Aruba JL849AAE Configuration Guide

HPE IMC Orchestrator 6.3 Underlay Network

Configuration Guide

The information in this document is subject to change without notice.

i 
Contents 
Overview ························································································1 
Restrictions and guidelines ·································································2 
Management network configuration ······················································2 
Network configuration ··················································································································· 2 
Configuration example ·················································································································· 3 
Manual underlay network deployment ···················································5 
Network plan ······························································································································· 5 
Network plan for spine-border integration scenario ······································································ 5 
Network plan for spine-border separation scenario ······································································ 7 
Deployment workflow ·················································································································· 10 
Deployment workflow for spine-border integration scenario ························································· 10 
Deployment workflow for spine-border separation scenario ························································· 13 
Procedure (spine-border integration scenario) ················································································· 15 
Configure Spine Border 1 ······································································································ 15 
Configure Spine Border 2 ······································································································ 26 
Configure Server Leaf 1 ········································································································ 37 
Configure Server Leaf 2 ········································································································ 48 
Configure Service Leaf 1 ······································································································ 59 
Configure Service Leaf 2 ······································································································ 69 
Procedure (spine-border separation scenario) ················································································· 79 
Configure Spine 1················································································································ 79 
Configure Spine 2················································································································ 86 
Configure Server Leaf 1 ········································································································ 92 
Configure Server Leaf 2 ······································································································ 103 
Configure Service Leaf 1 ···································································································· 114 
Configure Service Leaf 2 ···································································································· 124 
Configure Border 1 ············································································································ 134 
Configure Border 2 ············································································································ 144 
Automatic underlay network deployment ··········································· 157 
Network plan ··························································································································· 157 
Networking diagram and IP address plan ··············································································· 157 
IP address pool plan ·········································································································· 160 
Deployment workflow ················································································································ 160 
Traditional automatic deployment workflow ············································································ 160 
Wizard-based automatic deployment workflow ········································································ 161 
Traditional automatic deployment procedure ················································································· 161 
Configure IMC Orchestrator basic settings ············································································· 162 
Configure automatic deployment ·························································································· 163 
Configure automatic device deployment ················································································ 173 
Verify the configuration ······································································································· 176 
Wizard-based automatic deployment procedure ············································································· 176 
Configure IMC Orchestrator basic settings ············································································· 177 
Configure automatic deployment ·························································································· 177 
Configure device information ······························································································· 183 
Check device deployment ··································································································· 186 
Configure automatic device deployment ················································································ 187 
Verify the configuration ······································································································· 190 
Scale up the network ········································································································· 191 
Configure link expansion ····································································································· 195 
Underlay network deployment in four-in-one scenario ·························· 198 
Automatic underlay configuration ································································································ 198 
Manual underlay configuration ···································································································· 198 

ii 
Network plan ···················································································································· 198 
Deployment workflow ········································································································· 200 
Configure four-in-one device 1 ····························································································· 202 
Configure four-in-one device 2 ····························································································· 210 
Configure Server Leaf 1 ······································································································ 219 
Configure Server Leaf 2 ······································································································ 228 
Manual underlay network deployment in five-in-one scenario ················· 237 
Network plan ··························································································································· 237 
Deployment workflow ················································································································ 238 
Configure five-in-one device 1 ···································································································· 239 
Reboot the device without a startup configuration file ······························································· 239 
Configure hardware resource parameters ·············································································· 239 
Configure the management network······················································································ 240 
Configure basic settings for L2VPN and VXLAN ······································································ 241 
Configure the underlay routing protocol ················································································· 241 
Configure the VTEP address ······························································································· 241 
Configure the overlay BGP ·································································································· 241 
Enable the VTEP service ···································································································· 241 
Configure the global MAC address ······················································································· 241 
Configure the DRNI physical address ···················································································· 242 
Configure the DRNI virtual address ······················································································· 242 
Configure DR system parameters ························································································· 242 
Configure the DRNI IPP aggregate interface ·········································································· 242 
Configure DRNI MAD ········································································································· 243 
Configure the IPL escape channel ························································································ 243 
Configure the IPL bypass channel ························································································ 244 
Configure default VXLAN decapsulation ················································································ 244 
Configure automatic recovery time of DRNI device after startup ················································· 244 
Configure the DR interface connected to the external LACP aggregate link ·································· 244 
Configure the DR interface connected to Server 1 LACP aggregate link ······································ 244 
Configure the physical interface connected to Server 2 primary and secondary links ······················ 245 
Save the configuration ········································································································ 245 
Incorporate devices on the controller ····················································································· 246 
Configure five-in-one device 2 ···································································································· 248 
Reboot the device without a startup configuration file ······························································· 248 
Configure hardware resource parameters ·············································································· 249 
Configure the management network······················································································ 249 
Configure basic settings for L2VPN and VXLAN ······································································ 250 
Configure the underlay routing protocol ················································································· 250 
Configure the VTEP address ······························································································· 250 
Configure the overlay BGP ·································································································· 250 
Enable the VTEP service ···································································································· 251 
Configure the global MAC address ······················································································· 251 
Configure the DRNI physical address ···················································································· 251 
Configure the DRNI virtual address ······················································································· 251 
Configure DRNI system parameters ······················································································ 251 
Configure the DRNI IPP aggregate interface ·········································································· 252 
Configure DRNI MAD ········································································································· 252 
Configure the IPL escape channel ························································································ 253 
Configure the IPL bypass channel ························································································ 253 
Configure default VXLAN decapsulation ················································································ 253 
Configure automatic recovery time of DRNI device after startup ················································· 253 
Configure the DR interface connected to the external LACP aggregate link ·································· 253 
Configure the DR interface connected to Server 1 LACP aggregate link ······································ 254 
Configure the physical interface connected to Server 2 primary and secondary links ······················ 254 
Save the configuration ········································································································ 255 
Incorporate devices on the controller ····················································································· 255 
(Optional) Harden network security ·················································· 260 
Configure packet suppression ···································································································· 260 
Configure ARP attack protection ································································································· 260 

iii

Configure BPDU guard ············································································································· 260

O&M monitoring ··········································································· 261

1

Overview

The underlay network of the data center is a physical network that carries overlay services and

contains switches such as spine and leaf devices. To deploy overlay services, incorporate underlay

network devices on the data center controller first. This document describes how to incorporate

underlay network devices on the controller.

There are two methods to incorporate underlay network devices on the controller:

• Manual underlay network deployment—This method requires manual pre-configuration on

the devices. After pre-configuration, the underlay network devices can be incorporated by the

controller.

• Automatic underlay network deployment—This method does not require pre-configuration

of underlay devices. You only need to configure templates on the controller and start the

devices without a startup configuration file. The devices can be automatically incorporated by

the controller.

As a best practice, use DRNI to deploy the underlay network for the IMC Orchestrator solution.

2

Restrictions and guidelines

• The addressing plans in this document are for reference only. Before you deploy an underlay

network, create an addressing plan for that network.

• For the ease of fabric expansion, use a routed Layer 3 management network.

• When you use DRNI to deploy the underlay network, follow these guidelines:

 The DR member devices in a DR system must use the same DR system MAC address.

Make sure the DR system MAC address is unique across the whole network.

As a best practice, use the bridge MAC address of one DR member device in the DR

system as the DR system MAC address.

 The DR member devices in a DR system must use different DR system numbers.

For example, set the system number to 1 for DR member device 1 and to 2 for DR member

device 2.

 The DR system priority for the DR member devices in a DR system must be the same.

• You must enable the allowlist function and configure the device list for auto device deployment

in DRNI scenario. Only the devices added to the device list can be automatically deployed and

be incorporated by the controller.

• To avoid DRNI dual-active issues and ensure high availability when both the DRNI keepalive

link and the IPL are down, configure a DRNI MAD DOWN action as follows:

 In an aggregation scenario, enable DRNI standalone mode for the DR member devices:

<Sysname> system-view

[Sysname] drni standalone enable

 In a primary/secondary scenario, enable DRNI MAD DOWN state persistence for the DR

member devices:

<Sysname> system-view

[Sysname] drni mad persistent

• After you enable DRNI MAD DOWN state persistence, a DRNI dual-active issue might still

occur if the keepalive link goes down earlier than the IPL does. In this situation, contact

Technical Support.

• NOTE: The default VXLAN ID range for a switch is 0 to 16777215. If you use the l2vpn drni

peer-link ac-match-rule vxlan-mapping command on a switch in the DMI scenario,

the IDs of the VXLANs created on the switch cannot exceed 16000000. #

Management network configuration

Network configuration

In the data center network, a separate switch is usually used to connect devices and the

management network of the IMC Orchestrator controller. Such a switch is called a management

switch. The management switch requires manual configuration and is not incorporated by the IMC

Orchestrator controller.

The management network of the data center can adopt either Layer 2 networking or Layer 3

networking. For Layer 2 networking, the management network of physical devices and the IMC

Orchestrator management network are located in the same network segment. For Layer 3

networking, the management networks are located in different segments.

Layer 2 networking applies to single-fabric networks. The management network of multi-fabric

networks must use the Layer 3 networking mode. For Layer 3 networking, you need to configure

3

VLANs for the fabric on the management switch, and manually configure the gateway and DHCP

relay agent commands.

As a best practice to facilitate future fabric expansion, use Layer 3 networking in a single-fabric

network. This section takes the deployment of a management network with Layer 3 networking in a

multi-fabric scenario as an example. The typical network diagram is shown in 0.

Note: To perform automatic underlay network deployment, make sure the IP version of the

management network is the same as that of the underlay network (IPv4 or IPv6). #

Management network diagram

Configuration example

In a multi-fabric network, the interfaces that connect the management switch to the devices in

different fabrics must belong to different VLANs. As shown in 0, the interface connected to the

controller management network belongs to VLAN 10, the one connected to Fabric 1 device

management network belongs to VLAN 20, and the one connected to Fabric 2 device management

network belongs to VLAN 30. In addition, you must configure the gateway address of the physical

management network corresponding to the fabric under the VLAN interfaces.

Perform the following tasks on the management switch:

1. Create the VLANs for the controller management network, Fabric 1 device management

network, and Fabric 2 device management network. In this example, the VLAN IDs are 10, 20,

and 30, respectively.

[device] vlan 10

[device-vlan10] quit

[device] vlan 20

[device-vlan20] quit

[device] vlan 30

[device-vlan30] quit

2. Assign the interfaces that connect the management switch to the devices in Fabric 1 to VLAN

20. This section uses the interface Ten-GigabitEthernet 1/0/33 as an example.

Controller

Related components

Management switch

DHCP Relay

VLAN 10

Border1 Border2

Leaf1 Leaf2 Leaf3 Leaf4

Server1 Server2

peer link

peer link peer link

Spine1 Spine2

Fabric1

Border1 Border2

Leaf3 Leaf4Leaf1 Leaf2

Server3 Server4

peer link

peer link peer link

Spine1 Spine2

Fabric2

VLAN 20 VLAN 30

Server3 Server4 Server1 Server2

Management

network（VLAN 10）

Management network

（VLAN 20）

Management

network（VLAN 30）

Management network link description

L3 Network

4

[device] interface Ten-GigabitEthernet1/0/33

[device-Ten-GigabitEthernet1/0/33] port link-mode bridge

[device-Ten-GigabitEthernet1/0/33] port access vlan 20

[device-Ten-GigabitEthernet1/0/33] quit

3. Assign the interfaces that connect the management switch to the devices in Fabric 2 to VLAN

30. This section uses the interface Ten-GigabitEthernet1/0/26 as an example.

[device] interface Ten-GigabitEthernet1/0/26

[device-Ten-GigabitEthernet1/0/26] port link-mode bridge

[device-Ten-GigabitEthernet1/0/26] port access vlan 30

[device-Ten-GigabitEthernet1/0/26] quit

4. Configure the VLAN interface of the controller management network.

[device] interface Vlan-interface10

[device-Vlan-interface10] ip address 192.168.10.1 255.255.255.0

[device-Vlan-interface10] ip address 192.168.12.1 255.255.255.0 sub

[device-Vlan-interface10] quit

5. Configure the VLAN interface of the Fabric1 management network.

[device] interface Vlan-interface20

[device-Vlan-interface20] ip address 192.168.11.1 255.255.255.0

[device-Vlan-interface20] quit

6. Enable DHCP.

Perform this task only when automated deployment is used.

[device] dhcp enable

7. Configure the DHCP relay agent, and specify the controller cluster IP address as the relay

server IP address.

Perform this task only when automated deployment is used.

[device] interface Vlan-interface20

[device-Vlan-interface20] dhcp select relay

[device-Vlan-interface20] dhcp relay server-address 192.168.12.101

[device-Vlan-interface20] quit

8. Configure the VLAN interface of the Fabric 2 management network.

[device] interface Vlan-interface30

[device-Vlan-interface30] ip address 192.168.21.1 255.255.255.0

[device-Vlan-interface30] quit

9. Enable DHCP.

Perform this task only when automated deployment is used.

[device] dhcp enable

10. Configure the DHCP relay agent for the Fabric 2 management network, and specify the

controller cluster IP address as the relay server IP address.

Perform this task only when automated deployment is used.

[device] interface Vlan-interface30

[device-Vlan-interface30] dhcp select relay

[device-Vlan-interface30] dhcp relay server-address 192.168.12.101

[device-Vlan-interface30] quit

5

Manual underlay network deployment

Network plan

Network plan for spine-border integration scenario

In this scenario, the spine and border are integrated as one device, and the two spine-border

devices form a DR system, as shown in 0.

Network diagram for underlay spine-border integration scenario

IP address and interface description for spine-border integration scenario

Device

IP address planning

Interfaces

Spine Border 1

Management IP address:

192.168.11.2/24

Gateway: 192.168.11.1

HGE 4/0/1 (connecting to HGE 4/0/1

on Spine Border 2)

HGE 4/0/2 (connecting to HGE 4/0/2

on Spine Border 2)

XGE 6/0/48 (connecting to XGE

6/0/48 on Spine Border 2)

XGE 6/0/5 (connecting to external

network device)

HGE 1/0/5 (connecting to HGE

1/0/25 on Server Leaf 1)

HGE 1/0/6 (connecting to HGE

1/0/25 on Server Leaf 2)

VTEP address: 10.1.1.2/32

DRNI virtual address: 10.20.1.2/32

DRNI system MAC address:

0002-0003-0001 (or use the bridge

MAC of the device)

DRNI MAD address: 10.10.1.1/30

DRNI IPL escape address:

10.30.1.1/30

Internet

Spine-

Border1 Spine-

Border2

Server-

Leaf1 Server-

Leaf2 Service-

Leaf1 Service-

Leaf2

Server1 Server2

peer link

peer link peer link

Primary

Backup

Controller

Related components

Third-party

firewall

6

Device

IP address planning

Interfaces

HGE 1/0/7 (connecting to HGE

1/0/27 on Service Leaf 1)

HGE 1/0/8 (connecting to HGE

1/0/27 on Service Leaf 2)

Spine Border 2

Management IP address:

192.168.11.3/24

Gateway: 192.168.11.1

HGE 4/0/1 (connecting to HGE 4/0/1

on Spine Border 1)

HGE 4/0/2 (connecting to HGE 4/0/2

on Spine Border 1)

XGE 6/0/48 (connecting to XGE

6/0/48 on Spine Border 1)

XGE 6/0/5 (connecting to external

network device)

HGE 1/0/5 (connecting to HGE

1/0/27 on Server Leaf 1)

HGE 1/0/6 (connecting to HGE

1/0/27 on Server Leaf 2)

HGE 1/0/7 (connecting to HGE

1/0/25 on Service Leaf 1)

HGE 1/0/8 (connecting to HGE

1/0/25 on Service Leaf 2)

VTEP address: 10.1.1.3/32

DRNI virtual address: 10.20.1.2/32

DRNI system MAC address:

0002-0003-0001 (or use the bridge

MAC of the device)

DRNI MAD address: 10.10.1.2/30

DRNI IPL escape address:

10.30.1.2/30

Server Leaf 1

Management IP address:

192.168.11.4/24

Gateway: 192.168.11.1

XGE 1/0/9 (connecting to XGE 1/0/9

on Server Leaf 2)

XGE 1/0/10 (connecting to XGE

1/0/10 on Server Leaf 2)

XGE 1/0/11 (connecting to Server 1)

XGE 1/0/12 (connecting to Server 2)

HGE 1/0/30 (connecting to HGE

1/0/30 on Server Leaf 2)

HGE 1/0/25 (connecting to HGE

1/0/5 on Spine Border 1)

HGE 1/0/27 (connecting to HGE

1/0/5 on Spine Border 2)

VTEP address: 10.1.1.4/32

DRNI virtual address: 10.20.1.4/32

DRNI system MAC address:

0002-0003-0002 (or use the bridge

MAC of the device)

DRNI MAD address: 10.10.1.5/30

DRNI IPL escape address:

10.30.1.5/30

Server Leaf 2

Management IP address:

192.168.11.5/24

Gateway: 192.168.11.1

XGE 1/0/9 (connecting to XGE 1/0/9

on Server Leaf 1)

XGE 1/0/10 (connecting to XGE

1/0/10 on Server Leaf 1)

XGE 1/0/11 (connecting to Server 1)

XGE 1/0/12 (connecting to Server 2)

HGE 1/0/30 (connecting to HGE

1/0/30 on Server Leaf 1)

HGE 1/0/25 (connecting to HGE

1/0/6 on Spine Border 1)

HGE 1/0/27 (connecting to HGE

1/0/6 on Spine Border 2)

VTEP address: 10.1.1.5/32

DRNI virtual address: 10.20.1.4/32

DRNI system MAC address:

0002-0003-0002 (or use the bridge

MAC of the device)

DRNI MAD address: 10.10.1.6/30

DRNI IPL escape address:

10.30.1.6/30

Service Leaf 1

Management IP address:

192.168.11.6/24

Gateway: 192.168.11.1

XGE 1/0/9 (connecting to XGE 1/0/9

on Service Leaf 2)

XGE 1/0/10 (connecting to XGE

7

Device

IP address planning

Interfaces

VTEP address: 10.1.1.6/32

1/0/10 on Service Leaf 2)

HGE 1/0/30 (connecting to HGE

1/0/30 on Service Leaf 2)

HGE 1/0/25 (connecting to HGE

1/0/7 on Spine Border 1)

HGE 1/0/27 (connecting to HGE

1/0/7 on Spine Border 2)

DRNI virtual address: 10.20.1.6/32

DRNI system MAC address:

0002-0003-0003 (or use the bridge

MAC of the device)

DRNI MAD address: 10.10.1.9/30

DRNI IPL escape address:

10.30.1.9/30

Service Leaf 2

Management IP address:

192.168.11.7/24

Gateway: 192.168.11.1

XGE 1/0/9 (connecting to XGE 1/0/9

on Service Leaf 1)

XGE 1/0/10 (connecting to XGE

1/0/10 on Service Leaf 1)

HGE 1/0/30 (connecting to HGE

1/0/30 on Service Leaf 1)

HGE 1/0/25 (connecting to HGE

1/0/8 on Spine Border 1)

HGE 1/0/27 (connecting to HGE

1/0/8 on Spine Border 2)

VTEP address: 10.1.1.7/32

DRNI virtual address: 10.20.1.6/32

DRNI system MAC address:

0002-0003-0003 (or use the bridge

MAC of this device)

DRNI MAD address: 10.10.1.10/30

DRNI IPL escape address:

10.30.1.10/30

Network plan for spine-border separation scenario

Network diagram for underlay spine-border separation scenario

8

IP address and interface description for spine-border separation scenario

Device

IP address planning

Interfaces

Border 1

Management IP address:

192.168.11.8/24

Gateway: 192.168.11.1

HGE 4/0/1 (connecting to HGE

4/0/1 on Border 2)

HGE 4/0/2 (connecting to HGE

4/0/2 on Border 2)

XGE 6/0/48 (connecting to XGE

6/0/48 on Border 2)

HGE 4/0/3 (connecting to HGE

1/0/3 on Spine 1)

HGE 4/0/4 (connecting to HGE

1/0/3 on Spine 2)

XGE 6/0/5 (connecting to external

network device)

VTEP address: 10.1.1.8/32

DRNI virtual address: 10.20.1.8/32

DRNI system MAC address:

0002-0003-0004 (or use the bridge

MAC of this device)

DRNI MAD address: 10.10.1.13/30

DRNI IPL escape address:

10.30.1.13/30

Border 2

Management IP address:

192.168.11.9/24

Gateway: 192.168.11.1

HGE 4/0/1 (connecting to HGE

4/0/1 on Border 1)

HGE 4/0/2 (connecting to HGE

4/0/2 on Border 1)

XGE 6/0/48 (connecting to XGE

6/0/48 on Border 1)

HGE 4/0/3 (connecting to HGE

VTEP address: 10.1.1.9/32

DRNI virtual address: 10.20.1.8/32

DRNI system MAC address:

0002-0003-0004 (or use the bridge

Internet

Border1 Border2

Server-

Leaf1 Server-

Leaf2 Service-

Leaf1 Service-

Leaf2

Server1 Server2

peer link

peer link peer link

Spine1 Spine2

Controller

Related components

Primary

Backup

Third-party

firewall

9

Device

IP address planning

Interfaces

MAC of this device)

1/0/4 on Spine 1)

HGE 4/0/4 (connecting to HGE

1/0/4 on Spine 2)

XGE 6/0/5 (connecting to external

network device)

DRNI MAD address: 10.10.1.14/30

DRNI IPL escape address:

10.30.1.14/30

Spine 1

Management IP address:

192.168.11.2/24

Gateway: 192.168.11.1

HGE 1/0/3 (connecting to HGE

4/0/3 on Border 1)

HGE 1/0/4 (connecting to HGE

4/0/3 on Border 2)

HGE 1/0/5 (connecting to HGE

1/0/25 on Leaf 1)

HGE 1/0/6 (connecting to HGE

1/0/25 on Leaf 2)

HGE 1/0/7 (connecting to HGE

1/0/27 on Leaf 3)

HGE 1/0/8 (connecting to HGE

1/0/27 on Leaf 4)

VTEP address: 10.1.1.2/32

Spine 2

Management IP address:

192.168.11.3/24

Gateway: 192.168.11.1

HGE 1/0/3 (connecting to HGE

4/0/4 on Border 1)

HGE 1/0/4 (connecting to HGE

4/0/4 on Border 2)

HGE 1/0/5 (connecting to HGE

1/0/27 on Leaf 1)

HGE 1/0/6 (connecting to HGE

1/0/27 on Leaf 2)

HGE 1/0/7 (connecting to HGE

1/0/25 on Leaf 3)

HGE 1/0/8 (connecting to HGE

1/0/25 on Leaf 4)

VTEP address: 10.1.1.3/32

Server Leaf 1

Management IP address:

192.168.11.4/24

Gateway: 192.168.11.1

XGE 1/0/9 (connecting to XGE

1/0/9 on Server Leaf 2)

XGE 1/0/10 (connecting to XGE

1/0/10 on Server Leaf 2)

XGE 1/0/11 (connecting to Server

1)

XGE 1/0/12 (connecting to Server

2)

HGE 1/0/30 (connecting to HGE

1/0/30 on Server Leaf 2)

HGE 1/0/25 (connecting to HGE

1/0/5 on Spine 1)

HGE 1/0/27 (connecting to HGE

1/0/5 on Spine 2)

VTEP address: 10.1.1.4/32

DRNI virtual address: 10.20.1.4/32

DRNI system MAC address:

0002-0003-0002 (or use the bridge

MAC of this device)

DRNI MAD address: 10.10.1.5/30

DRNI IPL escape address:

10.30.1.5/30

Server Leaf 2

Management IP address:

192.168.11.5/24

Gateway: 192.168.11.1

XGE 1/0/9 (connecting to XGE

1/0/9 on Server Leaf 1)

XGE 1/0/10 (connecting to XGE

1/0/10 on Server Leaf 1)

XGE 1/0/11 (connecting to Server

VTEP address: 10.1.1.5/32

DRNI virtual address: 10.20.1.4/32

10

Device

IP address planning

Interfaces

DRNI system MAC address:

0002-0003-0002 (or use the bridge

MAC of this device)

1)

XGE 1/0/12 (connecting to Server

2)

HGE 1/0/30 (connecting to HGE

1/0/30 on Server Leaf 1)

HGE 1/0/25 (connecting to HGE

1/0/6 on Spine 1)

HGE 1/0/27 (connecting to HGE

1/0/6 on Spine 2)

DRNI MAD address: 10.10.1.6/30

DRNI IPL escape address:

10.30.1.6/30

Service Leaf 1

Management IP address:

192.168.11.6/24

Gateway: 192.168.11.1

XGE 1/0/9 (connecting to XGE

1/0/9 on Service Leaf 2)

XGE 1/0/10 (connecting to XGE

1/0/10 on Service Leaf 2)

HGE 1/0/30 (connecting to HGE

1/0/30 on Service Leaf 2)

HGE 1/0/25 (connecting to HGE

1/0/7 on Spine 1)

HGE 1/0/27 (connecting to HGE

1/0/7 on Spine 2)

VTEP address: 10.1.1.6/32

DRNI virtual address: 10.20.1.6/32

DRNI system MAC address:

0002-0003-0003 (or use the bridge

MAC of this device)

DRNI MAD address: 10.10.1.9/30

DRNI IPL escape address:

10.30.1.9/30

Service Leaf 2

Management IP address:

192.168.11.7/24

Gateway: 192.168.11.1

XGE 1/0/9 (connecting to XGE

1/0/9 on Service Leaf 1)

XGE 1/0/10 (connecting to XGE

1/0/10 on Service Leaf 1)

HGE 1/0/30 (connecting to HGE

1/0/30 on Service Leaf 1)

HGE 1/0/25 (connecting to HGE

1/0/8 on Spine 1)

HGE 1/0/27 (connecting to HGE

1/0/8 on Spine 2)

VTEP address: 10.1.1.7/32

DRNI virtual address: 10.20.1.6/32

DRNI system MAC address:

0002-0003-0003 (or use the bridge

MAC of this device)

DRNI MAD address: 10.10.1.10/30

DRNI IPL escape address:

10.30.1.10/30

Deployment workflow

Deployment workflow for spine-border integration scenario

Spine border deployment workflow

11

Server leaf deployment workflow

Underlay

basic settings

Start M-LAG

configuration

M-LAG interface

configuration

Reboot the device

without a startup

configuration file

Configure

hardware resource

parameters

Configure the

management

network

Configure basic

settings for L2VPN

and VXLAN

Configure interfaces

connected to the

leaf

Configure the

underlay routing

protocol

Configure the VTEP

address

Enable the OVSDB

VTEP service

Configure the

overlay BGP

Configure the global

MAC address

Configure the M-

LAG physical

address

End

Configure the M-

LAG virtual address

Configure M-LAG

System parameters

Configure the M-

LAG peer link

aggregate interface

Configure M-LAG

MAD

Configure the peer

link failover

channel

Configure the peer

link bypass channel

Configure VXLAN

default

decapsulation

Configure the M-

LAG interface

connected to LB

Configure the M-

LAG interface

connected to FW

Configure the M-

LAG interface

connected to the

external LACP

aggregate link

Incorporation

by controller

Spine

Border

Required main process

Optional main process

Required subprocess

Optional subprocess

12

Service leaf deployment workflow

Configure the M-LAG

interface connected to

Server 1 LACP

aggregate link

Configure the

physical interface

connected to Server

2 primary and

secondary links

Incorporation

by controller

Underlay basic

settings

Start M-LAG

configuration

M-LAG interface

configuration

Reboot the device

without a startup

configuration file

Configure

hardware resource

parameters

Configure the

management

network

Configure basic

settings for L2VPN

and VXLAN

Configure interfaces

connected to the

spine

Configure the

underlay routing

protocol

Configure the VTEP

address

Enable the OVSDB

VTEP service

Configure the

overlay BGP

Configure the

global MAC

address

Configure the M-

LAG physical

address

End

Configure the M-

LAG virtual address

Configure M-LAG

System parameters

Configure the M-

LAG peer link

aggregate interface

Configure M-LAG

MAD

Configure the peer

link failover

channel

Configure the peer

link bypass channel

Configure VXLAN

default

decapsulation

Server

Leaf

Required main process

Optional main process

Required subprocess

Optional subprocess

Underlay basic

settings

Start M-LAG

configuration

M-LAG interface

configuration

Reboot the device

without a startup

configuration file

Configure hardware

resource parameters

Configure the

management

network

Configure basic

settings for L2VPN

and VXLAN

Configure the

underlay routing

protocol

Configure the VTEP

address

Configure the M-LAG

physical address

End

Configure the M-LAG

virtual address

Configure M-LAG

System parameters

Configure the M-LAG

peer link aggregate

interface

Configure M-LAG

MAD

Service

Leaf

Configure interfaces

connected to the

spine

Enable the OVSDB

VTEP service

Configure the

overlay BGP

Configure the global

MAC address

Configure the peer

link failover channel

Configure the peer

link bypass channel

Configure VXLAN

default

decapsulation

Configure the M-LAG

interface connected to FW

device 4 LACP aggregate

link

Configure the M-LAG

interface connected to FW

device 3 LACP aggregate

link

Incorporation

by controller

Required main process

Optional main process

Required subprocess

Optional subprocess

13

Deployment workflow for spine-border separation scenario

Spine deployment workflow

Server leaf deployment workflow

Underlay basic

settings

Start

Reboot the device

without a startup

configuration file

Configure

hardware resource

parameters

Configure the

management

network

Configure basic

settings for L2VPN

and VXLAN

Configure interfaces

connected to the

leaf

Configure the

underlay routing

protocol

Configure the VTEP

address

Enable the OVSDB

VTEP service

Configure the

overlay BGP

End

Incorporation

by controller

Spine

Required main process

Optional main process

Required subprocess

Optional subprocess

14

Service leaf deployment workflow

Incorporation

by controller

Underlay basic

settings

Start M-LAG

configuration

M-LAG interface

configuration End

Server

Leaf

Reboot the device

without a startup

configuration file

Configure

hardware resource

parameters

Configure the

management

network

Configure basic

settings for L2VPN

and VXLAN

Configure the

underlay routing

protocol

Configure the VTEP

address

Enable the OVSDB

VTEP service

Configure the

overlay BGP

Configure the global

MAC address

Configure interfaces

connected to the

spine

Required main process

Optional main process

Required subprocess

Optional subprocess

Configure the M-

LAG physical

address

Configure the M-

LAG virtual address

Configure M-LAG

System parameters

Configure the M-

LAG peer link

aggregate interface

Configure M-LAG

MAD

Configure the peer

link failover

channel

Configure the peer

link bypass channel

Configure VXLAN

default

decapsulation

Configure the M-LAG

interface connected to

Server 1 LACP

aggregate link

Configure the

physical interface

connected to Server

2 primary and

secondary links

Required main process

Optional main process

Required subprocess

Optional subprocess

Reboot the device

without a startup

configuration file

Configure

hardware resource

parameters

Configure the

management

network

Configure basic

settings for L2VPN

and VXLAN

Configure the

underlay routing

protocol

Configure the VTEP

address

Enable the OVSDB

VTEP service

Configure the

overlay BGP

Configure the global

MAC address

Configure interfaces

connected to the

spine

Configure the M-

LAG physical

address

Configure the M-

LAG virtual address

Configure M-LAG

System parameters

Configure the M-

LAG peer link

aggregate interface

Configure M-LAG

MAD

Configure the peer

link failover

channel

Configure the peer

link bypass channel

Configure VXLAN

default

decapsulation

Configure the M-LAG

interface connected to

FW device 4 LACP

aggregate link

Configure the M-LAG

interface connected to

FW device 3 LACP

aggregate link

Incorporation

by controller

Underlay basic

settings

Start M-LAG

configuration

M-LAG interface

configuration End

Service

Leaf

15

Border deployment workflow

Procedure (spine-border integration scenario)

Note: As a best practice, use OSPF or IS-IS as the underlay routing protocol. If you need to

configure EBGP, contact Technical Support. #

Configure Spine Border 1

Reboot the device without a startup configuration file

<spine-border1> reset saved-configuration

The saved configuration file will be erased. Are you sure? [Y/N]: y

Configuration file in flash: is being cleared.

Please wait…

Mainboard:

Configuration file is cleared.

<spine-border1> reboot force

Configure hardware resource parameters

CAUTION:

After configuring the hardware resource parameters, reboot the device to make the configuration

take effect.

The hardware resource configuration commands vary by switch. Details are as follows:

Configure the M-

LAG interface

connected to LB

Configure the M-

LAG interface

connected to FW

Configure the M-LAG

interface connected to

the external LACP

aggregate link

Incorporation

by controller

Underlay basic

settings

Start M-LAG

configuration

M-LAG interface

configuration EndBorder

Required main process

Optional main process

Required subprocess

Optional subprocess

Reboot the device

without a startup

configuration file

Configure

hardware resource

parameters

Configure the

management

network

Configure basic

settings for L2VPN

and VXLAN

Configure the

underlay routing

protocol

Configure the VTEP

address

Enable the OVSDB

VTEP service

Configure the

overlay BGP

Configure the global

MAC address

Configure interfaces

connected to the

spine

Configure the M-

LAG physical

address

Configure the M-

LAG virtual address

Configure M-LAG

System parameters

Configure the M-

LAG peer link

aggregate interface

Configure M-LAG

MAD

Configure the peer

link failover

channel

Configure the peer

link bypass channel

Configure VXLAN

default

decapsulation

16

12900E Type X Fabric Module

[spine-border1] hardware-resource tcam normal

[spine-border1] hardware-resource routing-mode ipv6-128

[spine-border1] hardware-resource vxlan l3gw

5944/5945

[spine-border1] hardware-resource switch-mode DUAL-STACK

[spine-border1] hardware-resource routing-mode ipv6-128

[spine-border1] hardware-resource vxlan l3gw

Configure the management network

1. Configure the management VPN. In this example, the VPN instance name is mgmt.

[spine-border1] ip vpn-instance mgmt

2. Configure the default route of the management network. The next hop of the default route is

the gateway IP address on the management switch.

[spine-border1] ip route-static vpn-instance mgmt 0.0.0.0 0 192.168.11.1

3. Configure the management port.

[spine-border1] interface M-GigabitEthernet0/0/0

[spine-border1-M-GigabitEthernet0/0/0] ip binding vpn-instance mgmt

[spine-border1-M-GigabitEthernet0/0/0] ip address 192.168.11.2 255.255.255.0

[spine-border1-M-GigabitEthernet0/0/0] quit

4. Configure a management user. In this example, the username is admin and the password is

Qwert@1234. The password must contain at least two of the following character types: digits,

upper-case letters, lower-case letters, and special characters.

[spine-border1] local-user admin class manage

[spine-border1-luser-manage-admin] password simple Qwert@1234

[spine-border1-luser-manage-admin] service-type https ssh

[spine-border1-luser-manage-admin] authorization-attribute user-role network-admin

[spine-border1-luser-manage-admin] authorization-attribute user-role

network-operator

[spine-border1-luser-manage-admin] quit

5. Configure VTY.

[spine-border1] line vty 0 63

[spine-border1-line-vty0-63] authentication-mode scheme

[spine-border1-line-vty0-63] user-role network-admin

[spine-border1-line-vty0-63] user-role network-operator

[spine-border1-line-vty0-63] quit

6. Configure NETCONF.

[spine-border1] netconf soap https enable

[spine-border1] netconf ssh server enable

7. Enable SSH.

[spine-border1] ssh server enable

8. Configure NTP. This procedure is required if there is an NTP server in the network. Take NTP

server IP 192.168.10.101 as an example.

[spine-border1] ntp-service enable

[spine-border1] ntp-service unicast-server 192.168.10.101 vpn-instance mgmt

9. Configure SNMP.

[spine-border1] snmp-agent

[spine-border1] snmp-agent community write private

[spine-border1] snmp-agent community read public

Page is loading ...

Aruba JL849AAE Configuration Guide

This manual is also suitable for

Aruba JL849AAE Configuration Guide

Related papers

Other documents