Liebherr SBSbs 8673 Premium Owner's manual

Brand: Liebherr

Model: SBSbs 8673 Premium

Type: Owner's manual

Installation instructions

Side-by-Side combinations

20190604

7088146 - 00

SBS(es/bs)

Contents

1 General safety information................................... 2

2 External dimensions of the appliance................. 2

3 Side-by-side assembly.......................................... 2

The manufacturer works constantly on the further development

of all the types and models. Therefore please understand that

we have to reserve the right to make design, equipment and

technical modifications.

To get to know all the benefits of your new appliance, please

read the information contained in these instructions carefully.

The instructions apply to several models. Differences may

occur. Text relating only to specific appliances is marked with

an asterisk (*).

Instructions for action are marked with a

, the results of

action are marked with a .

1 General safety information

The socket must be easily accessible so that

the appliance can be quickly disconnected

from the supply in an emergency. It must be

outside the area of the rear of the appliance.

DANGER identifies a situation involving direct

danger which, if not obviated, may

result in death or severe bodily

injury.

WARNING identifies a dangerous situation

which, if not obviated, may result in

death or severe bodily injury.

CAUTION identifies a dangerous situation

which, if not obviated, may result in

minor or medium bodily injury.

NOTICE identifies a dangerous situation

which, if not obviated, may result in

damage to property.

Note identifies useful information and tips.

2 External dimensions of the

appliance

Fig. 1

Model a

[mm]

g [°] h

[mm]

SBS(e

s/bs)

86..,

SBSes

84..

1210 1850

600

665

1185

1752 115 35

If you are using wall spacers, add 15 mm to the dimensions.

With the door open, the dimensions apply to an opening angle

of 115 °. Distances vary depending on the opening angle.

3 Side-by-side assembly

Install the freezer or the appliance with freezer compartment on

the left as viewed from the front. These appliances have a side-

wall heating on the right-hand side to prevent the formation of

condensation.

All the assembly components are supplied with the appliance.

Fitting parts in the accessory kit.

General safety information

2 * Depending on model and options

Fig. 2

Fitting parts, supplied in the appliance.

Fig. 3

Fig. 4

Ensure that the following tools are to hand:

SW 23/10 open-ended wrench (supplied)

Torx® 25/20/15 screwdriver

Power screwdriver

Spirit level

Information for moving the combined appliance:

Before assembling the appliances, site them as closely as

possible to the final position.

For proper assembly, the appliances must however be

accessible on all sides.

When moving the appliances after assembly, always grasp

the front outside corners. Never press your knee against the

side walls or door.

The combined appliance is easiest to shift diagonally by

moving the left and right corner alternately.

Once the combined appliance is exactly in front of the aper-

ture, push it straight in.

If the combined appliance

has to be pulled out of the

aperture again, take hold of

it in the lower third area and

pull it straight forwards.

NOTICE

Risk of damage when moving the combined SBS appliance!

The combined SBS appliance is heavy once assembled. The

appliance may be dented by improper movement.

Observe the information given on moving the appliance (see

above).

Remove all protective film from the outside of the housing.

Bottom front of the appliance:

Fig. 5

Tighten the outer adjustment feet. The appliances can be

moved easier

Push both appliances together up to approx. 10 mm apart so

that they stand flush at the front.

Line the appliances up with a spirit level on the top of the

appliance.

Top front of the appliance:

Fig. 6

Remove the existing covers.

Before fitting the top bracket remove both earthing screws

Fig. 6 (14)

Store the earthing screws safely. The screws are necessary

for fitting the bracket as shown below.

Fig. 7

Slide the bracket

Fig. 7 (3)

onto the pins with the spacer

between the appliances. Screw the brackets in loosely alter-

nately right and left with four screws

Fig. 7 (4)

and the previ-

ously removed earthing screws

Fig. 7 (14)

If necessary, line the appliances up with a spirit level on the

top of the appliance.

Bottom front of the appliance:

Side-by-side assembly

* Depending on model and options 3

Fig. 8

Remove the existing covers.

Slide the bracket

Fig. 8 (6)

on with the spacer between the

appliances and screw in loosely with the 4 screws

Fig. 8 (4)

If necessary line the appliances up again.

Now tighten the screws firmly at the top and bottom.

Top back of the appliance:

Fig. 9

Slide the bracket

Fig. 9 (7)

onto the top of the appliance with

the lugs and with the spacer between the appliances. Screw

in firmly with the 2 screws

Fig. 9 (5)

Bottom back of the appliance:

Fig. 10

NOTICE

Holes for the screws must be pre-drilled.

Slide the bracket

Fig. 10 (8)

on with the slots over the

retainer for the wall spacers.

Mark the position of the holes to be drilled with a pencil.

Remove the bracket again.

Fig. 11

NOTICE

Only drill through the metal plate. Drilling depth approx. 1mm.

Pre-drill the screw holes with a 3 mm drill and deburr.

Fig. 12

Slide the bracket

Fig. 12 (8)

on once more with the slots over

the retainer for the wall spacers.

Screw in tightly with the 2 screws

Fig. 12 (5)

Before fitting the top and front cover strips, push the two bars

together over the whole length. The strips can be inserted more

easily into the gap. Use a soft cloth to push the strips in to avoid

dents in the surface of the cover strips. Press the strips into the

gap carefully and evenly in order to achieve an optimum bond.

Side-by-side assembly

4 * Depending on model and options

Fig. 13

On the top press the short cover strip

Fig. 13 (9)

into the

horizontal gap.

Fig. 14

On the front, press the long trim

Fig. 14 (10)

into the vertical

gap. Ensure that the strip rests on the connecting plate.

Peel the protective film off the cover strip.*

Fig. 15

Snap the top cover

Fig. 15 (11)

onto the still open gap

between the two control panel trims. Make sure that the

outer sides of the cover form a flush finish with the control

panel trims

Fig. 16

Place the bottom cover

Fig. 16 (12)

onto the bracket from

the front (1), slide it down (2) and snap it in at the bottom (3).

To disassemble the cover, insert a screwdriver at the bottom

on the side below the cover and release both lower hooks.

The cover can swing out towards the top.

Connect the combination to the mains according to the

manual.

Appliances with IceMakers:

Connect the appliance to the fixed water connection

according to the manual.

NOTICE

Risk of damage when moving the combined SBS appliance!

The combined SBS appliance is heavy once assembled. The

appliance may be dented by improper movement.

Observe the information given on moving the appliance (see

above).

Carefully slide the combination into the intended position.

If necessary, align the height with the height-adjustable feet.

Then support the door: Lower the adjustment feet on the

mounting block until they rest on the floor then turn a further

90°.

The doors can be aligned in

height with the aid of the outer,

lower turn hinges:

Extend the threaded pin

Fig. 17 (17)

a little (by one

turn at most!).

Fig. 17

Fig. 18

In order to lift the door unscrew the mounting block

Fig. 18 (18)

clockwise with the supplied open-end wrench

Fig. 18 (2)

. When delivered the mounting block is completely

screwed in.

Tighten the threaded pin

Fig. 17 (17)

again to secure the

bearing pin.

Side-by-side assembly

* Depending on model and options 5

Liebherr-Hausgeräte Ochsenhausen GmbH

Memminger Straße 77-79

88416 Ochsenhausen

Deutschland

home.liebherr.com

Liebherr SBSbs 8673 Premium Owner's manual

Liebherr SBSbs 8673 Premium Owner's manual

Liebherr SBSbs 8673 Premium Owner's manual

Related papers