Reese 118244 Installation guide

Reese
Brand
Reese
Model
118244
Type
Installation guide

Reese 118244 is a tow plug adapter, enabling a secure connection between a tow vehicle and a trailer. It conveniently plugs into the tow vehicle's trailer harness connector, ensuring a reliable electrical connection for lighting and other essential functions. With a rating of 7.5 amps per circuit, this adapter allows for the safe and efficient operation of trailer lights, turn signals, and brake lights.

Reese 118244 is a tow plug adapter, enabling a secure connection between a tow vehicle and a trailer. It conveniently plugs into the tow vehicle's trailer harness connector, ensuring a reliable electrical connection for lighting and other essential functions. With a rating of 7.5 amps per circuit, this adapter allows for the safe and efficient operation of trailer lights, turn signals, and brake lights.

ENGLISH
1. Locate tow vehicle’s trailer harness
connector. This harness is located under the
vehicle, behind the rear bumper, on the
passenger’s side of the vehicle.
2. Remove protective cap from connector.
Check to see that the mating surfaces of the
connectors are free of dirt and clean if
necessary.
3. Connect the Tow Plug Adapter end to the
vehicle’s connector. Be sure that the Tow
Plug is fully inserted with locking tabs in
place.
4. Test the installation with a test light or a
trailer.
This unit is rated for 7.5 amps per circuit.
ESPAÑOL
1. Localice el conector para el arnés del
remolque en el vehículo remolcador. Este
arnés está situado debajo del vehículo, detrás
del parachoques trasero en el lado del
pasajero.
2. Retire la tapa protectora del conector.
Revise que las superficies correspondientes de
los conectores estén libres de suciedad y
límpielas si es necesario.
3. Conecte el extremo del adaptador del
enchufe de arrastre al conector del vehículo.
Asegúrese de que el enchufe de arrastre esté
completamente insertado y con las pestañas
de seguridad en su sitio.
4. Revise la instalación con una luz de
prueba o con un remolque.
Esta unidad es clasificada para 7.5 amperios
por el circuito.
FRANÇAIS
1. Repérez le connecteur du faisceau de
remorque sur le véhicule tracteur. I1 se
trouve sous le véhicule, derrière le
pare-chocs arrière, côté passager.
2. Retirez l'embout de protection du
connecteur. Vérifiez que les surfaces de
contact des connecteurs sont propres et
nettoyez-les si nécessaire.
3. Branchez l'adaptateur de fiche de
remorquage dans le connecteur du véhicule.
Assurez-vous que la fiche de remorquage est
complètement insérée et que les attaches de
verrouillage sont bien en place.
4. Testez l'installation à l'aide d'une
lampe-témoin ou d'une remorque d'essai.
Cette inité est évaluéé pour 7.5 ampères
par circuit.
Installation instructions
Instructions d’installation
Instrucciones de instalación
18244-037 4/7/03
  • Page 1 1

Reese 118244 Installation guide

Reese
Brand
Reese
Model
118244
Type
Installation guide

Reese 118244 is a tow plug adapter, enabling a secure connection between a tow vehicle and a trailer. It conveniently plugs into the tow vehicle's trailer harness connector, ensuring a reliable electrical connection for lighting and other essential functions. With a rating of 7.5 amps per circuit, this adapter allows for the safe and efficient operation of trailer lights, turn signals, and brake lights.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages

Related papers