GE WSM2780HDWWW Installation guide

Brand: GE

Model: WSM2780HDWWW

Category: Washer dryers

Type: Installation guide

This manual is also suitable for

_AWARNING - POTE.TIALFI.EA.DSHOCKHAZA.D

• To reduce the risk of severe injury or death, follow all installation instructions.

• Clothes dryer installation must beperformed by a qualified installer.

• Install the clothes dryer according to these instructions and in accordance with local codes.

• This dryer must be exhausted to the outdoors.

• Use only 4" rigid metal ducting for exhausting the clothes dryer to the outdoors.

• DO NOTinstall a clothes dryer with flexible plastic ducting materials. If flexible metal (semi-rigid or foil-type} duct is installed,

it must be UL-listed and installed in accordance with the instructions found in "Connecting the Dryer to House Vent" on page

6 of this manual. Flexible ducting materials are known to collapse, be easily crushed, and trap lint. Theseconditions will

obstruct dryer airflow and increase the risk of fire.

• Do not install or store this appliance in any location where it could be exposed to water andlor weather.

• Savethese instructions. (Installers: Be sure to leave these instructions with the customer.}

• This appliance must be properly grounded and installed as described in these instructions.

CALIFORNIA SAFE DRINKING WATER AND TOXIC ENFORCEMENT ACT

Thisact requiresthegovernorof Californiato publisha list of substancesknownto the stateto causecancer,birth defectsorother

reproductiveharmand requiresbusinessesto warncustomersof potentialexposureto suchsubstances.Gasappliancescancauseminor

exposureto four of thesesubstances,namely benzene,carbonmonoxide,formaldehydeand soot, causedprimarily by the incomplete

combustionof natural gasor LPfuels.Properlyadjusted dryerswill minimizeincompletecombustion.Exposureto thesesubstancescanbe

minimizedfurther by properlyventingthe dryer to the outdoors.

IMPORTANT

• Exhaustingthe dryer to the outside

is required to prevent large

amounts of moisture, lint and other

products of combustion from being

blown into the room.

• Service information and awiring

diagram are located in the dryer

access panel.

TOOLS NEEDED

Slip-joint pliers

Phillips-head and flat-blade screwdrivers

Ratchet with 3/8" socket

Carpenter's level

Adjustable wrenches

Pipethread sealer

7] /2"

5P/S

® @

Vent _./_ i_,q

Water .............._"::_

inlets(rear)

Drainoutlet

(rear)

_27" _

PRODUCT DIMENSIONS

!6V4"

Gassupply

pipe (rear)

36V16"

5%/4"

/16"

05-09 JR

,/"

/'51 o

rl a

_ 3013/16"

21/2"

_1½"

!!VS

Installation Instructions

UNPACKING SPACEMAKER'"

rTj Remove tape two corner pads rear

and from

bottom corners of appliance.

j_] Using shipping corner posts, lag

the four the

appliance on its left side so the shipping base does

not rest on the floor.

Plastic spacer

block

Shipping Shipping Rear vent

blocks clips onlg

Mechanism Drain hose

shipping bolt

Foam

shippingpad

Shipping carton

corner posts

Remove the foam shipping pad.

Remove the washer shipping bolt using the ratchet

with 3/8" socket, and remove the plastic spacer

block using the slip-joint pliers.

Return the appliance to the upright position and

locate it in the general area to be installed. Provide

enough space at the rear for installing the water

inlet hose.

Untape and open the washer lid.

Remove:

a. foam tub blocking pad

b. foam shipping blocks from rear of unit

c. tape from drger door

d. foam drger support pads

e. inlet hoses

f. From the back of the washer, remove the wire

shipping clips securing the drain hose. Plastic

clamps secure the drain hose to the right side

of the washer backsheet. These clamps form a

standpipe to prevent water siphoning. DO NOT

REMOVETHESECLAMPS.

Drger

support pads

UNPACKING SPACEMAKER'" (CONT.)

NOTE:The tub blocking pad, shipping bolt and plastic

spacer should be retained for use if the appliance is

transported at a later date.

r_ Remove clips holding the following:

a. inlet hoses

b. drain hose

c. power cord

PREPARING DRAIN HOSE

[_ Form "U" the end of the drain hose with

shape

the hose pointed toward the drain.

TO]For an installation requiring a longer drain hose,

use the WH41X312 extra-long (108") drain hose.

Attach to the machine in the same manner as the

original hose.

Installation Instructions

MOVING SPACEMAKER T_TO OPERATING

LOCATION

_ emove the 2 screws securing the access panel

to the drger cabinet. Liftthe front access panel

until the tabs can be disengaged from the drger

cabinet, and remove the panel.

_ oute the inlet hoses, drain hose and power cord

through the rear access area for temporarg

holding when moving the appliance to the

operating location.

L -----;

panel

screws

To ensure the Laundrg Center is level and solid

on all four legs, tilt the Laundrg Center forward

so the rear legs are off the floor. Gentlg set the

Laundrg Center back down to allow the rear legs

to self-adjust. Place a level on top of the washer.

Check it side to side, then front to back. Screw

the front leveling legs up or down to ensure the

Laundrg Center is resting solidlg on all four legs

(no rocking of the Laundrg Center should occur).

NOTE: Keepthe leg extension at a minimum to prevent

excessive vibration.

CONNECTING TO PLUMBING FACILITIES

--ACAUTION: Besurewotersupplylineshove

been thoroughlg flushed to remove particles that

might clog the wesher filter screens.

Check inlet hoses to ensure the rubber washers

are installed in each end. (If gour laundrg center

has the hoses attached to the water valve,

proceed to Step !3A.) Carefullg connect the inlet

hoses to the water valve (on the left side of the

washer cabinet), tighten bg hand, and then

tighten another 2/3 turn with pliers.

_ACAUTION: DONOTCROSS-THREADOR

OVERTIGHTEN THESE CONNECTIONS.

_ etermine which water faucet isthe HOT water

faucet, carefullg connect the bottom inlet hose

to the HOTwater faucet, tighten bg hand,

and then tighten another 2/3 turn with pliers.

Carefullg connect the top inlet hose to the

COLDwater faucet, tighten bg hand, and then

tighten another 2/3 turn with pliers.

-_CAUTION: DoNOTCROSS-THREADOR

OVERTIGHTEN THESE CONNECTIONS.

Turn the water on and check for leaks at both

connections.

_ Place formed end of drain hose in drain facilitg

and secure with cable tie (provided in literature

package).

Cord length

4 ft.

"Cable tie abl;_ii_[.__

NOTE: Drain hose MUSTbe secured to drain facility in

all cases.

Installation Instructions

CONNECTING TO GAS SUPPLY

Connect the gas supply to the dryer. If codes

allow, use new flexible metal tubing (design

certified by the American Gas Association).

Be sure there are no kinks. For gas connections,

you MUSTuse pipe-joint compound resistant

to the action of LPgas.

-ACAUTION: Besure electricity is OFF at

power supply source (circuit breaker/fuse bo×l.

Plug power cord into electrical outlet.

IMPORTANT:120-volt, 60 hz, AC-only electrical supply

is required on a separate 15-ampere circuit fused by

a time-delay fuse or circuit breaker.

NOTE:Do not, under

any circumstances,

remove grounding

prong from plug.

Grounding

prong

FINAL APPLIANCE LEVELING

-ACAUTION: ALLWEIGHT MUSTBE

REMOVEDFROMAPPLIANCELEVELINGLEGWHILE

ADJUSTING.THREADS ON LEGWILL BEDAMAGED

OTHERWISE.

[T_ Again, make sure the appliance rests firmly on

all four legs. No rocking of the appliance should

occur.

CHECKING APPLIANCE OPERATION

[1"6] Make sure all packing and shipping materials

are removed, including the washer shipping bolt

and plastic spacer block.

Route drain hose properly-not coiled

or kinked.

Make sure water inlet hoses are connected

(HOTto HOT)and tightened securely without

kinks. Turn on water faucets and check for leaks.

Tape all joints to make sure exhaust ductwork

is secured without leaks.

Turn on electricity at the power source.

Turn on the washer and dryer and run through

one cycle. Check all hoses for leaks. Ensure

the burner has lit.

NOTE:Before the burner will light, it is necessary for

the gas line to be bled of air. If the burner does not light

within 45 seconds the first time the dryer isturned on,

the safety switch will shut off the burner. If this happens,

turn the timer to "OFF"and wait 5 minutes before

making another attempt to light.

REPLACING FRONT ACCESS PANEL

[_l Reinstall the safety cover and front access panel.

_ lace the Owner's Manual and Installation

Instructions in a location where they can be

found by the customer.

Installation Instructions

PLUMBING INFORMATION

WATER SUPPLY REQUIREMENTS

• HOTANDCOLDWATERFAUCETS- Must be within 42"

of the appliance water inlet hose connections. The

faucets must be 3/4" garden hose-type so inlet

hoses can be connected.

WATERPRESSURE- Must be between 10 and 120

pounds per square inch with a maximum unbalance

pressure, hot vs. cold flowing, of 10 pounds per

square inch.

• SHUT-OFFVALVES- Both hot and cold water shut-off

valves (faucets) should be supplied.

• LOCATION- Do not install appliance in an area where

the temperature will fall below freezing. If appliance is

stored or transported in freezing temperatures, be sure

all water from the fill and drain systems has been

removed.

DRAIN REQUIREMENTS

• DRAINRATE- The drain or standpipe must be capable

of accepting a discharge at the rate of 16 gallons per

minute.

• DRAINHEIGHT- The drain height must be 33"

minimum and 96" maximum.

STANDPIPEDIAMETER- The standpipe diameter must

be 1" minimum. There MUSTbe an air gap around the

drain hose in the standpipe. A snug fit can cause a

siphoning action.

• SIPHONBREAKKIT- Fora drain facility less than 33"

high, the hose, coupling and clamps provided in the

machine must be used and, in addition, a siphon break

MUSTbe installed on the back of the machine. Use

Siphon Break Kit WHagX228 and FOLLOW

INSTRUCTIONSINTHE KIT.

ELECTRICAL CON NECTION

INFORMATION

-&CAUTION: For personal safety:

TURN OFF ELECTRICITYAT POWERSOURCE(CIRCUIT

BREAKER/FUSEBOX)BEFOREINSTALLINGOR

SERVICINGTHISAPPLIANCE.

DO NOT USE AN EXTENSION CORD WITH THIS

APPLIANCE.

THIS APPLIANCE MUST BE PROPERLY GROUNDED.

This appliance must be electrically grounded in

accordance with local codes and ordinances or,

in the absence of local codes, in accordance with the

NATIONALELECTRICALCODE,ANSI/NFPANO.70-1987.

ELECTRICAL REQUIREMENTS

• This appliance should be connected to an individual

branch circuit with 120-volt, single-phase, 60 Hz

electrical service and should be protected by 15-amp

time-delay fuses or circuit breakers.

GAS CONNECTION INFORMATION

- CAUTION:

Do not attempt to alter gas orifice or adjust burner air

shutter. Natural gas input may vary in some areas from

700 to 1200 B.T.U.per cubic foot. If the gas orifice or

burner air shutter is incorrectly adjusted, serious

personal injury and/or fire hazard can occur. Your local

gas company will know the qualities of the gas in your

area. Contact your local servicing dealer if burner

adjustment or orifice changes are necessary.

Do not use an open flame for leak testing. Serious

personal injury and/or a fire hazard can result if an open

flame is used to test for gas leaks. Use a soap and water

solution to test all gas line fittings.

Do not install the Laundry Center to an L.R gas supply

without installing conversion kit. All Laundry Centers

are shipped with a pressure regulator and natural gas

orifice. Using a natural gas orifice with an L.R gas supply

can result in personal injury, clothes damage and/or a

fire hazard Have a qualified gas technician install a

conversion kit in the Laundry Center before use.

• Installation must meet American National Standard,

National Fuel Gas Code ANSIZ223.1-1988 and local

codes and ordinances.

• The gas supply line should be a 1/2" pipe. A 1/2" to

3/8" reducer must be used to connect the dryer to

the supply line.

• The gas supply line must have a shut-off valve

preferably within 6 feet (1.8m) of the dryer.

,,A 1/8" NPTplugged tapping, accessible for test gauge

connection, must be installed immediately upstream

of the gas supply connection.

Installation Instructions

ADJUSTING FOR ELEVATION

• Gasclothes dryers input ratings are based on sea level

operation and need not be adjusted for operation at

or below 2000 ft. elevation. Foroperation at elevations

above 2000 ft., input ratings should be reduced at a

rate of 4 percent for each 1000 ft. above sea level.

• Installation must conform to local codes and ordinances

or,in their absence, the NATIONALFUELGASCODE,

ANSIZ225.

EXHAUST

WARNING - Toreducetheriskoffire

or personal injury:

• This clothes dryer must be exhausted to the outdoors.

• Useonly 4" rigid metal ducting for the home exhaust

duct.

• Useonly 4" rigid metal or UL-listed flexible metal

(semi-rigid or foil-type) duct to connect the dryer to

the home exhaust duct. It must be installed in

accordance with the instructions found in "Connecting

the Dryer to House Vent" on page 7 of this manual.

• Do not terminate exhaust in a chimney, a wall,

a ceiling, gas vent, crawl space, attic, under an

enclosed floor, or in any other concealed space

of a building.

• Never terminate the exhaust into a common duct

with a kitchen exhaust system. A combination

of grease and lint creates a 3otential fire hazard.

• Do not use duct longer than specified in the exhaust

length table. Longer ducts can accumulate lint,

creating a potential fire hazard.

• Never install a screen in or over the exhaust duct.

This will cause lint to accumulate, creating a potential

fire hazard.

• Do not assemble ductwork with any fasteners that

extend into the duct. These fasteners can accumulate

lint, creating a potential fire hazard.

• Do not obstruct incoming or exhausted air.

• Provide an access for inspection and cleaning of the

exhaust system, especially at turns and joints. Exhaust

system shall be inspected and cleaned at least once

a year.

• Remove and discard existing plastic or metal foil duct

and replace with UL-listed duct.

Remove any lint from the wall exhaust opening.

Internal _j Wall

duct

opening.............._.__ .........._ Checkthatexhaust

f_'_X .,J_..........._j" hooddamperopens

andclosesfreely.

EXHAUST (CONT.)

EXHAUST DUCT LENGTH iNFORMATiON

• The MAXIMUMALLOWABLElength of the exhaust system

depends upon the type of duct, number of turns, the

type of exhaust hood (wall cap) and all conditions noted

below. Morethan three 90° turns are not recommended.

NUMBER

OF 90 °

TURNS

EXHAUST

HOOD TYPE

A B

46 ft. 37ft.

38 ft. 30ft.

31 ft. 22 ft.

24 ft. 15 ft.

Rearvent only

Maximum length of 4"

diameter rigid metal duct

HOOD OR WALL CAP

• Terminate in a manner to prevent back drafts or entry

of birds or other wildlife.

• Termination should present minimal resistance to

the exhaust airflow and should require little or no

maintenance to prevent clogging.

Never install a screen over the exhaust duct.

• Wall caps must be installed at least 12" above ground

level or any other obstruction with the opening pointed

down.

TURNS OTHER THAN 90 °

• Oneturn of 45° or less may be ignored.

Two/45° turns should be treated as one 90°.

CONNECTING THE DRYER TO HOUSE VENT

Rigid Metal Transition Duct

For best drying performance, a rigid metal transition

duct is recommended.

Rigid metal transition ducts reduce the risk of crushing

and kinking.

UL-Listed Flexible Metal (Semi-Rigid)Transition Duct

If rigid metal duct cannot be used, then UL-listed

flexible metal (semi-rigid) ducting can be used (Kit

WX08X!0077).

• Never install flexible metal duct in walls, ceilings, floors

or other enclosed spaces.

Total length of flexible metal duct should not exceed

8 feet (2./4m).

• For many applications, installing elbows at both the

dryer and the wall is highly recommended (see

illustration at left). Elbows allow the dryer to sit close

to the wall without kinking and or crushing the

transition duct, maximizing drying performance.

Avoid resting the duct on sharp objects.

Installation Instructions

CONNECTING THE DRYER TO HOUSE VENT

{CONT.)

UL-Listed Flexible Metal (Foil-Type)Transition Duct

• In special installations, it meg be necessary to connect

the dryer to the house vent using e flexible metal

(foil-type) duct. A UL-listed flexible metal (foil-type) duct

meg be used ONLYin installations where rigid metal

or flexible metal (semi-rigid) ducting cannot be used

AND where a 4" diameter can be maintained

throughout the entire length of the transition duct.

In Canada end the United States, only the flexible

metal (foil-type) ducts that comply with the "Outline for

Clothes Dryer Transition Duct, Subject 2158A" shell be

used.

• Never install flexible metal duct in wells, ceilings, floors

or other enclosed spaces.

Total length of flexible metal duct should not exceed

8 feet (2.4 m).

• Avoid resting the duct on sharp objects.

For best drying performance:

1. Slide one end of the duct over the clothes dryer outlet

pipe.

2. Secure the duct with e clamp.

5. With the dryer in its permanent position, extend the

duct to its full length. Allow 2" of duct to overlap the

exhaust pipe. Cut off end remove excess duct. Keep

the duct us straight us possible for maximum airflow.

4. Secure the duct to the exhaust pipe with the other

clamp.

SEALING OF JOINTS

• All joints should be tight to ovoid leeks.

NOTE:The mule end of each section of duct must point

away from the dryer.

Do not assemble ductwork with fasteners that

extend into the duct. They will serve as e collection

point for lint.

Duct joints can be made air- end moisture-tight by

wrapping the overlapped joints with duct tape.

INSULATION

• Ductwork that runs through an unheated area or

is near an air conditioning duct should be insulated

to reduce condensation end lint buildup.

PARTS AVAILABLE FROM LOCAL SERVICE

ORGANIZATIONS

• Rigid Metal Duct Components

WX8X65 a" x 1' Duct

WX8X64 4" x 2' Duct

WX8X51 4" Elbow

WX8X59 4" Aluminum Hood

• Flexible Metal Duct Components

WX8X58 4" Clamps (2)

WX8X59 4" Aluminum Hood

WX08X10077 6' UL-Listed, Flexible Metal (Semi-Rigid)

Duct, 2 Clamps, 2 Close Elbows

MOBILE HOME INSTALLATION

• Installation must conform to Manufactured Home

Construction and Safety Standard, Title 24 CFR,

Part 32-80.

The dryer must be exhausted to the outside with

the termination securely fastened to the mobile

home structure.

The exhaust MUSTNOTbe terminated beneath the

mobile home.

The exhaust duct material MUSTNOTsupport

combustion.

CONSIDERATIONMUSTBEGIVENTOPROVIDEADEQUATE

CLEARANCESFORINSTALLATIONAND SERVICE.

ALCOVE OR CLOSET INSTALLATION

i Ir

60 Sq.In.

60 Sq. In.

"-- _ 0...... O"

• If your dryer is approved for installation in on alcove

or closet, it will be stoted on o Iobel on the bock of

the dryer.

TO PREVENT LARGE AMOUNTS OF LINT AND MOISTURE

FROM ACCUMULATING AND TO MAINTAIN DRYING

EFFICIENCY,THIS MACHINE MUST BE EXHAUSTED

OUTDOORS.

• DO NOTinstoll this opplionce with less thon

the minimum cleoronces shown obove.

CONSIDERATION MUST BEGIVEN TO PROVIDE ADEQUATE

CLEARANCES FOR INSTALLATION AND SERVICE.

CAUTION: DO NOT INSTALL THIS APPLIANCE

IN A CLOSET WITH A SOLID DOOR.

Installation Instructions

WARNING -

For your safety, the information in this manual must

be followed to minimize the risk of fire or explosion or to

prevent property damage, personal injury or loss of life.

• Do not store or use gasoline or other flammable vapors

and liquids in the vicinity of this or any other appliance.

• WHAT TO DO IF YOUSMELLGAS

• Do not trg to light ang appliance.

• Do not touch ang electrical switch; do not use ang

phone in gour building.

• Clear the room, building or area of all occupants.

• Immediatelg call gour gas supplier from a neighbor's

phone. Follow the gas supplier's instructions.

• If gou cannot reach gour gas supplier, call the fire

department.

Installation and service must be performed bg a qualified

installer, a service agencg or the gas supplier.

MISCELLANEOUS REQUIREMENTS

LOCATION

• The appliance must be installed on firm flooring to

minimize vibration during spin cgcles. Concrete flooring

is best, but wood base issufficient, provided the floor

support meets FHAstandards.

• The appliance should not be installed on rugs or

exposed to the weather.

DOOR VENTILATION OPENING

A minimum of 120 square inches of opening, equallg

divided at top and bottom, is required. Air openings are

required to be unobstructed when a door is installed.

A Iouvered door with equivalent air openings for the

full length of the door is acceptable.

/° /

I 60

Sq.In.

Sq. In.

When louvers or registers are placed in door openings,

the free air openings of the louvers or registers must

equal 120 square inches.

GE WSM2780HDWWW Installation guide

Brand: GE

Model: WSM2780HDWWW

Category: Washer dryers

Type: Installation guide

This manual is also suitable for

Download PDF

report

GE WSM2780HDWWW Installation guide

This manual is also suitable for

GE WSM2780HDWWW Installation guide

Related papers

Other documents