Hunter Fan 50091 Owner's manual

Brand: Hunter Fan

Model: 50091

Type: Owner's manual

This manual is also suitable for

Hunter Fan 50091 is the quietest ceiling fan you can buy, featuring a powerful motor and innovative blade design that gives you increased airflow while running whisper-quiet. It can be used to cool you down in the summer or circulate warm air in the winter.

www.ventiladoreshunter.com.br

MD507-01 • 09/29/14 • © Hunter Fan Company

ENGLISH

Important Instructions: Keep Instructions for future use

www.hunterfan.com.br

MD507-01 • 09/29/14 • © Hunter Fan Company

PAG E

30 inches

7 feet

PAG E

What to Expect with

Your Installation

Ceiling Bracket

Ladder

PAG E

Tools Needed

Table of Contents

Mounting Options

PAG E

Wiring CanopyDownrodPreparation

PAG E

Maintenance &

Cleaning

Troubleshooting

PAG E

Warranty Statement

PAG E

Switch Housing

PAG E

No Light Kit Option

PAG E

Light Kit Option

Blades

PAG E

Congratulations on purchasing your new Hunter® ceiling

fan! It will provide comfort and performance in your home or

ofce for many years. This installation and operation manual

contains complete instructions for installing and operating

your fan.

We are proud of our work and appreciate the opportunity to

supply you with the best ceiling fan available anywhere in

the world.

www.hunterfan.com.br

MD507-01 • 09/29/14 • © Hunter Fan Company

What to Expect with Your Installation

w.1 - To reduce the risk of re, electrical shock, or personal injury,

mount fan directly from building structure and/or an outlet

box marked acceptable for fan support of 31.8 kg and use the

mounting screws provided with the outlet box.

w.2 - To avoid possible electrical shock, before installing or

servicing your fan, disconnect the power by turning off the circuit

breakers to the outlet box and associated wall switch location. If

you cannot lock the circuit breakers in the off position, securely

fasten a prominent warning device, such as a tag, to the service

panel.

w.3 - To reduce the risk of re, electrical shock, or motor damage,

use only Hunter Solid State Speed Controls.

w.4 - To reduce the risk of personal injury, do not bend the blade

brackets when installing the blade brackets, balancing the blades, or

cleaning the fan. Do not insert foreign objects in between rotating fan

blades.

w.5 - This appliance is not intended for use by persons (including

children) with reduced physical, sensory or mental capabilities, or

people with a lack of experience and knowledge, unless they have

received instructions regarding the use of the device or under the

supervision of a person responsible for their safety.

w.6 - It is recommended that children be supervised to ensure that

they are not using the appliance improperly

c.1 - All wiring must be in accordance with national and local

electrical codes ANSI/NFPA 70. If you are unfamiliar with wiring, use a

qualied electrician.

c.2 - Use only Hunter replacement parts.

You may need a

friend to help you.

Check box to see

fan weight

Assess location

0,50 meters

from blade tip to

nearest wall or

obstruction

2,3 meters

from bottom

edge of blade to

the oor

Know your wiring

If you are unfamiliar

with wiring, use a

qualied electrician.

This product conforms to UL Standard 507.

WARNINGS

CAUTIONS

Must be able to

secure the fan to

building structure or

fan-rated outlet box.

Do not use a plastic

outlet box.

Select a downrod length

Standard Downrod

for ceilings 2,4 -3 meters high

Shorter Downrod

for fans installed close to ceiling

Longer Downrod

for ceilings 3 meters or higher

Use ONLY Hunter

Ceiling Fan branded

accessory light kits.

www.hunterfan.com.br

Tools Needed

Ladder

Pliers Wire Strippers

Screwdrivers

Power Drill

(optional)

3,5 mm Drill

Bit (optional)

8 mm Drill Bit

(optional)

If mounting to a support structure, you

will also need these tools.

Hammer

(optional)

9 mm Wrench

MD507-01 • 09/29/14 • © Hunter Fan Company

www.hunterfan.com.br

MD507-01 • 09/29/14 • © Hunter Fan Company

Hang your fan by a standard downrod

(included) or use a shorter downrod (sold

separately) for Low-Prole Mounting.

Mounting Options

Note: Do not hang the fan from a

ceiling that is angled greater than 34°

Support

Structure

Ceiling

Outlet Box

(required)

Angled

Mounting

Style

Standard

Mounting

Style

Support

Structure

Ceiling

Outlet Box

(required)

Carefully choose the installation location

that allows for optimal air ow.

The support structure must be able to support 5

times the weight of the fan. The weight of the fan is

located on the product packaging.

You will need a longer downrod (sold

separately) to hang the fan from a

vaulted or angled ceiling.

If you have a at ceiling: If you have an angled ceiling:

www.hunterfan.com.br

MD507-01 • 09/29/14 • © Hunter Fan Company

Ceiling Bracket

OFF

Refer to warning w.1 on pg. 2

To avoid possible electrical shock, before installing your fan, disconnect the

power by turning off the circuit breakers to the outlet box associated with the

wall switch location.

Turn Power

Remove all four mounting isolators.

Align the tapered mounting holes in the

ceiling plate with the holes in the ceiling

bracket. Install the four ceiling plate

screws found in the hardware bag and

secure with the ange nuts using an 9 mm

wrench. Hold the ceiling bracket assembly

up to the outlet box and mark the screw

locations. To mount to support structure,

also mark the ceiling for drilling pilot holes.

Install the ceiling plate gasket onto the

ceiling plate. The four holes in the ceiling

plate should lineup with the four posts in

the gasket.

Tapered

Mounting

Holes

Ceiling

Plate

Gasket

Post

Ceiling

Plate

Ceiling

Plate

Flange

Nuts

Mounting

Isolator

Ceiling

Bracket

Ceiling Plate

Screws

For angled ceilings, point

opening toward peak.

www.hunterfan.com.br

MD507-01 • 09/29/14 • © Hunter Fan Company

Ceiling Bracket

Use wood screws

(included) when securing

to support structure with

approved electrical outlet

box. Drill 3,5 mm pilot

holes in support structure

to aid in securing ceiling

bracket with hardware

found in the hardware

bag.

Use machine screws

(provided with outlet

box) when securing to

existing ceiling fan-rated

outlet box. Make sure

it is securely installed

and is acceptable for fan

support of 31,8 kg or less.

Note: Do not mount ceiling fan

to a plastic outlet box.

Use concrete anchors (included)

when securing to support structure

with approved outlet box in a concrete

ceiling. Drill 8 mm pilot holes in

support structure. Hammer the M6

expansion anchors into the holes until

the ends are ush with the ceiling.

Install the washer, isolator, and nut

found in the hardware bag to

the expansion anchors.

Use the wood screw to poke holes through

the rubber gasket in order to install the

ceiling bracket assembly to your support

structure or ceiling fan-rated outlet box.

www.hunterfan.com.br

Ceiling Bracket (continued)

Preparation

Remove the shipping blocks from the

motor. Save the screws. They will be

needed for blade iron installation.

Note: Some fans will have a shipping

ring instead of shipping blocks. Please

remove the ring and save the screws.

MD507-01 • 09/29/14 • © Hunter Fan Company

www.hunterfan.com.br

MD507-01 • 09/29/14 • © Hunter Fan Company

Downrod

S lide

1 2 3 4 5

678910

Sold Separately

Longer

Downrod

for angled

ceilings or

ceilings 3 m or

higher

Shorter

Downrod

for fans installed

close to ceiling

Standard

Downrod

for ceilings 2,4-3 m

high

Option 1Option 2

Option 3

skip to next page

If you need a different downrod length follow these steps:

Steps 1-5 to remove standard downrod pipe

Steps 6-10 to reassemble with new pipe

Included

(pre-assembled)

Sold Separately

www.hunterfan.com.br

MD507-01 • 09/29/14 • © Hunter Fan Company

20 cm

1 cm

(not to scale)

Remove the pre-installed

setscrew so that the downrod

can be inserted.

Hand tighten the downrod (at

least 4-5 full turns) until it stops.

The wires can be cut,

but leave at least 20 cm

extending from the top of

the downrod.

Downrod (continued)

Tighten the setscrew

with pliers. DO NOT

HAND TIGHTEN.

If the setscrew is not tightened

securely, the fan may fall.

20 cm 1 cm

www.hunterfan.com.br

MD507-01 • 09/29/14 • © Hunter Fan Company

Downrod (continued)

DO NOT PICK THE FAN UP BY THE CANOPY

OR WIRES. Place the downrod ball into the slot

in the ceiling bracket.

Put the wires and downrod through the canopy.

Let the canopy sit loosely on top of the fan.

www.hunterfan.com.br

MD507-01 • 09/29/14 • © Hunter Fan Company

Wiring

Using an orange wire

connector from

the hardware bag,

connect the 3 grounding

wires (green, green/

yellow stripe, or bare

copper) coming from the

ceiling, downrod, and

hanging bracket.

(Grounding)

Green/Yellow

Stripe

Green/Yellow

Stripe

Blue

Brown

(Grounded)

Note: To connect the wires,

hold the bare metal leads

together and place a wire

connector over them, then twist

clockwise until tight.

Using the orange wire

connectors from

the hardware bag, connect

the brown wire (ungrounded)

from the ceiling to the

brown and the black with

white stripe wires from the

fan. Connect the blue wire

(grounded) from the ceiling to

the blue wire from the fan.

Using the orange wire

connectors from

the hardware bag,

connect the blue wire

(grounded) from the

ceiling to the blue wire

from the fan.

Connect the brown wire

(ungrounded) from the

ceiling to the brown wire

from the fan. Connect the

second (ungrounded)

wire from the ceiling to

the black with white stripe

wire from the fan.

Blue

(Ungrounded)

Brown

Black with white stripe

(Grounded)

(Ungrounded)

For Dual Switches

For a Single Switch

Turn the splices upward and push them carefully back through the hanger bracket

into the outlet box. Spread the wires apart, with the grounded wires on one side of

the outlet box and the ungrounded wires on the other side of the outlet box.

Refer to CAUTION c.1 on pg. 2

White Stripe

(Ungrounded)

www.hunterfan.com.br

MD507-01 • 09/29/14 • © Hunter Fan Company

Canopy

Lift the canopy into place so that

the screw holes are aligned.

Position the canopy so that, when

lifted into place, the canopy ts into

the hanging bracket as shown.

Screw

Holes

Insert the two canopy screws

found in the hardware bag.

Note: Fan style may vary.

www.hunterfan.com.br

Blades

Your blades are shielded with Dust Armor® which

is a nanotechnology coating that repels dust. For

cleaning the fan, use soft brushes or cloths to prevent

scratching. Cleaning agents may damage the nishes.

Secure each blade to a blade iron with

screws found in the hardware bag.

Remember the screws that

you kept after removing the

shipping blocks (page 7)? You

need them for this step.

Lightly attach the blade irons to the

motor with the blade iron armature

screws, then securely tighten after both

screws are attached.

Note: You need ten screws to complete

this step. Additional screws might be

found in the hardware bag.

www.hunterfan.com.br

Make sure the upper switch housing is securely

attached to the mounting plate. Failure to properly

secure all 3 assembly screws could result in the switch

housing xture falling.

Switch Housing

Feed the wire plug through the center

hole of the upper switch housing, then

wrap keyhole slots around the screws and

twist counterclockwise.

Align the screw holes in the switch

housing gasket and the motor housing.

Screw two switch housing assembly

screws from the hardware bag halfway

into the motor housing. It does not matter

which two screw holes you choose.

Insert the third screw, found in

the hardware bag, into place and then

tighten all three screws.

www.hunterfan.com.br

Make sure the lower switch housing is securely attached to

the upper switch housing. Failure to properly secure all three

assembly screws could result in the light xture falling.

No Light Kit Option

Connect the plugs from

the upper and lower switch

housings. Make sure to line up

the colored markings on the

connectors.

Attach the pull chain pendant to

the short chain coming from the

switch housing.

Lift the lower switch housing

until its screw holes are aligned

with the screw holes in the upper

switch housing. Install the three

switch housing screws, found in

the hardware bag. Tighten all

three screws.

Hold the lower switch housing

in both hands. Push the plug

button through the cap and into

the lower switch housing.

Plug

Button

Cap

www.hunterfan.com.br

CONGRATUALTIONS!

YOU’RE DONE!

No Light Kit Option (continued) Light Kit Option

Align the screw holes in the gasket with the screw

holes in the lower switch housing and the light kit.

Connect the end of the brown wire from the lower

switch housing to the brown wire from the light kit.

Connect the end of the blue wire from the lower

switch housing to the blue wire from the light kit.

Connect the end of the green with yellow stripe

wire from the lower switch housing to the green

with yellow stripe wire from the light kit. Twist a wire

connector onto the bare wires clockwise until tight.

Lower

Switch

Housing

See page 19 for fan

operation instructions.

www.hunterfan.com.br

Lift the light kit up, tucking the

wires into the hole in the switch

housing. Install the center stem of

the light kit into the lower switch

housing by turning the threaded

rod clockwise into the threaded

hole. Continue turning until

tight. Make sure the light xture

mounting screw holes are aligned.

Light Kit Option (continued)

Threaded

Rod

Lift the lower switch housing

until its screw holes are aligned

with the screw holes in the upper

switch housing. Install the three

switch housing screws, found in

the hardware bag. Tighten all

three screws.

Connect the plugs from

the upper and lower switch

housings. Make sure to line up

the colored markings on the

connectors.

Insert and tighten the two light

xture mounting screws, found

in the hardware bag, through

the light xture, the light xture

gasket and into the switch

housing.

www.hunterfan.com.br

Install a 14W CFL bulb (sold

separately) into the E27 socket.

When necessary, replace with

bulb of same wattage.

CONGRATUALTIONS!

YOU’RE DONE!

Connect the appropriate pull

chain pendant to each of the

short chains coming from the

switch housing and the light

kit The fan pull chain controls

the speed: from high to off. The

light pull chain controls the light

xture: on and off.

Light

Pull

Chain

Fan

Pull

Chain

See next page for fan

operation instructions.

Light Kit Option (continued)

To install the bowl, rst loosen

the thumbscrews. Raise the bowl

to the light xture. Tighten all

thumbscrews securely.

Thumbscrew

Page is loading ...

Hunter Fan 50091 Owner's manual

Brand: Hunter Fan

Model: 50091

Type: Owner's manual

This manual is also suitable for

Download PDF

report

Hunter Fan 50091 Owner's manual

This manual is also suitable for

Hunter Fan 50091 Owner's manual

Related papers

Other documents