Traceable 4190 Owner's manual

Traceable
Brand
Traceable
Model
4190
Type
Owner's manual

Traceable 4190

Traceable 4190 is a humidity controller with a range of 30 to 90%RH and an accuracy of ±5%RH. It has a resolution of 1% and a load capacity of 15 Amps, 1800 Watts, 1/3 H.P. The device has an internal Ni-Cad rechargeable battery that powers the LCD display and maintains the program settings in the event of a power failure.

The Traceable 4190 is easy to use. The default display mode shows the current Relative Humidity and the status of the outlet (ON, OFF, or AUTO ON/OFF). You can press the MODE button once to display the current controller settings, or twice to enter the setting mode. In the setting mode, you can use the SET button to adjust the Humidity Set Point and the MANUAL button to select the desired switching function.

Traceable 4190

Traceable 4190 is a humidity controller with a range of 30 to 90%RH and an accuracy of ±5%RH. It has a resolution of 1% and a load capacity of 15 Amps, 1800 Watts, 1/3 H.P. The device has an internal Ni-Cad rechargeable battery that powers the LCD display and maintains the program settings in the event of a power failure.

The Traceable 4190 is easy to use. The default display mode shows the current Relative Humidity and the status of the outlet (ON, OFF, or AUTO ON/OFF). You can press the MODE button once to display the current controller settings, or twice to enter the setting mode. In the setting mode, you can use the SET button to adjust the Humidity Set Point and the MANUAL button to select the desired switching function.

SPECIFICATIONS
Range: 30 to 90%RH
Accuracy: ±5%RH
Update Rate: 10 seconds
Resolution: 1%
Load Capacity: 15 Amps, 1800 Watts, 1/3 H.P.
SET-UP
The unit is supplied with an internal Ni-Cad rechargeable battery that powers the LCD display and maintains the program settings in the event of a
power failure. Upon unpacking the Humidity Controller, the LCD display may be weak or blank. Prior to usage, plug the Humidity Controller
into a proper power source (120 Volts, 60Hz, 3-prong grounded) and charge the Ni-Cad battery overnight.
OPERATION
The default display mode shows the current Relative Humidity and the status of the outlet (ON, OFF, or AUTO ON/OFF).
Press the MODE button once to display the current controller settings, after 5 seconds, the unit will return to the default display mode.
SETTING THE CONTROLLER
From the default display mode, press the MODE button twice to enter the setting mode (the digits will flash).
Press the SET button to advance the Humidity Set Point on the display to the desired setting.
Press the MANUAL button to select the desired switching function:
▲= Higher On - Outlet will turn ON when the Relative Humidity rises above the Humidity Set point
X = Disable - Outlet will not perform any switching
▼= Lower On - Outlet will turn ON when the Relative Humidity falls below the Humidity Set Point
Once the desired Humidity Set Point and Switching Function has been set, press the MODE button to confirm your entry (unit will return to the
default display mode).
MANUAL OVERRIDE
To override the current outlet condition (on/off), press the MANUAL button. When the display reads ‘ON” or “OFF” without “AUTO” also appearing,
the outlet will stay in that condition until the unit is placed back into the “AUTO” mode by pressing the MANUAL button. “AUTO” must appear on the
display for the unit to turn on/off based on the controller settings.
Warranty, Service, or Recalibration
For warranty, service, or recalibration, contact:
CONTROL COMPANY
4455 Rex Road
Friendswood, Texas 77546 USA
Ph. 281-482-1714 Fax 281-482-9448
E-mail [email protected] www.control3.com
Control Company is ISO 9001 Quality-Certified by DNV and ISO 17025 accredited as a
Calibration Laboratory by A2LA.
Control Company Cat. No. 92-4190-00 Rev. 2 051608
Traceable
®
is a registered trademark of
Control Company
© 2008 Control Company
TRACEABLE®
HUMIDITY CONTROLLER
INSTRUCTIONS
  • Page 1 1

Traceable 4190 Owner's manual

Traceable
Brand
Traceable
Model
4190
Type
Owner's manual

Traceable 4190

Traceable 4190 is a humidity controller with a range of 30 to 90%RH and an accuracy of ±5%RH. It has a resolution of 1% and a load capacity of 15 Amps, 1800 Watts, 1/3 H.P. The device has an internal Ni-Cad rechargeable battery that powers the LCD display and maintains the program settings in the event of a power failure.

The Traceable 4190 is easy to use. The default display mode shows the current Relative Humidity and the status of the outlet (ON, OFF, or AUTO ON/OFF). You can press the MODE button once to display the current controller settings, or twice to enter the setting mode. In the setting mode, you can use the SET button to adjust the Humidity Set Point and the MANUAL button to select the desired switching function.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents