BLACK DECKER BDBBC2C Owner's manual

Page is loading ...

2

ENGLISH

English

Intended use

Your Black & Decker ‘Car to Car Simple Start’ is designed to

boost a depleted battery on a host vehicle from a donor

vehicle.

Note: This unit will not start a flat battery.

Safety instructions

Warning! When using battery-powered appliances, basic

safety precautions, including the following, should always be

followed to reduce the risk of fire, electric shock, personal

injury and material damage.

X Read all of this manual carefully before using the

appliance.

X The intended use is described in this manual. The use

of any accessory or attachment or the performance of

any operation with this appliance other than those

recommended in this instruction manual may present a

risk of personal injury.

X Retain this manual for future reference.

Using your appliance

Always take care when using the appliance.

X This appliance is not intended for use by young or in firm

persons without supervision.

X The appliance is not to be used as a toy.

X Use in a dry location only. Do not allow the appliance to

become wet.

X Do not immerse the appliance in water.

X Do not open body casing. There are no user serviceable

parts inside.

X Do not operate the appliance in explosive atmospheres,

such as in the presence of flammable liquids, gases or

dust.

X To reduce the risk of damage to plugs and cords never

pull the cable to remove the plug from a socket outlet.

After use

X When not in use, the appliance should be stored in a

dry, well ventilated place out of the reach of children.

X Children should not have access to stored appliances.

X When the appliance is stored or transported in a vehicle

it should be placed in the boot or restrained to prevent

movement following sudden changes in speed or

direction.

X The appliance should be protected from direct sunlight,

heat and moisture.

Inspection and repairs

X Before use, check the appliance for damaged or

defective parts. Check for breakage of parts, damage to

switches and any other conditions that may affect its

operation.

X Do not use the appliance if any part is damaged or

defective.

X Have any damaged or defective parts repaired or

replaced by an authorised repair agent.

X Never attempt to remove or replace any parts other than

those specified in this manual.

Specific safety instructions for battery chargers

Read these instructions before use:

X If the supply cord is damaged, it must be replaced by the

manufacturer or an authorised Black & Decker Service

Centre in order to avoid a hazard.

X Never attempt to charge non-rechargeable batteries.

X Have defective cords replaced immediately.

X Do not expose the battery charger to water.

X Do not open the battery charger.

X Do not probe the battery charger.

Batteries

Warning! Never attempt to charge a frozen battery.

X Never attempt to open for any reason.

X Do not expose the battery to water.

Warning! Battery fluid is a diluted sulphuric acid and may

cause personal injury or damage to property. In case of skin

contact, immediately rinse with water. If redness, pain or

irritation occurs seek medical attention. In case of eye

contact, rinse immediately with clean water and seek

immediate medical attention.

When disposing of batteries, follow the instructions given in

the section ‘Protecting the environment’.

Warning! Risk of explosive gas mixtures. Working in the

vicinity of a lead-acid battery is dangerous. Batteries

generate explosive gases during normal battery operation.

For this reason, it is of utmost importance that each time, you

read this manual and follow the instructions exactly.

Use of an attachment not recommended or sold by Black &

Decker may result in a risk of fire, electric shock, or injury to

persons.

Warning! A marine (boat) battery must be removed and

charged on shore. To charge it on board requires equipment

specially designed for marine use. This appliance is NOT

designed for such use.

X Vehicles may have electrical and electronic systems

(e.g. engine management system, mobile phone) that

may be damaged if subjected to high starting voltages

and voltage peaks. Before connecting the appliance to

the vehicle read the vehicle's owner's manual to confirm

that external-starting assistance is allowed.

3

ENGLISH

X Follow these instructions and those published by the

battery manufacturer, vehicle manufacturer and

manufacturer of any equipment you intend to use with

this unit. Review warning labels on these products and

on the vehicle.

X This appliance is not designed to be used as a

replacement for a vehicular battery. Do not attempt to

operate a vehicle that does not have a battery installed.

X The appliance must only be connected to a 12 V lead-

acid battery. Do not use the appliance for charging dry-

cell batteries that are commonly used with home

appliances. These batteries may burst and cause injury

to persons and damage property.

Warning! Explosive gas may be vented from the lead-acid

batteries when charging and under extreme conditions

battery leakage may occur. Make sure that the area is well

ventilated when conducting jump starting and charging

procedures.

The following symbols are marked on the appliance:

Features

1. Power LED indicator

2. Boosting LED indicator

3. Plug storage

4. Cord storage

5. 12 Vdc accessory plugs

6. Housing

Use

Warning! Make sure that the car is in neutral and the parking

brake is applied.

Step 1

X Connect the black 12 Vdc accessory plug (5) into the

12 V outlet on the working vehicle and make sure that

the power LED (1) lights.

X Start the engine on the working vehicle.

Step 2

Warning! Make sure that car is in neutral and the parking

brake is applied.

X Fully unwind the cord from the cord storage (4) and

connect the orange 12 Vdc accessory plug (5) into the

12 V outlet on the dead vehicle and make sure that the

boosting LED (2) lights.

Step 3

X When the dead car is sufficiently boosted to start the

engine both the power LED (1) and the boosting LED (2)

will change colour to green (approx. 20 minutes).

X Remove the orange 12 Vdc accessory plug (5) from the

dead car and try starting the vehicle in 3-5 second

bursts.

Note: The housing (6) and the 12 Vdc accessory plugs (5)

will become warm during the boosting process. This is

normal.

Step 4

X Remove the black 12 Vdc accessory plug (5) from the

working car and coil the cable around the cord storage

(4) and fit the 12 Vdc accessory plugs (5) into the plug

storage apertures (3).

Maintenance

Your Black & Decker tool has been designed to operate over

a long period of time with a minimum of maintenance.

Continuous satisfactory operation depends upon proper

care and regular cleaning.

Warning! Before performing any maintenance or cleaning

on the appliance, unplug the appliance.

X From time to time wipe the appliance with a damp cloth.

Do not use any abrasive or solvent-based cleaner. Do

not immerse the appliance in water.

X Clean the outside case with a soft cloth and, if

necessary, mild soap solution.

X Do not allow liquid to enter the unit. Do not operate

when the unit is wet.

X Keep the cords coiled during storage to prevent damage

to the cords.

Troubleshooting

If the power and boosting LED’s (1 & 2) do not light up check

the following:

X Check that the donor vehicles 12 V accessory socket is

live, some cars require the key to be in the accessory

position before the socket is live.

X Check that the 12 Vdc accessory plugs (5) are fully

inserted.

X Check for blown fuses in the 12 Vdc accessory

plugs (5).

If your car fails to start:

X Repeat steps 2-4 in the ‘use’ section and continue the

boosting process for a further 10 minutes or until the

LED’s change to green.

X If your car still fails to start we suggest you have your

battery checked by a qualified auto-electrician.

Power LED indicator.

Boosting LED indicator.

4

ENGLISH

Replacing the fuse in the vehicle dc accessory plug

X Remove the cap by turning it counter clockwise.

X Remove the cap and centre pin.

X Remove the fuse.

X Fit a new fuse of the same type and size (8 A).

X Refit the cap and centre pin.

X Tighten the cap by turning clockwise onto the plug.

Protecting the environment

Should you find one day that your Black & Decker product

needs replacement, or if it is of no further use to you, do not

dispose of it with household waste. Make this product

available for separate collection.

Separate collection of used products and packaging

allows materials to be recycled and used again. Re-

use of recycled materials helps prevent

environmental pollution and reduces the demand

for raw materials.

Local regulations may provide for separate collection of

electrical products from the household, at municipal waste

sites or by the retailer when you purchase a new product.

Black & Decker provides a facility for the collection and

recycling of Black & Decker products once they have

reached the end of their working life. To take advantage of

this service please return your product to any authorised

repair agent who will collect them on our behalf.

You can check the location of your nearest authorised repair

agent by contacting your local Black & Decker office at the

address indicated in this manual. Alternatively, a list of

authorised Black & Decker repair agents and full details of

our after-sales service and contacts are available on the

Internet at: www.2helpU.com.

Technical data

EC declaration of conformity

BDBBC2C TYPE 1

Black & Decker declares that these products conform to:

EN60335, EN60598

The undersigned is responsible for compilation of the

technical file and makes this declaration on behalf of

Black & Decker

Kevin Hewitt

Director of Consumer Engineering

Spennymoor, County Durham, DL16 6JG,

United Kingdom

12-08-2008

Guarantee

Black & Decker is confident of the quality of its products and

offers an outstanding guarantee. This guarantee statement

is in addition to and in no way prejudices your statutory

rights. The guarantee is valid within the territories of the

Member States of the European Union and the European

Free Trade Area.

If a Black & Decker product becomes defective due to faulty

materials, workmanship or lack of conformity, within 24

months from the date of purchase, Black & Decker

guarantees to replace defective parts, repair products

subjected to fair wear and tear or replace such products to

make sure of the minimum inconvenience to the customer

unless:

X The product has been used for trade, professional or

hire purposes.

X The product has been subjected to misuse or neglect.

X The product has sustained damage through foreign

objects, substances or accidents.

X Repairs have been attempted by persons other than

authorised repair agents or Black & Decker service

staff.

To claim on the guarantee, you will need to submit proof of

purchase to the seller or an authorised repair agent. You can

check the location of your nearest authorised repair agent by

contacting your local Black & Decker office at the address

indicated in this manual. Alternatively, a list of authorised

Black & Decker repair agents and full details of our after-

sales service and contacts are available on the Internet at:

www.2helpU.com

Please visit our website www.blackanddecker.co.uk to

register your new Black & Decker product and to be kept up

to date on new products and special offers. Further

information on the Black & Decker brand and our range of

products is available at www.blackanddecker.co.uk.

Separate collection. This product must not be

disposed of with normal household waste.

BDBBC2C

Input voltage Vdc 12

Output voltage Vdc 14.5

Output current (max) A 7.5

Weight kg 1.93

Page is loading ...

BLACK DECKER BDBBC2C, BDBBC2C T1 Owner's manual

Related papers

Other documents