Surenoo SLC1602O Series User manual

www.surenoo.com

Page: 01 of 20

LCD MODULE USER MANUAL

Please click the following image to buy the sample

AIP31068

Reference Controller Datasheet

SLC1602O Series

Character LCD Selection Guide

Arduino Link

SHENZHEN SURENOO TECHNOLOGY CO.,LTD.

A3

Model No.: SLC1602O

www.surenoo.com

Shenzhen Surenoo Technology Co.,Ltd.

Skype: Surenoo365

CONTENTS

15B15B15B10HHHHHHHHHHHHHHHHHHHHHHH

18BHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH1. ORDERING INFORMATION - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 04U

19B19B19B14B14BHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH1.1 1602O Series Table- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 0HHHHHHHH4

20B20B20B15BHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH1.2 1602O Series Image- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 05H21BHHHHHHHHHHHH

21B18B18BHHHHHHHHHHHHHHHHHHHHUHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH2. SPECIFICATION - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 06U

22B19B19B14B14BHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH2.1 Display Specification- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 06

23B20B20B15BHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH2.2 Mechanical Specification - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 06

24B21BHHHHHHHHHHHH HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH 2.3 Electrical Specification - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 06

25B22B21BHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH2.4 Optical Specification - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 06

26B23B22B13BHHHHHHHHHHHHHHHHHHHHHHHHHHUHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH3. OUTLINE DRAWING- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 07U

21B18B18BHHHHHHHHHHHHHHHHHHHHUHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH4. ELECTRICAL SPEC - - -- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 08U

22B19B19B14B14BHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH4.1 Pin Configuration - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 08

23B20B20B15BHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH4.2 Absolute Maximum Ratings - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - HHHHHHHHHHHHHHHHHHHHHHHHH09

24B21BHHHHHHHHHHHH HHHHHHHHHHHHHHHHH HHHHHHHHHHHHHHHHHHHH4.3 Electrical Characteristics - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 09

HH31B28B26B29BHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH5. INSPECTION CRITERIA - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 10

32B29B27B30BHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH5.1 Acceptable Quality Level - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 1HHHH0

33B30B28B31BHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH5.2 Definition of Lot - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 1HHHH0

34B31B29B42BHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH5.3 Condition of Cosmetic Inspection - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 1HHHH0

35B32B30B43BHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH5.4 Module Cosmetic Criteria - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 11

36B33B31B44BHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH5.5 Screen Cosmetic Criteria (Non-Operating) - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 1HHHH3

37B34B32BHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH5.6 Screen Cosmetic Criteria (Operating) - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 1HHHHHH4

38B35B33B45BHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH 6. PRECAUTIONS FOR USING - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 16

39B36B34B31BHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH6.1 Handling Precautions - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 16

40B37B35B42BHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH6.2 Power Supply Precautions- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 17

41B38B36B43BHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH6.3 Operating Precautions - - - - - - - - - - - - - - - - - - -- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 17

42B39B37B44BHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH6.4 Mechanical/Environmental Precautions - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 17

43B40B38BHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH6.5 Storage Precautions - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 17

44B41B39BHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH6.6 Others - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 17

45B42B40BHHHHHHHH

www.surenoo.com

Page: 01 of 20

SHENZHEN SURENOO TECHNOLOGY CO.,LTD.

A3

Model No.: SLC1602O

7. HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHUSING LCD MODULES - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 18

46B43B41B31BHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH7.1 Liquid Crystal Display Modules - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 18

47B44B42B42BHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH7.2 Installing LCD Modules - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 1HHHHHH8

48B45B43B43BHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH7.3 Precaution for Handling Modules - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 19

49B46B44B44BHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH7.4 Electro-Static Discharge Control- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 19

50B47B45BHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH7.5 Precaution for Soldering to LCM- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 19

51B48B46BHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH7.6 Precaution for Operation - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2HHHH0

52B49B47BHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH7.7 Limited Warranty - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2HHHH0

53B50B48BHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH7.8 Return Policy - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 20

SUR

www.surenoo.com

Page: 02 of 20

SHENZHEN SURENOO TECHNOLOGY CO.,LTD.

A3

Model No.: SLC1602O

www.surenoo.com

Page: 03 of 20

1.ORDERINGINFORMATION

1.1 SLC1602O Series Table

Model No. Interface Display Outline Size

(MM)

Viewing Area

(MM)

Area Area

(MM)

Voltage

(V) Controller Mark Color Code IMAGE

More Color on Black

Black on More Color

AIP31068

3.3-5.0V56.20*11.5064.50*16.0080.00*36.00

16*02

I2C

SLC1602O

SHENZHEN SURENOO TECHNOLOGY CO.,LTD.

A3

Model No.: SLC1602O

C InterfaceII

www.surenoo.com

Page: 04 of 20

467B57B464B54B1.2 SLC1602O Series Image

*The number of series image is in accordance with number of the above series table 1.1.

SHENZHEN SURENOO TECHNOLOGY CO.,LTD.

A3

Model No.: SLC1602O

www.surenoo.com

Page: 05 of 20

2.SPECIFICATION  

2.1 Display Specification

Item StandardValue Unit

Display Format 16 Characters x 2 Lines --

Display Connector 5P Pin Header / Grove 4P Connector --

FPC Connector N/A --

Operating Temperature -20 ~ +60 ℃

Storage Temperature -30 ~ +70 ℃

Touch Panel Optional No --

Sunlight Readable --

2.2 Mechanical Specification H HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH

Item StandardValue Unit

Outline Dimension 80.00(W) x 36.0(H)x13.0(T) mm

Visual Area 64.50(W) x 16.00(H) mm

Active Area 58.00(W) x 12.46(H) mm

Dot Size 0.61x0.71 mm

Dot Pitch 0.66x0.76 mm

2.3 Electrical Specification

Item StandardValue Unit

IC Package COB --

Controller AIP31068 or Equivalent --

Interface Serial IIC I2C Interface --

2.4 Optical Specification H HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH

Item StandardValue Unit

LCD Type FSTN Positive LCD / Double FSTN Negative LCD --

Viewing Angle Range 6:00 --

Backlight Color RGB --

LCD Duty 1/16 --

LCD Bias 1/5 --

SHENZHEN SURENOO TECHNOLOGY CO.,LTD.

A3

Model No.: SLC1602O

3. OUTLINE DRAWING

www.surenoo.com

Page: 06 of 20



Note: Tolerance is ±0.3 mm unless specified.

1

DO NOT SCALE THIS DRAWING.

MODEL NUMBER :

DWN JIM

APPROVALS

CHK

APP

May-22-19

DATE

PROJECTION SHEET:

GENERAL TOL.

SCALE:

N.T.S.

UNITS

MM

SLC1602L Series

Web: www.surenoo.com Email: [email protected]

1.0

REV. DESCRIPTION OF MODIFY

1'ST DESIGN

MODIFY BY

JIM May-22-2019

DATE

SHENZHEN SURENOO TECHNOLOGY CO.,LTD.

A3

Model No.: SLC1602O

www.surenoo.com

Page: 07 of 20

4.ELECTRICALSPEC

4.1 Pin Configuration

A3

CN1:

Pin No. SYMBOL LEVEL FUNCTION

1 VSS 0V Power Ground

2 VDD +5.0V Power Supply For Logic

3 V0 — Contrast Adjust

4 SCL H/L Serial Clock

5 SDA H/L Serial Data

CN2:

Pin No. SYMBOL LEVEL FUNCTION

1 VSS 0V Power Ground

2 VDD +5.0V Power Supply For Logic

3 SCL H/L Serial Clock

4 SDA H/L Serial Data

SHENZHEN SURENOO TECHNOLOGY CO.,LTD.

A3

Model No.: SLC1602O

www.surenoo.com

Page: 09 of 20

4.

2 Absolute Maximum Ratings

Item Symbol Min. Typ. Max. Unit

Power Supply for Logic VDD-VSS -0.3 - +5.5 V

Logic Supply for LCD VLCD VDD-10 - VDD+0.3 V

Input Voltage VIN -0.3 - VDD+0.3 V

Operating Temperature Top -20 - 70 °C

Storage Temperature TST -30 - 80 °C

Humidity RH - 90%(Max60°C) RH

4.3 Electrical Characteristics

Item Symbol Condition Min. Typ. Max. Unit

V

Power Supply for LCM VDD-VSS VDD=5V 4.5 5.0 5.5

VIL L Level Vss -- 0.5 V

Input Voltage VIH H Level 0.8VDD -- VDD V

Supply Current for LCM IDD - - - 2000 uA

Supply Current for Backlight ILED - - 3*15 3*20 mA



SHENZHEN SURENOO TECHNOLOGY CO.,LTD.

A3

Model No.: SLC1602O

286B283B280B29B446B443B440B5. INSPECTION CRITERIA

HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH287B284281B30B434B45.1 Acceptable Quality Level

288B285B282BEach lot should satisfy the quality level defined as follows

289B286B283BPARTITION 290B287B284BAQL 291B288B285BDEFINITION

292B289B286BA. Major 293B290B287B0.4% 294B291B288BFunctional defective as product

295B292B289BB. Minor 296B293B290B1.5% 297B294B291BSatisfy all functions as product but not satisfy cosmetic stanard

298B295B292BB439B436B433B5.2 Definition of Lot

299B296B293BOne lot means the delivery quantity to customer at one time.

5.3 Condition of Cosmetic Inspection

301B298B295B◆INSPECTION AND TEST

302B299B296B-FUNCTION TEST

303B300B297B-APPEARANCE INSPECTION

304B301B298B-PACKING SPECIFICTION

305B302B299B◆INSPECTION CONDITION

306B303B300B- Put under the lamp (20w¡Á2) at a distance 100mm from

307B304B301B- Tilt upright 45 degree by the front (back) to inspect LCD appearance.

308B305B302B◆AQL INSPECTION LEVEL

309B306B303B- SAMPLING METHOD: MIL-STD-105D

310B307B304B-SAMPLING PLAN: SINGLE

311B308B305B- MAJOR DEFECT: 0.4% (MAJOR)

312B309B306B- MINOR DEFECT: 1.5% (MINOR)

313B310B307B- GENERAL LEVEL: II/NORMAL

www.surenoo.com

Page: 10 of 20

SHENZHEN SURENOO TECHNOLOGY CO.,LTD.

A3

Model No.: SLC1602O

438B315B435B312B432B309B5.4 Module Cosmetic Criteria

NO. Item Judgment Criterion Partition

1 Difference in Spec. None allowed Major

2 Pattern Peeling No substrate pattern peeling and floating Major

No soldering missing Major

No soldering bridge Major

3 Soldering

defects

No cold soldering Minor

4 Resist flaw on substrate Invisible copper foil(￠0.5mm or more)on substrate pattern Minor

No soldering dust Minor

5 Accretion of metallic

Foreign matter No accretion of metallic foreign matters(Not exceed￠0.2mm)

6 Stain No stain to spoil cosmetic badly Minor

7 Plate discoloring No plate fading,rusting and discoloring Minor

8 Solder amount

1.Lead parts

a. Soldering side of PCB

Solder to form a’Filet’

all

around

the

lead.

Solder should not hide the

lead form

perfectly.(too much)

b.Components side

(In case of ‘Through Hole PCB’)

Solder to reach the Components side of PCB

Minor

2.Flat packages Either ‘toe’(A) or ‘heal’ (B) of

the lead to be covered by ‘Filet’.

Lead form to be assume over

Solder.

Minor

3.Chips (3/2) H≧h≧(1/2)H Minor

hH

AB

www.surenoo.com

Page: 11 of 20

SHENZHEN SURENOO TECHNOLOGY CO.,LTD.

A3

Model No.: SLC1602O

9 Backlight defects 1.Light fails or flickers.(Major)

2. Color and luminance do not correspond to specifications.

(Major)

3.Exceeds standards for display’s blemishes, foreign matter,

dark lines or scratches.(Minor)

See

list

←

10 PCB

defects Oxidation or contamination on connectors.*

2. Wrong parts, missing parts, or parts not in specification.*

3.Jumpers set incorrectly.(Minor)

4.Solder(if any)on bezel,LED pad,zebra pad,or screw hole

pad is not smooth.(Minor)

*Minor if display functions correctly.Major if the display fails.

See

list

←

11 Soldering

defects 1. Unmelted solder paste.

2. Cold solder joints,missing solder connections,or oxidation.*

3. Solder bridges causing short circuits.*

4. Residue or solder balls.

5. Solder flux is black or brown.

*Minor if display functions correctly.Major if the display fails.

Minor

www.surenoo.com

Page: 12 of 20

SHENZHEN SURENOO TECHNOLOGY CO.,LTD.

A3

Model No.: SLC1602O

5.5 Screen Cosmetic Criteria (Non-Operating)

No. Defect Judgment Criterion Partition

1 Spots In accordance with Screen Cosmetic Criteria (Operating) No.1. Minor

2 Lines In accordance with Screen Cosmetic Criteria (Operation) No.2. Minor

Size: d mm Acceptable Qty in active area

d≦0.3

0

.

3<d≦1.0

1.0<d≦1.5

1.5<d

Disregard

3

1

0

Minor

3 Bubbles in

Polarizer

4 Scratch In accordance with spots and lines operating cosmetic criteria, When the

light reflects on the panel surface, the scratches are not to be remarkable. Minor

5 Allowable density Above defects should be separated more than 30mm each other. Minor

6 Coloration Not to be noticeable coloration in the viewing area of the LCD panels.

Back-lit type should be judged with back-lit on state only. Minor

7 Contamination Not

to be noticeable. Minor

www.surenoo.com

Page: 13 of 20

SHENZHEN SURENOO TECHNOLOGY CO.,LTD.

A3

Model No.: SLC1602O

5.6 Screen Cosmetic Criteria (Operating)

No. Defect Judgment Criterion Partition

A) Clear Size:d mm Acceptable Qty in active area

d≦0.1

0.1<d≦0.2

0.2<d≦0.3

0.3<d

Disregard

6

2

0

Note: Including pin holes and defective dots which must be within one pixel

Size.

B) Unclear

Size:d mm Acceptable Qty in active area

1 Spots

d≦0.2

0.2<d≦0.5

0.5<d≦0.7

0.7<d

Disregard

6

2

0

Minor

2 Lines A) Clear

Note: () – Acceptable Qty in active area

L - Length (mm)

W -Width(mm)

∞-Disregard

B) Unclear

Minor

‘Clear’ = The shade and size are not changed by Vo.

‘Unclear’ = The shade and size are changed by Vo.

L 5.0

2.0

8

0.020.05 0.1W

See No.1

(0)

(6)

L 10.0

2.0

8

(6)

(0)

0.05 0.3 0.5

See No.1

W

www.surenoo.com

Page: 14 of 20

SHENZHEN SURENOO TECHNOLOGY CO.,LTD.

A3

Model No.: SLC1602O

Judgment Criterion No. Defect Partition

3 Rubbing line Not to be noticeable.

4 Allowable density Above defects should be separated more than 10mm each other. Minor

5 Rainbow Not to be noticeable. Minor

To be 95%~105%of the dot size (Typ.) in drawing.

6 Dot

size Partial defects of each dot (ex.pin-hole) should be treated as’spot’.

(see Screen Cosmetic Criteria (Operating) No.1)

Minor

7 Brightness

(only back-lit

Module)

Brightness Uniformity must be BMAX/BMIN≦2

- BMAX :Max.value by measure in 5 points

- BMIN : Min.value by measure in 5 points

Divide active area into 4 vertically and horizontally.

Measure 5 points shown in the following figure.

Minor

8 Contrast

Uniformity Contrast Uniformity must be BmAX/BMIN≦2

Measure 5 points shown in the following figure.

Dashed lines divide active area into 4 vertically and horizontally.

Measuring points are located at the inter-sections of dashed line.

Note: BMAX – Max.value by measure in 5 points.

BMIN – Min.value by measure in 5 points.

O – Measuring points in ￠10mm.

Minor

Note:

(1) Size : d=(long length + short length)/2

(2) The limit samples for each item have priority.

(3) Complexed defects are defined item by item, but if the number of defects is defined in above table, the total

number should not exceed 10.

www.surenoo.com

Page: 15 of 20

SHENZHEN SURENOO TECHNOLOGY CO.,LTD.

A3

Model No.: SLC1602O

(4) In

case of ‘concentration’, even the spots or the lines of ‘disregarded’ size should not be allowed. Following three

situations

Should be treated as ‘concentration’.

-7 or over defects in circle of ￠5mm.

-10 or over defects in circle of ￠10mm

-20 or over defects in circle of ￠20mm

319B316B313B45B465B462B459B 6.

HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH

PRECAUTIONS FOR USING

HED HHHHHHHHHHHHHHHHH320B317B314B31B445B442B438B6.1 Handling Precautions

321B318B315B◆This device is susceptible to Electro-Static Discharge (ESD) damage. Observe Anti-Static precautions.

322B319B316B◆

323B320B317B◆

324B321B318B◆

325B322B319B◆

326B323B320B◆

display panel is made of glass. Do not subject it to a mechanical shock by dropping it or impact. If

display panel is damaged and the liquid crystal substance leaks out, be sure not to get any in your

mouth. If the substance contacts your skin or clothes, wash it off using soap and water.

Do not apply excessive force to the display surface or the adjoining areas since this may cause the

color tone to vary.

The polarizer covering the display surface of the LCD module is soft and easily scratched. Handle this

polarizer carefully.

If display surface becomes contaminated, breathe on the surface and gently wipe it with a soft dry

cloth. If it is heavily contaminated, moisten cloth with one of the following Isopropyl or alcohol.

327B324B321B◆Solvents other than those above-mentioned may damage the polarizer. Especially, do not use the Water.

328B325B322B◆Exercise care to minimize corrosion of the electrode. Corrosion of the electrodes is accelerated by water

droplets, moisture condensation or a current flow in a high-humidity environment.

329B326B323B◆Install the LCD Module by using the mounting holes. When mounting the LCD module make

sure it is free of twisting, warping and distortion. In particular, do not forcibly pull or bend the cable or the

backlight cable.

330B327B324B◆Do not attempt to disassemble or process LCD module.

331B328B325B◆NC terminal should be open. Do not connect anything.

332B329B326B◆If the logic circuit power is off, do not apply the input signals.

333B330B327B◆To prevent destruction of the elements by static electricity, be careful to maintain an optimum work

environment.

334B331B328B-Be sure to ground the body when handling LCD modules.

335B332B329B-Tools required for assembling, such as soldering irons, must be properly grounded.

336B333B330B-To reduce the amount of static electricity generated, do not conduct assembling and other work under dry

conditions.

337B334B331B-The LCD module is coated with a film to protect the display surface. Exercise care when peeling off this

protective film since static electricity may be generated.

SUR

www.surenoo.com

Page: 16 of 20

SHENZHEN SURENOO TECHNOLOGY CO.,LTD.

A3

Model No.: SLC1602O

6.2 Power Supply Precautions

338B335B332B42B461B458B455B339B336B333B◆Identify and, at all times, observe absolute maximum ratings for both logic and LC drivers. Note that there is

some variance between models.

340B337B334B◆Prevent the application of reverse polarity to VDD and VSS, however briefly.

341B338B335B◆Use a clean power source free from transients. Power-up conditions are occasionally jolting and may

exceed the maximum ratings of modules.

342B339B336B◆The VDD power of module should also supply the power to all devices that may access the

display. Don’t allow the data bus to be driven when the logic supply to the module is turned off. 43B340B337B43B

455B344B452B341B449B338B

6.3 Operating Precautions

345B342B339B◆DO NOT plug or unplug module when the system is powered up.

346B343B340B◆Minimize the cable length between module and host MPU.

347B344B341B◆For models with backlights, do not disable the backlight by interrupting the HV line. Unload inverters

produce voltage extremes that may arc within a cable or at the display.

348B345B342B◆Operate module within the limits of the modules temperature specifications.

349B346B343B44B452B449B446B6.4 Mechanical/Environmental Precautions

350B347B344B◆Improper soldering is the major cause of module difficulty. Use of flux cleaner is not recommended

351B348B345Bas they may seep under the electrometric connection and cause display failure.

352B349B346B◆Mount module so that it is free from torque and mechanical stress.

353B350B347B◆Surface of the LCD panel should not be touched or scratched. The display front surface is an easily

scratched, plastic polarizer. Avoid contact and clean only when necessary with soft, absorbent cotton

dampened with petroleum benzene.

354B351B348B◆Always employ anti-static procedure while handling module.

355B352B349B◆Prevent moisture build-up upon the module and observe the environmental constraints for storage tem

356B353B350B◆Do not store in direct sunlight

357B354B351B◆If leakage of the liquid crystal material should occur, avoid contact with this material, particularly ingestion.

If the body or clothing becomes contaminated by the liquid crystal material, wash thoroughly with water and

soap

468B358B465B355B462B352B

6.5 Storage Precautions

359B356B353B When storing the LCD modules, avoid exposure to direct sunlight or to the light of fluorescent lamps.

360B357B354BKeep modules in bags (avoid high temperature / high humidity and low temperatures below 0C

361B358B355BWhenever possible, LCD modules should be stored in the same conditions in which they were

shipped from our company.

458B362B455B359B452B356B

6.6 Others

363B360B357BLiquid crystals solidify under low temperature (below the storage temperature range) leading to defective

orientation or the generation of air bubbles (black or white). Air bubbles may also be generated if the module

is subject to a low temperature.

364B361B358BIf LCD modules have been operating for a long time showing the same display patterns, the display

patterns may remain on the screen as ghost images and a slight contrast irregularity may also

SUR

SUR SUR

SUR

SUR SUR

SUR

www.surenoo.com

Page: 17 of 20

SHENZHEN SURENOO TECHNOLOGY CO.,LTD.

A3

Model No.: SLC1602O

appear. A normal operating status can be regained by suspending use for some time. It should be noted that

this phenomenon does not adversely affect performance reliability.

365B362B359BTo minimize the performance degradation of the LCD modules resulting from destruction caused by static

electricity etc., exercise care to avoid holding the following sections when handling the modules.

366B363B360B-Exposed area of the printed circuit board.

367B364B361B-Terminal electrode sections.

69B368B466B365B463B 362B

7.USING LCD MODULES HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH HHH

369B366B363B31B450B447B444B7.1 Liquid Crystal Display Modules

LCD is composed of glass and polarizer. Pay attention to the following items when handling.

371B368B365B◆Please keep the temperature within specified range for use and storage. Polarization degradation, bubble

generation or polarizer peel-off may occur with high temperature and high humidity.

372B369B366B◆Do not touch, push or rub the exposed polarizers with anything harder than an HB pencil lead (glass,

tweezers, etc.).

373B370B367B◆N-hexane is recommended for cleaning the adhesives used to attach front/rear polarizers and reflectors

made of organic substances which will be damaged by chemicals such as acetone, toluene, ethanol and

isopropylalcohol.

374B371B368B◆When display surface becomes dusty, wipe gently with absorbent cotton or other soft material

like chamois soaked in petroleum benzin. Do not scrub hard to avoid damaging the display surface.

375B372B369B◆Wipe off saliva or water drops immediately, contact with water over a long period of time may cause

376B373B370Bdeformation or color fading.

377B374B371B◆Avoid contacting oil and fats.

378B375B372B◆Condensation on the surface and contact with terminals due to cold will damage, stain or dirty the polarizers.

After products are tested at low temperature they must be warmed up in a container before coming is

contacting with room temperature air.

379B376B373B◆Do not put or attach anything on display area to avoid leaving marks on.

380B377B374B◆Do not touch the display with bare hands. This will stain the display area and degradate insulation

381B378B375Bbetween terminals (some cosmetics are determinated to the polarizers).

382B379B376B◆As glass is fragile. It tends to become or chipped during handling especially on the edges. Please

383B380B377Bavoid dropping or jarring.

7.2 Installing LCD Modules

384B381B378B42B447B444B441B385B382B379B◆Cover the surface with a transparent protective plate to protect the polarizer and LC cell.

386B383B380B◆When assembling the LCM into other equipment, the spacer to the bit between the LCM and the fitting

387B384B381Bplate should have enough height to avoid causing stress to the module surface, refer to the individual

specifications for measurements. The measurement tolerance should be±0.1mm.

SUR

www.surenoo.com

Page: 18 of 20

SHENZHEN SURENOO TECHNOLOGY CO.,LTD.

A3

Model No.: SLC1602O

7.3 Precaution for Handling LCD Modules

389B386B383BSince LCM has been assembled and adjusted with a high degree of precision; avoid applying

excessive shocks to the module or making any alterations or modifications to it.

390B387B384B◆Do not alter, modify or change the shape of the tab on the metal frame.

391B388B385B◆Do not make extra holes on the printed circuit board, modify its shape or change the positions of

components to be attached.

392B389B386B◆Do not damage or modify the pattern writing on the printed circuit board.

393B390B387B◆Absolutely do not modify the zebra rubber strip (conductive rubber) or heat seal connector.

394B391B388B◆Except for soldering the interface, do not make any alterations or modifications with a soldering iron.

395B392B389B◆Do not drop, bend or twist LCM.

7.4 Electro-Static Discharge Control

397B394B391BSince this module uses a CMOS LSI, the same careful attention should be paid to electrostatic discharge as

for an ordinary CMOS IC.

398B395B392B◆Make certain that you are grounded when handing LCM.

399B396B393B◆Before remove LCM from its packing case or incorporating it into a set, be sure the module and your body

have the same electric potential.

400B397B394B◆When soldering the terminal of LCM, make certain the AC power source for the soldering iron does not leak.

401B398B395B◆When using an electric screwdriver to attach LCM, the screwdriver should be of ground potentiality to

minimize as much as possible any transmission of electromagnetic waves produced sparks coming from the

commutator of the motor.

402B399B396B◆As far as possible make the electric potential of your work clothes and that of the work bench the ground

potential.

403B400B397B◆To reduce the generation of static electricity be careful that the air in the work is not too dried. A relative

humidity of 50%-60% is recommended.

7.5 Precaution for Soldering to LCM

464B404B461B401B458B398B405B402B399B◆Observe the following when soldering lead wire, connector cable and etc. to the LCM.

406B403B400B-Soldering iron temperature : 280℃±10℃

407B404B401B-Soldering time: 3-4 sec.

408B405B402B-Solder: eutectic solder.

409B406B403BIf soldering flux is used, be sure to remove any remaining flux after finishing to soldering operation. (This

does not apply in the case of a non-halogen type of flux.) It is recommended that you protect the LCD

surface with a cover during soldering to prevent any damage due to flux spatters.

410B407B404B◆When soldering the electroluminescent panel and PC board, the panel and board should not be detached

more than three times. This maximum number is determined by the temperature and time conditions

mentioned above, though there may be some variance depending on the temperature of the soldering iron.

411B408B405B◆When remove the electroluminescent panel from the PC board, be sure the solder has completely melted,

the soldered pad on the PC board could be damaged.

SUR

www.surenoo.com

Page: 19 of 20

SHENZHEN SURENOO TECHNOLOGY CO.,LTD.

A3

Model No.: SLC1602O

7.6 Precaution for Operation

413B410B407B◆Viewing angle varies with the change of liquid crystal driving voltage (VO). Adjust VO to show the best

contrast.

414B411B408B◆Driving the LCD in the voltage above the limit shortens its life.

415B412B409B◆Response time is greatly delayed at temperature below the operating temperature range. However, this

does not mean the LCD will be out of the order. It will recover when it returns to the specified temperature

range.

416B413B410B◆If display area is pushed hard during operation, the display will become abnormal. However, it will

return to normal if it is turned off and then back on.

417B414B411B◆Condensation on terminals can cause an electrochemical reaction disrupting the terminal circuit. Therefore,

it must be used under the relative condition of 40℃, 50% RH.

418B415B412B◆When turning the power on, input each signal after the positive/negative voltage becomes stable.

7.7 Limited Warranty

449B419B446B416B443B413B 420B417B414BUnless agreed between and customer, will replace or repair any of its LCD modules which are

found to be functionally defective when inspected in accordance with LCD acceptance standards (copies

available upon request) for a period of one year from date of shipments. Cosmetic/visual defects must be

returned to within 90 days of shipment. Confirmation of such date shall be based on freight documents.

The warranty liability of limited to repair and/or replacement on the terms set forth above. will not

be responsible for any subsequent or consequential events.

7.8 Return Policy

422B419B416BNo warranty can be granted if the precautions stated above have been disregarded. The typical

examples of violations are:

423B420B417B-Broken LCD glass.

424B421B418B-PCB eyelet damaged or modified.

425B422B419B-PCB conductors damaged.

426B423B420B-Circuit modified in any way, including addition of components.

427B424B421B-PCB tampered with by grinding, engraving or painting varnish.

428B425B422B-Soldering to or modifying the bezel in any manner.

429B426B423BModule repairs will be invoiced to the customer upon mutual agreement. Modules must be returned with

sufficient description of the failures or defects. Any connectors or cable installed by the customer must be

removed completely without damaging the PCB eyelet’s, conductors and terminals

430B427B424B.

That’s the end of the datasheet

SUR

SUR SUR SUR

www.surenoo.com

Page: 20 of 20

SHENZHEN SURENOO TECHNOLOGY CO.,LTD.

A3

Model No.: SLC1602O

Surenoo SLC1602O Series User manual

Surenoo SLC1602O Series User manual

Related papers

Other documents