Ryobi HP53LK User guide

Brand: Ryobi

Model: HP53LK

Category: Cordless combi drills

Type: User guide

This manual is also suitable for

Su destornillador ha sido diseñada y fabricado de conformidad con

nuestras estrictas normas para brindar fiabilidad, facilidad de uso

y seguridad para el operador. Con el debido cuidado, le brindará

muchos años de sólido y eficiente funcionamiento.

ADVERTENCIA: Para reducir el riesgo de lesiones,

el usuario debe leer y comprender el manual del operador antes

de usar este producto.

Le agradecemos su compra.

OPERATOR’S MANUAL

MANUEL D’UTILISATION

MANUAL DEL OPERADOR

Tek4® LITHIUM-ION

SCREWDRIVER

REVERSIBLE

TOURNEVIS Tek4® LITHIUM-ION

RÉVERSIBLE

DESTORNILLADOR DE Tek4®

DE IONES DE LITIO

INVERTIBLE

HP53L

Cette tournevis a été conçue et fabriquée conformément à

nos strictes normes de fiabilité, simplicité d’emploi et sécurité

d’utilisation. Correctement entretenue, elle vous donnera des années

de fonctionnement robuste et sans problème.

AVERTISSEMENT : Pour réduire les risques de

blessures, l’utilisateur doit lire et veiller à bien comprendre le

manuel d’utilisation avant d’employer ce produit.

Merci de votre achat.

CONSERVER CE MANUEL POUR

FUTURE RÉFÉRENCE

GUARDE ESTE MANUAL PARA

FUTURAS CONSULTAS

SAVE THIS MANUAL FOR FUTURE REFERENCE

Your screwdriver has been engineered and manufactured to our high standard for dependability, ease of operation, and

operator safety. When properly cared for, it will give you years of rugged, trouble-free performance.

WARNING: To reduce the risk of injury, the user must read and understand the operator’s manual before using

this product.

Thank you for your purchase.

2 — English

 Introduction ..................................................................................................................................................................... 2

 Warranty .......................................................................................................................................................................... 2

 General Power Tool Safety Warnings ...........................................................................................................................3-4

 Screwdriver Safety Warnings .......................................................................................................................................... 4

Symbols ........................................................................................................................................................................... 5

 Features ........................................................................................................................................................................... 6

 Assembly ......................................................................................................................................................................... 6

 Operation ......................................................................................................................................................................7-8

 Maintenance .................................................................................................................................................................... 8

 Figure Numbers (Illustrations) .......................................................................................................................................... 9

 Parts Ordering / Service ....................................................................................................................................Back Page

TABLE OF CONTENTS

INTRODUCTION

This product has many features for making its use more pleasant and enjoyable. Safety, performance, and dependability

have been given top priority in the design of this product making it easy to maintain and operate.

WARRANTY

LIMITED TWO YEAR WARRANTY AND 30 DAY EXCHANGE POLICY

30-DAY EXCHANGE POLICY: During the first 30 days after date of purchasing this product, you may either request service

under this warranty or you may exchange it by returning it with proof of purchase and all original equipment packaged with

the original product to the dealer from which it was purchased. The replacement product will be covered by the limited

warranty for the balance of the two year period from the date of the original purchase.

LIMITED TWO YEAR WARRANTY. This product is warranted against all defects in workmanship or materials for a period

of two years from the date of purchase. The warranty on any accessories for this product, excluding batteries, is limited to

90 days from the date the accessory is purchased. To obtain warranty service, call Customer Service at 1-800-525-2579

for warranty return instructions. The product must be properly packaged and returned with all equipment that was included

with the original product. When you request warranty service, you must also present proof of purchase documentation,

which includes the date of purchase (for example, a receipt or a bill of sale). Defective products returned within the

warranty period will be repaired or replaced, at our option, free of charge, within ninety (90) days or less. The cost of

shipping the product to us is your responsibility. This warranty only covers defects arising under normal usage and does

not cover any malfunction, failure or defects resulting from misuse, abuse, neglect, alteration, modification or unauthorized

repairs. It applies only to the original purchaser at retail, and may not be transferred. One World Technologies, Inc. makes

no warranties, representations or promises as to the quality or performance of this product other than those specifically

stated in this warranty. Any implied warranties granted under state law, including warranties of merchantability or fitness for

a particular purpose, are limited to two years from the date of purchase. One World Technologies, Inc. is not responsible

for direct, indirect, or incidental damages. Some states do not allow limitations on how long an implied warranty lasts, or

the exclusion or limitation of incidental or consequential damages, so the above limitations and exclusions may not apply

to you. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

3 — English

GENERAL POWER TOOL SAFETY WARNINGS

WARNING

Read all safety warnings and instructions. Failure to

follow the warnings and instructions may result in electric

shock, fire and/or serious injury.

Save all warnings and instructions for future reference.

The term “power tool” in the warnings refers to your mains-

operated (corded) power tool or battery-operated (cordless)

power tool.

WORK AREA SAFETY

Keep work area clean and well lit. Cluttered or dark

areas invite accidents.

Do not operate power tools in explosive atmospheres,

such as in the presence of flammable liquids, gases

or dust. Power tools create sparks which may ignite the

dust or fumes.

Keep children and bystanders away while operating a

power tool. Distractions can cause you to lose control.

ELECTRICAL SAFETY

Power tool plugs must match the outlet. Never modify

the plug in any way. Do not use any adapter plugs with

earthed (grounded) power tools. Unmodified plugs and

matching outlets will reduce risk of electric shock.

Avoid body contact with earthed or grounded surfaces

such as pipes, radiators, ranges and refrigerators.

There is an increased risk of electric shock if your body

is earthed or grounded.

Do not expose power tools to rain or wet conditions.

Water entering a power tool will increase the risk of electric

shock.

Do not abuse the cord. Never use the cord for carrying,

pulling or unplugging the power tool. Keep cord away

from heat, oil, sharp edges or moving parts. Damaged

or entangled cords increase the risk of electric shock.

When operating a power tool outdoors, use an

extension cord suitable for outdoor use. Use of a

cord suitable for outdoor use reduces the risk of electric

shock.

If operating a power tool in a damp location is

unavoidable, use a ground fault circuit interrupter

(GFCI) protected supply. Use of a GFCI reduces the risk

of electric shock.

Use battery only with charger listed.

MODEL BATTERY PACK CHARGER

HP53L AP4001 AP4700, AP4500,

AP4800

PERSONAL SAFETY

Stay alert, watch what you are doing and use common

sense when operating a power tool. Do not use a

power tool while you are tired or under the influence

of drugs, alcohol or medication. A moment of inattention

while operating power tools may result in serious personal

injury.

Use personal protective equipment. Always wear eye

protection. Protective equipment such as dust mask, non-

skid safety shoes, hard hat, or hearing protection used for

appropriate conditions will reduce personal injuries.

Prevent unintentional starting. Ensure the switch is in

the off-position before connecting to power source

and/or battery pack, picking up or carrying the tool.

Carrying power tools with your finger on the switch or

energising power tools that have the switch on invites

accidents.

Remove any adjusting key or wrench before turning

the power tool on. A wrench or a key left attached to

a rotating part of the power tool may result in personal

injury.

Do not overreach. Keep proper footing and balance at

all times. This enables better control of the power tool in

unexpected situations.

Dress properly. Do not wear loose clothing or jewellery.

Keep your hair, clothing and gloves away from moving

parts. Loose clothes, jewellery or long hair can be caught

in moving parts.

If devices are provided for the connection of dust

extraction and collection facilities, ensure these are

connected and properly used. Use of dust collection

can reduce dust-related hazards.

Do not wear loose clothing or jewelry. Contain long

hair. Loose clothes, jewelry, or long hair can be drawn

into air vents.

Do not use on a ladder or unstable support. Stable

footing on a solid surface enables better control of the

power tool in unexpected situations.

POWER TOOL USE AND CARE

Do not force the power tool. Use the correct power

tool for your application. The correct power tool will

do the job better and safer at the rate for which it was

designed.

Do not use the power tool if the switch does not turn

it on and off. Any power tool that cannot be controlled

with the switch is dangerous and must be repaired.

Disconnect the plug from the power source and/or

the battery pack from the power tool before making

any adjustments, changing accessories, or storing

power tools. Such preventive safety measures reduce

the risk of starting the power tool accidentally.

Store idle power tools out of the reach of children and

do not allow persons unfamiliar with the power tool

or these instructions to operate the power tool. Power

tools are dangerous in the hands of untrained users.

Maintain power tools. Check for misalignment or

binding of moving parts, breakage of parts and any

other condition that may affect the power tool’s

operation. If damaged, have the power tool repaired

before use. Many accidents are caused by poorly

maintained power tools.

4 — English

GENERAL POWER TOOL SAFETY WARNINGS

Keep cutting tools sharp and clean. Properly maintained

cutting tools with sharp cutting edges are less likely to

bind and are easier to control.

Use the power tool, accessories and tool bits etc.,

in accordance with these instructions, taking into

account the working conditions and the work to

be performed. Use of the power tool for operations

different from those intended could result in a hazardous

situation.

BATTERY TOOL USE AND CARE

Recharge only with the charger specified by the

manufacturer. A charger that is suitable for one type

of battery pack may create a risk of fire when used with

another battery pack.

Use power tools only with specifically designated

battery packs. Use of any other battery packs may create

a risk of injury and fire.

When battery pack is not in use, keep it away from

other metal objects, like paper clips, coins, keys, nails,

screws or other small metal objects, that can make a

connection from one terminal to another. Shorting the

battery terminals together may cause burns or a fire.

Under abusive conditions, liquid may be ejected from

the battery; avoid contact. If contact accidentally

occurs, flush with water. If liquid contacts eyes,

additionally seek medical help. Liquid ejected from the

battery may cause irritation or burns.

SERVICE

Have your power tool serviced by a qualified repair

person using only identical replacement parts. This will

ensure that the safety of the power tool is maintained.

When servicing a power tool, use only identical

replacement parts. Follow instructions in the

Maintenance section of this manual. Use of unauthorized

parts or failure to follow Maintenance instructions may

create a risk of shock or injury.

Hold power tool by insulated gripping surfaces, when

performing an operation where the fastener may

contact hidden wiring. Fasteners contacting a “live” wire

may make exposed metal parts of the power tool “live”

and could give the operator an electric shock.

Use clamps or another practical way to secure and

support the workpiece to a stable platform. Holding

the work by hand or against your body leaves it unstable

and may lead to loss of control.

Know your power tool. Read operator’s manual

carefully. Learn its applications and limitations, as

well as the specific potential hazards related to this

power tool. Following this rule will reduce the risk of

electric shock, fire, or serious injury.

Always wear eye protection with side shields marked

to comply with ANSI Z87.1. Following this rule will

reduce the risk of serious personal injury.

Protect your lungs. Wear a face or dust mask if the

operation is dusty. Following this rule will reduce the risk

of serious personal injury.

Protect your hearing. Wear hearing protection during

extended periods of operation. Following this rule will

reduce the risk of serious personal injury.

Battery tools do not have to be plugged into an

electrical outlet; therefore, they are always in

operating condition. Be aware of possible hazards

when not using your battery tool or when changing

accessories. Following this rule will reduce the risk of

electric shock, fire, or serious personal injury.

Do not place battery tools or their batteries near fire

or heat. This will reduce the risk of explosion and possibly

injury.

 Do not crush, drop or damage battery pack. Do not

use a battery pack or charger that has been dropped

or received a sharp blow. A damaged battery is subject

to explosion. Properly dispose of a dropped or damaged

battery immediately.

Batteries can explode in the presence of a source

of ignition, such as a pilot light. To reduce the risk of

serious personal injury, never use any cordless product

in the presence of open flame. An exploded battery can

propel debris and chemicals. If exposed, flush with water

immediately.

Do not charge battery tool in a damp or wet location.

Following this rule will reduce the risk of electric shock.

For best results, your battery tool should be charged

in a location where the temperature is more than 50°F

but less than 94°F. To reduce the risk of serious personal

injury, do not store outside or in vehicles.

Under extreme usage or temperature conditions,

battery leakage may occur. If liquid comes in contact

with your skin, wash immediately with soap and water.

If liquid gets into your eyes, flush them with clean

water for at least 10 minutes, then seek immediate

medical attention. Following this rule will reduce the risk

of serious personal injury.

 Save these instructions. Refer to them frequently and

use them to instruct others who may use this tool. If you

loan someone this tool, loan them these instructions

also.

SCREWDRIVER SAFETY WARNINGS

5 — English

SYMBOLS

Some of the following symbols may be used on this product. Please study them and learn their meaning. Proper

interpretation of these symbols will allow you to operate the product better and safer.

Safety Alert Indicates a potential personal injury hazard.

Read Operator’s Manual

To reduce the risk of injury, user must read and understand

operator’s manual before using this product.

Eye Protection

Always wear eye protection with side shields marked to comply

with ANSI Z87.1

Wet Conditions Alert Do not expose to rain or use in damp locations.

Li - Ion

Recycle Symbols

This product uses lithium-ion (Li-ion) batteries. Local, state or

federal laws may prohibit disposal of batteries in ordinary trash.

Consult your local waste authority for information regarding

available recycling and/or disposal options.

V Volts Voltage

Hz Hertz Frequency (cycles per second)

W Watt Power

min Minutes Time

Direct Current Type or a characteristic of current

No Load Speed Rotational speed, at no load

.../min Per Minute Revolutions, strokes, surface speed, orbits etc., per minute

SYMBOL NAME

DESIGNATION/EXPLANATION

The following signal words and meanings are intended to explain the levels of risk associated with this product.

DANGER:

Indicates an imminently hazardous situation, which, if not avoided, will result

in death or serious injury.

WARNING:

Indicates a potentially hazardous situation, which, if not avoided, could result

in death or serious injury.

CAUTION:

Indicates a potentially hazardous situation, which, if not avoided, may result in

minor or moderate injury.

CAUTION:

(Without Safety Alert Symbol) Indicates a situation that may result in property

damage.

SYMBOL SIGNAL MEANING

WARNING:

Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals

known to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:

•leadfromlead-basedpaints,

•crystallinesilicafrombricksandcementandothermasonryproducts,and

•arsenicandchromiumfromchemically-treatedlumber.

Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to

these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust masks

that are specially designed to filter out microscopic particles.

6 — English

FEATURES

PRODUCT SPECIFICATIONS

Motor ........................................................................4 V DC

Switch ..................................................... On-Off/Reversible

No Load Speed .................................200/600 r/min. (RPM)

Clutch .............................................................. 24 Positions

Torque .................................................................... 40 in. lb.

Collet ........................................SPEEDLOAD +™ SYSTEM

KNOW YOUR SCREWDRIVER

See Figure 1, page 9.

The safe use of this product requires an understanding of

the information on the tool and in this operator’s manual as

well as a knowledge of the project you are attempting. Before

use of this product, familiarize yourself with all operating

features and safety rules.

DIRECTION OF ROTATION SELECTOR

(FORWARD/REVERSE/CENTER LOCK)

Your screwdriver has a direction of rotation (forward/

reverse/center lock) selector located above the switch

trigger for changing the direction of bit rotation. Setting

the direction of rotation selector in the OFF (center lock)

position helps reduce the possibility of accidental starting

when not in use.

LED WORKLIGHT

The screwdriver has a built-in LED worklight that illuminates

when the switch trigger is depressed. This feature is conve-

nient when working in close or tight areas where additional

light is needed.

SPEEDLOAD +™ SYSTEM

Your screwdriver has the SPEEDLOAD +™ SYSTEM, the

fastest and most convenient way to change any 1/4 in. hex

shank bits.

TORQUE ADJUSTMENT RING

Your screwdriver has a 24-position clutch. The torque

adjustment ring can be turned to select the right amount of

torque for the application.

TWO-SPEED GEAR TRAIN

The two-speed gear train is designed for drilling or driv-

ing at low (Position 1) or high (Position 2) speeds. A slide

switch is located on top of your screwdriver for selecting

the speed setting.

ASSEMBLY

UNPACKING

This product has been shipped completely assembled.

 Carefully remove the product and any accessories from

the box. Make sure that all items listed in the packing list

are included.

WARNING:

Do not use this product if it is not completely assembled

or if any parts appear to be missing or damaged. Use of

a product that is not properly and completely assembled

could result in serious personal injury.

 Inspect the product carefully to make sure no breakage

or damage occurred during shipping.

 Do not discard the packing material until you have care-

fully inspected and satisfactorily operated the product.

 If any parts are damaged or missing, please call

1-800-525-2579 for assistance.

PACKING LIST

4V Screwdriver

Bit Set

Operator’s Manual

WARNING:

If any parts are damaged or missing do not operate this

product until the parts are replaced. Use of this product

with damaged or missing parts could result in serious

personal injury.

WARNING:

Do not attempt to modify this product or create acces-

sories not recommended for use with this product. Any

such alteration or modification is misuse and could result

in a hazardous condition leading to possible serious

personal injury.

WARNING:

To prevent accidental starting that could cause serious

personal injury, always remove the battery pack from the

product when assembling parts.

7 — English

 Place the cap over the battery pack and push down

until the cap meets the threads at the end of the battery

compartment.

 Screw the cap on securely.

To remove the battery pack:

Unscrew the cap. The battery pack will disconnect and

be easy to remove.

Do not attempt to use this product if the battery cap is

not securely closed.

DIRECTION OF ROTATION SELECTOR

(FORWARD/REVERSE/CENTER LOCK)

See Figure 3, page 9.

The direction of bit rotation is reversible and is controlled

by a selector located above the switch trigger. With the

screwdriver held in normal operating position, the direction

of rotation selector should be positioned to the left of the

switch trigger for forward motion. The direction is reversed

when the selector is to the right of the switch trigger.

Setting the direction of rotation selector in the OFF (center

lock) position helps reduce the possibility of accidental

starting when not in use.

CAUTION:

To prevent gear damage, always allow the collet to

come to a complete stop before changing the direction

of rotation.

To stop the screwdriver, release the switch trigger and allow

the collet to come to a complete stop.

NOTE: The screwdriver will not run unless the direction of

rotation selector is pushed fully to the left or right.

TWO-SPEED GEAR TRAIN

See Figure 4, page 9.

The screwdriver has a two-speed gear train designed for low

(Position 1) or high (Position 2) speeds. A slide switch is

located on top of the screwdriver to select the speed setting.

When using screwdriver in the low speed range (Position

1), speed will decrease and unit will have more power and

torque. When using screwdriver in the high speed range

(Position 2), speed will increase and unit will have less

power and torque. When drilling use 1/4 in. hex shank drill

bits only. Maximum drill size is 1/4 in.

Use the high speed setting to drill holes, and use the low

speed setting for driving screws.

TO LOAD/RELEASE BITS

See Figure 5, page 9.

The SPEEDLOAD +™ SYSTEM on the screwdriver is a quick

change chuck designed to accept any 1/4 in. hex bits. Insert

the bit into the chuck and push as far as possible until the

chuck locks onto the bit. To remove a bit, push rubber collar

forward, and then pull the bit straight out of the chuck.

OPERATION

WARNING:

Do not allow familiarity with products to make you

careless. Remember that a careless fraction of a second

is sufficient to inflict serious injury.

WARNING:

Always wear eye protection with side shields marked to

comply with ANSI Z87.1. Failure to do so could result in

objects being thrown into your eyes resulting in possible

serious injury.

WARNING:

Do not use any attachments or accessories not

recommended by the manufacturer of this product. The

use of attachments or accessories not recommended

can result in serious personal injury.

APPLICATIONS

You may use this product for the purposes listed below:

Drivingscrewswithscrewdriverbits

Light-dutydrilling

WARNING:

Battery products are always in operating condition.

Therefore, the switch should always be locked when not

in use or carrying at your side.

BATTERY PROTECTION FEATURES

Ryobi lithium-ion batteries are designed with features that

protect the lithium-ion cells and maximize battery life.

If the tool stops during use, release the trigger to reset and

resume operation. If the tool still does not work, the battery

needs to be recharged.

TO INSTALL / REMOVE BATTERY PACK

See Figure 2, page 9.

WARNING:

Always remove battery pack from the product when you

are assembling parts, making adjustments, cleaning, or

when not in use. Removing battery pack will prevent acci-

dental starting that could cause serious personal injury.

To install the battery pack:

 Unscrew the battery cap.

 Insert the battery pack in the direction shown. Make sure

the raised rib on the battery pack aligns with the groove

in the compartment.

8 — English

ADJUSTABLE TORQUE CLUTCH

This screwdriver is equipped with an adjustable torque clutch

for driving different types of screws into different materials.

The proper setting depends on the type of material and the

size of screw you are using.

ADJUSTING TORQUE

See Figure 6, page 9.

There are twenty-four torque indicator settings located on

the front of the screwdriver.

 Select the gear train setting to high (Position 2) or low

(Position 1) speed.

 Rotate the adjusting ring to the desired setting.

• 1-4 Fordrivingsmallscrews(Position 1 or 2)

• 5-8 Fordrivingscrewsintosoftmaterial

(low speed - Position 1))

• 9-12 Fordrivingscrewsintosoftandhard

materials (low speed - Position 1)

• 13-16 For driving screws into hard wood

(low speed - Position 1)

• 17-24 Fordrivinglargescrews

(low speed - Position 1)

NOTE: During use, if the screwdriver stalls and begins to

make a clicking sound, and the LED worklight pulses on

and off, you should release the switch trigger immediately.

This indicates that you have overloaded the tool. Depress

the switch trigger again to resume operation.

To avoid this situation, avoid forcing the tool and refer to

the settings described above to be sure you are using the

screwdriver for its intended application.

LED WORKLIGHT

See Figure 7, page 9.

The screwdriver has a built-in LED worklight. This feature

is convenient when working in close or tight areas where

additional light is needed. Whenever the switch trigger is

depressed, the LED worklight will illuminate.

OPERATION

MAINTENANCE

WARNING:

When servicing, use only identical replacement parts.

Use of any other parts may create a hazard or cause

product damage.

WARNING:

Always wear eye protection with side shields marked to

comply with ANSI Z87.1 during maintenance. If operation

is dusty, also wear a dust mask.

GENERAL MAINTENANCE

Avoid using solvents when cleaning plastic parts. Most

plastics are susceptible to damage from various types of

commercial solvents and may be damaged by their use. Use

clean cloths to remove dirt, dust, oil, grease, etc.

WARNING:

Do not at any time let brake fluids, gasoline, petroleum-

based products, penetrating oils, etc., come in contact

with plastic parts. Chemicals can damage, weaken or

destroy plastic which may result in serious personal

injury.

STORAGE

Before storing, always remove the battery pack from the

battery compartment.

BATTERY PACK PREPARATION FOR

RECYCLING

WARNING:

Upon removal, cover the battery pack’s terminals with

heavy-duty adhesive tape. Do not attempt to destroy or

disassemble battery pack or remove any of its compo-

nents. Lithium-ion batteries must be recycled or disposed

of properly. Also, never touch both terminals with metal

objects and/or body parts as short circuit may result.

Keep away from children. Failure to comply with these

warnings could result in fire and/or serious injury.

NOTE: FIGURES

(ILLUSTRATIONS) START ON

PAGE 9 AFTER FRENCH AND

SPANISH LANGUAGE SECTIONS.

Page is loading ...

 





   _______________________

   

 

            



 



 



HP53L





OPERATOR’S MANUAL / Tek4® LITHIUM-ION SCREWDRIVER

REVERSIBLE

MANUEL D’UTILISATION / TOURNEVIS Tek4

® LITHIUM-ION

RÉVERSIBLE

MANUAL DEL OPERADOR / DESTORNILLADOR DE Tek4® DE IONES DE LITIO

INVERTIBLE

HP53L

ONE WORLD TECHNOLOGIES, INC.



É

www.ryobitools.com

®

 





   

    

 





 



 







®



®

 





   _________________________

    _________________________

 





 





 



HP53L

Ryobi HP53LK User guide

Brand: Ryobi

Model: HP53LK

Category: Cordless combi drills

Type: User guide

This manual is also suitable for

Download PDF

report

in other languages

français: Ryobi HP53LK Mode d'emploi
español: Ryobi HP53LK Guía del usuario

Ryobi HP53LK User guide

This manual is also suitable for

Ryobi HP53LK User guide

in other languages

Related papers

Other documents