6(59,&(0$18$/
Please read and follow these instructions before using your unit.
OVERVIEW OF THE PLAYER
CD/WMA PLAYER WITH RADIO
AND USB READER
MODEL:&'58
1
LOCATION OF CONTROLS
1. PROGRAM BUTTON
2. SKIP/SEARCH DOWN BUTTON
3. POWER INDICATOR
4. CD DOOR
5. LCD DISPLAY
6. SKIP/SEARCH UP BUTTON
7. MODE BUTTON
8. CD DOOR OPEN AREA
9. SPEAKERS
10. STOP/USB BUTTON
11. USB PORT
12. AUX IN JACK
13. PLAY/PAUSE BUTTON
14. TUNING CONTROL
15. BAND SWITCH
16. FM TELESCOPIC ANTENNA
17. AC SOCKET
18. BATTERY COMPARTMENT
19. FUNCTION SWITCH
20. VOLUME CONTROL
21.
22. FM ST. INDICATOR
FOLDING HANDLE
12
3
4
5
6 7 8
9 1011 1213
14 15 16
9
17
18 19 20
21
22
POWER SUPPLY
NOTE:
TO PLAY THE RADIO
q
q
BATTERY OPERATION
AC OPERATION
1. Remove the battery compartment cover gently.
2. Install 6 x 'C' size batteries (UM-2 or equivalent) while observing the correct polarities.
3. Replace the battery compartment cover.
The AC cord must be detached from the AC socket of the player.
Leaking batteries may damage the battery cabinet and the player as a whole, so
they should be removed from the cabinet when becoming flat or when the player is
not to be played on batteries for some time.
NOTE:
=
=
Insert the AC cord to the AC socket of the player, and plug the other end to an
applicable wall outlet.
If the AC plug of this unit does not fit in with your AC outlet, a plug adaptor
should be used. Consult your local dealer on the type of plug adaptor.
1. Set the FUNCTION switch to the RADIO position, the POWER Indicator will light up.
2. Select the desired band with the BAND switch.
3. Tune to the desired station by rotating the TUNING control (rotate that control back and
forth until you get the strongest and clearest reception).
4. When FM (stereo) station is received, the FM indicator will be lit up.
5. The built-in AM antenna and external FM TELESCOPICANTENNAare directional.
When you are receiving an FM (stereo) broadcast, fully extend the TELESCOPIC
ANTENNA and rotate it for the best reception.
For AM broadcast, rotate the whole set until the best reception is heard.
6. Adjust the volume level to a comfortable listening level.
7. To turn off the radio, set the FUNCTION switch to the OFF, CD/USB/AUX position.
=
=
3
2
HANDLING AND MAINTENANCE OF A DISC
Follow the instructions below to handle and maintain your disc in order
that long time and trouble free performance can possibly be obtained:
=
=
=
=
=
Ensure not to caress the rain bow side of the disc; handle the disc
by the edge.
Long time exposure to sunshine, high temperatures and humidity
will damage the disc. And keep storage area clean.
Avoid sticking labels on both sides of a disc. Writing with pointed
articles on the disc should be strictly avoided.
Clean the disc wiping the centre and then working out to the edge
with a dry & soft cloth or a disc brush. Avoid any cleansing lotion or
chemical eradicator.
Store them in their cases when they are not to be used.
HANDLE DISC ONLY AS SHOWN
CLEAN FROM CENTER TO EDGE
DO NOT STORE NEAR HEAT
LOAD A DISC
PLAY A DISC
1. Open the CD door by the Door open area.
2. Load a disc on the disc tray with the label side facing up.
3. Close the CD door.
1. Slide the Function switch to CD/USB/AUX position.
2. Follow the steps above to load a disc.
3. The player begins reading disc immediately.
4. When the disc is successfully read, total number of tracks shows in the LCD and
playback follows with the first track.
5. Press Play/Pause button once to halt music playback, the track number flashes to
indicate the player in Pause mode; press Stop button to cease music playback. The
LCD shows the total number of tracks again.
SKIP TRACKS AND SEARCH FOR A SPECIFIC POINT TO PLAY (CD)
PROGRAMMED PLAY (CD/USB/WMA)
1. Press once the SKIP/SEARCH up button in music play to skip to the next track. To skip
to a specific track ahead, press this button several times.
2. Press once the SKIP/SEARCH down button in music play to skip to the previous track.
To skip to a specific track at back, press this button several times.
3. Hold the SKIP/SEARCH up button in music play to search at quick rate for a specific
point to play.
4. Hold the SKIP/SEARCH down button in music play to search at quick rate for a specific
point to play.
Programmed play is that tracks on the disc or on the USB can be edited for playback in a
preferred order with the use of PROGRAM button.
In stop mode, press PROGRAM button once, the program sequence indication "P01"
flashes first with "PROG." icon in the LCD. Then a flickering track number shows in the
LCD with "PROG." icon waiting for your input, select the first track to be programmed using
SKIP/SEARCH buttons, and press PROGRAM button again to store and advance to the
next programming step. The program sequence indication changes to "P02" waiting for
your next input.
Repeat the steps above to program more tracks. A maximum of 20 tracks for CD and 99
tracks for USB & WMA can be programmed in memory in a preferred order.
Press PLAY/PAUSE button to begin programmed play in the preferred order after you are
done with programming. The player stops automatically after all programmed tracks are
played.
You may press STOP button to terminate programmed playback. In program stop mode,
press STOP button again to clear the programming; press PLAY/PAUSE button to begin
the programmed playback with the programming order identical with the previous one done.
WMA-CD PLAYBACK
SKIP TRACKS AND SEARCH FOR A SPECIFIC POINT TO PLAY
REPEAT A SINGLE TRACK (CD/USB/WMA)
REPEAT ALL TRACKS (CD/USB/WMA)
RANDOM PLAY (CD/USB/WMA)
INTRODUCTION PLAY (CD/USB/WMA)
This player is capable of WMA-CDs. It takes longer time for this player to read an WMA-CD
than it does CD-DA. Wait patiently while it is reading.
After an WMA-CD is successfully read, the total tracks number shows in the LCD. And a
second later, playback begins from the first track of the first album with the icon of
"WMA"showing on the screen.
1. Press once the SKIP/SEARCH up button in music play to skip to the next track. To skip
to a specific track ahead, press this button several times.
2. Press once the SKIP/SEARCH down button in music play to skip to the previous track.
To skip to a specific track at back, press this button several times.
3. Hold the SKIP/SEARCH up button in music play to search at quick rate for a specific
point to play.
4. Hold the SKIP/SEARCH down button in music play to search at quick rate for a specific
point to play.
To repeat a preferred track in playback, press MODE button once, the corresponding icon
of repeat a single track shows in the LCD. Then select the preferred track using
SKIP/SERCH buttons. The player will repeat the chosen track until you press STOP button.
To repeat all tracks, press MODE button twice in play mode, the corresponding icon of
repeat all tracks shows in the LCD. The player will repeat all tracks until you press STOP
button.
Random play is that tracks on the disc are played by the player at random. Press MODE
button three times to enter this mode during play, the icon of random play shows in the LCD.
Tracks on the disc will be selected at random for playback and the player stops
automatically after all tracks are played.
Introduction play is that the first ten seconds of each track are played in a sequential order.
Press MODE button four times to enter this mode during play, the icon of introduction play
shows in the LCD. Press SKIP/SEARCH up button in Introduction mode to begin
Introduction play from the next track immediately after the current track. Press
SKIP/SEARCH down button in Introduction mode to begin Introduction play from the
previous track. Press Play/pause button to resume normal play from the current track.
Press MODE button once more to exit introduction and return to normal playback from the
track the unit plays.
You may press STOP button to exit random play
mode and press PLAY/PAUSE button to resume normal playback.
5
4
EXTERNAL MEMORY MEDIA OPERATION (USB)
Prepare the player for external memory media operation
VARIOUS PLAY MODES (USB)
Insert a USB data traveller into the USB port; slide the FUNCTION switch to the
CD/USB/AUX position and press and hold STOP/USB button to switch to USB mode (in
STOP mode). Playback will start from the first track after reading the USB successfully.
SKIPPING TRACKS AND SEARCHING BETWEEN TRACKS
Press SKIP UP button once to skip the current track and play the next track, press this
button continuously to go to corresponding tracks ahead;
Press SKIP DOWN button once to skip the current track and go back to the previous track,
press this button continuously to go back to corresponding tracks at back.
Press and hold SKIP buttons to initiate high-rate scanning between tracks; release one of
them to begin playback of music at normal speed.
AUXILIARY IN
Your player can be used as a power amplifier to playback the programs from portable radio,
TV set or whatever provided this appliance is so designed that audio signal may be
produced through a LINE-OUT jack or the like.
Observe the following steps to connect the player to another appliance:
1. Power the player on using the supplied AC Power Cord.
2. Slide Function Switch to CD/USB/AUX position.
3. Connect the appliance into the player's AUX in jack with the supplied LINE OUT cable
of the appliance.
4. Power on the appliance and begin play.
Easy job, right? At this time you will be able to hear the sound produced from the programs
the connected appliance is broadcasting.
IMPORTANT SAFETY INSTRUCTIONS
The apparatus shall not be exposed to dripping or splashing and that no objects filled
with liquids, such as vases, shall be placed on the apparatus.
When the mains plug or an appliance coupler is used as the disconnect device, the
disconnect device shall remain readily operable. To be completely disconnected the
power input, the mains plug of the apparatus or the appliance coupler shall be
disconnected from the mains completely.
No naked flame sources, such as lighted candles, should be placed on the apparatus.
Minimum distances 2.0cm around the apparatus for sufficient ventilation. The ventilation
should not be impeded by covering the ventilation openings with items, such as
newspapers, table-cloths, curtains, etc.
The use of apparatus is in tropical and/or moderate climates.
Attention should be drawn to the environmental aspects of battery disposal.
CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only with the
same or equivalent type.
Battery shall not be exposed to excessive heat such as sunshine, fire or the like.
The marking plate is located at the bottom of the apparatus.
45
44
41
42
40
49
46
39
38
36
37
35
33
34
28
5
1
2
3
4
7
9
10
11
12
14
15
16
17
29
26
25
24
23
22
21
12
20
19
18
31
8
8
5
13
43
5
48
47
32
6
1
2
1
2
1
1
2
1
8
1
1
VOLUME KNOB
AC SOCKET PRESS
AC SOCKET
BATTERY PCB
BOTTOM CABINET
BATTERY PCB COVER
BACK PLATE
1
1
37
40
41
42
39
38
34
36
35
DESCRIPTION QTY.
2
1
3
4
5
6
8
9
7
NO
CD BUTTONS
LCD BRACKET
SPEAKER METAL NET
FRONT BRACKET
BATTERY DOOR
SCREW PA3X16
110/220 SWITCH
BUTTON
1
2
1
1
49
43
46
47
48
44
45
1
1
1
1
1
1
1
1
AC TRANSFORMER
10
11
13
12
15
16
17
18
14
20
22
23
21
24
25
28
27
26
19
SPEAKER
KEY PCB
METAL WASHER
ANTENNA ROD
SCREW WA3X10
CD DOOR
SCREW PM3X8X0.5
TOP CABINET
CD DOOR SPRING
LEAF SWITCH
SCREW PA2X12
LCD LENS
1
4
6
1
29
30
31
32
33 CD DECK
CD CUSHION RUBBER
FIBRE WASHER
TUNING KNOB
1
DAMPER WHEEL/BRACKET
27
28
30
30
SCREW WA3X8
8
SCREW PA2X8
4
PVC BRACKET
1
SCREW PM26X6
3
MAIN PCB
1
2
LCD
1
SCREW WA26X8
8
USB PCB
1
SCREW PB3X6
4
CONNECTOR PLATE
1
SCREW PA3X12
2
SCREW WA2X8
2
BATTERY PCB
1
SCREW WA3X14
2
SCREW KB2X6
2
RUBBER FOOT 2
NO
DESCRIPTION QTY.
PDF created with pdfFactory Pro trial version www.pdffactory.com
BRANCH: KC
BAND: 1 OF 7
NAME: BBU109B-A001
DESCRIPTION: AF-S+POWER+ALI (SMT)
SA2132C+M5673+青雅機芯
PROD.LINE: 553
P/SET: 1.000
NO. OF ITEMS: 50
# CODE NO. DESCRIPTION
1 0010-BBU109B-001 P.C.B BBU109B AM/FM+MAIN ALI S-SIDE
BOARD REV-0 ROHS
2 0030-08550-054 CHIP TRANSISTOR MMT8550C SOT-23
PNP ROHS
3 0030-09014-022 CHIP TRANSISTOR S9014C (SOT-23) ROHS
4 0030-09015-022 CHIP TRANSISTOR S9015 (SOT-23) ROHS
5 0040-FB-009 CHIP INDUCTORS FB 0 OHM (0805) RoHS
6 0040-O100J-040 Chip Ferrite Inductors 10 UH 10% (0603)
RoHS
7 0050-B000B-027 CHIP RESISTOR 0 ohm (1206) +/-5% ROHS
8 0050-S000B-013 CHIP RESISTOR 0 OHM (0603) +/-5% 1/8W
ROHS
9 0050-S102B-013 CHIP RESISTOR 1 K (0603) +/-5% 1/8W
ROHS
10 0050-S103B-013 CHIP RESISTOR 10 K (0603) +/-5% 1/8W
ROHS
11 0050-S104B-013 CHIP RESISTOR 100K (0603) +/-5% 1/8W
ROHS
12 0050-S123B-013 CHIP RESISTOR 12K (0603) +/-5% 1/8W
ROHS
NL MODEL: BBU109B
BRAND:
BUYER MODEL:
BUYER: NEW SAN
PO NO.: 3964
毅力企業有限公司
MATERIAL REQUISITION SUMMA
R
JOB NO: CJ024850/10
13 0050-S150B-013 CHIP RESISTOR 15 OHM (0603) +/-5% 1/8W
RoHS
14 0050-S151B-013 CHIP RESISTOR 150 OHM (0603) +/-5%
1/8W RoHS
15 0050-S152B-013 CHIP RESISTOR 1.5K (0603) +/-5% 1/8W
RoHS
16 0050-S154B-013 CHIP RESISTOR 150K (0603) +/-5% 1/8W
RoHS
17 0050-S181B-013 CHIP RESISTOR 180 OHM (0603) +/-5%
1/8W RoHS
18 0050-S221B-013 CHIP RESISTOR 220 OHM (0603) +/-5%
1/8W RoHS
19 0050-S222B-013 CHIP RESISTOR 2.2K (0603) +/-5% 1/8W
RoHS
20 0050-S223B-013 CHIP RESISTOR 22K (0603) +/-5% 1/8W
RoHS
21 0050-S224B-013 CHIP RESISTOR 220K (0603) +/-5% 1/8W
RoHS
22 0050-S243B-013 CHIP RESISTOR 24K (0603) +/-5% 1/8W
RoHS
23 0050-S272B-013 CHIP RESISTOR 2.7K (0603) +/-5% 1/8W
RoHS
24 0050-S273B-013 CHIP RESISTOR 27K (0603) +/-5% 1/8W
RoHS
25 0050-S332B-013 CHIP RESISTOR 3.3K (0603) +/-5% 1/8W
RoHS
26 0050-S333B-013 CHIP RESISTOR 33K (0603) +/-5% 1/8W
RoHS
27 0050-S470B-013 CHIP RESISTOR 47 OHM (0603) +/-5% 1/8W
RoHS
28 0050-S471B-013 CHIP RESISTOR 470 OHM (0603) +/-5%
1/8W RoHS
29 0050-S472B-013 CHIP RESISTOR 4.7K (0603) +/-5% 1/8W
RoHS
30 0050-S473B-013 CHIP RESISTOR 47K (0603) +/-5% 1/8W
RoHS
31 0050-S47XB-013 CHIP RESISTOR 4.7 OHM (0603) +/-5%
1/8W RoHS
32 0050-S561B-013 CHIP RESISTOR 560 OHM (0603) +/-5%
1/8W RoHS
33 0050-S562B-013 CHIP RESISTOR 5.6K (0603) +/-5% 1/8W
RoHS
34 0050-S820B-013 CHIP RESISTOR 82 OHM (0603) +/-5% 1/8W
RoHS
35 0160-S0501-006 CHIP CAPACITOR 5 PF 50V (0603) +-0.25
PF NPO ROHS
36 0160-S1005-006 CHIP CAPACITOR 10 PF 50V (0603) +/-5%
NPO ROHS
37 0160-S1015-006 CHIP CAPACITOR 100 PF 50V (0603) +/-5%
NPO ROHS
38 0160-S1026-006 CHIP CAPACITOR 1000 PF 50V (0603) 10%
X7R ROHS
39 0160-S1036-006 CHIP CAPACITOR 0.01UF 50V (0603) +/-
10% X7R ROHS
40 0160-S1047-004 CHIP CAPACITOR 0.1 UF 25V (0603) 20%
Y5V ROHS
41 0160-S2036-006 CHIP CAPACITOR 0.02 UF (0603) +/-10%
X7R ROHS
42 0160-S2205-006 CHIP CAPACITOR 22 PF 50V (0603) +/-5%
NPO ROHS
43 0160-S2226-006 CHIP CAPACITOR 2200 PF 50V (0603) +/-
10% X7R RoHS
44 0160-S2236-006 CHIP CAPACITOR 0.022 UF (0603) +/-10%
X7R ROHS
45 0160-S3005-006 CHIP CAPACITOR 30 PF 50V (0603) +/-5%
NPO ROHS
46 0160-S4715-006 CHIP CAPACITOR 470 PF 50V (0603) 5%
X7R ROHS
47 0160-S4736-006 CHIP CAPACITOR 0.047 UF 50V (0603) +/-
10% X7R ROHS
48 0160-S4746-004 CHIP CAPACITOR 0.47 UF 25V (0603) 10%
X5R ROHS
49 0210-005-S DIODE LL4148
(
SMT
)
LL34 ROHS
50 0210-Z0056-S DIODE ZENER 5.6V
(
SMT
)
ROHS
審批﹕
BRANCH: KC
BAND: 2 OF 7
NAME: BBU109B-A004
DESCRIPTION: AF-S+POWER+ALI (NOR)
SA2132C+M5673+青雅機芯 (白色USB插)
(
帶AUX IN功能
)
(
中頻﹕465
)
PROD.LINE: 553
P/SET: 1.000
NO. OF ITEMS: 68
# CODE NO. DESCRIPTION
1 0020-01117-700 I.C. B1117C/MXT1117 0.8A 3.3 V SOT-223
RoHS
2 0020-01469-P00 I.C. CSC1469PH 3.3V MOTOR DRIVE RoHS
NL MODEL: BBU109B
BRAND:
BUYER MODEL:
BUYER: NEW SAN
PO NO.: 3964
毅力企業有限公司
MATERIAL REQUISITION SUMMA
R
JOB NO: CJ024850/10
*** nothing follows ***
制表﹕魏德梅
3 0020-02132-C68 I.C. SA2132C DIP-16 FM F/E+AM/FM IF
4 0020-02206-109 I.C. KA2206B 2.3W DUAL AMP ROHS
5 0020-05673-117 I.C. M5673 CD SD/USB AUDIO SINGLE
RoHS
6 0020-08854-030 I.C. CSC8854 ROHS
7 0020-25F10-000 I.C. EN25F10-100GCP SOP-8 1M-BIT FLASH
MEMORY
[
燒錄
]
RoHS
8 0030-00882-004 TRANSISTOR 2SD882/3DA882/HS882 (NPN)
TO-126 ROHS
9 0030-08050-014 TRANSISTOR S8050 TO-92 RoHS
10 0030-08550-N14 TRANSISTOR 8550N NEC TO-92 PNP ROHS
STS8550/S8550
11 0040-3-150 CHOCK COIL 15 UH +/-10% RC0308T-150K
(
V
)
RoHS
12 0050-C221B-023 RESISTOR 220 OHM 1/4W +/-5% ROHS
13 0050-C22XB-023 RESISTOR 2.2 OHM 1/4W +/-5% ROHS
14 0070-101083A I.F.T. 10MM 1083A
(
Red
)
ROHS
15 0070-101083B I.F.T. 10MM 1083B
(
Yellow
)
ROHS
16 0070-101083F I.F.T. 10MM 1083F
(
Pink
)
ROHS
17 0100-CD192-01M HEATSINK (METAL) CDR192A FOR M-
DRIVER ROHS
18 0100-CD60-04 Heatsink FOR 7808 CD60 ROHS
19 0110-A1318-020 CERAMIC CAP. 130 PF 63V +/-20/50%
ROHS
20 0120-A1077-003 ELECT. CAP. 100 MFD 16V +/-20% (5x11)
ROHS
21 0120-A2277-002 ELECT. CAP. 220 MFD 10V +/-20% (5x11)
ROHS
22 0120-A2277-003 ELECT. CAP. 220 MFD 16V +/-20% (6x12)
ROHS
23 0120-A2287-004 ELECT. CAP. 2200 MFD 25V +/-20% (13x25)
ROHS
24 0120-A3357-003 ELECT. CAP. 3.3 MFD 16V +/-20% (5x11)
ROHS
25 0120-A4767-003 ELECT. CAP. 47 MFD 16V +/-20% (5x11)
ROHS
26 0120-A4777-002 ELECT. CAP. 470 MFD 10V +/-20% (6x12)
ROHS
27 0120-C1057-002 ELECT. CAP. MINI 1 MFD 10V +/-20% (4x7)
ROHS
28 0120-C1067-003 ELECT. CAP. MINI 10 MFD 16V +/-20% (4x7)
ROHS -50:c/+105:c
(
M
)
29 0120-C1077-001 ELECT. CAP. MINI 100 MFD 6.3V +/-20%
(
4x7
)
ROHS -50:C/+105:C
(
M
)
30 0120-C2258-006 ELECT. CAP. MINI 2.2 MFD 50V +/-20%
(
4x7
)
ROHS
31 0120-C2267-004 ELECT. CAP. MINI 22 MFD 25V +/-20% (4x7)
ROHS
32 0120-C4747-002 ELECT. CAP. MINI 0.47 MFD 10V +/-20% 4x7
RoHS
33 0120-C4757-002 ELECT. CAP. MINI 4.7 MFD 10V +/-20% 4x7
RoHS
34 0120-C4767-002 ELECT. CAP. MINI 47 MFD 10V +/-20%
4x7mm RoHS -50:C/+105:C
35 0130-A1026-000 MYLAR CAP. 0.001 UF +/-10% ROHS
36 0170-51355 Ferrite Bar 5x13x55mm ROHS
37 0180-05-07 BAR HOLDER 5MM BCX108A ROHS
38 0190-01R CERAMIC FILTER LT10.7MA5A
(
RED
)
10.7MA5A 3 PIN ROHS
39 0190-20 CERAMIC FILTER SFU465B ROHS
40 0210-010-2 DIODE IN4001 COSMOS ROHS
41 0210-100 DIODE ZENER 4.3V DO-35 ROHS
42 0210-2638 DIODE AFC/SEL IS2638 DO-35 RoHS
43 0210-5818 DIODE IN5818 DO-41 ROHS
44 0210-Z0033 DIODE ZENER 3.3V 0.5W DO-35 DIP RoHS
45 0210-Z0075 DIODE ZENER 7.5V DO-35 DIP ROHS
46 0230-00231-005D P.V.C. AM/FM 443DF2B 100-280gf.CM (T15)
ROHS
47 0240-16.934MHz-A RESONATOR CERAMIC 16.934MHZ 2PIN
16
p
f RoHS
48 0250-005K3 SEMI FIXED 5K OHM 3 PIN +,-20% ROHS
49 0270-005 VOL R1615G A20K X2 L=10MM
(
F
)
ROHS
50 0280-049 USB SOCKET USB-820AMB-T BCU125F
RoHS
51 0290-1035N BAND SWITCH SK-22J01-G10-180 ROHS
52 0290-1047 BAND SWITCH SK-43D01G12
53 0300-1027P 3.5MM STEREO 3 PIN+2X2JACK ST-203-
003AD ROHS
54 0330-125-20-120 AM COIL 125:20 (0.10x1) L=120MM @11MM
ROHS
55 0350-4545-01 FM Coil 4.5mm x 4 1/2T ROHS
56 0350-5025-01 FM Coil 5mm x 2 1/2T ROHS
57 0350-5035-01 FM Coil 5mm x 3 1/2T ROHS
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
/