2. Linshang
  3. LS220B
LS220B

Linshang LS220B User manual

  • Hello! I've reviewed the user manual for the Linshang LS220B Coating Thickness Gauge. This device is used for measuring car paint thickness, featuring Bluetooth connectivity to a mobile app for data recording and report generation. It has a wear-resistant ruby probe and the ability to identify different substrates. I'm ready to answer any questions you may have about its operation and features.
  • What type of coatings can the gauge measure?
    Does the device require calibration?
    Can the gauge connect to a mobile app?
Shenzhen Linshang Technology Co., Ltd.
3/12/2022 Page 1 of 13
LS220B
Coating Thickness Gauge
User Manual V2.01
Scan the QR code download and install the App
Please read this manual carefully before using and reserve it for reference.
Shenzhen Linshang Technology Co., Ltd.
3/12/2022 Page 2 of 13
I. Product introduction
The coating thickness gauge is used for measuring the thickness of automobile paint. The gauge transmits
the measurement data to the mobile phone APP in time through Bluetooth. The mobile APP can record
the paint thickness of different parts of the car and the corresponding shell material and can generate test
reports. Test reports can be stored in image format and can be shared via QQ and We Chat.
Standards for the product:
GB/T 4956-2003 Non-magnetic Coatings on Magnetic Substrates-Measurement of Coating
Thickness-Magnetic Method
GB/T 4957-2003 Non-conductive Coatings on Non-magnetic Basis Metals-Measurement of Coating
Thickness-Eddy Current
DIN EN ISO 2808 Paints and Varnishes-Determination of Film Thickness
JJG-818-2005 Verification Regulation of Magnetic and Eddy Current Measuring Instrument for
Coating Thickness
II. Technical parameters
Probe tip
Ruby
Measuring principle
Fe: Hall Effect / NFe: Eddy current
Probe type
Built-in integrated probe
Measuring range
0.0-2000μm
Resolution
0.1μm:（0μm - 99.9μm）
1μm:(100μm - 999μm)
0.01mm:(1.00mm - 2.00mm)
Accuracy
≤±(3%H+2μm), H is the standard value
Unit
μm / mil
Measuring interval
0.5s
Minimum measuring area
Ø = 25mm
Minimum curvature
Convex:5mm / Concave:25mm
Minimum substrate thickness
Fe:0.2mm / NFe:0.05mm
Display
128×48 dot matrix LCD
Shenzhen Linshang Technology Co., Ltd.
3/12/2022 Page 3 of 13
Power supply
2pcs of 1.5V AAA alkaline battery
Operation temperature range
-20℃-50℃
Storage temperature range
-20℃-60℃
Gauge size
101*62*28 mm
Weight(with battery)
79 g
Data transmission
Bluetooth
III. Product advantages
1. No calibration, just zero adjustment.
2. One hand operation, only one button.
3. Fast measurement, 0.5s measuring interval.
4. Wear-proof ruby probe tip for long-term use.
5. The device can identify the ferrous putty as well as the galvanized iron substrate.
6. The gauge automatically identify the substrate and switch measurement mode rapidly.
7. "Fe", "NFe", "Fe/NFe" three measurement modes can be set.
8. Measuring non-magnetic coatings on steel or iron and measure Non-conductive coatings on non-
magnetic metal substrates in one gauge.
9. Thanks to the use of the most-advanced digital probe technology, these sensors are unsusceptible
to interference and provide an excellent measuring accuracy. Even variations in temperature will not
affect measurement and readings remain stable to ensure a very good reproducibility over the
complete measuring range.
10. Built-in Bluetooth function, it can connect to the mobile APP and realize the whole automobile
measurement data recording and generate the test report.
IV. Operation
1. Power on/off
Power on:
Short press the button to turn on the gauge. Version number and serial number will be displayed and the
gauge enter the last recorded historical data interface.
Power off:
Shenzhen Linshang Technology Co., Ltd.
3/12/2022 Page 4 of 13
Long press the button to shut down the gauge, or the gauge will automatically shut down in 3 minutes
without any operation. When Bluetooth is connected, the gauge will automatically shut down in 10 minutes
without any operation.
2. Device setting
In the off state, long press the button for 3 s to enter the setting interface. After entering the setting interface,
if there is no operation for more than 20 s, the instrument will automatically shut down. Short press the
button can select the settings; Long press the button for 3 s and less than 5 s to confirm the settings; long
press the button for 5 s, the instrument exits the setting and shuts down and the setting is invalid.
Language settings
The instrument is available in Chinese, English, Russian, Turkish.
Setting method: In the main setting interface, short press power button to select "Language" option, long
press the button for 3 seconds to confirm the selection, short press the button again to select the desired
language, long press the button for 3 seconds to confirm the selection, and return to the main setting
interface.
Setting interface Language selection
Measurement modes selection
There are three measurement modes: Ferrous substrate measurement (Fe), Aluminum substrate
measurement (Al), and Auto identification (Fe/Al). Under normal circumstances, it is enough to use Fe/Al
auto identification mode. This mode features identification of the ferrous putty and galvanized iron
substrate. When the measurement substrate is settled, you can select Fe or Al as the fixed
measurement mode.
Setting method: In the main setting interface, select "mode" option by short pressing power button, and
long press the button for 3 seconds to confirm the selection. Shortly press the button to select the
measurement mode. And long press the button for 3s to confirm the selection and back to the main
setting interface.
Shenzhen Linshang Technology Co., Ltd.
3/12/2022 Page 5 of 13
Unit setting
The device can be set to the metric or imperial unit, and the factory default is metric.
Setting method: In the main setting interface, shortly press the button to select “Unit”. Long press the
button for 3s to confirm and then enter the unit selection interface. Shortly press the button to select your
unit and long press the button for 3s to confirm and back to the main setting interface.
Main setting interface Unit selection interface
Exit
In the main setting interface, short press power button to select "Exit", long press the button for 3
seconds to confirm and enter the measurement interface
3. Zero adjustment
A zero-adjustment is required when using the gauge for the first time, after inserting new batteries, working
with different materials or ambient temperature changes. Using iron-base and aluminum - base adjustment
plates respectively to carry out zero adjustment. We strictly recommend carrying out the reference check
on the uncoated original substrate, due to the difference of magnetic and conductive properties of the
material, some measurement deviation will be caused. If this is not possible, please use the zero reference
plates supplied with in the case, there are Fe plate and NFe plate, please choose correctly according to
the measuring materials.
3.1 Measuring the plate or uncoated original substrate, a measured value will be displayed on the gauge,
please make sure the probe tip is placed perpendicularly and evenly on the surface.
3.2 Hold the probe still, long press the button for 3s, the gauge will display “zero reference place probe”
(as shown in below picture).
Shenzhen Linshang Technology Co., Ltd.
3/12/2022 Page 6 of 13
3.3 After hearing a buzzer sound, the gauge will display “Lift off probe at least 15 cm” (as shown in below
picture), release the button and lift the probe away from the plate (substrate) for at least 15 cm.
3.4 The zero adjustment completed when there is the buzzer sound again, and the LCD screen displays
0.0.
3.5 After the zero adjustment is completed, place the standard film on the plate (substrate), if the
measurement value is stable and deviation from standard value within ±3μm, the gauge can be used
normally.
Note: After the zero adjustment completed，when repeating measurement on the same spot, the reading
may not always be 0μm, since surface roughness, dirt, scratches etc. might cause variances. The
operation of the gauge should be correct and proficient; otherwise, it will lead to instability of the
measured values.
4. Measurement
1) Use fingers to hold gauge where there is non-slip groove.
2) Press the gauge vertically on the surface of the object to be measured. Keep the gauge steady and
do not tilt or shake it. The result will be shown on the screen, and there will be a buzzer.
3) To continue measuring, lift the gauge away from the object. Repeat the operation of step 2).
4) When the device identifies the ferrous putty, the buzzer alerts for two times. And the interface of the
device will prompt: “Ferrous putty”. When the device identifies the galvanized iron, it will turn on the
green backlight. The substrate is displayed as “FeZn”.
Shenzhen Linshang Technology Co., Ltd.
3/12/2022 Page 7 of 13
5. Check measurement records
In measurement mode, short press the button to check historical data. The gauge stores 9 sets of data.
When more than 9 sets of data are stored, the earliest recorded value is automatically deleted and No.1
is the last test data. Recorded data won’t loss after powering off.
V. Bluetooth communication
The coating thickness gauge is equipped with built-in Bluetooth communication, which can be connected
to the gauge through the mobile app.
5.1 Mobile APP Installation Requirements and Methods
The mobile APP supports Android OS 6.0 and above. Use the mobile browser scan the QR code download
and install the Coating Thickness Gauge. apk software.
After the installation is complete, the “漆膜仪(Coating thickness gauge)” icon will appear as shown below.
5.2 How to connect the Bluetooth device
A. Open the APP and display the “Linshang” logo for 3 seconds. If there is no bound Bluetooth device,
then enter the Bluetooth setting interface.
Click "开始搜索(Start Search)", prompt "正在搜索设备…(Searching for device...)" and list the available
Bluetooth devices that are searched; click the "停止搜索(Stop Search)" button to stop searching for
Bluetooth devices and the search indicator icon disappears. Selecting "LS" + gauge serial number will
bind the selected gauge (prompt: each gauge has a unique serial number).
Shenzhen Linshang Technology Co., Ltd.
3/12/2022 Page 8 of 13
After the connection is successful, it will automatically enter into the main measurement interface and
display the information read by the gauge and Bluetooth icon will be displayed at the bottom right of
the gauge screen.
Shenzhen Linshang Technology Co., Ltd.
3/12/2022 Page 9 of 13
B. If the APP has a bound Bluetooth device, the logo interface will appear for 3 seconds then automatically
search and connect the bound Bluetooth device. When the connection is successful, it will automatically
enter the “测量(Measurement)” interface and display the information read by the gauge.
5.3 Start measuring
Select the corresponding car position in the APP project bar to measure, the measurement data will be
uploaded to the selection bar and the latest measurement will be highlighted.
Shenzhen Linshang Technology Co., Ltd.
3/12/2022 Page 10 of 13
A. Each project bar can preserve the latest 8 sets of measurement data.
B. There are 17 projects totally for different parts of the car. (From top to bottom: car roof, engine
compartment cover, left front fender, left A-pillar, left front door, left B-pillar, left rear door, left C-pillar,
left rear fender, trunk lid, right rear fender, right C-pillar, right rear door, right B-pillar, right front door,
right A-pillar, right front fender).
C. The specific part name of the car that we test will be displayed at the upper left corner of each bar.
D. The “清空 (Empty)” button corresponding to each project bar can clear the measurement data of this
bar.
E. Select the “清空所有数据 (Clear All Data)” button in the upper left corner to clear all measurement data
and automatically return to the first bar to prepare for measurement.
5.4 Report Preview
Click on the "预览报告(Preview Report)" button at the top, the user can input information according to their
needs, or choose not to input any information.
Click "确定(Confirm)" to generate a report preview.
Shenzhen Linshang Technology Co., Ltd.
3/12/2022 Page 11 of 13
5.5 Report
Click the "报告(Report)" button and the APP will list all reports on the current phone.
Click "保存到相册(Save to Album)" to save the report to the phone album; The prompt will appear as below
when the save is successful.
Click “保存到相册(Save to Album)Save to Album” to save the report to the mobile phone album;
Click “分享(Share)” to share the report with your friends.
Shenzhen Linshang Technology Co., Ltd.
3/12/2022 Page 12 of 13
Click “删除(Delete)” to delete the current report.
Click “全选(Select All)” to delete the report in batches.
5.6 Exiting the APP
Click "退出(Exit)" in the lower right corner of the interface or click the phone to return. Pop up the
confirmation box, click “确定(Confirm)" to exit the software and disconnect the Bluetooth connection. If you
do not exit the application, the phone is always connected to the gauge in the background until the gauge
is turned off automatically without any operation in 10 minutes.
5.7 APP precautions
1) APP currently only supports Android, and IOS cannot be used.
2) Before using, please turn on the gauge before starting the app.
3) To exit the software, click the “退出(Exit)” button in the bottom menu or click phone to return. If you click
on the phone's menu button, the app will enter the background of the phone.
4) If there is a Bluetooth connection error or the data cannot be read, please try again as follows:
◎ Turn off the gauge and close the APP as in step 3).
◎ When the gauge is turned on, start the APP, enter the APP Bluetooth interface, click “开始搜索(Start
Search)” and select the device which is corresponding to the SN number in the “其他可用设备(Other
Available Devices)” column of the search result. If the connection is successful, the Bluetooth icon
will appear in the lower right corner of the gauge.
5) If the interface text is incomplete, please go to “Settings” / “Display and Brightness” / “Font Size” and
change the font size to make it smaller.
Shenzhen Linshang Technology Co., Ltd.
3/12/2022 Page 13 of 13
VI. Precaution
1. The device must be zero adjusted respectively with the iron-base and aluminum-base zero adjustment
plates. Otherwise, there may be abnormal identifications of the ferrous putty and galvanized iron
substrate.
2. Do not slide the probe on the surface of the car, which will result in damage to the paint and the gauge.
3. Please keep the car paint surface clean, the dust and dirt on the paint surface will affect the
measurement accuracy.
4. When the gauge displays low battery, the battery needs to be replaced.
VII. Packing list
No.
Description
Quantity
Unit
1
Coating Thickness Gauge
1
Set
2
Fe zero-adjustment plate
1
pcs
3
NFe zero-adjustment plate
1
pcs
4
Standard film
1
pcs
5
User manual
1
pcs
6
Drawstring bag
1
pcs
7
Certificate / Warranty card
1
pcs
8
1.5V AAA alkaline battery
2
pcs
VII. Service
1. The gauge has one-year warranty. If the gauge works abnormally, please send the whole gauge to our
company for maintenance.
2. Provide users with spare parts and lifelong maintenance services.
3. Provide the users with the gauge calibration service.
4. Free technical support for long term.
Manufacturer: Shenzhen Linshang Technology Co., Ltd.
Website: www.linshangtech.com
Service hotline: +86-755-86263411
Email: sales21@linshangtech.com
/