Sunnydaze Decor LOE-401 Installation guide
- Category
- Fireplaces
- Type
- Installation guide
ELECTRIC FIREPLACE INSERT
EF-A/B Page 1 / 11
WARNING
Read and understand this entire manual, including all safety information,
electric shock, or serious personal injury.
WARNING!
Manufacturer and seller expressly disclaim any and all liability from personal injury, property damage
or loss, whether direct or indirect, or incidental, resulting from the incorrect attachment, improper use,
inadequate maintenance, or neglect of this product.
Thank you for choosing Sunnydaze Decor. We stand behind our brand and the quality of the items we sell.
Replacement parts or products will be sent at our discretion within the 1-year warranty period. Proof of purchase, with
the date of purchase as well as photos of the merchandise defect, must be provided. Photos are used to determine
the cause of defects and for future quality control. Register your warranty at https://tiny.cc/SunnydazeWarranty
If you have any questions, comments or concerns, feel free to contact us by phone at 833-982-1977, by email:
customerservice@sunnydazedecor.com, or via our contact us page at https://tiny.cc/SunnydazeContact
Purchase Date: / / Order/Customer Reference Number:
Inspect packaging to ensure all
parts are accounted for before
disposing of packing materials.
AFireplace 1
BM4 x 12mm Wood Screw 5
ERemote Control 1 CHOKING HAZARD — This item contains small parts that can
be swallowed. Keep children away during assembly.
WARNING
2-PERSON
INSTALLATION
5/2021
Page 2 / 11
IMPORTANT SAFETY INFORMATION
WARNING
Read all instructions before using this heater!
• This heater is hot when in use. To avoid burns, DO NOT touch hot surfaces.
• Keep combustible materials, such as furniture, pillows, bedding, papers, clothes, and curtains at least 3
feet (0.9m) from all sides of the heater.
• If provided, use handles when moving the heater.
• Extreme caution is necessary when any heater is used. NEVER leave the unit unattended while heater
is in use.
• Ensure adequate safety measures are incorporated to protect infants/toddlers from touching hot
surfaces.
• DO NOT operate any heater if the cord is damaged, the heater malfunctions, has been dropped, or
damaged in any manner. Discard heater or have it serviced by a certified professional.
• DO NOT run the power cord under carpeting, throw rugs, runners, or similar floor coverings. DO NOT
route the power cord under furniture or appliances. Arrange power cord away from traffic area, and
where it will not be tripped over.
• Connect to properly grounded outlet ONLY.
• DO NOT insert or allow foreign objects to enter any ventilation or exhaust opening, as this may
damage the heater, cause electric shock or fire.
• DO NOT block air intakes or exhaust in any manner as doing so could cause a fire.
• DO NOT use on soft surfaces, like a bed, where openings may become blocked.
• A heater has arcing or sparking parts inside and becomes HOT. DO NOT use it in areas where
gasoline, paint, or any flammable liquids are used or stored or where flammable vapors are present.
• Only use this heater as described in this manual. Any other use may cause fire, electric shock,
personal injury or death.
• ALWAYS plug heaters directly into a wall outlet/receptacle. NEVER use this unit with an extension
cord or relocatable power tap (power strip).
• DO NOT install the heater near a bed, objects such as pillows or blankets can fall off the bed and be
ignited by the heater.
• NEVER use this heater in bathrooms, laundry rooms, or any other location where the heater could
come in contact with water or be exposed to high moisture.
• AVOID FIRE! It is imperative that the control compartments, circulating blower, and its passageway in
the replace is kept clean. Regularly inspect all air vents to make sure they are free from dust, lint, or
other blockages. Unplug the unit and clean with a vacuum ONLY. DO NOT rinse or get wet.
• NEVER hang this unit on a wall directly below an electrical outlet.
• Ensure clearances to combustibles are maintained when building a mantel or shelves near the
fireplace. Elevated temperatures on the wall or in the air around the fireplace can cause melting,
discoloration or damage to decorations, a TV or other electronic components.
• ALWAYS mount onto the wall bracket before use. DO NOT set this unit on the floor or any other surfaces
to use.
• NEVER use a wall mount bracket from another manufacturer.
WARNING
EF-A/B 5/2021
Page 3 / 11
WARNING
• Do not install the replace against a vapor barrier or exposed insulation.
• For residential use only! NOT for commercial use! Any commercial or public use of this heater voids
all warranties and could cause injury.
• This product is not intended to be a primary heat source. It is for supplemental heat only.
• INDOOR use only! NEVER use this heater outdoors! Doing so may result in electric shock!
• DO NOT OPEN! Risk of electric shock! No user-serviceable parts inside!
• NEVER modify this heater. Doing so could result in personal injury or property damage. Modification of
this fireplace completely voids all warranties.
• ALWAYS turn this heater off before unplugging it from the outlet.
• ALWAYS disconnect this unit from the power supply before performing any assembly or cleaning, or
before relocating the electric fireplace.
• NEVER leave this heater unattended. ALWAYS unplug this heater when it is not in use.
• ALWAYS store this heater in a dry location. NEVER use the fireplace in a location where it may become
wet.
• NEVER plug this heater into an outlet that is old, cracked, or has any loose wires or connections.
Plugging this heater into a faulty outlet could result in electric arcing within the outlet that could cause
the outlet to overheat or catch fire.
• ALWAYS check your heater cord and plug connections with each use!
i) MAKE SURE the plug fits tightly in the outlet! Faulty wall outlet connections or loose plugs can cause
the outlet to overheat.
ii) Heaters draw more current than small appliances. Overheating may occur even if it has not
occurred with the use of other appliances.
iii) During use, frequently check to see if the plug outlet or faceplate is HOT!
iv) If the outlet or faceplate is HOT, discontinue use immediately and have a qualified electrician
inspect and/or replace the faulty outlets.
• The power cord supplied with the heater has a plug
with two flat blades (live and neutral) and one round
pin (ground). If a 3-slot receptacle is not available, an
adapter MUST be used. The adapter MUST be properly
grounded to the outlet box (see figure at right).
• NOTE: Adapter NOT INCLUDED.
• Under no circumstances should this replace be
modied.
WARNING!
Manufacturer and seller expressly disclaim any and all liability from personal injury, property damage
or loss, whether direct or indirect, or incidental, resulting from the incorrect attachment, improper use,
inadequate maintenance, or neglect of this product.
EF-A/B 5/2021
Page 4 / 11
WARNING
W
prevent discoloration.
This product includes a GLASS panel! Always use extreme caution when handling glass.
Failure to do so could result in personal injury or property damage.
Remove all parts and hardware from the carton and place them on a clean, soft, dry surface. Parts and
assembly steps are grouped for free-standing or wall-hanging use. Check the parts list to make sure nothing
is missing. Dispose of packaging materials properly. Please recycle whenever possible.
Before installation, plug the unit into a properly grounded outlet to ensure the unit works properly. This will
avoid the need to remove the insert after installation.
Tools needed for installation (not included): Phillips screwdriver, tape measure, power drill
EF-A/B
Ensure safe clearance:
Minimum clearance on each side: 19.7" (50 cm)
Minimum clearance above: 39.4" (100 cm)
Minimum clearance from the front: 36" (92 cm)
Ensure a properly grounded outlet is within proximity of the unit. Do not use an extension cord.
DO NOT position the unit directly below a power outlet.
See Important Safety Information on pages 2 and 3 for warnings about safe placement, safe installation,
and proper use of this product.
Minimum 39.4″
(100 cm)
Minimum 19.7″
(50 cm)
Minimum 19.7″
(50 cm)
This electric replace is designed for installation into an existing rebox. Ensure the existing rebox opening
is not susceptible to moisture and is away from drapes, furniture and high trac areas.
This unit may be installed into a rebox from front to back, or back to front.
NOTE: Follow all National and local electrical codes.
5/2021
This electric replace is designed for installation into an existing rebox. Ensure the existing rebox opening
is not susceptible to moisture and is away from drapes, furniture and high trac areas.
This unit may be installed into a rebox from front to back, or back to front.
NOTE: Follow all National and local electrical codes.
Page 5 / 11EF-A/B
NOTICE
Before installation, plug the unit into a properly grounded outlet to ensure the unit
works properly. This will avoid the need to remove the insert after installation.
FIREBOX/FRAMING SIZE
LOE-364, 371 21.77" (55.3 cm) 18.31" (46.5 cm) 21.02" (53.4 cm) 17.60" (44.7 cm)
LOE-388, 401 26.77" (68.0 cm) 22.32" (56.7 cm) 26.02" (66.1 cm) 21.61" (54.9 cm)
LOE-418 28.78" (73.1 cm) 23.94" (60.8 cm) 28.03" (71.2 cm) 23.23" (59.0 cm)
W
H
Firebox Opening
Back to FrontFront to Back
H
W
WARNING: Manufacturer and seller expressly disclaim any and all liability from personal injury,
property damage or loss, whether direct or indirect, or incidental, resulting from the incorrect attachment,
improper use, inadequate maintenance, or neglect of this product.
5/2021
Figure 3 Figure 4
Trim Bracket
Figure 2
Fireplace Bracket
Tilt
10-15
degrees
Figure 1
Trim
Page 6 / 11
Read and understand this entire owner’s manual, including all safety information, before
injury, or death.
EF-A/B
It is highly recommended to consult a certied home contractor before installing this appliance on the wall.
1. Unscrew the 4 screws on the unit to remove the trim, as shown. [Figure 1]
2. Find the replace brackets on the sides of replace and tilt them 10-15 degrees toward the front. [Figure 2]
WARNING: Manufacturer and seller expressly disclaim any and all liability from personal injury,
property damage or loss, whether direct or indirect, or incidental, resulting from the incorrect attachment,
improper use, inadequate maintenance, or neglect of this product.
3. Locate the nal location of your replace. Making sure that you have clear access to an electrical outlet,
position the replace mantel close to it's nal location, leaving enough room to access the front of the
mantel. Use (4) M4 x 12mm Wood Screw (B) to ax the replace to rebox. [Figure 3]
4. Clip the trim bracket onto the replace bracket, ensuring the trim is securely connected. [Figure 4]
5/2021
Page 7 / 11EF-A/B
1. Unscrew the 4 screws on the unit to remove the trim, as shown. [Figure 5]
Please keep the trim so that you can use it again in the future.
Figure 5
Figure 6
Trim
WARNING: Manufacturer and seller expressly disclaim any and all liability from personal injury,
property damage or loss, whether direct or indirect, or incidental, resulting from the incorrect attachment,
improper use, inadequate maintenance, or neglect of this product.
2. Locate the nal location of your replace. Making sure that you have clear access to an electrical outlet,
position the replace mantel close to it's nal location, leaving enough room to access the front of the
mantel. Use (4) M4 x 12mm Wood Screw (B) to ax the replace to rebox. [Figure 6]
5/2021
WARNING
remote control and touch panel to no longer function.
MASTER SWITCH
The master power switch must be turned ON (I) for the unit to operate. The unit will make a short alarm sound
to indicate it is ready to use. If no sound is heard, the unit may not be plugged in, the circuit breaker may have
tripped, or there is a malfunction.
Turn the master switch OFF (O) to shut o electric supply.
• Remove the battery housing cover from the back of the remote.
• Paying attention to the positive and negative terminals, gently insert two new 'AAA'
batteries (not included).
• Replace the battery housing cover.
• NOTE: Promptly remove expelled batteries. Do not mix old and new batteries; mixing
batteries could cause the acid inside the batteries to leak, damaging the remote.
REMOTE
explosion. Dispose of batteries at your local hazardous material processing center.
This electric replace can be operated by the CONTROL PANEL, located on the top right side of the replace,
or by the battery-powered REMOTE CONTROL (batteries not included).
The operation and functions of the two methods are the same.
Before operating, please review the IMPORTANT SAFETY INFORMATION on Pages 2 and 3, and heed all
warnings.
Ensure the circuit breaker(s) for the power supply are turned on.
Once the appliance has been plugged into a properly grounded electrical outlet, it is ready to operate.
NOTE: In the event of a power failure, the appliance will lose its memory function and will reset to factory mode
when the power returns.
The Master Power Switch is located on the front top right side of the appliance.
NOTICE
press the buttons too quickly. Give the unit time to respond to each command.
Page 8 / 11EF-A/B 5/2021
Button Function Action and Indication
MASTER
SWITCH
ON (I) Enables all functions.
OFF (O) All functions on the control panel
and remote control are disabled.
1. Press ON (I). Power turns on. All functions
are enabled.
2. Press OFF (O). Power, ame eect, and all
functions turn o.
POWER
ON: Enables control panel and remote
control function. Turns on the ame eect.
OFF: Disables control panel and remote
control function. Turns o the ame eect.
1. Press once. Indicator light turns on. Power
turns on. All functions are enabled.
2. Press again, power and all functions turn
o. Unit goes to standby.
COLOR
COLOR button: Changes the color ame
eect.
9 color settings: C1, C2, C3....C9
1. Press once to change the color ame eect.
2. Press again until desired setting is reached.
FLAME
FLAME button: Makes ame eect brighter
and dimmer.
NOTE: Flame eect stays on until power
button is turned o. Flame eect must be on
for the heater to turn on.
5 brightness settings: L1, L2, L3....L5
1. Press once to change ame color brightness.
2. Press again until desired setting is reached;
L1 is dimmest, L5 is brightest.
HEATER
HEATER button: Turns heater on and o.
NOTE: To prevent overheating, the heater
fan will blow out cool air for 30 seconds after
the heater turn o.
00, LL, HH will show on the display.
1. Press button, LL (low heat) about 750W.
2. Press button, HH (high heat) about 1500W.
3. Press button, 00, heat function is o.
TEMPERATURE
TEMPERATURE button: Changes the
temperature setting.
Setting ranges from 62°F to 82°F
62, 63, 64....82 will show on the display.
Press button until desired setting is reached.
LED display shows selected setting.
Once the desired temperature is reached,
the heater will stop heating the room. Heat
will automatically turn back on when room
temperature falls below the set temperature.
TIMER
TIMER button: Controls the timer settings
to automatically turn the replace o.
Settings range from 1 hour to 8 hours.
0H, 1H, 2H....8H will show on the display.
Press button until desired setting is reached.
LED display will show the setting.
When time reaches the selected setting, the
unit will automatically turn o.
0H disables the timer function.
CONTROL PANEL
NOTICE
should not occur again unless the heater is not used for a long period of time.
Page 9 / 11EF-A/B 5/2021
This heater is equipped with a Temperature Limiting Control. Should the heater reach an unsafe temperature,
the heater will automatically turn OFF.
To reset:
1. Turn the Master Switch OFF (O).
2. Unplug the power cord from the outlet.
3. Wait for at least 15 seconds to 1 minute before plugging the unit back in.
4. Turn the Master Switch ON (I) and press the power button to restart the unit.
5. If the unit does not power on, allow the unit to thoroughly cool down and inspect the replace to make sure
no vents are blocked, or clogged with dust or lint. If they are, use a vacuum to clean the vent areas.
6. If the problem continues, have your outlet and wiring inspected by a professional.
WARNING: Do not move or remove the glass panel when the appliance is plugged in and operating as
it will cause the remote control and touch panel to no longer function.
Cleaning
Page 10 / 11EF-A/B 5/2021
ALWAYS turn the heater OFF and unplug the power cord from the outlet before cleaning,
NEVER immerse in water or spray with water or cleaning solutions. Doing so could result
Metal:
• Dust using a soft cloth. Clean with a slightly damp cloth or duster. Dry thoroughly with a paper towel or a
soft, lint-free cloth.
• DO NOT use brass polish or household cleaners as these products will damage the metal trim.
Glass:
• Use a good quality glass cleaner sprayed onto a cloth or towel to clean the glass. Dry thoroughly with a
paper towel or a soft, lint-free cloth.
• NEVER use abrasive cleansers, liquid sprays, or any cleaner or cloth that could scratch the surface.
Vents:
• Use a vacuum or duster to remove dust and dirt from the heater and vent areas.
• Clean the exterior of the fireplace with a slightly damp cloth or duster.
DO NOT CLEAN WHILE THE UNIT IS HOT! Wait at least 45 minutes after the unit is powered
Page 11 / 11
WARNING!
Manufacturer and seller expressly disclaim any and all liability from personal injury, property damage
or loss, whether direct or indirect, or incidental, resulting from the incorrect attachment, improper use,
inadequate maintenance, or neglect of this product.
Risk of electric shock! DO NOT OPEN! No user-serviceable parts inside!
ALWAYS turn the heater OFF and unplug the power cord from the outlet before cleaning,
Electrical and Moving Parts:
• The fan motors are lubricated at the factory and will not require lubrication.
• Electrical components are integrated in the fireplace and are not serviceable by the consumer.
Storage:
• Store heater in a clean dry place when not in use.
WARNING:
No other servicing should be performed by the consumer. Do not service the
unit yourself.
Maintenance
NOTICE
Keep this owner’s manual for future reference. If you sell or give this product away,
make sure this manual accompanies this product.
EF-A/B 5/2021
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
Sunnydaze Decor LOE-401 Installation guide
- Category
- Fireplaces
- Type
- Installation guide
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Sunnydaze Decor ZHS-449 User guide
-
-
-
-
-
-
-
Other documents
-
Travis 430 Ember-Glo GSR2 Insert Fireplace Xtrodinair User manual
-
Superior Fireplaces VRL3000 Operating instructions
-
-
Blaze King Clarity 2714 IPI Owner's manual
-
Lennox Hearth Products MPE-36R User manual
-
Lennox MPE-36R User manual
-
-
Kozyheat Osseo Linear Owner's manual
-
-
Matsushita MPE-33R User manual
