Indesit LFT 114/HA User guide

Page is loading ...

Operating instructions

Contents

Installation, 14-15

Positioning and levelling

Connecting the water and electricity supplies

Advice regarding the first wash cycle

Technical data

Ecodesign Regulation

Description of the appliance, 16

Overall view

Control panel

Loading the racks, 17

Lower rack

Cutlery basket

Upper rack

Start-up and use, 18

Starting the dishwasher

Measuring out the detergent

Wash options

Wash cycles, 19

Table of wash cycles

Rinse aid and refined salt, 20

Measuring out the rinse aid

Measuring out the refined salt

Care and maintenance, 21

Shutting off the water and electricity supplies

Cleaning the dishwasher

Preventing unpleasant odours

Cleaning the sprayer arms

Cleaning the water inlet filter

Cleaning the filters

Leaving the machine unused for extended

periods

Precautions and advice, 22

General safety

Disposal

Saving energy and respecting the environment

Troubleshooting, 23

Assistance, 24

Before calling for Assistance

English,13

EN

LFT 114

DISHWASHER

EN

14

Installation

Keep this instruction manual in a safe place for

future reference. If the appliance is sold, given away or

moved, please ensure the manual is kept with the

machine, so that the new owner may benefit from the

advice contained within it.

Please read this instruction manual carefully: it

contains important information regarding the safe

installation, use and maintenance of the appliance.

If the appliance must be moved at any time, keep it in

an upright position; if absolutely necessary, it may be

tilted onto its back.

This appliance is intended to be used in household

and similar applications such as:

- staff kitchen areas in shops, offices and other working

environments;

- farm houses;

- by clients in hotels, motels and other residential type

environments;

- bed and breakfast type environments.

Positioning and levelling

1. Remove the appliance from all packaging and check

that it has not been damaged during transportation.

If it has been damaged, contact the retailer and do not

proceed any further with the installation process.

2. Check the dishwasher by placing it so that its sides or

back panel are in contact with the adjacent cabinets or

even with the wall. This appliance can also be recessed

under a single worktop

* (

see the Assembly instruction

sheet

).

3. Position the dishwasher on a level and sturdy floor. If

the floor is uneven, the front feet of the appliance may be

adjusted until it reaches a horizontal position. If the

appliance is levelled correctly, it will be more stable and

much less likely to move or cause vibrations and noise

while it is operating.

4. Adjust the height of the rear foot from the front of the

appliance

* on the central lower part of the dishwasher, turning

a hexagonal spanner (red color) with an opening of 8 mm in a

clockwise direction to increase the height or in an

anticlockwise direction to decrease the height.

Connecting the water and electricity

supplies

Connection to the water and electricity supplies

should only be performed by a qualified technician.

The dishwasher should not stand on top of the water

hoses or the electricity supply cable.

The appliance must be connected to the water

supply network using new hoses.

Do not use old hoses.

The water inlet and outlet hoses and the electricity

supply cable may be positioned towards the right or the

left in order to achieve the best possible installation.

Connecting the water inlet hose

• To a suitable cold water connection point: before

attaching the hose, run the water until it is perfectly

clear so that any impurities that may be present in the

water do not clog the appliance; after performing this

operation, screw the inlet hose tightly onto a tap with

a ¾ gas threaded connection.

• To a suitable hot water connection point: your

dishwasher may be supplied with hot water from the

mains supply (if you have a central heating system

with radiators) provided that it does not exceed a

temperature of 60°C.

Screw the hose to the tap as described for connection

to a cold water supply.

If the inlet hose is not long enough, contact a

specialist store or an authorised technician (

see

Assistance

).

The water pressure must be within the values

indicated in the Technical data table (

see adjacent

information

).

The hose should not be bent or compressed.

Connecting the water outlet hose

Connect the outlet hose (without bending it) to a drain

duct with a minimum diameter of 4 cm.

The outlet hose must be at a height ranging from 40 to

80 cm from the floor / surface where the dishwasher

rests (A).

Before connecting the water outlet hose to the sink

drain, remove the plastic plug (B).

* Only available in selected models.

EN

15

Anti-flooding protection

To ensure floods do not occur, the dishwasher:

- is provided with a special system which blocks the

water supply in the event of anomalies or leaks from

inside the appliance.

Some models are also equipped with the supplementary

safety device

New Acqua Stop

*, which guarantees anti-

flooding protection even in the event of a supply hose

rupture.

WARNING: HAZARDOUS VOLTAGE!

Under no circumstance should the water inlet hose be

cut as it contains live electrical parts.

Electrical connection

Before inserting the plug into the electrical socket, make

sure that:

• The socket is earthed and complies with current

regulations.

• The socket can withstand the maximum load of the

appliance, which is indicated on the data plate

located on the inside of the door (

see chapter entitled

Description of the appliance

).

• The power supply voltage falls within the values

indicated on the data plate on the inside of the door.

• The socket is compatible with the plug of the

appliance. If this is not the case, ask an authorised

technician to replace the plug (

see Assistance

); do

not use extension cables or multiple sockets.

Once the appliance has been installed, the power

supply cable and the electrical socket should be easily

accessible.

The cable should not be bent or compressed.

If the power supply cable is damaged, it must be re-

placed by the manufacturer or its Technical Assistance

Service in order to prevent all potential hazards. (See As-

sistance)

The Company shall not be held responsible for any

incidents that occur if these regulations are not

observed.

Anti-condensation strip*

After installing the dishwasher, open the door and stick

the adhesive transparent strip under the wooden shelf in

order to protect it from any condensation which may

form.

Advice regarding the first wash cycle

After the appliance has been installed, immediately

before running the first wash cycle, completely fill the

salt dispenser with water and add only then

approximately 1 kg of salt (

see chapter entitled Rinse aid

and refined salt

). The water may overflow: this is normal

and is not a cause for concern. Select the water

hardness value (

see chapter entitled Rinse aid and

refined salt

). - After the salt has been poured into the

machine, the LOW SALT indicator light* switches off.

If the salt container is not filled, the water softener

and the heating element may be damaged as a result.

Technical data

Dimensions

width 59.5 cm

height 82 cm

depth 57 cm

Capacity 12 standard place-settings

Water supply

pressure

0,05 ÷ 1MPa (0.5 ÷ 10 bar)

7,25 – 145 psi

Power supply

voltage

See appliance data plate

Total absorbed

power

See appliance data plate

Fuse See appliance data plate

This dishwasher conforms to the

following European Community

Directives:

-2006/95/EC (Low Voltage)

-2004/108/EC (Electromagnetic

Compatibility)

2005/32/EC (Comm. Reg,

1275/2008) (Ecodesign)

-97/17/EC (Labelling)

-2002/96/EC (Waste Electrical

and Electronic Equipment WEEE)

ECODESIGN REGULATION

ECO wash cycle is the standard cycle to which the energy label data refers; this cycle can be used to wash crockery with a normal

soil level and is the most efficient in terms of energy and water consumption for this type of crockery. To reduce consumption even

further, only run the dishwasher when it is full.

Standby consumption: Left-on mode consumption: 3 W – Off mode consumption: 1,3 W

Consumption data table for the main cycles

* Cycle data refers to the values recorded in a laboratory, in accordance with European standard EN 50242.

** Data is obtained by recording values when the appliance is operational and loaded with user crockery.

Standard conditions* User conditions**

Energy consumption

(kWh/cycle)

Water consumption

(l/cycle)

Duration

(min/cycle)

Energy consumption

(kWh/cycle)

Water consumption

(l/cycle)

Duration

(min/cycle)

INTENSIVE

1,60 16 150 1,40 15 135

NORMAL

1,30 16 120 1,10 15 110

EN

16

Overall view

Description of the

appliance

1. Upper rack

2. Upper sprayer arm

3. Tip-up compartments

4. Rack height adjuster

5. Lower rack

6. Lower sprayer arm

7. Cutlery basket

8. Washing filter

9. Salt dispenser

10. Detergent and rinse aid dispensers

11. Data plate

12. Control Panel

***

Control panel

***Only in completely built-in models.

* Only available in selected models.

The number and type of wash cycles and options may vary depending on the dishwasher model.

ON/OFF/RESET

button

ON/OFF

indicator light

Select wash

cycle button

Wash cycle indicator lights

EN

17

Loading the racks

* Only available in selected models. The number and

position may vary.

Before loading the racks, remove all food residue from

crockery and empty liquids from glasses and cups.

After loading the appliance, make sure that the sprayer

arms can rotate freely.

Lower rack and cutlery basket

The lower rack can hold pans, lids, plates, salad bowls, cutlery, etc.

Large plates and lids should ideally be placed at the sides of the rack.

Several dishwasher models are fitted with tip-up sections

*,

which can be used in a vertical position when arranging plates

or in a horizontal position when arranging saucepans, salad

bowls and frying pans.

The type of cutlery basket may vary (modular or non-modular)

according to the dishwasher model. The non-modular basket must

only

be positioned at the front of the lower rack.

Both are fitted with

grilles over the top,

for improved

cutlery arrange-

ment.

Knives and other utensils with sharp edges must be

placed in the cutlery basket with the points facing

downwards, or they must be positioned horizontally in the tip-

up compartments on the upper rack.

Upper rack

Load this rack with delicate and lightweight crockery: glasses,

cups, saucers and shallow salad bowls.

Adjustable position tip-up compartments

The tip-up compartments

can be positioned at

different heights, to

optimise the arrangement

of crockery throughout

the rack. Wine glasses

can be placed safely in

the tip-up compartments,

by inserting the stem of

each glass into the

corresponding slots.

Adjusting the height of the upper rack

In order to make it easier to arrange the crockery, the upper

rack may be moved to a higher or lower level.

The height of the upper rack should ideally be adjusted

WHEN THE RACK IS EMPTY.

NEVER raise or lower the rack on one side only.

Open the left and right guide rail stops

and pull out the rack; position it higher

or lower as required, slide it along the

guide rails until the front wheels are in

place and close the stops (

see figure

).

If the rack is fitted with Dual Space

handles

* (

see figure

), pull out the

upper rack until it reaches its stop

point, grip the handles at the sides of

the rack and move it upwards or

downwards, then slowly let it fall back

into place.

Items that should not be washed in the

dishwasher

• Wooden items, objects with wooden or horn handles or

glued-on parts.

• Items made from aluminium, copper, brass, pewter or tin.

• Items made from plastic material which is not heat-resistant.

• Antique or hand-painted porcelain.

• Antique silver. Silver that is not antique may, however, be

washed in the dishwasher using a delicate wash cycle,

provided that it does not come into contact with other

metals.

We recommend the use of crockery which is dishwasher

safe.

EN

18

Start-up and use

Measuring out the detergent

A good wash result also depends on the correct

amount of detergent being used; exceeding the

stated amount does not result in a more effective

wash and increases environmental pollution.

Only use detergent which has been specifically

designed for dishwashers.

DO NOT USE washing up liquid.

Using excessive detergent may result in foam

residue remaining in the machine after the cycle

has ended.

The use of tablets is only recommended for

models which offer the MULTI-FUNCTIONAL

TABLETS option.

To achieve the best results from each washing

and drying cycle, powder detergent, rinse aid

liquid and salt should be used.

Compartment A: Washing detergent

Compartment B: Pre-wash detergent

1. Open cover C by pressing

button D.

2. Pour in the detergent after

consulting the

Table of wash

cycles

:

• For powder detergent use

compartments A and B.

• For detergent in tablet form:

when the cycle requires 1 tablet, place it in compartment

A and close the cover; when it requires 2, place the

second tablet at the bottom of the appliance.

3. Remove detergent residues from the edges of the

compartment and close the cover until it clicks.

* Only available in selected models.

Starting the dishwasher

1. Turn the water tap on.

2. Open the door and press the ON/OFF button: you will

hear a short beep and the ON/OFF and wash cycle

indicator lights switch on for a few seconds.

3. Measure out the detergent (

see below

).

4. Load the racks (

see chapter entitled Loading the

racks

).

5. Select the wash cycle in accordance with the type of

crockery and its soil level (

see Table of wash cycles

), by

pressing the P button; the indicator light corresponding

to the selected wash cycle will switch on.

7. Start the wash cycle by shutting the door: after a few

seconds have passed, a long beep signals the start of

the wash cycle.

8. Two short beeps and one long one indicate the end of

the wash cycle and the indicator light corresponding to

the wash cycle flashes slowly. Open the door, switch off

the appliance by pressing the ON/OFF button, shut off

the water tap and unplug the appliance from the

electricity socket.

9. Wait for a few minutes before removing the crockery,

in order to avoid burns. Unload the racks, beginning with

the lower level.

- The machine will switch off automatically

during certain periods of inactivity, in order to

minimise electricity consumption.

Modifying a wash cycle in progress

If a mistake was made during the wash cycle selection

process it is possible to change the cycle, provided that it

has only just begun: open the door, taking care to avoid the

escaping steam, and press and hold the ON/OFF button;

the machine will switch off with a long beep. Switch the

machine back on using the ON/OFF button and select the

new wash cycle using the P button; start the cycle by

closing the door.

Adding extra crockery

Without switching off the machine, open the door, taking

care to avoid the escaping steam, and place the

crockery inside the dishwasher. Close the door: the

cycle starts from the point at which it was interrupted.

Accidental interruptions

If the door is opened during the wash cycle, or if there is

a power cut, the cycle stops. It starts again from the point

at which it was interrupted once the door has been shut

or the electricity supply is restored.

EN

19

Wash cycles

If the crockery is only lightly soiled or if it has been rinsed with water before being placed in the

dishwasher, reduce the amount of detergent used accordingly.

The number and type of wash cycles and options may vary depending on the dishwasher model.

Notes:

To make it easier to measure out the detergent, it is worth remembering that:

1 tablespoon = 15 grams of powder = approximately 15 ml of liquid - 1 teaspoon = 5 grams of powder = approximately 5

ml of liquid

* The Eco wash cycle adheres to the regulation EN-50242. Although it has a longer duration than other wash cycles it

uses less energy and is les harmful to the environment.

Note for Test Laboratories: for information relating to comparative EN testing conditions, please send an email to the

following address: [email protected]

Detergent

(A) = compartment A

(B) = compartment B

Wash cycle

Selection

instructions

Wash cycle

Powder Liquid Tablets

Drying

Wash cycle

duration

(tolerance

±10%)

Hrs. Min.

Environmentally-friendly

wash cycle

*

with low energy

consumption levels, suitable

for pans and dishes.

Eco

*

25 g (A)

5 g (B)

25 ml (A)

5 ml (B)

1 (A) Yes 2:55’

Normally soiled pans and

dishes. Standard daily wash

cycle.

Normal

25 g (A)

5 g (B)

25 ml (A)

5 ml (B)

1 (A) Yes 1:50’

Preliminary wash cycle for

dishes while the load is

awaiting completion with the

dishes from the next meal.

Soak

No

0:08’

Extremely soiled dishes and

pans (not to be used for

delicate items).

Intensive

30 g (A)

30 ml (A)

1 (A)

Yes 2:25’

EN

20

Rinse aid and refined salt

Only use products which have been

specifically designed for dishwashers.

Do not use table salt or industrial salt, or

washing up liquid.

Follow the instructions given on the packaging.

If using a multi-functional product it is not necessary to

add rinse aid; however, we recommend that you add salt,

especially if you live in an area where the water is hard

or very hard. Follow the instructions given on the

packaging.

If you do not add salt or rinse aid, the LOW

SALT

* and LOW RINSE AID* indicator lights

remain lit.

Measuring out the rinse aid

Rinse aid makes it easier for the crockery to dry, as water

runs off surfaces more readily and therefore does not leave

streaks or marks.

The rinse aid dispenser should be filled:

• When the LOW RINSE AID

* indicator light on the control

panel is illuminated;

1. Open the dispenser by turning the

lid (G) in an anticlockwise direction.

2. Pour in the rinse aid, making sure

it does not overflow from the

dispenser. If this happens, clean the

spill immediately with a dry cloth.

3. Screw the lid back on.

NEVER pour the rinse aid

directly into the appliance tub.

Adjusting the amount of rinse aid

If you are not completely satisfied with the drying results,

you may adjust the quantity of rinse aid used. Use a

screwdriver to turn the dosage adjuster (F) to one of the 6

pre-set positions (the default position is set to 4):

• If there are streaks on the crockery, set the adjustment

device to a lower number (1-3).

• If drops of water remain on the crockery or if there are

limescale marks present after the cycle has finished, set

the adjuster to a higher number (4-6).

Setting the water hardness

Every dishwasher is equipped with a water softener which, by

using refined salt designed especially for this type of

appliance, supplies water without limescale which is then used

to wash the crockery.

This dishwasher offers a setting which helps to reduce

pollution and optimises washing performance in accordance

with the water hardness level in your area. This information can

be obtained from the organisation which supplies your

household with water.

- Open the door and switch on the machine by pressing the

ON/OFF button.

- Press the P button and hold for approximately 5 seconds;

two short beeps will sound and the indicator light

corresponding to the set degree of hardness will flash

slowly on the display (the water softening system is set to

number 2).

- Press the P button repeatedly until the desired hardness

level has been reached (1-2-3-4-5

*

see Water hardness

table

).

E.g. hardness 1 (indicator light 1 flashing)

hardness 2 (indicator light 1 illuminated, indicator light 2

flashing).

hardness 3 (indicator lights 1 and 2 illuminated, indicator light

3 flashing and so on), up to a maximum of 5

* leves.

To exit the function, wait a few seconds or press one of the

option buttons

*, or switch off the machine using the ON/OFF

button.

Even if using multi-functional tablets, the salt dispenser should

still be filled.

(°dH = hardness measured in German degrees - °f =

hardness measured in French degrees - mmol/l = millimoles

per litre)

Measuring out the refined salt

In order to achieve the best possible results using a wash

cycle, make sure that the dispenser is never empty. Refined

salt removes limescale from the water, thus avoiding the

formation of deposits on crockery.

The salt dispenser is located in the lower part of the

dishwasher (

see Description

) and should be filled:

• When the green float

* cannot be seen by simply looking at

the cap of the salt dispenser.

• When the LOW SALT

* indicator light on the control panel is

illuminated;

1. Remove the lower rack and unscrew the

container cap (anticlockwise).

2. The first time you do this: fill the water tank

right up to its edge.

3. Position the funnel

* (

see figure)

and fill the

salt container right up to its edge (this should hold

approximately 1 kg); it is not unusual for a little water to leak

out.

4. Remove the funnel

* and wipe any salt residue away from

the opening; rinse the cap under running water and then

screw it on, the head facing downwards so as to let the water

flow out of the four cracks which are arranged in a star shape

on the lower part of the cap. (Salt cap with green float

*)

It is advisable to perform this procedure every time you

add salt to the container.

Make sure the cap is screwed on tightly, so that no detergent

can get into the container during the wash cycle (this could

damage the water softener beyond repair).

When necessary, measure out the salt before a wash

cycle so that any saline solution which has leaked out of the

salt dispenser is removed.

* Only available in selected models.

G

F

Water Hardness Table

Average salt

container capacity

duration

**

level °dH °fH mmol/l months

1 0 - 11 0 - 20 1,1 - 2

5 months

2 12 - 17 21 - 30 2,1 - 3

3 months

3 17 - 34 31 - 60 3,1 - 6

2 months

4

*

34 - 50 61 - 90 6,1 - 9

2/3 weeks

For values between 0°f and 10°f, we do not recommend the

use of salt.

*

this setting may cause a slight increase in the duration of

the cycles.

**

for 1 wash cycle per day.

EN

21

Care and maintenance

Shutting off the water and electricity

supplies

• Turn off the water tap after every wash cycle to avoid

leaks.

• Always unplug the appliance when cleaning it and

when performing maintenance work.

Cleaning the dishwasher

• The external surfaces of the machine and the control

panel may be cleaned using a non-abrasive cloth

which has been dampened with water. Do not use

solvents or abrasive products.

• Any marks on the inside of the appliance may be

removed using a cloth dampened with water and a

little vinegar.

Preventing unpleasant odours

• Always keep the door of the appliance ajar in order to

avoid moisture from forming and being trapped inside

the machine.

• Clean the seals around the door and detergent

dispensers regularly using a damp sponge. This will

avoid food becoming trapped in the seals, which is

the main cause behind the formation of unpleasant

odours.

Cleaning the sprayer arms

Food residue may become encrusted onto the sprayer

arms and block the holes used to spray the water. It is

therefore recommended that the arms are checked from

time to time and cleaned with a small non-metallic

brush.

The two sprayer arms may both be removed.

To remove the upper sprayer

arm, rotate the locking ring in

an anti-clockwise direction.

The upper sprayer arm should

be replaced with the holes

facing upwards.

The lower sprayer arm can be

removed by pressing on the

side tabs and pulling it

upwards.

Cleaning the water inlet filter*

If the water hoses are new or have not been used for an

extended period of time, let the water run to make sure it

is clear and free of impurities before performing the

necessary connections. If this precaution is not taken,

the water inlet could become blocked and damage the

dishwasher.

Clean the water inlet filter at the tap outlet regularly.

- Turn off the water tap.

- Unscrew the end of the water inlet hose, remove the filter

and clean it carefully under running water.

- Replace the filter and screw the water hose back into

position.

Cleaning the filters

The filter assembly consists of three filters which remove

food residues from the washing water and then recirculate

the water. They should be cleaned if you wish to achieve

the best results in every wash.

Clean the filters regularly.

The dishwasher should not be used without filters, or if

the filter is loose.

• After several washes, check the filter assembly and if

necessary clean it thoroughly under running water, using a

non-metallic brush and following the instructions below:

1.1.

1. Turn the cylindrical filter C in an anti-clockwise direction

and pull it out (fig. 1).

2.2.

2. Remove the cup filter B by exerting a slight pressure on

the side flaps (fig. 2).

3.3.

3. Slide out the stainless steel plate filter A (fig. 3).

4.

Inspect the trap and remove any food residue. NEVER

REMOVE the wash cycle pump (black detail)

(fig. 4)

.

After cleaning the filters, replace the filter assembly and fix it

in position correctly; this is essential for maintaining the

efficient operation of the dishwasher.

Leaving the machine unused for

extended periods

• Disconnect the appliance from the electricity supply and

shut off the water tap.

• Leave the door of the appliance ajar.

• When you return, run a wash cycle when the dishwasher

is empty.

* Only available in selected models.

2

C

B

4

1

3

EN

22

Precautions and advice

This appliance was designed and manufactured in

compliance with current international safety standards.

The following information has been provided for safety

reasons and should therefore be read carefully.

General safety

• This appliance is not intended for use by persons

(including children) with reduced physical, sensory or

mental capabilities, or lack of experience and

knowledge, unless they have been given supervision

or instruction concerning use of the appliance by a

person responsible for their safety.

• Children should be supervised to ensure that they do

not play with the appliance.

• The appliance was designed for domestic use inside

the home and is not intended for commercial or

industrial use.

• The appliance must be used by adults only, to wash

domestic crockery in accordance with the

instructions in this manual.

• The appliance must not be installed outdoors, even in

covered areas. It is extremely dangerous to leave the

machine exposed to rain and storms.

• Do not touch the appliance when barefoot.

• When unplugging the appliance always pull the plug

from the mains socket, do not pull on the cable.

• The water supply tap must be shut off and the plug

should be removed from the electrical socket before

cleaning the appliance or carrying out any

maintenance work.

• If the appliance breaks down, do not under any

circumstances touch the internal parts in an attempt

to perform the repair work yourself.

• Never touch the heating element.

• Do not lean or sit on the open door of the appliance:

this may cause the appliance to overturn.

• The door should not be left open as it may create a

dangerous obstacle.

• Keep detergent and rinse aid out of reach of children.

• The packaging material should not be used as a toy.

Disposal

• Disposal of packaging materials: observe local

legislation so that the packaging may be reused.

• The European Directive 2002/96/EC relating to Waste

Electrical and Electronic Equipment (WEEE) states

that household appliances should not be disposed of

using the normal solid urban waste cycle. Exhausted

appliances should be collected separately in order to

optimise the cost of re-using and recycling the

materials inside the machine, while preventing

potential damage to the atmosphere and to public

health. The crossed-out dustbin is marked on all

products to remind the owner of their obligations

regarding separated waste collection.

For further information relating to the correct disposal

of household appliances, owners may contact the

relevant public authority or the local appliance

dealer.

Saving energy and respecting the

environment

Saving water and energy

• Only begin a wash cycle when the dishwasher is full.

While waiting for the dishwasher to be filled, prevent

unpleasant odours using the Soak cycle (

see Wash

cycles

).

• Select a wash cycle which is suited to the type of

crockery and to the soil level of the crockery using the

Table of wash cycles

:

- For dishes with a normal soil level, use the Eco wash

cycle, which guarantees low energy and water

consumption levels.

- If the load is smaller than usual activate the Half load

option

* (

see Start-up and use

).

• If your electricity supply contract gives details of

electricity saving time bands, run wash cycles during

the periods when a lower tariff is applied. The

Delayed start

* button (

see Start-up and use

) helps

you organise the wash cycles accordingly.

Phosphate-free and chlorine-free detergents

containing enzymes

• We strongly recommend that you use detergents that

do not contain phosphates or chlorine, as these

products are harmful to the environment.

• Enzymes provide a particularly effective action at

temperatures around 50°C, and as a result detergents

containing enzymes can be used in conjunction with

low-temperature wash cycles in order to achieve the

same results as a normal 65°C wash cycle.

• To avoid wasting detergent, use the product in

appropriate quantities based on the manufacturer’s

recommendations, the hardness of the water and the

soil level and quantity of crockery to be washed. Even

if they are biodegradable, detergents contain

substances which may alter the balance of nature.

* Only available in selected models.

EN

23

Troubleshooting

Whenever the appliance fails to work, check for a solution from the following list before calling for

Assistance.

Problem:

Possible causes / Solutions:

The dishwasher does not start or

cannot be controlled

• Switch off the appliance by pressing the ON/OFF button, switch it back on after

approximately one minute and reset the program.

• The appliance has not been plugged in properly.

• The dishwasher door has not been shut properly.

The door won’t close • The lock was released. Strongly push the door until a “clacking” noise is heard.

No water drains out from the

dishwasher.

• The dishwasher cycle has not yet finished.

• The water inlet hose is bent (see Installation).

• The drain duct is blocked.

• The filter is clogged up with food residues.

The dishwasher makes excessive

noise.

• The dishes are rattling against each other or against the sprayer arms.

• An excessive amount of foam has been produced: the detergent has not been

measured out correctly or it is not suitable for use in dishwashers (see Start-up

and use).

The dishes and glasses are

covered in a white film or

limescale deposits.

• The level of the refined salt is low or the dosage setting is not suited to the

hardness of the water (see Rinse aid and salt).

• The lid on the salt dispenser is not closed properly.

• The rinse aid has been used up or the dosage is too low.

The dishes and glasses are

streaked or have a bluish tinge.

• The rinse aid dosage is too high.

The crockery has not been dried

properly.

• A wash cycle without a drying program has been selected.

• The rinse aid has been used up or the dosage is too low (see Rinse aid and

salt).

• The rinse aid dispenser setting is not suitable.

• The crockery is made from non-stick material or plastic.

The dishes are not clean. • The racks are overloaded (see Loading the racks).

• The crockery has not been arranged well.

• The sprayer arms cannot move freely.

• The wash cycle is too gentle (see Wash cycles).

• An excessive amount of foam has been produced: the detergent has not been

measured out correctly or it is not suitable for use in dishwashers (see Start-up

and use).

• The lid on the rinse aid compartment has not been shut correctly.

• The filter is dirty or blocked (see Care and maintenance).

• The refined salt level is low (see Rinse aid and salt).

The dishwasher does not take any

water in - Tap shut-off alarm

(several short beeps

*

are emitted)

(the 2 (Normal) and 3 (Soak) WASH

CYCLES indicator lights flash).

• There is no water in the mains supply.

• The water inlet hose is bent (see Installation).

• Turn on the tap and the appliance will start after a few minutes.

• The appliance lock has been activated because no action was taken when the

beeps

*

sounded.

Switch off the appliance using the ON/OFF button, turn on the tap and switch

the appliance back on after 20 seconds by pressing the same button. Re-

program the appliance and restart the wash cycle.

Water inlet hose alarm / Water inlet

filter blocked

(the 1 ECO), the 2 (Normal) and the

3 (Soak) WASH CYCLES indicator

lights flash).

• Switch off the appliance by pressing the ON/OFF button. Shut off the water tap

to eliminate the risk of flooding and remove the plug from the electrical socket.

Make sure the water inlet filter has not become blocked by impurities (see “Care

and maintenance” chapter).

* Only available in selected models.

EN

24

Before contacting Assistance:

• Check whether the problem can be resolved using the Troubleshooting guide (

see Troubleshooting

).

• Restart the programme to check whether the problem has ceased to exist.

• If the problem persists, contact the Authorised Technical Assistance Service.

Never use the services of unauthorised technicians.

Please have the following information to hand:

• The type of malfunction.

• The appliance model (Mod.).

• The serial number (S/N).

This information can be found on the appliance data plate (

see Description of the appliance

).

Assistance

Page is loading ...

Indesit LFT 114/HA User guide

Indesit LFT 114/HA User guide

in other languages