Unbranded 0895900210 Operating instructions

Unbranded
Brand
Unbranded
Model
0895900210
Type
Operating instructions
MADE IN BRAZIL
16 02 04 12
IF PARTS ARE MISSING, PLEASE CALL 1-800-998-7021 FOR INFORMATION.
45 Min.
HAWTHORNE VANITY SLATTED WITH
MIRROR 32”H x 44”W
SKU # 0895900130 – DARK CHERRY
SKU # 0895900560 – OAK
SKU # 0895900410 – WHITE
SKU # 0895900210 – BLACK
BEFORE BEGINNING ASSEMBLY, CHECK TO MAKE SURE ALL
PARTS AND HARDWARE ARE ACCOUNTED FOR.
IT IS SUGGESTED THAT YOU SAVE THE CARTON AND PACKING
MATERIAL UNTIL AFTER ASSEMBLY IS COMPLETED. SELECT A CLEAN,
SMOOTH SURFACE TO WORK (SUCH AS CARPET).
THEN, FOLLOW THE EASY STEPS BELOW.
PART #
QTY
DESCRIPTION SIZES (w x d x h)
1
1
HINGED CENTER TOP 183/4” x 20” x 3/4”
2
1
RIGHT TOP 121/2” x 20” x 3/4”
3
1
LEFT TOP 121/2” x 20” x 3/4”
4
1
RIGHT SIDE 311/4” x 173/4” x 11/4”
5
1
LEFT SIDE
6
4
UPPER FRONT SUPPORT 91/2” x 21/2” x 3/4”
7
1
RIGHT DIVIDER 161/2” x 7” x 3/4”
8
9
10
11
12
13
14
15
16
17
1
1
1
1
1
2
2
2
2
2
LEFT DIVISION
CENTER FRONT
CENTER BOTTOM
BACK PANEL
LOWER CROSS SUPPORT
DRAWER FRONT
RIGHT DRAWER SIDE
LEFT DRAWER SIDE
DRAWER BOTTOM
DRAWER BACK
19” x 5” x 3/4”
193/8” x 161/3” x 1/4”
391/4” x 7” x 3/4”
391/4” x 21/2” x 3/4”
91/4” x 51/3” x 3/4”
121/4” x 43/4” x 1/2”
121/3” x 81/2” x 1/8”
8” x 43/4” x 1/2”
311/4” x 173/4” x 11/4”
161/2” x 7” x 3/4”
121/4” x 43/4” x 1/2”
1
2
3
6
6
6
6
8
10
9
11
7
4
5
12
13
15
17
14
16
B
F
E
D
C
3,5x30 (1 1/4")
3,0x12 (1/2")
4,0x30mm (1 1/4")
4,0x35 (1 3/8")
4,0x25 (1')
A
8x30mm (1 1/4")
22
H
12
2
14
4
J
I
60N
Kit
48
G
4
2
4
2
STEP 1
A
H
H
4
5
12
7
8
9
11
6
4x
15
2x
14
2x
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
H
H
H
Insert wooden dowels (A) into the predrilled holes in parts 4, 5 6, 7, 8, 9, 11, 12, 14
and 15 as shown in the diagram. Insert and screw the metal guide supports (H)
into right divider(7) and left divider(8).
STEP 4
+
-
12
6
4
5
6
6
6
B
B
B
B
B
With center compartment laying on its back (11)
as shown in diagram, attach the front cross supports (6),
back panel (11) and bottom cross support(12) so that
the sides(4 & 5) and center compartment are
aligned and attached to one another with the
dowels. Secure the front cross supports
(6) using the pocket screws (B).
STEP 2 STEP 3
C
C
C
C
C
C
9
8
7
10
11
C
C
Insert center front (9) into right (7) and left (8)
sides and screw together using screws (C).
Insert vanity center bottom (10) by sliding panel into
pre-routed grooves as shown in the diagram. Attach back
(11) to center compartment using the dowels as your guide.
Secure with screws (C) as shown in diagram.
C
C
STEP 6
2x
This construction is for 2 drawers: Screw drawer sides (14 & 15) to drawer front (13)
using pocket screws (B). Slide drawer bottom (16) into pre-routed groove to the
bottom of the drawer assembly. Attach drawer back (17) to the drawer assembly
using screws (E). Attach drawer catch (J) using screw (F). Attach drawer knob ( I )
to front of drawers using screw (E).
F
J
I
14
15
16
17
B
B
B
B
B
E
E
E
E
E
F
J
C
STEP 5
3
2
C
C
C
B
B
D
D
B
B
C
C
D
B
C
C
1
Lay the three tops ( 1, 2 & 3 ) as shown in diagram upside down on soft surface.
Turn base over to align holes on the vanity and tops with the dowels and secure
together using pocket screws (B and C) as shown in diagram. Assure alignment
is made with the metal pine and secure with screws (D) as shown.
13
STEP 7
Once vanity has been turned right side up and drawers have been inserted it is time
to attach the hinges (G). Attach the hinge to that it is positioned to the left hand side
of the vanity as shown with hinge folding up. Using screws (G) attached the hinge
using the predrilled holes on the vanity top and center. Attach the knobs (I) to the
center section of the vanity using screws (E).
E
90º
G
G
G
Kit
60N
Kit
60N
G
G
G
G
E
I
I
STEP 8
Instructions
Tipping restraint
A
WALLBOARDWALLBOARDWALLBOARD
WALLBOARDWALLBOARDWALLBOARD
Set in furniture
Set in Wall
A 1
B
C
D
E
2
2
2
2
Nylon strap
1 ½” screw
6mm Plastic screw anchor
Plastic wall bracket
Small screw
TIPPING RESTRAINT
HARDWARE
• When properly installed, this hardware can provide
protection against the unexpected tipping of furniture.
• Attach one of the mounting brackets “D” securely to
the back top edge of the unit using the short screw “E”.
• Mark the location on the wall for mounting the second bracket "D".
Drill the appropriate sized hole in the wall and insert the plastic screw anchor "C".
Then secure the bracket to the wall using screw "B".
• Place the unit so the bracket on the back edge of unit is in line with the bracket
on the wall.
• Lace the end of the nylon restraint strap “A” through each bracket.
Bring both ends together and slide the beaded end of the strap through
the keyhole shaped slot on the other end.
Pull down on the beaded end until it snap-locks into the keyhole.
• Check to make sure the strap is securely laced and locked to the brackets.
E
E
B
B
C
D
D
C
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7

Unbranded 0895900210 Operating instructions

Unbranded
Brand
Unbranded
Model
0895900210
Type
Operating instructions
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents