Yamaha F115 Owner's manual

F115

LF115

OWNER’S MANUAL

68V-28199-18

U.S.A.Edition

LIT-18626-07-13

EMU25060

ZMU01690

Read this owner’s manual carefully before operating your outboard motor.

Important manual information

EMU31280

To the owner

Thank you for choosing a Yamaha outboard

motor. This Owner’s Manual contains infor-

mation needed for proper operation, mainte-

nance and care. A thorough understanding

of these simple instructions will help you ob-

tain maximum enjoyment from your new

Yamaha. If you have any question about the

operation or maintenance of your outboard

motor, please consult a Yamaha dealer.

In this Owner’s Manual particularly important

information is distinguished in the following

ways.

The Safety Alert Symbol means

ATTENTION! BECOME ALERT! YOUR

SAFETY IS INVOLVED!

WARNING

EWM00780

Failure to follow WARNING instructions

could result in severe injury or death

to

the machine operator, a bystander, or a

person inspecting or repairing the out-

board motor.

CAUTION:

ECM00700

A CAUTION indicates special precautions

that must be taken to avoid damage to the

outboard motor.

NOTE:

A NOTE provides key information to make

procedures easier or clearer.

Yamaha continually seeks advancements in

product design and quality. Therefore, while

this manual contains the most current prod-

uct information available at the time of print-

ing, there may be minor discrepancies

between your machine and this manual. If

there is any question concerning this manu-

al, please consult your Yamaha dealer.

NOTE:

The F115TR, LF115TR and the standard ac-

cessories are used as a base for the expla-

nations and illustrations in this manual.

Therefore some items may not apply to ev-

ery model.

EMU25110

F115, LF115

OWNER’S MANUAL

1st edition, March 2006

Any reprinting or unauthorized use

without the written permission of

Yamaha Motor Corporation, USA

is expressly prohibited.

Printed in Japan

P/N LIT-18626-07-13

Table of contents

General information .......................... 1

Identification numbers record.......... 1

Outboard motor serial number .......... 1

Key number....................................... 1

Emission control information ........... 1

North American models..................... 1

Star labels ......................................... 2

Safety information ........................... 3

Important labels............................... 4

Warning labels .................................. 4

Basic boating rules (Rules of the

road) .............................................. 5

Steering and sailing rules and

sound signals.................................. 5

Rules when encountering vessels .... 5

Other special situations..................... 6

Fueling instructions ......................... 8

Gasoline............................................ 9

Engine oil .......................................... 9

Battery requirement....................... 10

Battery specifications ...................... 10

Propeller selection......................... 10

Start-in-gear protection ................. 11

Basic components .......................... 12

Main components.......................... 12

Remote control................................ 13

Remote control lever....................... 14

Neutral interlock trigger................... 14

Neutral throttle lever........................ 14

Free accelerator.............................. 15

Tiller handle .................................... 15

Gear shift lever................................ 15

Throttle grip..................................... 16

Throttle indicator ............................. 16

Throttle friction adjuster................... 16

Engine stop lanyard switch ............. 17

Engine stop button .......................... 18

Main switch ..................................... 18

Steering friction adjuster ................. 18

Power trim and tilt switch on remote

control or tiller handle ................... 19

Power trim and tilt switch on bottom

engine cowling .............................. 19

Power trim and tilt switches (twin

binnacle type) ............................... 20

Trim tab with anode.........................20

Tilt support lever for power trim and

tilt or hydro tilt model.....................21

Top cowling lock lever

(pull up type) ................................. 21

Flushing device ...............................22

Water separator ..............................22

Tachometer ..................................... 22

Digital tachometer ...........................22

Low oil pressure warning

indicator ........................................23

Low oil pressure warning

indicator ........................................23

Overheat warning indicator .............24

Overheat warning indicator (digital

type) .............................................. 24

Speedometer (digital type) .............. 24

Trim meter....................................... 25

Trim meter (digital type) ..................25

Hour meter (digital type)..................25

Trip meter........................................ 26

Clock ...............................................26

Fuel gauge ...................................... 26

Fuel warning indicator ..................... 27

Low battery voltage warning

indicator ........................................27

Fuel management meter ................. 27

Fuel flow meter................................28

Fuel consumption meter..................28

Fuel economy..................................28

Twin-engine speed synchronizer ....29

Command link multifunction

meters ........................................... 30

Tachometer unit ..............................30

Speed & fuel meter unit...................33

Speedometer unit............................ 34

Fuel management meter ................. 35

Warning system ............................ 36

Overheat warning (twin engines) ....36

Low oil pressure warning ................37

Operation ......................................... 38

Installation..................................... 38

Mounting the outboard motor .......... 38

Breaking in engine ........................ 39

Procedure for 4-stroke models........ 39

Table of contents

Preoperation checks ..................... 40

Fuel ................................................. 40

Controls........................................... 40

Engine............................................. 40

Checking the engine oil level .......... 40

Filling fuel ...................................... 41

Ring Free Fuel Additive .................. 41

Operating engine........................... 41

Feeding fuel .................................... 41

Starting engine................................ 42

Warming up engine ....................... 45

Manual start and electric start

models .......................................... 45

Shifting .......................................... 45

Forward (tiller handle and remote

control models) ............................. 45

Reverse (automatic reverse lock

and power trim and tilt models)..... 46

Stopping engine ............................ 47

Procedure ....................................... 47

Trimming outboard motor.............. 48

Adjusting trim angle ........................ 48

Adjusting boat trim .......................... 49

Tilting up and down ....................... 50

Procedure for tilting up (power trim

and tilt models / power tilt

models) ......................................... 51

Procedure for tilting down (power

trim and tilt models / power tilt

models) ......................................... 52

Cruising in shallow water .............. 53

Power trim and tilt models / power

tilt models...................................... 53

Cruising in other conditions........... 54

Maintenance..................................... 56

Specifications ................................ 56

Transporting and storing outboard

motor ........................................... 57

Storing outboard motor ................... 57

Procedure ....................................... 58

Lubrication ...................................... 59

Cleaning and anticorrosion

measures ...................................... 59

Battery care..................................... 59

Flushing power unit......................... 60

Cleaning the outboard motor...........61

Checking painted surface of

motor.............................................61

Periodic maintenance ................... 61

Replacement parts .......................... 61

Maintenance chart...........................62

Maintenance chart (additional)........ 63

Greasing..........................................64

Cleaning and adjusting spark

plug ............................................... 64

Checking fuel system ...................... 65

Inspecting idling speed....................66

Changing engine oil ........................66

Checking wiring and connectors .....68

Exhaust leakage..............................68

Water leakage ................................. 68

Engine oil leakage........................... 68

Checking power trim and tilt

system...........................................68

Checking propeller ..........................69

Removing the propeller ................... 70

Installing the Propeller.....................70

Changing gear oil ............................ 71

Inspecting and replacing

anode(s)........................................72

Checking battery (for electric start

models) ......................................... 73

Connecting the battery .................... 73

Disconnecting the battery................74

Checking top cowling ......................74

Coating the boat bottom.................. 74

Trouble Recovery............................ 75

Troubleshooting ............................ 75

Temporary action in emergency ... 78

Impact damage ...............................78

Running single engine.....................78

Replacing fuse ................................79

Power trim and tilt / power tilt will

not operate....................................79

Water separator warning indicator

blinks while cruising ...................... 80

Starter will not operate ....................81

Emergency starting engine .............82

Treatment of submerged motor .... 83

Procedure........................................83

Table of contents

Consumer information.................... 84

Important warranty information for

U.S.A. and Canada ..................... 84

YAMAHA MOTOR

CORPORATION, U.S.A.

FOUR-STROKE OUTBOARD

MOTOR

THREE-YEAR LIMITED

WARRANTY ................................ 86

IMPORTANT WARRANTY

INFORMATION IF YOU USE

YOUR YAMAHA OUTSIDE THE

USA OR CANADA ...................... 88

1

General information

EMU25170

Identification numbers record

EMU25183

Outboard motor serial number

The outboard motor serial number is

stamped on the label attached to the port

side of the clamp bracket.

Record your outboard motor serial number in

the spaces provided to assist you in ordering

spare parts from your Yamaha dealer or for

reference in case your outboard motor is sto-

len.

EMU25190

Key number

If a main key switch is equipped with the mo-

tor, the key identification number is stamped

on your key as shown in the illustration.

Record this number in the space provided for

reference in case you need a new key.

EMU25221

Emission control information

EMU25230

North American models

This engine conforms to U.S. Environmental

Protection Agency (EPA) regulations for ma-

rine SI engines. See the label affixed to your

engine for details.

EMU31560

Approval label of emission control certif-

icate

This label is attached to the bottom cowling.

New Technology; (4-stroke) MFI

1. Outboard motor serial number location

1. Key number

1. Approval label location

ZMU04276

1

General information

2

EMU25262

Manufactured date label

This label is attached to the clamp bracket or

the swivel bracket.

EMU25272

Star labels

Your outboard motor is labeled with a Cali-

fornia Air Resources Board (CARB) star la-

bel. See below for a description of your

particular label.

EMU25280

One Star—Low Emission

The one-star label identifies engines that

meet the Air Resources Board’s 2001 ex-

haust emission standards. Engines meeting

these standards have 75% lower emissions

than conventional carbureted two-stroke en-

gines. These engines are equivalent to the

U.S. EPA’s 2006 standards for marine en-

gines.

EMU25290

Two Stars—Very Low Emission

The two-star label identifies engines that

meet the Air Resources Board’s 2004 ex-

haust emission standards. Engines meeting

these standards have 20% lower emissions

than One Star-Low-Emission engines.

1. Manufactured date label location

ZMU04277

1

ZMU04776

ZMU01702

General information

3

EMU25300

Three Stars—Ultra Low Emission

The three-star label identifies engines that

meet the Air Resources Board’s 2008 ex-

haust emission standards. Engines meeting

these standards have 65% lower emissions

than One Star-Low-Emission engines.

EMU25362

Safety information

●

Before mounting or operating the outboard

motor, read this entire manual. Reading it

should give you an understanding of the

motor and its operation.

●

Before operating the boat, read any own-

er’s or operator’s manuals supplied with it

and all labels. Be sure you understand

each item before operating.

●

Do not overpower the boat with this out-

board motor. Overpowering the boat could

result in loss of control. The rated power of

the outboard should be equal to or less

than the rated horsepower capacity of the

boat. If the rated horsepower capacity of

the boat is unknown, consult the dealer or

boat manufacturer.

●

Do not modify the outboard. Modifications

could make the motor unfit or unsafe to

use.

●

Incorrect propeller selection and incorrect

use may not only cause engine damage,

but also adversely affect fuel consumption.

Consult your dealer for correct use.

●

Never operate after drinking alcohol or tak-

ing drugs. About 50% of all boating fatali-

ties involve intoxication.

●

Have an approved personal flotation de-

vice (PFD) on board for every occupant. It

is a good idea to wear a PFD whenever

boating. At a minimum, children and non-

swimmers should always wear PFDs, and

everyone should wear PFDs when there

are potentially hazardous boating condi-

tions.

●

Gasoline is highly flammable, and its va-

pors are flammable and explosive. Handle

and store gasoline carefully. Make sure

there are no gas fumes or leaking fuel be-

fore starting the engine.

●

This product emits exhaust gases which

contain carbon monoxide, a colorless,

odorless gas which may cause brain dam-

age or death when inhaled. Symptoms in-

clude nausea, dizziness, and drowsiness.

Keep cockpit and cabin areas well ventilat-

ed. Avoid blocking exhaust outlets.

●

Check throttle, shift, and steering for prop-

er operation before starting the engine.

●

Attach the engine stop switch lanyard cord

to a secure place on your clothing, or your

arm or leg while operating. If you acciden-

tally leave the helm, the cord will pull from

ZMU01703

ZMU01704

General information

4

the switch, stopping the engine.

●

Know the marine laws and regulations

where you will be boating—and obey

them. For basic boating rules, see “Rules

of the road” on page 5.

●

Stay informed about the weather. Check

weather forecasts before boating. Avoid

boating in hazardous weather.

●

Tell someone where you are going: leave

a Float Plan with a responsible person. Be

sure to cancel the Float Plan when you re-

turn.

●

Use common sense and good judgment

when boating. Know your abilities, and be

sure you understand how your boat han-

dles under the different boating conditions

you may encounter. Operate within your

limits, and the limits of your boat. Always

operate at safe speeds, and keep a careful

watch for obstacles and other traffic.

●

Always watch carefully for swimmers dur-

ing the engine operation.

●

Stay away from swimming areas.

●

When a swimmer is in the water near you

shift into neutral and shut off the engine.

●

Do not illegally discard empty containers

used to replace or replenish oil. For the

correct processing of empty containers,

consult the dealer where you purchased

the oil.

●

When replacing oils used to lubricate the

product (engine or gear oil), be sure to

wipe away any spilt oil. Never pour oil with-

out using a funnel or similar device. If nec-

essary, verify the necessary replacement

procedure with the dealer.

●

Never illegally discard (dump) the product.

Yamaha recommends consulting the deal-

er on discarding the product.

Be informed about boating safety. Additional

publications and information can be obtained

from many organizations, including the fol-

lowing:

United States Coast Guard

Consumer Affairs Staff (G-BC)

Office of Boating, Public, and Consumer Af-

fairs

U.S. Coast Guard Headquarters

Washington, D.C. 20593-0001

Boating Safety Hotline: 1-800-368-5647

National Marine Manufacturers Associa-

tion (NMMA)

401 N. Michigan Ave.

Chicago, Il 60611

Marine Retailers Association of America

155 N. Michigan Ave.

Chicago, Il 60601

EMU25382

Important labels

EMU25395

Warning labels

EMU25401

Label

WARNING

EWM01260

●

Be sure shift control is in neutral before

starting engine. (except 2HP)

●

Do not touch or remove electrical parts

when starting or during operation.

●

Keep hands, hair, and clothes away

from flywheel and other rotating parts

while engine is running.

ZMU04275

General information

5

EMU25413

Label (counter rotation models)

WARNING

EWM01281

Use only a counterclockwise rotation

propeller with this engine.

Counterclockwise propellers are marked

with a letter “L” after the size indication.

The wrong type of propeller could cause

the boat to go in an unexpected direction,

which could lead to an accident.

EMU25500

Basic boating rules (Rules of

the road)

Just as there are rules which apply when you

are driving on streets and high ways, there

are waterway rules which apply when you

are driving your boat. These rules are used

internationally, and are also enforced by the

United States Coast Guard and local agen-

cies. You should be aware of these rules,

and follow them whenever you encounter

another vessel on the water.

Several sets of rules prevail according to

geographic location, but are all basically the

same as the International Rules of the Road.

The rules presented here in your Owner’s

Manual are condensed, and have been pro-

vided for your convenience only. Consult

your local U.S. Coast Guard Auxiliary or De-

partment of Motor Vehicles for a complete

set of rules governing the waters in which

you will be using your boat.

EMU25510

Steering and sailing rules and sound

signals

Whenever two vessels on the water meet

one another, one vessel has the right-of-

way; it is called the “stand-on” vessel. The

vessel which does not have the right-of-way

is called the “give-way” or “burdened” vessel.

These rules determine which vessel has the

right-of-way, and what each vessel should

do.

Stand-on vessel

The vessel with the right-of-way has the duty

to continue its course and speed, except to

avoid an immediate collision. When you

maintain your direction and speed, the other

vessel will be able to determine how best to

avoid you.

Give-way vessel

The vessel which does not have the right-of-

way has the duty to take positive and timely

action to stay out of the way of the Stand-On

vessel. Normally, you should not cross in

front of the vessel with the right-of-way. You

should slow down or change directions brief-

ly and pass behind the other vessel. You

should always move in such a way that the

operator of the other vessel can see what

you are doing.

“The general prudential rule”

This rule is called Rule 2 in the International

Rules and says,

“In obeying and construing these rules due

regard shall be had to all dangers of naviga-

tion and collision, and to any special circum-

stances, which may render a departure from

the above rules necessary in order to avoid

immediate danger.”

In other words, follow the standard rules ex-

cept when a collision will occur unless both

vessels try to avoid each other. If that is the

case, both vessels become “Give-Way” ves-

sels.

EMU25520

Rules when encountering vessels

There are three main situations which you

may encounter with other vessels which

could lead to a collision unless the Steering

Rules are followed:

Meeting:

(you are approaching another ves-

General information

6

sel head-on)

Crossing:

(you are traveling across the oth-

er vessel’s path)

Overtaking:

(you are passing or being

passed by another vessel)

In the following illustration, your boat is in the

center. You should give the right-of-way to

any vessels shown in white area (you are the

Give-Way vessel). Any vessels in the shad-

ed area must yield to you (they are the Give-

Way vessels). Both you and the meeting

vessel must alter course to avoid each other.

Meeting

If you are meeting another power vessel

head on, and are close enough to run the risk

of collision, neither of you has the right-of-

way! Both of you should alter course to avoid

an accident. You should keep the other ves-

sel on your port (left) side. This rule doesn’t

apply if both of you will clear one another if

you continue on your set course and speed.

Crossing

When two power driven vessels are crossing

each other’s path close enough to run the

risk of collision, the vessel which has the oth-

er on the starboard (right) side must keep out

of the way of the other. If the other vessel is

on your right, you must keep out of its way;

you are the Give-Way vessel. If the other

vessel is on your port (left) side, remember

that you should maintain course and direc-

tion, provided the other vessel gives you the

right-of-way as it should.

Overtaking

If you are passing another vessel, you are

the “Give-Way” vessel. This means that the

other vessel is expected to maintain its

course and speed. You must stay out of its

way until you are clear of it. Likewise, if an-

other vessel is passing you, you should

maintain your speed and direction so that the

other vessel can steer itself around you.

EMU25530

Other special situations

There are three other rules you should be

aware of when driving your boat around oth-

er vessels.

Narrow channels and bends

When navigating in narrow channels, you

should keep to the right when it is safe and

practical to do so. If the operator of a power-

driven vessel is preparing to go around a

General information

7

bend that may obstruct the view of other wa-

ter vessels, the operator should sound a pro-

longed blast on the whistle (4 to 6 seconds).

If another vessel is around the bend, it too

should sound the whistle. Even if no reply is

heard, however, the vessel should still pro-

ceed around the bend with caution. If you

navigate such waters with your boat, you will

need to carry a portable air horn, available

from local marine supply stores.

Fishing vessel right-of-way

All vessels which are fishing with nets, lines

or trawls are considered to be “fishing ves-

sels” under the International Rules. Vessels

with trolling lines are not considered fishing

vessels. Fishing vessels have the right-of-

way regardless of position. Fishing vessels

cannot, however, impede the passage of

other vessels in narrow channels.

Sailing vessel right-of-way

Sailing vessels should normally be given the

right-of-way. The exceptions to this are:

1. When the sailing vessel is overtaking

the power-driven vessel, the power-driv-

en vessel has the right-of-way.

2. Sailing vessels should keep clear of any

fishing vessel.

3. In a narrow channel, a sailing vessel

should not hamper the safe passage of

a power-driven vessel which can navi-

gate only in such a channel.

Reading buoys and other markers

The waters of the United states are marked

for safe navigation by the lateral system of

buoyage. Simply put, buoys and markers

have an arrangement of shapes, colors,

numbers and lights to show which side of the

buoy a boater should pass on when navigat-

ing in a particular direction. The markings on

these buoys are oriented from the perspec-

tive of being entered from seaward (the boat-

er is going towards the port). This means that

red buoys are passed on the starboard

(right) side when proceeding from open wa-

ter into port, and black buoys are to port (left)

side. When navigating out of port, your posi-

tion with respect to the buoys should be re-

versed; red buoys should be to port and

black buoys to starboard.

Many bodies of water used by boaters are

entirely within the boundaries of a particular

state. The Uniform State Waterway Marking

System has been devised for these waters.

This system uses buoys and signs with dis-

tinctive shapes and colors to show regulato-

ry or advisory information. These markers

are white with black letters and orange

boarders. They signify speed zones, restrict-

ed areas, danger areas, and general infor-

mation.

Remember, markings may vary by geo-

graphic location. Always consult local boat-

ing authorities before driving your boat in

unfamiliar waters.

General information

8

EMU25540

Fueling instructions

WARNING

EWM00010

GASOLINE AND ITS VAPORS ARE HIGH-

LY FLAMMABLE AND EXPLOSIVE!

●

Do not smoke when refueling, and keep

away from sparks, flames, or other

sources of ignition.

●

Stop engine before refueling.

●

Refuel in a well-ventilated area. Refuel

portable fuel tanks off the boat.

●

Take care not to spill gasoline. If gaso-

line spills, wipe it up immediately with

ZMU01708

General information

9

dry rags.

●

Do not overfill the fuel tank.

●

Tighten the filler cap securely after re-

fueling.

●

If you should swallow some gasoline,

inhale a lot of gasoline vapor, or get

gasoline in your eyes, get immediate

medical attention.

●

If any gasoline spills onto your skin, im-

mediately wash with soap and water.

Change clothing if gasoline spills on it.

●

Touch the fuel nozzle to the filler open-

ing or funnel to help prevent electro-

static sparks.

CAUTION:

ECM00010

Use only new clean gasoline which has

been stored in clean containers and is not

contaminated with water or foreign mat-

ter.

EMU25570

Gasoline

If knocking or pinging occurs, use a different

brand of gasoline or premium unleaded fuel.

Gasohol

There are two types of gasohol: gasohol con-

taining ethanol and that containing metha-

nol. Gasohol containing ethanol can be used

if ethanol content does not exceed 10% and

the fuel meets minimum octane ratings.

Yamaha does not recommended gasohol

containing methanol because it can cause

fuel system damage or engine performance

problems.

EMU31440

Engine oil

NOTE:

If the recommended engine oil grades are

not available, select an alternative from the

following chart according to the average

temperatures in your area.

CAUTION:

ECM01050

All 4-stroke engines are shipped from the

factory without engine oil.

Recommended gasoline:

Regular unleaded gasoline with a min-

imum octane rating of 86 (Pump Oc-

tane Number) = (R+M)/2

Recommended engine oil:

YAMALUBE 4-M FC-W oil or 4-stroke

motor oil with a combination of the fol-

lowing SAE and API oil classifications

Engine oil type SAE:

10W-30 or 10W-40

Engine oil grade API:

SE, SF, SG, SH, SJ, SL

Engine oil quantity (excluding oil filter):

4.3 L (4.55 US qt) (3.78 Imp.qt)

General information

10

EMU25700

Battery requirement

CAUTION:

ECM01060

Do not use a battery that does not meet

the specified capacity. If a battery which

does not meet specifications is used, the

electric system could perform poorly or

be overloaded, causing electric system

damage.

For electric start models, choose a battery

which meets the following specifications.

EMU25711

Battery specifications

NOTE:

The engine cannot be started if battery volt-

age is too low.

EMU25742

Propeller selection

The performance of your outboard motor will

be critically affected by your choice of propel-

ler, as an incorrect choice could adversely

affect performance and could also seriously

damage the motor. Engine speed depends

on the propeller size and boat load. If engine

speed is too high or too low for good engine

performance, this will have an adverse effect

on the engine.

Yamaha outboard motors are fitted with pro-

pellers chosen to perform well over a range

of applications, but there may be uses where

a propeller with a different pitch would be

more appropriate. For a greater operating

load, a smaller-pitch propeller is more suit-

able as it enables the correct engine speed

to be maintained. Conversely, a larger-pitch

propeller is more suitable for a smaller oper-

ating load.

Yamaha dealers stock a range of propellers,

and can advise you and install a propeller on

your outboard that is best suited to your ap-

plication.

NOTE:

Select a propeller which will allow the engine

to reach the middle or upper half of the oper-

ating range at full throttle with the maximum

boat load. If operating conditions such as

light boat loads then allow the engine r/min to

Minimum cold cranking amps (CCA/

SAE):

380.0 A

Minimum marine cranking amps (MCA/

ABYC):

502.0 A

Minimum reserve capacity (RC/SAE):

124 minutes

ZMU01710

1. Propeller diameter in inches

2. Propeller pitch in inches

3. Type of propeller (propeller mark)

ZMU04608

-

x

123

General information

11

rise above the maximum recommended

range, reduce the throttle setting to maintain

the engine in the proper operating range.

For instructions on propeller removal and in-

stallation, see page 69.

EMU25770

Start-in-gear protection

Yamaha outboard motors or Yamaha-ap-

proved remote control units are equipped

with start-in-gear protection device(s). This

feature permits the engine to be started only

when it is in neutral. Always select neutral

before starting the engine.

12

Basic components

EMU25799

Main components

NOTE:

* May not be exactly as shown; also may not be included as standard equipment on all mod-

els.

F115, LF115

1

2

3

4

5

6

7

8

9

11

12

13

14

15

16

17

18 19

ZMU04773

10

1. Top cowling

2. Top cowling lock lever(s)

3. Drain screw

4. Anti-cavitation plate

5. Trim tab (anode)

6. Propeller*

7. Cooling water inlet

8. Anode

9. Flushing device

10. Water separator

11. Power trim and tilt switch

12. Remote control box (side mount type)*

13. Remote control box (binnacle mount type)*

14. Switch panel (for use with binnacle type)*

15. Tachometer*

16. Trim meter*

17. Digital speedometer*

18. Digital tachometer*

19. Fuel management meter*

Basic components

13

EMU26180

Remote control

The remote control lever actuates both the

shifter and the throttle. The electrical switch-

es are mounted on the remote control box.

1

4

6

3

2

5

ZMU05429

1. Tachometer unit (Square type)*

2. Tachometer unit (Round type)*

3. Speedometer unit (Square type)*

4. Speed & fuel meter unit (Square type)*

5. Speed & fuel meter unit (Round type)*

6. Fuel management meter (Square type)*

1. Power trim and tilt switch

2. Remote control lever

3. Neutral interlock trigger

4. Neutral throttle lever

5. Main switch / choke switch

6. Engine stop lanyard switch

7. Throttle friction adjuster

Basic components

14

EMU26190

Remote control lever

Moving the lever forward from the neutral po-

sition engages forward gear. Pulling the le-

ver back from neutral engages reverse. The

engine will continue to run at idle until the le-

ver is moved about 35° (a detent can be felt).

Moving the lever farther opens the throttle,

and the engine will begin to accelerate.

EMU26201

Neutral interlock trigger

To shift out of neutral, first pull the neutral in-

terlock trigger up.

EMU26211

Neutral throttle lever

To open the throttle without shifting into ei-

ther forward or reverse, put the remote con-

trol lever in the neutral position and lift the

neutral throttle lever.

1. Remote control lever

2. Power trim and tilt switch

3. Free accelerator

4. Throttle friction adjuster

1. Neutral “ ”

2. Forward “ ”

3. Reverse “ ”

4. Shift

5. Fully closed

6. Throttle

7. Fully open

2

3

2

1

4

ZMU04569

1. Neutral “ ”

2. Forward “ ”

3. Reverse “ ”

4. Shift

5. Fully closed

6. Throttle

7. Fully open

1. Neutral interlock trigger

N

1

F

7

6

2

R

3

4

6

5

7

5

ZMU04573

Page is loading ...

Yamaha F115, LF115 Owner's manual

Related papers

Other documents