Dometic 3316287.000 Rocker Switch Kit Installation guide

Brand: Dometic

Model: 3316287.000 Rocker Switch Kit

Type: Installation guide

Read these instructions carefully. These

instructions MUST stay with this product.

USA

SERVICE OFFICE

Dometic Corporation

2320 Industrial Parkway

Elkhart, IN 46516

CANADA

Dometic Corporation

46 Zatonski, Unit 3

Brantford, ON N3T 5L8

CANADA

SERVICE CENTER &

DEALER LOCATIONS

Please Visit:

www.eDometic.com

RECORD THIS INFORMATION FOR FUTURE

REFERENCE:

Model Number

Serial Number

Date Purchased

Retailer / Qualied Installer

3316287.000

ROCKER SWITCH KIT

(12 VDC) POWER

REVISION A

Form No. 3316273.000 08/15

(French 3316291.000_A)

LaGrange, IN 46761

INSTALLATION

INSTRUCTIONS

Incorrect [installation / operation / servicing /

maintaining] of this product can lead to seri-

ous injury. Follow all instructions.

The installation MUST comply with all ap-

plicable local and national codes, including

the latest edition of the following standards:

U.S.A.

● ANSI/NFPA70, National Electrical Code

(NEC)

● ANSI/NFPA 1192, Recreational Vehicles

Code

CANADA

●CSA C22.1, Parts l & ll, Canadian Electri-

cal Code

●CSA Z240 RV Series, Recreational

Vehicles

D. General Safety Messages

 Failure to obey the following warn-

ings could result in death or serious injury:

●This product MUST be [installed / serviced] by a

qualied service technician.

●Do NOT modify this product in any way. Modica-

tion can be extremely hazardous.

●Do NOT expose switch to weather, extreme tem-

peratures, or long hours in direct sunlight.

This manual has safety information and instructions to help

you eliminate or reduce the risk of accidents and injuries.

A. Recognize Safety Information

This is the safety alert symbol. It is used to

alert you to potential physical injury hazards.

Obey all safety messages that follow this

symbol to avoid possible injury or death.

B. Understand Signal Words

A signal word will identify safety messages and

property damage messages, and will indicate the

degree or level of hazard seriousness.

 indicates a hazardous situation that,

if NOT avoided, could result in death or serious in-

jury.

 indicates a hazardous situation that,

if NOT avoided, could result in minor or moderate

injury.

 is used to address practices NOT

related to physical injury.

C. Supplemental Directives

Read and follow all safety information and

instructions to avoid possible injury or death.

Read and understand these instructions be-

fore [installing / using / servicing / performing

maintenance on] this product.

IMPORTANT SAFETY INSTRUCTIONS

GENERAL INFORMATION

A. Required Tools

●Crimp Tool

● Phillips Screwdriver

●Wire Cutter

● Saw (jigsaw)

● Drill (electric)

● 7/64″ drill bit

B. Included Hardware

(4) #6-20 x 0.75″ Flat Head Screw

Table 1

Wire Length Wire Size

10′ & Under 14 Gauge

11′ to 30′ 12 Gauge

Over 30′ 10 Gauge

DOCUMENT SYMBOLS

Indicates additional information that is NOT related

to physical injury. Indicates step-by-step instructions.

Wire colors noted within this document are industry

standard. Some RV manufacturers use different col-

ors. Refer to RV manufacturer’s wiring schematics.

A. Switch Panel Mounting Preparation

1.  Do NOT expose switch to weath-

er, extreme temperatures, or long hours in direct

sunlight.

Determine suitable location for switch installa-

tion.

2. Using hand held saw, cut opening in wall or cabi-

net to mount switch panel. See (FIG. 1).

FIG. 1 3.50″

1.75″

Allow 0.50″

clearance on sides.

Allow 0.63″ clearance

on top and bottom.

3. Using switch plate as template, carefully mark

and drill four (4) 7/64″ diameter holes.

B. Wire Switch to 12 Vdc Power Supply

1.  Install a (15 A) fuse (installer sup-

plied) at fuse panel for positive (+) 12 Vdc power

supply ( RED wire) to switch. Otherwise, damage

to unit could occur.

2. Route (2) wires (RED & BLACK; installer sup-

plied) from 12 Vdc power supply to switch.

3. Terminate both wires with 1/4″ female insulated

terminals.

4. Connect positive (+) RED wire to bottom left (+)

switch terminal. See (FIG. 2).

5. Connect negative (-) BLACK wire to top left

GND switch terminal. See (FIG. 2).

C. Wire Switch to Motorized Arm Assembly

1. Route (2) more wires (RED & BLACK; installer

supplied) from switch to right side (motorized)

arm assembly. To avoid voltage drop, follow wire

length guide listed in Table 1.

2. Terminate switch end of wires with 1/4″ female

insulated terminals.

3. Connect positive (+) RED wire to middle left

(MTR) switch terminal. See (FIG. 2).

4. Connect negative (-) BLACK wire to right (MTR)

switch terminal. See (FIG. 2).

5. Connect other end of wires (RED to RED,

BLACK to BLACK) to motorized arm assembly

using properly sized, UL certied butt splice con-

nectors (installer supplied).

Refer to crimp tool manufacturer for crimp-

ing instructions.

D. Wire Track Switch

1.  Install a (15 A) fuse (installer sup-

plied) at fuse panel for positive (+) 12 Vdc power

supply ( RED wire) to switch. Otherwise, damage

to unit could occur.

2. Route RED wire (installer supplied) from 12 Vdc

power supply and connect to terminal 1 on Track

switch. See (FIG. 2).

3. Connect WHITE wire (12 ga.) from Power Chan-

nel wire harness to terminal 2 on Track switch.

See (FIG. 2).

4. Route BLACK wire (installer supplied) from (-)

12 Vdc (ground) and connect to terminal 3 on

Track switch. See (FIG. 2).

5. Connect GREEN wire (12 ga.) from Power

Channel wire harness to ground.

E. Wire LED Switch

1.  Install a (3 A) fuse (installer sup-

plied) at fuse panel for positive (+) 12 Vdc power

supply ( RED wire) to switch. Otherwise, damage

to unit could occur.

2. Route RED wire (installer supplied) from 12 Vdc

power supply and connect to terminal 1 on LED

switch. See (FIG. 2).

3. Connect BLACK wire (12 ga.) from Power Chan-

nel wire harness to terminal 2 on LED switch.

See (FIG. 2).

4. Route BLACK wire (installer supplied) from (-)

12 Vdc (ground) and connect to terminal 3 on

LED switch. See (FIG. 2).

F. Mount Switch Panel

1. Assemble switch panel into previously cut hole.

2. Secure switch panel using #6-20 x 0.75″ at

head screws.

INSTALLATION

SCHEMATIC DRAWING

Track SwitchLED Switch

FIG. 2

Awning Motor

Wire Harness

Red Black

3 Amp

Fuse

15 Amp

Fuse

15 Amp

Fuse

+12 Vdc +12 Vdc

+12 Vdc

Green

Black

RedRed

Black

Red

Black

Power Channel

Wire Harness

White

Dometic 3316287.000 Rocker Switch Kit Installation guide

Dometic 3316287.000 Rocker Switch Kit Installation guide

Dometic 3316287.000 Rocker Switch Kit Installation guide

Related papers