AMX AP-TTS16 Installation guide

AMX
Brand
AMX
Model
AP-TTS16
Category
Mounting kits
Type
Installation guide
Installation Guide
AP-TTS16-BL Table-Top Stand for Novara US 16-Button KeyPads/ControlPads
Overview
The AP-TTS16-BL Table Top Stand (FG1301-17) for 16-Button US Novara
KeyPads and ControlPads (Keypads and ControlPads not included) provides a
table top installation option for conference rooms and residential applications.
Installation
The following sections describe each step required to install a Novara 16-Button
US-Style Keypad or ControlPad into the AP-TTS16-BL Table-Top Stand.
Note: Before touching the device, discharge the static electricity from your body
by touching a grounded metal object.
Step 1: Disconnect ControlPad Wiring
If connected, disconnect all wiring from the KeyPad or ControlPad.
• Novara 16-button KeyPads and ControlPads use a set of captive-wire
connectors on the rear panel for all control and power wiring connections.
• Novara ControlPads also feature a USB device configuration port on the
top panel of the backbox. This connector is only intended to be used for
configuration, so it typically is not connected at all times.
Note that once the ControlPad is installed into the Table-Top Stand, the
USB port will not be accessible.
Refer to the NOVARA 1000 Series ControlPads Installation Guide (available at
www.amx.com) for wiring and connection details.
Step 2: Establish Internal Connections
FIG. 2 indicates the location of the AxLink connector on the rear panel of the
SP-16-AX-TR-US KeyPad:
FIG. 3 indicates the connectors on the rear panel of the SP-16-AX-TR-US
ControlPad:
The cables are pre-installed in the cable strain relief inside the enclosure.
Connect the cables directly to the captive-wire connector terminal on the rear
panel of the KeyPad or ControlPad (FIG. 4).
FIG. 1 AP-TTS16-BL with KeyPad installed (KeyPad not included)
Specifications
Compatible With: Novara SP-16-AX-TR-US 16-Button KeyPad (US) With
AxLink (FG1301-16-SW/SB/SA)
Novara CP-1016-TR-US 16-Button ControlPad (US)
(FG1311-16-SW/SB/SA)
Note: AP-TTS-16-BL Table-Top Stands are designed
specifically for use only with Novara 16-Button US-Style
Keypads and ControlPads. Do not mount any other device
in the AP-TTS-16-BL.
Enclosure: Metal with matte black finish
Dimensions (HWD): • Decimal inches: 3.500” x 6.693” x 5.022”
• Fraction Inches (approx): 3 1/2” x 6 11/16” x 5 1/32”
• Metrics: 8.89cm x 17cm x 12.75cm
Weight: 1.2 lbs. (0.54 kg)
Included
Accessories
• Strain Relief Bracket (62-1800-06)
• Strain Relief (45-0004-04)
• 10’ (3.048m) 4-Conductor Cable (64-9514)
• 10’ (3.048m) 8-Conductor Cable (64-9538)
AP-TTS16-BL
Enclosure
AP-TTS16-BLL
Bezel
KeyPad / ControlPad
Faceplate assembly
FIG. 2 SP-16-AX-TR-US KeyPad - rear panel
FIG. 3 CP-1016-TR-US ControlPad - rear panel
FIG. 4 AP-TTS-16-BL Internal view
4-wire AxLink connector
SHARED 12V
Cable strain relief
For full warranty information, refer to the AMX Instruction Manual(s) associated with your Product(s).
1/10
©2010 AMX. All rights reserved. AMX and the AMX logo are registered trademarks of AMX.
AMX reserves the right to alter specifications without notice at any time.
3000 RESEARCH DRIVE, RICHARDSON, TX 75082 • 800.222.0193 • fax 469.624.7153 • technical support 800.932.6993 • www.amx.com
93-1301-17 REV: B
Step 3: Install The KeyPad or ControlPad Into the Table-Top
Stand
At this point the KeyPad or ControlPad can be installed into the Table-Top Stand
enclosure:
1. Slide the KeyPad or ControlPad into the Table-Top Stand from the front,
until the faceplate on KeyPad or ControlPad sits flush against the front
panel of the Table-Top Stand.
2. Use the six mounting screws (included) to secure the KeyPad or
ControlPad to the Table-Top Stand enclosure (FIG. 5).
3. Slide the Rear Bezel onto the Table-Top Stand from the rear, as shown in
FIG. 5.
Note: Be sure that the adhesive on the Rear Bezel is facing up when the
Bezel is installed.
4. Peel the backing off of the adhesive on the Rear Bezel.
5. Press the Rear Bezel against the back of the Faceplate assembly. The
adhesive will secure the Rear Bezel to the Faceplate.
Secure Mounting / Alternate Cable Routing
The AP-TTS16-BL features a cable routing knockout on the bottom panel,
mounting holes and internal strain relief to provide a secure table-top installation
option (FIG. 6).
Refer to the TTS Secure Mounting / Alternate Cable Routing Installation Guide
(available at www.amx.com) for instructions.
Additional Documentation
Refer to the NOVARA ControlPads & KeyPads Operation/Reference Guide
(available at ww.amx.com) for details on wiring and connection information for
the ControlPads.
FIG. 5 Installing the KeyPad or ControlPad into the AP-TTS16-BL
KeyPad / ControlPad
Table-Top Stand
Rear Bezel
Mounting Screws (6)
Faceplate assembly
adhesive (remove backing)
FIG. 6 Bottom Panel (Alternate Cable Routing)
(rear)
Surface Mounting holes are
beneath the rubber feet
Surface Mounting holes
Cable knockout
The Strain Relief Bracket
(mounted inside the enclosure)
also uses this mounting hole
  • Page 1 1
  • Page 2 2

AMX AP-TTS16 Installation guide

AMX
Brand
AMX
Model
AP-TTS16
Category
Mounting kits
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents