Lifetime 60215 Owner's manual

7/16" (11 mm) 1/2" (13 mm) 3/8" (10 mm), 7/16" (11 mm),

1/2" (13 mm)

Icon Legend...............................3

Warnings & Notices.....................4

Parts Identiﬁ er............................5

Box Assembly.............................6

Lid Assembly............................12

Additional Warnings..................22

Cleaning & Care........................23

Registration............................24

Warranty..................................25

Import Information...................27

TOOLS REQUIRED TABLE OF CONTENTS

BEFORE ASSEMBLY:

• Assemble on a level surface

• 2+ people are recommended for setup

ASSEMBLY INSTRUCTIONS

MODEL #60091

150-GALLON (567.8 L)

DECK BOX

MODEL 60215

FOR DOMESTIC USE ONLY!

IMPORTANT, RETAIN FOR FUTURE REFERENCE: READ CAREFULLY.

Ḕ㕮䈯Ə寍妨䬓桜˛

CONTACT LIFETIME CUSTOMER SERVICE:

Call: 1-800-225-3865

7:00 am–5:00 pm (Monday–Friday) MST

and 9:00 am–1:00 pm Saturday MST

Live Chat: www.lifetime.com

(click on “LIVE CHAT” tab)

Video Instructions: www.youtube.com/lifetimeproducts

QUESTIONS?

MODEL# AND PRODUCT ID (you will need both when contacting us)

Model Number: 60215

Product ID:

ⲣ‵ 䖬⸓

֣߶ॐ۞

孍␱᷵态␱

னўજӰ

䮘Ἲ䴫壄

䮘䚽䴫壄

昫⊇孍␱

㷬㳨᷵ῄⅢ

㳏ⅳ

崏ῄ

忂⏊Ὲざ

ᶃ攎⩴䏦濊

悋堿媲㓌濣媵ẛ䐗ṙ⫄㘣⊀仁Ʋ媵ᶒ䶄擃媹Ʋ

/LIHWLPH₏䉐䮘宥守❁⛡˚俷䔏˛ㇸồ⊂㰩✏ᷴ⽘

⒴崏憶䙫ガ↜ᷲƏὦ享墬Ⱔ⏖僤✗䭧⌼˚㗺堳˛⥩

㞃わ怮∗⛗暥Əㇸồ⣮㛰⏖㎷ᾂ⸕⊐䙫ⷌ⅞Ɲ

• ◦㫲ⴱ◮映᳈䶂垃㜊⨎Ʋ

• ᵰ⊉ⳬⅧ

⭰墬曧奨ḑạ˚亍⯶㗝⭳ㇷ

For English, see page 1.

⩇垃媲㓌

MODEL #60091

⅞ᶏ∅

ὦ䄧䩯

ᵥ⍿♉⊵

7/16" (11 mm) 1/2" (13 mm) 3/8" (10 mm), 7/16" (11 mm),

1/2" (13 mm)

伒䮹/,)(7,0(⩠ヵ㗋⅟徦濣

䏳媛濣

㒴撲㒧᳈ħ᳉∆濑⌦Ჾħ⌦ᵒ濒

ᶣ⊈⌦󰜬㒴撲㒧᳈ħ᳉∆

∱㔀伈⟧濣ZZZOLIHWLPHFRP

煾⎦≌ŵ屈㖪ṤⰇŶ恚棊⎲煿

墄杏㇅⪺濣ZZZ\RXWXEHFRPOLIHWLPHSURGXFWV

䑏撬濨

ᵥ⍿♉⊵⍊䷔⊵Ƌ倻仃ㇸồ㗝Əわ曧奨富Ὲざƌ

Ỹ┒⟜⑈熐60215

Ỹ┒佧⑈熐

• Indicates the parts to be used for a section.

• 墹䦋䶕央嫃愹὎㚓㊑村䛕愹὇˛

• Indicates special heed should be taken when reading.

• 墹䦋❹昂寑㚓村䋊≶䖪ㅠ˛

• Indicates the hardware to be used for a section.

• 墹䦋䶕央嫃愹὎㚓㊑村䛕ụ戢⚹⇈˛

• Indicates the tools to be used for a section.

• 墹䦋䶕央嫃愹὎㚓㊑村䛕⸶⇈˛

• Indicates no hardware required for a speciﬁ c page.

• 墹䦋嫃䋊⯫桒枳䛕䶕央Ṟ村姒Ὄᾦ愹὇˛

• Indicates no parts required for a speciﬁ c section.

• 墹䦋䶕央嫃䋊⯫愹὎㚓Ṟ村姒Ὄᾦ愹὇˛

• Indicates to use/not to use an electric drill for a speciﬁ c step.

• 墹䦋嫃䋊⯫㮶檰ῐ䕹Ṟῐ䕹杌抗˛

ICON LEGEND /

• These Nuts are centerlock nuts. They are designed to be tight; therefore, they will be harder to tighten. Tighten until ﬂ ush

with the metal or plastic.

• 恪Ử堋⺎䄋Ṿ〔揧⯫堋⺎˛⯔⁢㘹❹巈丛❋ᾭ䕹熑✱㮵熂⯔⁢❹㕁丛㚓村姒䕹⋬˛

1218818 6/1/2021

English:

• Failure to follow these warnings may result in serious injury or property damage and will void warranty.

• To ensure safety, do not attempt to assemble this product without following the instructions carefully.

• Assemble on level a level surface.

• Be aware that plastic pieces can be damaged by overtightening the screws. To avoid damage, we strongly recommend

the use of a drill with a low torque setting. A #2 Phillips screwdriver may also be used.

• Two capable adults are required for assembly.

• All who participate in the assembly process should wear safety glasses throughout the assembly.

• Do not use or store hot objects near the product.

• Proper and complete assembly are essential to reduce the risk of accident or injury.

• Lifetime® storage boxes are made to protect the things you value. This includes features such as a water-resistant

enclosures that help keep your things protected from rain, snow, and the elements. It should be noted that Lifetime

storage boxes are not waterproof. The storage boxes are not meant for uses other than indoor and outdoor storage.

Lifetime® storage boxes are designed to last through the rigors of every-day life—built for strength and durability.

• Most injuries are caused by misuse and/or not following instructions.

• Other warnings may be viewed towards the end of this manual.

Зݧ

ȕ Јଇ؋ૠоਖ਼ठՔৗج৩࣐ېДଜՈѮͧуռܤ֯ٶ୎ܯۋࣻܯૼۉએуܤס澞բݿ૟ذૼۉҐ֠סݝ澞

ȕ НгगҐ㕭ࣩ،ҵͧ੻Ԓعੰ֧Јଇڱ،ੇ੹ރࣩ㖊ӐЇ১ਸ਼،ੇ澞

ȕ ੻֧ؠ㦁ࣩٴ֩Іૡਸ਼ঐੇ澞

ȕ ࡉڿͧ૚څଶॻ夊БذѪૼۉ⸎ݪ଑ѝऔ੆澞Нгଈұऔ੆ͧۊњڟ䎾ڎ੠࣐҄ࣔବٶ੦঴НѹܛѸ澞ࣩ6NORROVY

夊БӡЬޥՔৗ੃࣐҄Ӱ澞

ȕ ޯ،ੇ২ش୻ੌГգޥԂࣩۉٵъ澞

ȕ ےޥԿԅ،ੇࣩъճڶஏҵस҂٪،ҵ୔۵ऄ୅澞

ȕ ੻Ԓ֧ޯуռଡ଼૝࣐҄ۋ؁ݚளࡴࢢѼ澞

ȕ 㔵ڡࣩͧ؎ҵࣩ،ੇৗёׁޯІӖشу࣏жݜոૼۉՈѮࣩ஝୤澞

ȕ 2OLKZOSKoҤࢢॣОੌ࣐иҐ؁㕭ࣩଜੌࢢռ澞؈ࣩ۱ࠫࢤ㓬ৗ֧Ї୶ͧЇ୷јՂҾ؈▁оࠩҗҪॹݿફҐ۵Ҁ࣐澞

୻ੌࡉڿͧ2OLKZOSKoࣩҤࢢॣЈҿה୔ࠫԄৗ澞Ҥࢢॣୣг؛Ӄ澝؛טࣩҤࢢטЈ૯࣐иҾ؈࣐૷澞2OLKZOSKoҤ

ࢢॣ䰠۩ֲ֠ոূ࣐ࣩӫੀНݺٮ࣏ࡕ੦ਗ਼࣐҄澞

ȕ ל଑ӢࣩՈѮފ֛Нହ੷࣐҄ۋী࠻ޥଇ࢑੹ރڕફࣩ澞

ȕ Ҿ؈ࣩ▁оਖ਼ठՔৗѪ֧ޯەӅࣩޮـऀӰ澞

WARNINGS & NOTICES / ਖ਼ղЉૹղ

EZC

Metal Parts / 憸ⱅ惏ờ

Plastic Parts / ⠸僝惏ờ

Hardware Bag / ṻ憸愴ờ⋬

PARTS REQUIRED / ヾ斾徦ᶴ

HARDWARE REQUIRED / ヾ斾ᵒ悏怋ᶴ

PARTS IDENTIFIER / 徦ᶴ媄⃩

AMZ (x1) AGN (x1)

AGY (x1)ANA (x1)

ANC (x1)

AND (x1)

EZA (x1)

DRE (x1)

BET (x4)

AAO (x4)

BEP (x2)

AKF (x2) DRD (x1)

AMZ (x1) AGN (x1)

AGY (x1)ANA (x1)

ANC (x1)

ADW (x26)

Plastic Parts / ⠸僝惏ờ

Metal Parts / 憸ⱅ惏ờ

Hardware Bag / Sac de quincaillerie / Bolsa de herraje

TOOLS REQUIRED / 斾堿䕂ⲣ‵

PARTS REQUIRED / ヾ斾徦ᶴ

HARDWARE REQUIRED / ヾ斾ᵒ悏怋ᶴ

BOX ASSEMBLY / 䩯ḑ⩇垃

DRC (x1) ADJ (x1)

DRD (x1)

7/16" (11 mm)

EZC

TOOLS AND HARDWARE REQUIRED / 曧奨䙫ⷌ⅞⑳ṻ憸愴ờ

X SECTION 1 (CONTINUED) / 㨣楢Ჾ (䶫)

ANC

ANA

1.2

• Insert the six (6) tabs at the bottom of the Rear Panel (ANA) into the six (6) slots in the Floor Panel (ANC).

•⯠漷⋌映㘽(ANA)⹼惏䙫ḑ⍈㉊∗⹼㝦(ANC) ᷱ䙫ḑ⇠㧤⏵㎹⅌˛

• Slide the Rear Panel to the left until it stops.

⏸ⷍ㺸⊏⏵杉㝦䛛凚⍈㉊⭳⅏㉊⅌⇠㧤

1.1

TOOLS AND HARDWARE REQUIRED / 曧奨䙫ⷌ⅞⑳ṻ憸愴ờ

X SECTION 1 (CONTINUED) / 㨣楢Ჾ (䶫)

AMZ

AGN

1.3 • Repeat steps 1.1–1.2 for the Front Panel (AMZ).

悅䏦㨣楢䕂㑷㮓⩇垃ℋ映㘽(AMZ)Ʋ

1.4 • Fold over the ends of the Left Side Panel (AGN), and insert the tabs at the bottom of the Panel into the slots in the

Floor Panel. You should hear the tabs snap into place. The notch goes at the back.

• ⥩⛥⼖㉿Ⲥ映㘽(AGN)ḋ䫖⏵⯭⅝㎹⅌⹼㝦ᷱ䙫⇠㧤˛㊐‣㒴⽦⊭ᶣ⋪⃮∟ㄡㄡ‣⊏₸䕂㳃俄➮暱Ʋⷭㅖ䕂₷

⊡◦映㘽⁃ṥƲ

• Notch

• ⇠⏊

TOOLS AND HARDWARE REQUIRED / 曧奨䙫ⷌ⅞⑳ṻ憸愴ờ

X SECTION 1 (CONTINUED) / 㨣楢Ჾ (䶫)

1.5

1.6

• Secure the Left Side Panel to the Rear Panel

with four (4) Screws (ADW). Then, secure the Panel

to Front Panel using four (4) more Screws (ADW).

⥩⛥⇭−ὦ䔏桾噸᳛(ADW)⯭ⷍ杉㝦⛡⮁凚∴

⏵杉㝦

ADW (x16)

• Repeat steps 1.4–1.5 for the right side.

悅䏦㨣楢䕂㑷㮓⩇垃䩯ḑ⊱ṥ

ADW

TOOLS AND HARDWARE REQUIRED / 曧奨䙫ⷌ⅞⑳ṻ憸愴ờ

X SECTION 1 (CONTINUED) / 㨣楢Ჾ (䶫)

ADW (x10)

1.7

1.8

• Insert a Screw (ADW) straight through each of the ﬁve (5) tabs on the Left Side Panel.

⥩⛥✏ⷍ杉㝦䙫㮶ḑ⍈㉊ᷱ⏫擨⅌ᷧ㞁噸᳛ (ADW)Ə⅘㞁

• Repeat step 1.8 for the Right Side Panel.

悅䏦㨣楢䕂㑷㮓⩇垃⊱ṥ映㘽

ADW

ADW ADW

TOOLS AND HARDWARE REQUIRED / 曧奨䙫ⷌ⅞⑳ṻ憸愴ờ

X SECTION 1 (CONTINUED) / 㨣楢Ჾ (䶫)

• Attach the Locking Tab (DRD) to the Front Panel using the hadware indicated.

ὦ䔏⛥䤡䙫ṻ憸愴ờ⯭᳉掿淹(DRD)⭰墬∗∴杉㝦ᷱ˛

DRC (x1)

DRC

DRD

ADJ

ADJ (x1)

7/16"

(11 mm)

1.9

AND (x1)

7/16", 1/2"

(11 mm, 13 mm)

7/16"

(11 mm)

1/2"

(13 mm)

EZA (x1)

Metal Parts / 憸ⱅ惏ờ Plastic Parts / ⠸僝惏ờ

Hardware Bag / ṻ憸愴ờ⋬

TOOLS REQUIRED / 斾堿䕂ⲣ‵

PARTS REQUIRED / ヾ斾徦ᶴ

HARDWARE REQUIRED /斾堿䕂ᵒ悏怋ᶴ

LID ASSEMBLY / 䩯䖔⩇垃

BES (x6)

DRE (x1)

AAB (x6)

BET (x4)

BCK (x6)

AAO (x4)

BEP (x2)

DRF (x4)

AKF (x2)

EZC

NO TOOLS AND HARDWARE REQUIRED / 㘱村ⷌ⅞⑳ṻ憸愴ờ

X SECTION 2 (CONTINUED) / 㨣楢ᵊ (䶫)

• Attach the Lid Locking Tab (DRE) to the Lid Support (EZA) using the hardware indicated.

ὦ䔏⛥䤡䙫ṻ憸愴ờ⭰墬䩯䖔掿淹(DRE) ∗䩯䖔㏭㍏㘄 (EZA)ᷱ˛

• These Nuts (AAB) are centerlock nuts. They are

designed to be tight; therfore, they will be harder to

tighten. Continue turning them until they are ﬂush with

the Lid Locking Tab (DRE).

• 忀Ẃ垡⸤(AAB)ḡḔ⾪擨⮁垡⸤˛⭪ồ㗏✏嵞䶱

⛡ὃ䔏ƞ⛇㭋Ə⭪ồ✏㋎䴎㗝曧奨䔏⊂˛寞㋨仔

䔏⊂㋎䴎䛛凚⅝᷵䮘䚽擨漢

(DRE) 漷⹚˛

Notch / ⇠⏊

BES (x2)

BES

DRE (x1)

DRE

EZA

AAB (x2)

AAB

7/16"

(11 mm)

7/16"

(11 mm)

2.1

NO TOOLS AND HARDWARE REQUIRED / 㘱村ⷌ⅞⑳ṻ憸愴ờ

X SECTION 2 (CONTINUED) / 㨣楢ᵊ (䶫)

AND

2.2

• Rotate the Lid Support downward, and insert the opposite end into the slot in the front, right corner of the Lid.

⥩⛥⏸ᷲ㋰⍲䮘䚽㔖㑸㜭䙫⏍ᷧ䫖ὦ⅝㎹⅌䩯䖔(AND)∴⏚当妹䙫⇠㧤˛

2.3

• Insert an end of the Lid Support into the slot in the front corner of the Lid (AND).

• ⥩⛥⯭䮘䚽㔖㑸㜭䙫ᷧ䫖㎹⅌䩯䖔(AND)∴ᷧ䫖当妹䙫⇠㧤˛

Front / ∴

Rear / ⏵

Notch / ⇠⏊

NO TOOLS AND HARDWARE REQUIRED / 㘱村ⷌ⅞⑳ṻ憸愴ờ

X SECTION 2 (CONTINUED) / 㨣楢ᵊ (䶫)

• Notches at the rear of the Lid.

• ⇠⏊ἴṵ䮘䚽⏵ᾎ˛

• Use a drill to attach the Lid Support to the Lid using the hardware indicated. Do not overtighten.

䔏䔜⊏垡Ḅ⇧ὦ䔏⛥䤡ṻ憸愴ờ⭰墬䮘䚽㔖㑸㜭∗䮘䚽ᷱ˛媵↽庅ᵌ掿䯥噸㛑˛

• The Hinge (BEP) goes together this way for the left side of the Lid.

⥩⛥享墬䮘䚽Ⲥṥ掮掼(BEP)˛

BEP

BET

AAO

2.4

2.5

BCK

BCK BCK BCK BCK

BCK (x6)

BET (x2) AAO (x2)

1/2"

(13 mm)

1/2"

(13 mm)

Front / ∴

NO TOOLS AND HARDWARE REQUIRED / 㘱村ⷌ⅞⑳ṻ憸愴ờ

X SECTION 2 (CONTINUED) / 㨣楢ᵊ (䶫)

• By design, the Screws (DRF) are slightly larger than the holes; therefore, it is easier to perform this step using a

socket wrench. Do not overtighten.

• 愴⤾䙫噸㛑(DRF)宥守⽾䕌⤎ṵ垡Ḅ⬻Əḡṭ㖠ᾦわ䙫⭰墬Ə㜓㭌檋⻡宕ὦ䔏⤾䬹㉚㈲˛媵↽庅ᵌ掿䯥噸㛑Ʋ

2.6

2.7

• Insert the left Hinge into the slot and rotate it downard as shown. The Ball Studs face toward the inside.

• ⥩⛥㎹⅌Ⲥṥ掮掼(BEP)∗䮘䚽ᷱ䙫⇠㧤⹝⏸ᷲ㋰⍲˛䋁⟲噸㛑映⋏⁃ṥƲ

DRF (x2)

DRF

NO TOOLS AND HARDWARE REQUIRED / 㘱村ⷌ⅞⑳ṻ憸愴ờ

X SECTION 2 (CONTINUED) / 㨣楢ᵊ (䶫)

1/2"

(13 mm)

1/2"

(13 mm)

• The Hinge (BEP) goes together this way for the right side of the Lid.

• ⥩⛥享墬䮘䚽⊱ṥ掮掼 (BEP)˛

2.8

2.9 • Insert the right Hinge as you did the left. The Ball Studs face toward the inside.

• 憮䔏⭰墬ⷍᾎ擗擥䙫㖠㲼㎹⅌⏚ᾎ擗擥∗䮘䚽ᷱ˛䋁⟲噸㛑映⋏⁃ṥƲ

BEP

BET

AAO

BET (x2) AAO (x2)

NO TOOLS AND HARDWARE REQUIRED / 㘱村ⷌ⅞⑳ṻ憸愴ờ

X SECTION 2 (CONTINUED) / 㨣楢ᵊ (䶫)

• By design, the Screws (DRF) are slightly larger than the holes; therefore, it is easier to perform this step using a

socket wrench. Do not overtighten.

• 愴⤾䙫噸㛑(DRF)宥守⽾䕌⤎ṵ垡Ḅ⬻Əḡṭ㖠ᾦわ䙫⭰墬Ə㜓㭌檋⻡宕ὦ䔏⤾䬹㉚㈲˛媵↽庅ᵌ掿䯥噸

㛑Ʋ

• Rotate the hinges to 90° angles as shown.

• ⥩⛥䤡㖲当擗擥ὦ⅝⤠妹ㇷ˛

2.10

2.11

DRF (x2)

DRF DRF

NO TOOLS AND HARDWARE REQUIRED / 㘱村ⷌ⅞⑳ṻ憸愴ờ

X SECTION 2 (CONTINUED) / 㨣楢ᵊ (䶫)

2.12 • Set the Hinges down onto the Rear Panel as shown.

• ⥩⛥䤡ᷲ㔥擗擥∗⏵杉㝦ᷱ˛

NO TOOLS AND HARDWARE REQUIRED / 㘱村ⷌ⅞⑳ṻ憸愴ờ

X SECTION 2 (CONTINUED) / 㨣楢ᵊ (䶫)

BES (x4)

BES

7/16"

(11 mm)

7/16"

(11 mm)

AAB (x4)

2.13 • Secure the Left Hinge to the Side Panel using the hardware provided. Repeat the last step for the right Hinge.

• ὦ䔏⛥䤡䙫ṻ憸愴ờ⭰墬ⷍᾎ擗擥˛悋⟋㗪㨣楢⩇垃⊱ṥ掮掼Ʋ

AAB AAB

Page is loading ...

Lifetime 60215 Owner's manual

Related papers

Other documents