Bosch kgs 46123 ff Owner's manual

Page is loading ...

16

A

16

de

- Abdeckung, Schrauben und

Unterlagscheibe (1-2-3) entfernen

- Griff ca. 5 mm nach außen schieben (4)

- Vorsichtig ohne Drehen am Griff ziehen (5)

- Stopfen entfernen und durch neue ersetzen

- Neuen Griff in umgekehrter Reihenfolge der

Schritte 5 – 1 montieren (7-8-9-10-11)

en

- Remove closing part, screws and washer

(1-2-3)

- Push handle appox. 5mm through

outside (4)

- Pull handle carefully without turning (5)

- Remove and replace hole closing pins (6)

- Apply the handle disassembly operation

from 5 to 1 for fixing of the handle

(7-8-9-10-11)

fr

- Enlevez l'insert enfiché (1), les vis (2) et la

plaquette intercalaire (3)

- Tirez la poignée d'env. 5 mm vers

l'extérieur (4)

- Tirez doucement la poignée (5) sans tourner

- Enlevez les bouchons obturant les trous puis

remplacez-les par des bouchons neufs (6)

- Montez la nouvelle poignée dans l'ordre

chronologique inverse des étapes

5 à 1 (7-8-9-10-11)

it

- Rimuovere elemento ad innesto, viti e

rondella (1-2-3)

- Spingere la maniglia ca. 5 mm verso l’esterno (4)

- Tirare delicatamente la maniglia senza ruotare (5)

- Rimuovere i tappi di chiusura fori e sostituirli

con tappi nuovi (6)

- Montare la maniglia nuova procedendo

nell’ordine inverso delle operazioni

5 - 1 (7-8-9-10-11).

de Inhaltsverzeichnis

Hinweise zur Entsorgung und Sicherheit 4, 5

Bestimmungen 5

Umgebungstemperatur beachten 5

Gerät aufstellen 6

Gerät kennenlernen 7-9

Einschalten und Temperaturwahl 10

Ausschalten, Gerät stillegen 11

Lebensmittel einordnen 11, 12

Gefrieren und Lagern 12-14

Reinigen 15

Energiespartips 16

Hinweise zu Betriebsgeräuschen 16

Kleine Störungen selbst beheben 17, 18

Kundendienst 18

en Index

Disposal and safety information 19, 20

Regulations 20

Observe ambient temperature 20

Installation 21

Getting to know your appliance 22-24

Switching ON and setting temperatures 25

Switching OFF and longer periods of disuse 26

Food arrangement 26, 27

Freezing and storing 27-29

Cleaning 30

Power saving tips 31

Information about operating noises 31

Minor problems and how to rectify them yourself 32, 33

Customer Service 33

fr Sommaire

Mise au rebut, conseils de sécurité et consignes 34, 35

Conditions 35

Consignes relatives à la température ambiante 35

Installation de l'appareil 36

Faire la connaissance de l’appareil 37-39

Mise en service et sélection de la température 40

Coupure et mise hors service de l’appareil 41

Rangement des aliments 41, 42

Congélation et stockage 42-44

Nettoyage 45

Economies d'énergie 46

Remarques sur les bruits de fonctionnement 46

Réparer soi-même les petites pannes 47, 48

Service après-vente 48

it Indice

Avvertenze per lo smaltimento e la sicurezza 49, 50

Norme 50

Osservare la temperatura ambiente 50

Installazione dell'apparecchio 51

Conoscere l'apparecchio 52-54

Inserimento e selezione della temperatura 55

Disinserire, mettere fuori servizio l’apparecchio 56

Sistemazione degli alimenti 56, 57

Congelare e conservare 57-59

Pulizia 60

Consigli per il risparmio energetico 61

Avvertenze sui rumori di funzionamento 61

Eliminare da soli piccoli guasti 62, 63

Servizio assistenza clienti 63

Page is loading ...

19

en

Disposal and safety information

Notes on disposal

Old appliances still have some residual

value. An environment-friendly method

of disposal will ensure that valuable raw

materials can be recovered and used again.

Unplug your old appliance, cut through the

mains cable and throw away cable and plug

together.

Remove the door lock so that children at

play cannot become trapped inside and risk

suffocation.

The refrigerant used in fridge/freezers and

the gases in the insulation material require

special disposal procedures. Ensure that

none of the pipes on the back of the

appliance are damaged prior to disposal.

Your new appliance was protected by

adequate packaging while it was on its way

to you. All materials used for this purpose

are environment-friendly and suitable for

recycling. Please contribute to protecting the

environment by disposing of the packaging

appropriately.

Do not allow children to play with any

parts of the packaging. There is a risk of

suffocation by the cardboard boxes and

plastic wrapping.

Up-to-date information concerning options

for disposing of your old appliance and the

packaging from the new one can be obtained

from your retailer or local council office.

This appliance is labelled in

accordance with European Directive

2002/96/EG concerning used

electrical and electronic appliances

(waste electrical and electronic equipment -

WEEE). The guideline determines the

framework for the return and recycling of

used appliances as applicable throughout

the EU

As a contribution to environmental

protection, we use recycled paper.

Safety information

Before starting the appliance for the first

time, you should read the information

contained in the operating and installation

instructions carefully. This information is vital

for the installation, operation and servicing

of the appliance.

Keep the operating and installation

instructions in a safe place and remember to

hand them over to any subsequent owner.

The manufacturer shall not be liable if the

following instructions are not observed:

l Never start up an appliance showing any

signs of damage. If in doubt, consult your

dealer.

l Installation and connection of the

appliance must be carried out according

to the installation instructions. Supply

conditions and data must coincide with

the data on the rating plate.

l Do not under any circumstances use

a steam cleaner on this appliance. The

steam could come into contact with live

parts of the appliance and cause a short-

circuit or electric shock.

l Electrical safety of the appliance is only

guaranteed if the household earthing

system has been installed in compliance

with regulations.

l Disconnect appliance from the mains in

case of malfunction and when cleaning or

servicing the appliance. Either withdraw

the plug or turn off at the fuse. Pull the

plug itself and not the cable.

l Repairs and maintenance of the appliance

should only be performed by a qualified

technician. Incorrect repairs carried out

by someone unqualified are a potential

source of danger that may have critical

consequences for the user of the

appliance.

l Bottles containing high-proof alcoholic

drinks should be properly sealed and

stored standing up.

Products that make use of a flammable

propellant gas (e.g. whipped cream

sprays, aerosols) and explosive

21

en

20

en

Installation

Siting

A dry and adequately ventilated room is the

best location for installing the appliance.

Remember that the appliance should not be

exposed to direct sunlight, nor should it be

close to a direct source of heat such as a

cooker, radiator, etc. Where installation close

to a heat source is unavoidable, ensure

that a suitable insulating panel is used or

maintain the following minimum clearances

between the appliance and the heat source:

3 cm clearance (electric cookers)

30 cm clearance (oil or coal-fired stoves).

If the appliance is placed next to another

refrigerator or freezer, keep a minimum 2 cm

clearance at the side in order to prevent

condensation.

The appliance must be stable and level. To

compensate for an uneven floor, use the two

height-adjustable feet at the front of the

appliance, Fig. E.

Two castors at the rear of the appliance

facilitate installation into a recess.

Changing over door hinges

Proceed in numerical sequence (Fig. F).

Electrical connection

Only connect appliances to a 220–240 V/

50 Hz a.c. supply by means of a safety

socket installed in accordance with

regulations.

Make sure that the socket is protected by

a 10 amp fuse or higher.

With appliances destined for non-European

countries, check the rating plate to make

sure that supply voltage and type of current

indicated coincide with the values of your

power supply. The rating plate is located at

the bottom left of the refrigerator. Figure

D

.

In the event that the mains cable needs to

be replaced, this must only be carried out by

a service technician of the manufacturer.

Warning! NEVER connect the appliance to

electronic energy saver plugs (e.g. Sava

plug) or to power inverters which convert

the direct current to 230 V alternating

current (e.g. solar equipment, power

supplies on ships).

Ventilation

Figure

3

The warm air generated at the back of

the appliance must be allowed to escape

unhindered. Otherwise the refrigerating

machine will have to work harder which in

turn increases energy consumption. For this

reason, never cover up the vents and grilles.

After shipping ...

Before switching on for the first time, allow

the appliance to set vertically for

approximately 1/2 hour.

substances should not be stored inside

this appliance – explosion hazard!

l Liquids in bottles and cans, in particular

carbonated drinks, should never be stored

in the freezer as the bottles and cans will

burst.

l Do not cover or block the vents or grilles

of your appliance.

l Do not use the base panel, pull-out parts,

doors etc. to stand or lean on.

l Do not allow children to play with this

appliance.

l If the appliance is fitted with a lock, keep

the key in a safe place out of the reach of

children.

l Never put ice cubes or ice lollies straight

from the freezer into your mouth. (The low

temperature may cause “freezer burns”.)

l Never touch any frozen food if your hands

are wet, as they may stick to it.

l WARNING: Keep ventilation openings, in

the appliance enclosure or in the built-in

structure, clear of obstruction.

l WARNING: Do not damage the refrigerant

circuit.

l WARNING: Do not use electrical

appliances inside the food storage

compartements of the appliance,unless

they are of the type recommended by the

manufacturer.

This unit contains the coolant

isobutane (R 600a), a natural

gas which is very

environmentally friendly but

also combustible. When transporting and

installing the unit care must be taken to

ensure that none of the refrigeration

circuit components become damaged. In

the event of damage avoid naked flames

or ignition sources and ventilate the room

in which the unit is placed for a few

minutes.

Warning - Do not use mechanical devices

or other artificial means to accelerate the

defrosting process, other than those

recommended dy the manufacturer.

Disposal and safety information

Regulations

The appliance is suitable for refrigerating

and freezing food, and making ice cubes.

It is designed for domestic use.

If using the appliance for commercial

purposes, please observe the statutory

regulations applicable for the trade sector in

question.

The appliance adheres to current German

regulations for the prevention of accidents

caused by refrigerating equipment (VBG 20).

This product meets all the relevant safety

regulations applicable to electrical appliances.

The refrigerating circuit has been leak-tested.

Observe ambient

temperature

Depending on the “climatic category” (see

rating plate), the appliance can be operated

at the following ambient temperatures.

(The rating plate can be found inside the

appliance at the bottom left-hand side.

Fig.

D

).

Climatic Ambient temperature

category from ... to

SN +10 °C to 32 °C

N +16 °C to 32 °C

ST +18 °C to 38 °C

T +18 °C to 43 °C

If the temperature drops below the ambient-

temperature range, the refrigerator compart-

ment will become too cold. If the temperature

exceeds the ambient-temperature range, the

freezer compartment will become too warm.

If the ambient temperature drops below the

set temperature in the refrigerator, the latter

will drop to the ambient temperature.

At ambient temperatures below +10 °C,

functional irregularities may occur during

automatic defrosting of the refrigerator

interior.

23

en

22

en

Getting to know your appliance

The fully automatic NO FROST system

ensures that ice does form inside the

freezer section. There is no longer any

need for defrosting.

How it works:

The food is frozen by a flow of cold air.

The evaporator in the NO FROST system

cools the air inside the appliance. The cold

air is circulated by a fan. A second fan

provides for air circulation in the refrigerator

compartment.The moisture in the air

condenses on the evaporator which is

defrosted fully automatically whenever

necessary.

The thawed water is directed to the

refrigerating unit where it evaporates. The

freezer section and the frozen food inside

are kept free from ice.

Description of control

functions

Figure

2

1 Button

Appliance main switch, serves for

switching on and off the entire appliance.

2 "Super" button for refrigerator

compartment

Used for switching "super cooling" on

and off. Display "SU" 4 and display 5

(orange lamp) indicate that "super

cooling" is on. When "fast cooling" has

been switched on, the refrigerator

compartment is cooled for 6 hours at the

coldest temperature selector setting. The

temperature in the refrigerator

compartment is then switched back to

the set temperature. "Fast cooling" is

ideal for the rapid cooling of beverages.

3 Button for selecting temperature in

refrigerator compartment

(The temperature in the refrigerator

compartment can be selected from +2

0

C

to +8

0

C)

Press the selection button repeatedly or

continuously until the desired

temperature is displayed. (The

temperature selection is displayed

consecutively from +8

0

C to +2

0

C.

+8

0

C is redisplayed after +2

0

C).

4 Temperature display for refrigerator

compartment

Indicates two functions :

a) Selected temperature for

refrigerator compartment

b) Display "SU" (super cooling)

When the Super button 2 is pressed,

"SU" is displayed.

Getting to know your appliance

Before reading on, please unfold the pages

at the back of this manual featuring the

illustrations.

These operating instructions apply to

various models. It is possible that some

details of the illustrations do not coincide

exactly with the particular characteristics

of your appliance.

General view

Figure

1

1-11 Control panel

12 Air vent opening

13 Interior light

14 Multiflow system

(cold air distributor)

15 Shelf

16 Drawer for yoghurt cartons

17 Fruit and vegetable container

18 "Chiller" compartment

19 Tray for small cans, tubes

20 Butter and cheese compartment

21 Bottle rack

22 Egg rack

23 Bottle holder

24 Bottle shelf

25 Freezer tray

26 Frozen-food container

27 Frozen-food calendar

A Fridge section

B Freezer section

Control panel

(Quick guide)

Figure

2

1 Button

Appliance main switch for on/off

2 "super" button

Maximum capacity for Refrigerator

Compartment

3 Temperature selection button for

Refrigerator Compartment

Colder/Warmer

4 Display for Refrigerator Compartment:

Selected temperature

5 "super" display of Refrigerator

Compartment

6 "super" display of Freezer

Compartment

7 Display for Freezer Compartment

a) Selected temperature

b) "warmest" temperature

c) "AL" (alarm) display

8 "alarm" display

9 Temperature selection button for

Freezer Compartment

Colder/Warmer

10 "super" button

Maximum capacity for Freezer

Compartment

11 "alarm" button ("alarm off" switch)

a) For switching off the warning buzzer.

b) For displaying the warmest

temperature which has prevailed in the

freezer compartment (only if display 7

flashes).

25

en

24

en

Getting to know your appliance

5 "super" display (cool)

Illuminates only if "fast cooling" is on.

6 "super" display (freeze)

Illuminates only if "fast freeze" is on.

7 Temperature display for freezer

compartment

Indicates three functions :

a) Selected temperature for freezer

compartment

b) "AL"(alarm) display

Is displayed when the freezer

compartment is too warm.

c) "Warmest temperature" in the

freezer compartment

If "AL" flashes on display 7, the freezer

compartment was too warm due to a

power failure or a fault in the freezer

compartment.

When the Alarm Off button is pressed,

the warmest temperature reached in

the freezer compartment is indicated

on display 7 for five seconds.

This value is then cleared – "AL"

(Alarm) is then indicated on display 7

without flashing.

8 The "alarm" display

Illuminates and the warning tone sounds

simultaneously, when it becomes too

warm in the freezer compartment.

This extinguishes when the freezer

compartment has reached its operation

temperature.

9 Button for selecting temperature in

freezer compartment

Press the selection button repeatedly or

continuously until the desired

temperature is displayed. The value last

selected is stored. (The temperature

selection is displayed consecutively from

-16

0

C to -26

0

C. -16

0

C is redisplayed

after -26

0

C).

Note

"AL" (Fig. 2/7) is displayed if the freezer

compartment is too warm caused by a

power failure or a fault. The temperature can

be selected by pressing the selection button

9. The selected temperature is displayed for

5 seconds. "AL" is then redisplayed. The

selected temperature is displayed as soon

as the freezer compartment has reached the

selected temperature.

10 "super" button

Serves to switch fast-freeze on and off.

Display "SU" 7 and the "Super" display 6

(orange lamp) indicate that "super

cooling" is on. The fast freezing serves

for freezing of large quantities of fresh

food and should be switched on up to

24 hours before placing the fresh food

in the freezer compartment.

The refrigerating unit operates continually

after being switched on, a very low

temperature is achieved in the freezer

compartment.

11 "alarm" button

Serves for switching off the warning

buzzer.

The warning buzzer sounds if the freezer

temperature is too warm, i.e. if the

frozen-food is in danger (display 9 flashes

simultaneously).

There are occasions when the warning

buzzer may sound without the frozen-

food being in any danger:

- when you start up the appliance

- when placing fresh food in the freezer

without switching on fast freezing

- and if the freezer compartment door is

open too long.

Once the warning buzzer has been

switched off, the "acoustic warning"

automatically returns to stand-by, if the

freezer compartment has reached its

operating temperature again.

Switching ON and setting temperatures

Fig.

2

l Put the plug in the socket.

l When the buttons are pressed, an

acknowledgement signal is emitted.

l Press the appliance main switch 1.

Warning signal is emitted, refrigerator

temperature display (4 °C) 4 and "Alarm"

display 8 illuminate. "AL" (Alarm) 7

flashes.

l Press "alarm" button 11.

Press the Alarm Off button 11. Warning

signal stops and the "warmest

temperature" is indicated on display 7 for

5 seconds. "AL" 7 stops flashing. The

appliance is now running.

l Set the temperature for the freezer

compartment.

Repeatedly press or hold down the

selection button 9 until the required

temperature is displayed. The value last

selected is saved. (The temperature

selection is displayed consecutively from

-16 °C to –26 °C. –16 °C is redisplayed

after –26 °C).

We recommend setting the temperature

of the freezer compartment at -20

0

C.

Note

"AL" is indicated on display 7 if the freezer

compartment is too warm caused by a

power failure or a fault. The freezer

compartment temperature can be selected

by pressing the selection button 9. The

selected temperature is indicated for 5

seconds on display 7. "AL" is then

redisplayed. The selected temperature is

indicated on display 7 as soon as the freezer

compartment has reached the selected

temperature.

l Set the temperature for the refrigerator

compartment.

Press the selection button 3 repeatedly or

continuously until the desired temperature

is displayed. The value last selected is

stored. (The temperature selection is

displayed continuously from 8

0

C to 2

0

C.

8

0

C is redisplayed after 2

0

C).

We recommend setting the temperature

of the refrigerator compartment at 4

0

C.

Note

l The temperature in the refrigerator

compartment may fluctuate because:

– The appliance door is opened frequently

– Large quantities of fresh food are placed

in the refrigerator compartment and/or

freezer compartment

– The ambient temperature changes

– The temperature-selector setting for the

freezer compartment changes or

"super" freeze has been activated.

l To prevent condensation in the area of

the door seal, the sides of the housing

are partially heated.

27

en

26

en

Food arrangementFood arrangement

When loading the food,

note the following:

l Allow warm food and beverages to cool

down before storing inside the appliance.

l Ensure that food is well wrapped or

covered before it is stored. This will pre-

vent food from dehydrating, deteriorating

in colour or losing in taste and will help

maintain freshness. It will also prevent

cross-flavouring. Vegetables, fruit and

salad need not be wrapped provided they

are stored in the vegetable bins of the

refrigerator.

l Never let any oil or grease come into

contact with plastic fittings or the door

seal as these materials easily become

porous.

l Never store any explosive substances

inside the appliance. High-proof alcohol

should only be stored upright in tightly

sealed containers.

Danger of explosion!

l Glass bottles containing liquid that can

freeze should never be stored in the

freezer as the glass bursts when the

contents freeze.

Example of food

arrangement

Fig.

1

Refrigerator compartment (A)

Bread, cakes and pastries, ready-made

meals and dairy products, from top to

bottom on the shelves (15).

Cheese, sausages and yoghurt in the

drawer (16).

Fruit, vegetables and salads in the

vegetable container (17).

Small bottles and cans on the shelf (19).

Butter and cheese in the compartment (20).

Large bottles on the bottle shelf (24).

Switching OFF

Press the main switch, Figure

2

/1. The

whole appliance is then switched off.

Longer periods of disuse

If the appliance is not going to be used for

a longer period of time:

Press the main switch, Figure

2

/1, clean

the appliance and leave the doors open.

Switching OFF and longer

periods of disuse

Freezer compartment (B)

Use the freezer tray (25) to store small

frozen goods and make ice cubes.

Use the top frozen goods containers (26)

to store frozen foods.

Interior fittings

The shelves in the refrigerator compartment

can be re-arranged when the door is opened

at a 90° angle. Pull the shelf forwards, lower,

pull out and re-insert in the desired position

(Fig.

4

).

Bottle rack

Bottles can be placed and stacked securely in

the recesses (Fig.

5

).

"Chiller" compartment (Fig.

9

)

Pull the base of the compartment forwards,

the flap opens.

The temperature in this compartment is

lower than in the refrigerator compartment.

The temperature may therefore drop below

0 °C. Ideal for storing fish, meat and

sausage.

But not suitable for lettuce, vegetables

and cold-sensitive produce.

The small drawer can be taken out to

facilitate insertion and removal of food

(Figure

7

).

The egg racks inserted into the door shelves

can be folded up to enable tubes, small tins,

etc. to be stacked in their place.

The bottle rack is provided with a retainer to

prevent bottles from falling over when the

door is opened or closed, Figure

8

/A.

All trays, racks and containers attached

to the door can be removed for cleaning

purposes.

To remove, simply lift them up, Fig.

6

/A

Freezing and storing

Note the following when

buying frozen food

l Inspect packaging: it should not be

damaged in any way.

l Make sure the “Best before ...” date has

not expired.

l Check thermometer of the vendor's

freezer. It should read –18 °C or colder.

l Ensure that the frozen foods are the last

items to be bought. Wrap in several layers

of newspaper or place in a thermo-

insulated bag and take home at once.

Store frozen products in the freezer with-

out delay.

Freezing at home

If freezing at home, use only foodstuffs which

are absolutely fresh and in perfect condition.

Foodstuffs that freeze well

Meat, cold slices and sausage, poultry and

game, fish, vegetables, aromatic herbs, fruit,

bread and pastries, pizza, precooked meals,

leftovers, egg yolks and whites.

Foodstuffs not suitable for freezing

Whole eggs in their shells, soured cream

and mayonnaise, lettuces, radishes,

horseradish and onions.

Blanching vegetables and fruit

It is advisable to blanch vegetables and fruit

before freezing in order to preserve colour,

flavour, aroma and vitamin C.

(To blanch, bring a large saucepan of water

to a fast boil and completely immerse fruit or

vegetables briefly. Most book stores offer a

wide selection of literature on freezing which

will also deal with blanching.)

Wrapping food

Pack the food in portions suitable for your

household.

Vegetable and fruit portions should be no

heavier than 1 kg, while meat portions can

29

en

28

en

be up to 2.5 kg. Smaller portions freeze

through more quickly and the quality is

thereby maintained better when defrosting

and preparing the food.

It is important to seal food airtight before

freezing to prevent it from losing its taste

or dehydrating.

Suitable wrapping materials:

plastic foil, polyethylene tubular film,

aluminium foil and freezing containers.

These items are available from any dealer.

Unsuitable wrapping materials:

wrapping paper, greaseproof paper, cello-

phane, bin bags or used carrier bags.

Place food in the wrapping, press out any

air and seal it airtight.

Suitable sealing materials:

rubber bands, plastic clips, string, freezer

tape or similar. Polyethylene tubular film and

bags may be heat-sealed using a special

sealing iron or press.

Before placing in the freezer, each

package should be clearly labelled

with the contents and date of freezing.

Maximum freezing

capacity

Foodstuffs should be frozen right through

as quickly as possible. Only in this way it

is possible to retain vitamins, nutrients,

appearance and taste. You should therefore

never exceed your appliance's maximum

freezing capacity.

Within 24 h a max 9 kg of food for 60 cm

width appliances, can

be frozen at once in the

upper compartments.

Food that is already frozen should never

come into contact with fresh food about

to be frozen.

Allow hot food and drinks to cool down

to room temperature before placing in the

freezer.

Freezing and storing

Super cooling

If you are going to buy fresh food you should

switch on super cooling 3-4 hours before or

at the latest when placing fresh food in the

refrigerator. To switch on "super cooling"

simply press the "super cooling" button

(Fig. 2/2). Display "SU" (Fig. 2/4) and the

"Super" display (Fig. 2/5) indicate that

"super cooling" is on. "Super cooling"

reduces the temperature in the refrigerator

compartment for 6 hours. Then the

appliance automatically switches to the

temperature, which was selected prior to

"super cooling"

Fast freezing

If frozen food is already being stored in the

freezer, you should switch on fast freeze

several hours before putting in fresh food

to freeze.

Normally, it will suffice to switch on fast

freeze 4–6 hours ahead. If you are planning

to make full use of maximum freezing

capacity, switch on 24 hours in advance.

Smaller quantities of food (up to 2 kg) can

be frozen without the fast freeze facility. To

switch on "super" freeze, simply press the

"super" freeze button, Fig.

2

/10.

Display "SU" (Fig.

2

/7) and the "Super"

display (Fig.

2

/6) indicate that "super

cooling" is on. After switching on, a very low

temperature is achieved in the freezer

compartment. Fast-freezing switches off

automatically approximately 52 hours after

being switched on.

Storage of food

Make sure that all the frozen goods

containers are pushed in as far as they will go.

This is important so that the air inside the

freezer can circulate properly.

Frozen food calendar

Figure

A

/27

It is important not to exceed maximum

permissible storage times in order to avoid

impairing the quality of the frozen goods.

The actual storage time depends on the type

of food. The numbers next to the symbols

indicate the permissible storage time in

months. In the case of frozen goods

purchased from a shop, observe the

production date or ‘Best before …’ date.

Freezer tray

Fig.

B

The freezer tray is suitable for storing ice

cube trays and for freezing individual berries,

pieces of fruit, herbs and vegetables.

To freeze individual items of food, distribute

the produce uniformly on the freezer tray

and leave to freeze for approx. 10–12 hours.

Then transfer the produce into freezer bags

or containers.

To thaw, spread out the individual items of

food.

Thawing frozen food

Depending on the nature of the food and

the preparation or cooking method you are

going to employ, you may choose one of

the following thawing methods:

at room temperature,

in the refrigerator,

in an electric oven,

fan-assisted or not,

in the microwave oven.

Food that has been partially or completely

defrosted can be refrozen provided that

these items are stored at temperatures

below +3 °C and for no longer than one day

where meat and fish is involved, or no longer

than 3 days for other items.

Otherwise, provided that taste, smell and

appearance remain unchanged, you can

boil, fry or process the food further into

a ready-made dish and then refreeze.

Observe that in this case the admissible

shelf-life will be shorter than normal.

Making ice-cubes

Fig.

<

Fill the ice-cube tray three-quarters full with

water and place it in the freezer.

Twist the tray slightly to remove the ice-cubes.

31

en

30

en

Cleaning

Before cleaning, you should always

unplug the appliance and/or switch off

or disengage the household fuse.

Do not use a steam cleaner. The hot

steam could damage the surface of the

appliance or the electrical components

– electric shock hazard!

Ensure that cleaning water does not get

into the control panel or any of the lights.

Lukewarm water with a little mildly

disinfectant detergent such as washing-up

liquid is ideal for cleaning the entire

appliance, except the door seal. Never use

cleaning agents containing abrasives, acids,

chemical solvents or polishers.

Simply clean the door seal with clear water

and dry thoroughly afterwards.

If possible, the heat exchanger (black grid)

at the back of the appliance should be

cleaned with a brush or vacuum cleaner

every two years. This will maintain the full

efficiency of the appliance and helps to save

electricity.

l Install the appliance in a cool, dry room with

adequate ventilation. Ensure that it is not

exposed to direct sunlight and never put it

near a direct source of heat (radiator, etc.).

l Never block any vents or grilles on the

appliance.

l Allow warm food to cool down before

placing in the appliance.

l Put frozen food in the refrigerator to thaw.

You can then use the low temperatures

of the frozen products to cool food in the

refrigerator.

l Do not keep the door of the appliance

open for too long when loading or taking

out food.

The shorter the time that the door is

opened, the less ice will form on the

freezer grids.

l Clean the heat exchanger (black grid) at

the back of the appliance every two years.

Power saving tips Information about

operating noises

Operating noises

In order to maintain the pre-set temperature

at a constant level, the appliance compressor

switches on from time to time.

The noises that can be heard while it is

running are perfectly normal.

The noise reduces automatically when the

appliance reaches its operating temperature.

The humming noise is emitted by the motor

(compressor). When the motor switches ON,

the noise may briefly increase in volume.

The bubbling, gurgling or whirring noise is

emitted by the refrigerant as it flows through

the pipes.

The clicking noise can always be heard

when the thermostat switches ON/OFF the

motor.

Cracking noises may occur if ...

- the automatic defrosting is operating.

- the appliance is cooling down or

warming up (material expansion).

A multi-zone or No-Frost appliance may

cause a low hissing noise emitted by the

air flow inside the appliance.

If these noises are excessively loud, the

causes are probably not serious and are

usually very easy to eliminate.

The appliance is not level

Please level the appliance with the aid of

a spirit level. Use the height-adjustable feet

or place packing under the feet.

The appliance is not free-standing

Please move the appliance away from

kitchen units or other appliances.

Drawers, baskets or shelves are loose or

stick

Please check the detachable components

and, if required, refit them.

Bottles and/or receptacles are touching

each other

Please move bottles and/or receptacles

away from each other.

*Important information for

the care of stainless steel

surfaces

A trial pack of “Chromol” cleaning agent is

enclosed with the appliance.

TO RETAIN THE HIGH-QUALITY

APPEARANCE OF YOUR APPLIANCE,

TREAT THE STAINLESS STEEL SURFACES

OF THE APPLIANCE IMMEDIATELY AFTER

INSTALLATION WITH THE LIQUID

CLEANING AGENT "CHROMOL". REPEAT

THIS TREATMENT AT REGULAR

INTERVALS.

This cleaning agent is available on the

market under the name “Chromol” or from

your customer service under

Ident. no. 310359 as a 500 ml spray can

To prevent damage to surfaces, under no

circumstances use abrasive sponges, metal

brushes, sharp-edged implements or

scouring agents. Chemically aggressive

cleaning agents, such as defrosting sprays,

oven sprays, solvents or stain removers

must not be used either.

Attention!

Keep out of the reach of children.

Never use on surfaces which come into

contact with food.

Do not use on hot surfaces.

Contains aliphatic hydrocarbons, oils and

aromatic compounds.

* not on all models

33

en

Customer Service

Rating plate

Figure

D

When you call Customer Service you will be

asked for the ‘E’ number and ‘FD’ number

for your appliance.

Both numbers are shown in a box with

a black border on the rating plate. This is

located inside the fridge section, at the

bottom left-hand side next to the vegetable

container.

The address and telephone number of your

nearest Customer Service is listed in the

customer service directory or else in any

telephone directory.

32

en

After pressing the "alarm" button, the

warmest temperature which has prevailed in

the freezer compartment is displayed for

5 seconds on display 7 (not flashing).

Afterward, this value is cancelled.

Display 7 then indicates the selected

temperature without flashing.

If flavour, odour and appearance have

changed, make a ready-made meal out of

the food and refreeze.

No longer store the frozen produce for the

max. storage period.

If "AL" (Fig. 2/7) flashes and the warning

signal is emitted after the freezer

compartment has been running for a

prolonged period :

Fault, freezer compartment is too warm !

To switch off the warning signal, press the

"Alarm" Off button 11 .

The warmest temperature reached is then

displayed.

Possible causes of the fault:

– The clearance at the top of the appliance

or in the base is blocked,

– The freezer-compartment door has not

been closed correctly,

– Fresh food was frozen without Fast freeze,

– Too much fresh food was frozen at once,

– High ambient temperature.

When the fault has been rectified, press the

"Alarm" Off button 11

;

"AL" stops

flashing. The selected temperature is

displayed as soon as the freezer

compartment has reached the selected

temperature.

If the freezer section door has been kept

open for a long time and the temperature

inside now no longer reaches the pre-set

level,

so much ice has formed on the evaporator

(source of cold temperature) that it cannot

be defrosted by the fully automatic

defrosting system. In this case take the

frozen goods out of the freezer, wrap them

well to keep them cold and store them

somewhere cool.

Minor problems and how to rectify them yourself

Switch off the appliance and open the

freezer section door. After about 12 hours

the ice on the cooling system will have

thawed. Switch the appliance on again and

put the frozen goods back inside.

If you are not able to rectify the problem

with the help of the suggestions listed here,

please call Customer Service.

Do not open the door more often than

necessary, so that the cold temperature

inside is retained for as long as possible.

Do not take any further action, especially

with regard to the electrical parts of the

appliance.

Minor problems and how

to rectify them yourself

Customer service should NOT be

contacted for every fault. Most faults

are minor. Therefore, before you call

customer service, please check whether

you can eliminate the fault yourself based

on the following information.

A technician who is called out to rectify

a minor fault will charge the customer, even

if the appliance is still under guarantee.

If the display, Fig.

2

/4-7, does not

illuminate:

check that the power is ON, that the plug is

correctly inserted in the socket and that the

appliance is switched ON.

If "E1" (flashing), Fig.

2

/4, is displayed

while starting the appliance:

A high temperature prevails in the

refrigerator compartment. Several minutes

after the appliance is switched on, the

selected temperature is displayed.

If "E2" (flashing), Fig.

2

/7, is displayed

while starting the appliance:

A high temperature prevails in the freezer

compartment. Several minutes after the

appliance is switched on, "AL" is displayed.

The selected temperature is indicated on

display 7 as soon as the freezer

compartment has reached the selected

temperature.

If the refrigerator-compartment light does

not function:

– The light bulb is defective. Pull out

the mains plug and remove the cover

(Fig.

C

/A). Replace the defective light bulb

with a light bulb of the same type

(max. 15 W, 230 V, E14 holder).

– The light switch is sticking. Check whether

it can be moved (Fig.

C

/B). If not, please

call customer service.

If the display, Fig.

2

/7, flashes but the

acoustic signal is not emitted:

the freezer compartment was too warm due

to a power failure or a fault.

Page is loading ...

Bosch kgs 46123 ff Owner's manual

Bosch kgs 46123 ff Owner's manual

in other languages

Related papers

Other documents