in nearby electronic equipment

RF emissions CISPR 11 Class B

TX-22 White is suitable for use in all establishments, including domestic

establishments and those directly connected to the public low-voltage power

supply network that supplies buildings used for domestic purposes

Harmonic emissions

IEC61000-3-2

Class D

Voltage Fluctuations

IEC61000-3-3

Complies

Manufacturer's Declaration - Electromagnetic Immunity

The Model TX-22 White is intended for use in the electromagnetic environment specied below.

The user of TX-22 White should assure that it is used in such an environment.

Immunity Test IEC 60601 Test Level Compliance Level

Electromagnetic Environment -

Guidance

Electrostatic discharge

(ESD)

IEC61000-4-2

±6 kV contact

±8 kV air

±6 kV contact

±8 kV air

Floors should be wood, concrete or

ceramic tile. If oors are covered with

synthetic material, the relativehumidity

should be at least 30%.

Electrical fast transient

/burst IEC61000-4-4

±2 kV for power supply lines

±1 kV for input / output lines

±2 kV for power supply lines

±1 kV for input / output lines

Mains power quality should be that of a

typical commercial or hospital

environment

Surge

IEC61000-4-5

±1 kV dierential mode

±2 kV common mode

±1 kV dierential mode

±2 kV common mode

Mains power quality should be that

of a typical commercial or hospital

environment.

Power frequency

(50/60Hz)

mag-netic eld

IEC 61000-4-8

3.0 A/m 3.0 A/m

Power frequency magnetic elds

should be at levels characteristic of a

typical location in a typical commercial

orhospital environment.

Voltage dips, short

interruptions andvoltage

variations onpower

supply inputlines

IEC61000-4-11

<5% Ut (>95% dip in Ut)for

0.5 cycle

40% Ut (60% dip in Ut)for

5 cycles

70% Ut (30% dip in Ut)for

25 cycles

<5% Ut (>95% dip in Ut)for

5 sec.

<5% Ut (>95% dip in Ut)for

0.5 cycle

40% Ut (60% dip in Ut)for 5

cycles

70% Ut (30% dip in Ut)for

25 cycles

<5% Ut (>95% dip in Ut)for

5 sec.

Mains power quailityshould be

that of a typicalcommercial or

hospitalenvironment. If the user of

the TX-22 White image intensier

requirescontinued operation during

power mains interruptions, it is

commended that the TX-22 White

image intensier bepowered from

an uninterruptible power supply or a

battery.

Note: Ut is the A.C. mains voltage prior to application of the test level.

Manufacturer's Declaration - Electromagnetic Immunit

The Model TX-22 White is intended for use in the electromagnetic environment specied below.

The customer or the user of TX-22 White should ensure that it is used in such an environment.

Immunity Test IEC 60601 Test Level Compliance Level Electromagnetic Environment - Guidance

Conducted RF

IEC61000-4-6

Radiated RF

IEC 61000-4-3

3 Vrms

150 KHz to 80 MHz

3 Vrms

800 MHz to 2.5 GHz

3 Vrms

150 KHz to 80 MHz

3 Vrms

800 MHz to 2.5 GHz

Portable and mobile RF communications

equipment should be used no closer toany part

of the TX-22 White, includingcables, than the

recommended separationdistance calculated from the

equationapplicable to the frequency of thetransmitter.

Recommended Separation Distance0.15 MHz to 80

MHz

80 MHz to 800 MHz

800 Mhz to 2.5GHz

where P is the maximum output power rating of the

transmitter in watts (W)according to the transmitter

manufacturer and is the recommended separation

distance in meters (m). Field strengths from xed RF

transmitters,as determined by an electromagneticsite

survey (a), should be less than the compliance level in

each frequency range(b).Interferency may occur in the

vicinity of equipment marked with the following symbol:

NOTE 1: At 80MHz and 800MHz, the higher frequency range applies.

NOTE 2: These guidelines may not apply in all situations. Electromagnetic propagation is aected by absorption and

reection from structures, objects, and people.

(a) Field strengths from xed transmitters, such as base stations for radio (cellular/cordless) telephones and land mobile

radios, amateur radio, AM and FM radio broadcast and TV broadcast, connot be predicted theoretically with accuracy.

To assess the electromagnetic environment due to xed RF transmitters, an electromagnetic site survey should be

considered. If the measured eld strength in the location in which the TX-22 White is used exceeds the applicable RF

compliance level above, the TX-22 White should be observed to verify normal operation. If abnormal performance is

observed, additional measures may be necessary, such as reorienting or relocating the TX-22 White.

(b) Over the frequency range 150kHz to 80MHz, eld strengths should be less than [V1] V/m.

ELECTROMAGNETIC COMPATIBILITY

Recommended Separation Distances Between Portable and Mobile RF Communications

Equipement and the TX-22 White

The TX-22 White is intended for use in an electromagnetic environment in which radiated RF

disturbances are controlled. The user of the TX-22 White can help prevent electromagnetic

interference by maintaining a minimum distance between portable and mobile RF communications

equipment (transmitters) and the TX-22 White as recommended below, according to the maximum

output power of the communications equipment.

Rated maximum output

power (W) of transmitter

Separation distance (m) according to frequency of transmitter

150kHz to 80MHz

d=1.17,

80MHz to 800MHz

d=1.17,

800MHz to 2.5GHz

d=2.33,

0.01 0.12 0.12 0.23

0.1 0.38 0.38 0.73

1 1.2 1.2 2.3

10 3.8 3.8 7.3

100 12 12 23

For transmitters rated at a maximum output power not listed above, the recommended separation distance (d) in meters (m)

can be estimated using the equation applicable to the frequency of the transmitter, where P is the maximum output power

rating of the transmitter in watts (W) according to the transmitter manufacturer.

NOTE 1: At 80 MHz and 800 MHz, the separation distance for the higher frequency range applies.

NOTE 2: These guidelines may not apply in all situations. Electromagnetic propagation is aected by absorption and

reection from structures, objects, and people.

ELECTROMAGNETIC COMPATIBILITY

Precautions

Follow all warnings, precautions and maintenance as recommended in this user’s manual to

maximize the life of your unit.

Do:

• Turn o the product before cleaning.

• Touch screen surface may be cleaned using a soft clean cloth moistened with water.

• Use only high quality and safety approved AC/DC adapter.

• Disconnect the power plug from AC outlet if the product is not going to be used for an extended

period of time.

Don’t:

• Do not touch the LCD display screen surface with sharp or hard objects.

• Do not use abrasive cleaners, waxes or solvents for your cleaning.

• Do not operate the product under the following conditions:

- Extremely hot, cold or humid environment.

- Areas susceptible to excessive dust and dirt.

- Near any appliance generating a strong magnetic eld.

- In direct sunlight.

Turning o TX-22 White properly is important for system reliability. There are one way to turn o the

system. Push the power button and then the system will shut down automatically.

Caution - To prevent the risk of re or shock hazards, do not expose this

product to rain or moisture.

Warning - Please do not open or disassemble the product as this may cause

electric shock.

USAGE NOTICE

Please do not touch patient and this medical device at the same time.

Users must not allow SIP/SOPs and the patient to come into contact at the same time.

CAUTION – Use suitable mounting apparatus to avoid risk of injury.

Grounding reliability can only be achieved when the equipment is connected to an equivalent

receptacle marked “Hospital Only” or “Hospital Grade”.

Use a power cord that matches the voltage of the power outlet, which has been approved and

complies with the safety standard of your particular country.

Warning - Do not modify this equipment without authorization of the manufacturer.

Warning – To avoid risk of electric shock, this equipment must only be connected to a supply

mains with protective earth.

Caution: This adapter (Adapter Technology Co., Ltd./ATM065-P120)

is a forming part of the medical

device.

USAGE NOTICE

CHAPTER 1: PRODUCT DESCRIPTION

1.1 Package Overview

LCD Display

Power Cord

VGA Signal Cable

USB Cable ( A to B)

DVI-D Cable

DC Power Supply

Cable Cover Screw

(M3x6mm)

TX-15, TX-17, TX-19, TX-22 & TX-22 White

displays.agneovo.com

TX22C0/TX19B0/TX17B0/TX15B0_Quick Guide_V010

Quick Start Guide

TX-15, TX-17, TX-19, TX-22 & TX-22 White Multi-touch Display

Quick Start Guide

CHAPTER 2: INSTALLATION

2.1 Product Overview

2.1.1 Front View

2.1.2 Bottom View (Without Stand)

VGA

USB

DC IN

DVI

RJ-11

Power indicator Indicate the operating status of the LCD display:

- Lights Green when the LCD display is turned on.

- Lights orange when the LCD display is in standby mode.

- Lights off when the LCD display is turned off.

INSTALLATION

2.2 VESA Mount for Your Monitor

This monitor conforms to the VESA Flat Panel Mounting Physical Mounting Interface standard which

denes a physical mounting interface for at panel monitors, and corresponding with the standards

of at panel monitor mounting devices, such as wall and table arms. The VESA mounting interface

is located on the back of your monitor.

To mount the monitor on a UL certied swing arm or other mounting xture, follow the instructions

included with the mounting xture to be used.

Warning!

Please select the proper screws!

The distance between the back cover surface and the bottom of the screw hole is

8 mm. Please use four M4 screws diameter with proper length to mount your monitor.

Please note: the mounting stand must be able to support at least 17.6 lbs (8Kg).

100.0 mm

VESA

Mounting

Interface

100.0 mm

VESA mounting

INSTALLATION

2.3 Start Your Installation

Please follow these instructions so that you can hook up the cables to associated connectors.

1. Lay the LCD at on an even surface.

2. Move the stand into position as seen in the step 1 diagram.

3. Remove the cable cover as seen in the step 2 diagram.

4. Connect the cables to the appropriate connectors as seen in the step 3 diagram.

5. Re-attach the cable cover. Take the screw (M3x6mm) out of the accessory box, and insert the

screw into the cable cover and monitor as seen in the step 4 diagram.

* Screw the cable cover to the monitor in normal use.

Step 3

VGA

USB DVI

DC IN

Step 2Step 1

Step 2

Step 2Step 4

INSTALLATION

2.4 Connecting the Display

To setup this display, please refer to the following gure and procedures.

1. Be sure all equipment is turned o.

2. Connect the DC plug to the power connector on the monitor and the other end into an

electrical outlet.

3. Connect the D-SUB or DVI cable from the display’s D-SUB or DVI input connector to the

D-SUB or DVI connector of your host computer and tighten the screws.

4. Connect the USB cable from the USB port of your display to the USB port of your computer.

5. Congure the touch screen. Refer to the “4.5 Touch Screen Driver Installation” section on

page 19.

6. Once the touch screen is congured, the monitor is ready for use.

7. The function of RJ-11 port is used only for Remote Key pad(Sold Separately).

Don’t connect telephone or internet cable to RJ-Type port.

2.5 Disconnect Device

Caution:

To prevent the risk of electric shock, make sure power cord is unplugged from wall socket. To

fully disengage the power to the unit, please disconnect the power cord from the AC outlet. Do

not remove cover (or back). No user serviceable parts inside. Refer servicing to qualied service

personnel. The AC outlet shall be readity available and accessible.

Notice!

To ensure the LCD display works well with your computer, please congure the display mode

of your graphics card to make it less than or equal to 1920 x 1080 resolution and make sure

the timing of the display mode is compatible with the LCD display.

We have listed the compatible “Video Modes” of your LCD display in the appendix (on page

18) for your reference.

External power supplies applicable:

Adapter Technology Co., Ltd./100-240V, 50 - 60Hz, 1.6-0.7A/ATM065-P120.

CHAPTER 3: USER CONTROLS

3.1 Side Panel Controls

Icon Key Name

Down

Select

Power

OSD

Key

Menu o status Menu on status

Menu appear Menu disappear / return to main item

Brightness Main item select up / Adjust up

Contrast Main item select down / Adjust down

Select sub-item function

Power On / O

USER CONTROLS

3.2 How to Use the OSD Menus

Icon Key Name

Down

Select

Power

1. Press the “Menu” button to pop up the “on-screen menu” and press “Up” or “Down” button to

select among the ve functions in the main menu.

2. Choose the adjustment items by pressing the “Select” button.

3. Adjust the value of the adjustment items by pressing the “Up” or “Down” button.

4. With the OSD menu on the screen, press the “Menu” button to return to the main menu or to exit

OSD.

5. The OSD menu will automatically close, if you have left it idle for a pre-set time.

6. To Lock the OSD / Power menu buttons, please follow the instructions below.

(Please note: the monitor has to be turned ON with a valid signal pre-set)

(a.) Press the “Menu” key; the OSD menu will open.

(b.) Press and hold the “Menu” key again with the OSD menu on the screen; the OSD menu will

disappear. Then press the “Power” key 1 time while the menu key is still being pressed. The

“Lock/Unlock” menu will appear for 3 seconds.

(c.) Use the “Select” key to select OSD or Power setting then set at “Lock” by pushing the “UP” or

“Down” button.

(d.) When the “UP” or “Down” button is released, the previous setting will be saved and exit the

“Lock/Unlock” menu automatically.

7. To Unlock the OSD / Power menu buttons, please follow the instructions below.

(Please note: the monitor has to be turned ON with a valid signal pre-set)

(a.) Press and hold the “Menu” key then press the “Power” key simultaneously; the “Lock/Unlock”

menu will appear for 3 seconds.

(b.) Use the “Select” key to select OSD or Power setting then set at “Unlock” by pushing the “UP”

or “Down” button.

(c.) When the “Up” or “Down” button is released, the previous setting will be saved, and the “Lock/

Unlock” menu will close automatically.

Please note:

a. When the OSD Lock function is selected, this indicates that all the buttons except the “power”

button are now disabled.

b. When the Power Lock function is selected, the “Power” key is disabled. The user cannot turn

o the monitor with the “Power” key.

USER CONTROLS

3.3 On-Screen Display Menus

Main OSD Menu:

ITEM CONTENT

Contrast The monitor luminance level control.

Brightness The monitor backlight level control.

Auto Adjust Fine-tune the image to full screen automatically.

Left/Right Moving screen image horizontal position to left or right.

Up/Down Moving screen image vertical position to up or down.

Horizontal size The screen image horizontal dot clock adjustment.

Fine The screen image pixel phase adjustment.

OSD Left/Right Moving OSD menu horizontal position to left or right.

OSD Up/Down Moving OSD menu vertical position to up or down.

OSD Time out OSD auto-disappear time selection.

OSD Language

OSD menu language selection. ( English, French, Japanese, Deutsch,

Spanish, Italian, Traditional Chinese and Simplied Chinese)

Factory Reset Factory default value restored.

RGB Color temperature selection. (9300K, 6500K, 5500K, 7500K, User)

Indicator lights and push-buttons

Color Meaning

Green Ready for use

Orange Stand by

AG Neovo TX-22 User manual

Related papers

Other documents