D-Link DMP-CD100 User manual

Brand: D-Link

Model: DMP-CD100

Category: CD players

Type: User manual

D-Link DMP-CD100 is a compact disc player that supports playing MP3 encoded audio CDs. It is equipped with a laser beam to read the data from the disc and a built-in speaker to project the sound. It can be connected to a power supply and comes with a safety device to turn off the laser beam when the disc compartment is opened. The device is FCC compliant and meets the safety standards of the U.S. Department of Health and Human Services.

DMP-CD100

MP3 CD Player

User’s Manual

CE Mark Warning

This is a Class B product. In a domestic environment, this product may cause radio

interference, in which case the user may be required to take adequate measures

Warnung!

Dies ist in Produkt der Klasse B. Im Wohnbereich kann dieses Produkt

Funkstoerungen verursachen. In diesem Fall kann vom Benutzer verlangt werden,

angemessene Massnahmen zu ergreifen.

Advertencia de Marca de la CE

Este es un producto de Clase B. En un entorno doméstico, puede causar interferencias

de radio, en cuyo case, puede requerirse al usuario para que adopte las medidas

adecuadas.

Attention!

Ceci est un produit de classe B. Dans un environnement domestique, ce produit

pourrait causer des interférences radio, auquel cas l`utilisateur devrait prendre les

mesures adéquates.

Attenzione!

Il presente prodotto appartiene alla classe B. Se utilizzato in ambiente domestico il

prodotto può causare interferenze radio, nel cui caso è possibile che l`utente debba

assumere provvedimenti adeguati.

FCC INFORMATION

This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions: (1) This device may not cause harmful interference, and (2)

this device must accept any interference received, including interference that may

cause undesirable operation.

NOTE: This equipment has been tested and found to comply with the limits for a

Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses and can radiate radio frequency energy

and, if not installed and used in accordance with the instructions, may cause harmful

interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

• Consult the dealer or an experienced radio TV technician for help.

SAFETY CERTIFICATION

This compact disc player is made and tested to meet safety standards of the FCC,

requirements and compliance with safety performance of the U.S. Department of

Health and Human Services, and also with FDA Radiation Performance Standards 21

CFR Subchapter J.

SAFETY PRECAUTIONS

• Do not take the DMP-CD100 apart. The laser beam used in the DMP-CD100

could harm your eyes.

• Do not insert pins, etc., inside the DMP-CD100. This unit is equipped with a

safety device which automatically turns the laser beam off when the disc

compartment is opened. If a pin or other metal object should get inside the

DMP-CD100, however, this safety device may be deactivated.

• The DMP-CD100 should be connected to a power supply only of the type

described in the operating instructions or as marked on the appliance.

• Power supply cords should be routed so that they are not likely to be walked on

or pinched by items placed upon or against them, pay particular attention to cords

at plugs, convenience receptacles, and the point where they exit from the

DMP-CD100.

• Never remove the enclosure. If the internal parts are touched accidentally, a

serious electric shock might occur.

• If an abnormal smell or smoke is detected, immediately turn the power OFF and

pull out the power cord. Contact your dealer or nearest service center.

• Avoid placing the DMP-CD100 under direct sunlight or near a source of heat

such as heating equipment. Particularly, never leave it in an automobile or on the

dashboard.

• The DMP-CD100 may not function properly if used at extremely low, or

freezing temperatures. The ideal ambient temperature is above +5°C (41°F).

• Avoid places where it is dusty or where the humidity is high.

• Avoid placing the DMP-CD100 on an unstable surface such as a shelf or in a

place subject to vibrations.

• Keep the DMP-CD100 away from sources of magnetic fields such as TV sets,

speaker systems, radios, motorized toys or magnetized object.

• Do not use volatile solvents such as alcohol, paint thinner, gasoline, or benzene,

etc. To clean the cabinet, use a clean dry cloth.

• The user should not attempt to service the DMP-CD100 beyond that described in

the operating instructions. All other servicing should be referred to qualified

service personnel.

WARNING:

TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS

APPLIANCE TO RAIN OR MOISTURE.

LIMITED WARRANTY

D-Link Systems, Inc. (“D-Link”) provides this limited warranty for its product only to the person

or entity who originally purchased the product from D-Link or its authorized reseller or

distributor.

Limited Hardware Warranty: D-Link warrants that the hardware portion of the

D-Link products described below (“Hardware”) will be free from material defects in

workmanship and materials from the date of original retail purchase of the Hardware, for the

period set forth below applicable to the product type (“Warranty Period”) if the Hardware is used

and serviced in accordance with applicable documentation; provided that a completed

Registration Card is returned to an Authorized D-Link Service Office within ninety (90) days

after the date of original retail purchase of the Hardware. If a completed Registration Card is

not received by an authorized D-Link Service Office within such ninety (90) period, then the

Warranty Period shall be ninety (90) days from the date of purchase.

Product Type Warranty Period

Product (excluding power supplies and fans), if

purchased and delivered in the fifty (50) United States,

or the District of Columbia (“USA”)

As long as the original

purchaser still owns the

product

Product purchased or delivered outside the USA One (1) Year

Power Supplies and Fans One (1) Year

Spare parts and spare kits Ninety (90) days

D-Link’s sole obligation shall be to repair or replace the defective Hardware at no charge to the

original owner. Such repair or replacement will be rendered by D-Link at an Authorized

D-Link Service Office. The replacement Hardware need not be new or of an identical make,

model or part; D-Link may in its discretion may replace the defective Hardware (or any part

thereof) with any reconditioned product that D-Link reasonably determines is substantially

equivalent (or superior) in all material respects to the defective Hardware. The Warranty

Period shall extend for an additional ninety (90) days after any repaired or replaced Hardware is

delivered. If a material defect is incapable of correction, or if D-Link determines in its sole

discretion that it is not practical to repair or replace the defective Hardware, the price paid by the

original purchaser for the defective Hardware will be refunded by D-Link upon return to D-Link

of the defective Hardware. All Hardware (or part thereof) that is replaced by D-Link, or for

which the purchase price is refunded, shall become the property of D-Link upon replacement or

refund.

Limited Software Warranty: D-Link warrants that the software portion of the product

(“Software”) will substantially conform to D-Link’s then current functional specifications for the

Software, as set forth in the applicable documentation, from the date of original delivery of the

Software for a period of ninety (90) days (“Warranty Period”), if the Software is properly

installed on approved hardware and operated as contemplated in its documentation. D-Link

further warrants that, during the Warranty Period, the magnetic media on which D-Link delivers

the Software will be free of physical defects. D-Link’s sole obligation shall be to replace the

non-conforming Software (or defective media) with software that substantially conforms to

D-Link’s functional specifications for the Software. Except as otherwise agreed by D-Link in

writing, the replacement Software is provided only to the original licensee, and is subject to the

terms and conditions of the license granted by D-Link for the Software. The Warranty Period

shall extend for an additional ninety (90) days after any replacement Software is delivered. If a

material non-conformance is incapable of correction, or if D-Link determines in its sole

discretion that it is not practical to replace the non-conforming Software, the price paid by the

original licensee for the non-conforming Software will be refunded by D-Link; provided that the

non-conforming Software (and all copies thereof) is first returned to D-Link. The license

granted respecting any Software for which a refund is given automatically terminates.

What You Must Do For Warranty Service:

Registration Card. The Registration Card provided at the back of this manual must be

completed and returned to an Authorized D-Link Service Office for each D-Link product within

ninety (90) days after the product is purchased and/or licensed. The addresses/telephone/fax

list of the nearest Authorized D-Link Service Office is provided in the back of this manual.

FAILURE TO PROPERLY COMPLETE AND TIMELY RETURN THE REGISTRATION

CARD MAY AFFECT THE WARRANTY FOR THIS PRODUCT.

Submitting A Claim. Any claim under this limited warranty must be submitted in writing

before the end of the Warranty Period to an Authorized D-Link Service Office. The claim must

include a written description of the Hardware defect or Software nonconformance in sufficient

detail to allow D-Link to confirm the same. The original product owner must obtain a Return

Material Authorization (RMA) number from the Authorized D-Link Service Office and, if

requested, provide written proof of purchase of the product (such as a copy of the dated purchase

invoice for the product) before the warranty service is provided. After an RMA number is

issued, the defective product must be packaged securely in the original or other suitable shipping

package to ensure that it will not be damaged in transit, and the RMA number must be

prominently marked on the outside of the package. The packaged product shall be insured and

shipped to D-Link, 53 Discovery Drive, Irvine CA 92618, with all shipping costs prepaid.

D-Link may reject or return any product that is not packaged and shipped in strict compliance

with the foregoing requirements, or for which an RMA number is not visible from the outside of

the package. The product owner agrees to pay D-Link’s reasonable handling and return

shipping charges for any product that is not packaged and shipped in accordance with the

foregoing requirements, or that is determined by D-Link not to be defective or non-conforming.

What Is Not Covered:

This limited warranty provided by D-Link does not cover:

Products that have been subjected to abuse, accident, alteration, modification, tampering,

negligence, misuse, faulty installation, lack of reasonable care, repair or service in any way that

is not contemplated in the documentation for the product, or if the model or serial number has

been altered, tampered with, defaced or removed;

Initial installation, installation and removal of the product for repair, and shipping costs;

Operational adjustments covered in the operating manual for the product, and normal

maintenance;

Damage that occurs in shipment, due to act of God, failures due to power surge, and cosmetic

damage; and

Any hardware, software, firmware or other products or services provided by anyone other than

D-Link.

Disclaimer of Other Warranties: EXCEPT FOR THE LIMITED WARRANTY SPECIFIED

HEREIN, THE PRODUCT IS PROVIDED “AS-IS” WITHOUT ANY WARRANTY OF ANY

KIND INCLUDING, WITHOUT LIMITATION, ANY WARRANTY OF

MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND

NON-INFRINGEMENT. IF ANY IMPLIED WARRANTY CANNOT BE DISCLAIMED IN

ANY TERRITORY WHERE A PRODUCT IS SOLD, THE DURATION OF SUCH IMPLIED

WARRANTY SHALL BE LIMITED TO NINETY (90) DAYS. EXCEPT AS EXPRESSLY

COVERED UNDER THE LIMITED WARRANTY PROVIDED HEREIN, THE ENTIRE

RISK AS TO THE QUALITY, SELECTION AND PERFORMANCE OF THE PRODUCT IS

WITH THE PURCHASER OF THE PRODUCT.

Limitation of Liability: TO THE MAXIMUM EXTENT PERMITTED BY LAW, D-LINK IS

NOT LIABLE UNDER ANY CONTRACT, NEGLIGENCE, STRICT LIABILITY OR OTHER

LEGAL OR EQUITABLE THEORY FOR ANY LOSS OF USE OF THE PRODUCT,

INCONVENIENCE OR DAMAGES OF ANY CHARACTER, WHETHER DIRECT, SPECIAL,

INCIDENTAL OR CONSEQUENTIAL (INCLUDING, BUT NOT LIMITED TO, DAMAGES

FOR LOSS OF GOODWILL, WORK STOPPAGE, COMPUTER FAILURE OR

MALFUNCTION, LOSS OF INFORMATION OR DATA CONTAINED IN, STORED ON,

OR INTEGRATED WITH ANY PRODUCT RETURNED TO D-LINK FOR WARRANTY

SERVICE) RESULTING FROM THE USE OF THE PRODUCT, RELATING TO

WARRANTY SERVICE, OR ARISING OUT OF ANY BREACH OF THIS LIMITED

WARRANTY, EVEN IF D-LINK HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH

DAMAGES. THE SOLE REMEDY FOR A BREACH OF THE FOREGOING LIMITED

WARRANTY IS REPAIR, REPLACEMENT OR REFUND OF THE DEFECTIVE OR

NON-CONFORMING PRODUCT.

GOVERNING LAW: This Limited Warranty shall be governed by the laws of the state of

California.

Some states do not allow exclusion or limitation of incidental or consequential damages, or

limitations on how long an implied warranty lasts, so the foregoing limitations and exclusions may

not apply. This limited warranty provides specific legal rights and the product owner may also have

other rights which vary from state to state.

Trademarks

D-Link is a registered trademark of D-Link Corporation/D-Link Systems, Inc. All other

trademarks belong to their respective proprietors.

No part of this publication may be reproduced in any form or by any means or used to

make any derivative such as translation, transformation, or adaptation without

permission from D-Link Corporation/D-Link Systems Inc., as stipulated by the United

States Copyright Act of 1976.

Page is loading ...

MP3 FILE INFORMATION

WHAT IS MP3?

MP3 is the abbreviation of “MPEG 1 Audio Layer 3”. MPEG Audio is a

compression specification that compresses the audio portion only. This audio

compression method is used in DVD and Video CD, etc. The audio data has

been compressed into about 1/10 the size of a normal audio file.

SEQUENCE OF PLAYING MP3 FILES

MP3 files will be played in the sequence that the writing software had

recorded. Therefore, it may be different between the sequence that you want

to record and the sequence of playing. To ensure that the songs play in the

order that you want, input “01” ~ “99” before the file names in the desired

sequence and then record onto a CD-R. Refer to your CD recording software

for options on organizing MP3 files.

IMPORTANT NOTES

D-Link is not responsible for playability of MP3 in any case due to recording

condition such as PC performance, writing software, media ability or etc.

ACCEPTABLE MEDIUM

• CD-DA Audio CD

• CD-R : ISO-9660 or Joliet file structure.

• Maximum number of recognizable directories : 255

SETTINGS FOR YOUR MP3 ENCODER AND CD WRITER

• When you use your MP3 encoder to compress audio data to an MP3 file,

set the transfer bit rate of the encoder to fixed 128 kbps (Constant Bit

Rate).

• Sampling frequency is 44.1 kHz.

• When burning your MP3 CD’s, check “Disc at Once”.

WRITING FILES ONTO A CD

When a CD containing MP3 data is loaded, the DMP-CD100 checks all the

files on the CD. If the CD contains a lot of folders or non-MP3 files, it will

take time for the DMP-CD100 to start playing MP3 files. In addition, it may

also take time for the DMP-CD100 to move to the next MP3 file. A file

search or folder search may not be performed smoothly. You should not write

non-MP3 files or unneeded folders along with MP3 files on the CD.

POWER SUPPLY

RECHARGEABLE NICKEL -

CADMIUM BATTERY

INSTALLATION

1. Remove the battery compartment

cover by sliding the cover away from

the DMP-CD100.

2. Insert the rechargeable

nickel-cadmium battery into the

battery compartment. Be sure to

observe the proper polarity (The +

and - signs, as indicated inside the

battery compartment).

NOTE: Fully charge the

rechargeable nickel - cadmium

battery before using it for the first

time.

3. Close the battery compartment.

4. Plug one end of the supplied AC adaptor into the DC jack.

Then plug the other end into an AC wall outlet.

5. When charging is completed, disconnect the AC adaptor plugs from both

the DMP-CD100 and the AC outlet.

NOTE:

• The battery takes approximately 10-15 hours after the AC adaptor is

connected to be fully charged.

• The indicator on the right side of the DMP-CD100 will light on during

charging.

• Use the DMP-CD100 with the supplied AC adaptor. Using with other

AC adaptors could damage the DMP-CD100.

• The DMP-CD100 can be powered up by using the AC adaptor alone

without batteries.

NICKEL-CADMIUM (NICAD) BATTERIES

The DMP-CD100 is equipped with battery recharging circuitry. For safety

measures, it requires specifically made NICAD (Nickel-Cadmium) batteries.

Use ONLY the following rechargeable battery types: KENWOOD NB-77 /

NB-88, PANASONIC RP-BP60D, SONY NH-DM2AA or equivalent.

NOTE: It is always a good idea to let Nickel-Cadmium batteries run all the

way down before charging them. When you do charge them, do so to their

full potential and they will last longer and provide more power.

ALKALINE BATTERY INSTALLATION

Insert two AA batteries into the battery compartment on the bottom of the

DMP-CD100. Be sure to observe the proper polarity (The “+” and “-“ signs,

as indicated inside the battery compartment).

NOTE:

• When replacing the alkaline batteries, use two new batteries of the same

type.

• When inserting the batteries, mistakenly inserting even one with

improper polarity will cause leakage.

BATTERY REPLACEMENT

If the rechargeable nickel-cadmium battery or the alkaline batteries are below

2.1v, the battery- low indicator will be shown on the display.

Recharge the rechargeable nickel-cadmium battery or replace the alkaline

batteries before using the DMP-CD100.

FEATURE LAYOUT

1. Disc Compartment Door

2. Electronic Shock Protection

Button (ESP)

3. Stop Button

4. Program Button

5. Reverse skip/Search Button

6. Display Window

7. Play/Pause Button

8. Mode/ Repeat Button

9. Forward skip/Search Button

10. Track Digit Button (T.Digit)

11. DBBS switch

12. Door Open Switch

13. Hold switch

14. Volume knob

15. Line Out Jack

16. Headphone Jack

17. Power Indicator

(Charging Indicator)

18. Batteries Compartment

19. AC-DC adaptor Input Jack

LCD DISPLAY INDICATORS

PLAYING A CD

1. Connect the headphones to the headphone

jack.

2. Set the volume knob to minimum.

3. Slide the door open switch to open the Disc

compartment door.

4. Insert a disc (CD or CD-R) with the label

side facing up.

5. Push down on the center of the front edge of

the door to close securely.

6. Slide the hold switch to the “OFF”

position.

7. Press the Play/Pause button. The

total number of tracks and total playing

time will be shown on the LCD display.

The DMP-CD100 will then start

playing track 1 of the disc

automatically.

8. Adjust the volume knob to a

comfortable level.

9. During playback mode, the track

number and elapsed playing time are displayed.

SKIP DURING PLAY MODE

1. Press the forward skip/search button once to skip to the beginning of the

next track.

2. Press the forward skip/search button repeatedly to skip ahead to the

beginning of other tracks.

3. Press the reverse skip/search button once to skip to the beginning of the

current track.

4. Press the reverse skip/search button twice or more quickly to go back to

previous tracks.

SEARCH DURING PLAY MODE

1. Press and hold the skip/search button to quickly advance or reverse

through the music at high speed.

2. Release the skip/search buttons to return to normal play.

BASIC FEATURES

PAUSE BUTTON

1. Press the play/pause button to pause playback temporarily.

2. The elapsed time will flash when paused.

3. Press it again to resume play.

STOP BUTTON

1. Press the stop button to stop playing the disc. The total number of tracks

will be shown on the display.

2. Press the Stop button to turn off the DMP-CD100.

HOLD SWITCH

1. Once all adjustments/selections

are completed, the hold switch may

be set to the (ON) position, and the

(HOLD) indicator appear on display, thereby deactivating all button

functions and eliminating the possibility of accidental unwanted selection.

2. Set to (OFF) position to resume normal operation.

DBBS SWITCH

1. This switch enhances the low frequency (BASS)

response.

2. Set the volume knob to a low listening level before activating the DBBS

switch, then adjust to your preference.

Note: The DBBS uses more battery power, thus drawing battery life more

quickly. Switch the DBBS to the Off position to conserve battery power.

REPEAT FEATURES

REPEAT ONE PLAY

1. Press the REPEAT/MODE Button until the

(REPEAT 1) Indicator appear on the display.

2. Select the desired track by pressing the

FORWARD OR REVERSE SKIP / SEARCH

Button.

3. The selected track will then begin playing

through to its end at which point it will

automatically return to the beginning of that track.

REPEAT ALL PLAY

1. Press the REPEAT/MODE Button until the

(REPEAT ALL) Indicator appear on the display.

2. The disc will then begin playing through to the

end of the last track, at which point it will

automatically return to the beginning of the first

track.

ELECTRONIC-SHOCK PROTECTION (ESP)

1. Press the ELECTRONIC SHOCK

PROTECTION button (ESP) to activate

the shock protection control function

during “Audio CD” play only.

2. The DMP-CD100 will store the CD’s

digital data in memory and then play back

from the memory.

3. If vibration occurs on the disc, the

DMP-CD100 will continue the playback

for 10 seconds until the display has shown

running out of lines in the tank.

4. In case of excessive vibration, the memory data may be exhausted and the

Electronic Shock Protection (ESP) may become temporarily ineffective.

NOTE: The battery power consumes more quickly when the Electronic Shock

Protection control is used. It is therefore recommended to set the ESP control

off when the DMP-CD100 is used in a place free of vibration.

ADVANCED PLAYING MODES

INTRO PLAY (INTRO)

1. Press the STOP button until the total track

number and total plays time appears on the

display.

2. Press the REPEAT/MODE button until the

Intro Indicator (INTRO) flash on the display.

3. Press the PLAY / PAUSE button to start

playing the Intro mode.

4. The disc will then begin playing the first ten

seconds of all tracks once and then stops

automatically.

PROGRAM PLAY (PGM)

1. Press the PROGRAM button until you see the

Program Indicator (PGM) flashing on the display.

2. Press the FORWARD OR REVERSE SKIP /

SEARCH button to select the desired track

number.

3. Press the PROGRAM button to store the track

number into that memory location. The next

memory location will flash on the display.

4. Repeat Steps 2 and 3 to store up to 22 tracks.

5. Press the PLAY / PAUSE button to start the

program play.

6. When the last programmed track has finished

playing, the DMP-CD100 will stop

automatically.

TO VIEW THE PROGRAMMED CONTENTS

1. Press the STOP Button once to stop the program play.

2. Press the PROGRAM Button repeatedly to display programmed tracks one

by one in the programmed order.

TO CLEAR THE PROGRAMMED CONTENTS

1. Press the STOP button twice or open the compartment door to clear the

program.

RANDOM PLAY (RDM)

1. Press the STOP button until the total track

number and total playtime appear on the display.

2. Press the REPEAT/MODE button until you see

the Random Indicator (RDM) flash on the

display.

3. Press the PLAY / PAUSE button to start the

Random play.

4. The DMP-CD100 will play tracks in a random

sequence selected from all tracks on the disc.

5. When all disc tracks have been played, the

DMP-CD100 will stop automatically.

MP3 DISC - TRACK DIGIT SELECTION PLAY (T.DIGIT)

1. By pressing the T. DIGIT Button (Track Digit), you can select high

numbered tracks quickly. Press the T-DIGIT once, twice, and thirdly, and

the digit representing hundredth, tenth and first number position will flash

respectively.

2. Press the FORWARD OR REVERSE SKIP/SEARCH Buttons to select

your digits according to its flashing digit position.

3. Press PLAY/PAUSE Button to play your desired track after repeating the

above selection procedures.

Notes: This function is not compatible with normal CD.

REMOVING THE DISC

1. After pressing the STOP button, wait for the disc to

stop rotating before sliding the DOOR OPEN switch

to remove the disc.

2. Hold the disc by the edge while slightly pressing on

the center spindle, then lift from the edge to release

and remove the disc.

HANDLING COMPACT DISCS

The DMP-CD100 is designed to

play CD/CD-R bearing the correct

identification logos. Other discs

may not conform to the CD/CD-R

standard and may not play properly.

Dirty, scratched or warped discs

may cause skipping or noise.

Handle the disc only by the edges.

To keep clean, do not touch its

surface. Discs should be stored in

their cases after use to avoid serious scratches. Do not expose discs to direct

sunlight, high humidity, high temperatures, or dust etc. Prolonged exposure

to extreme temperatures can warp the disc. Do not stick or write anything on

either side of the disc. Sharp writing instruments, or the inks used in some

felt-tip pens, may damage its surface.

CLEANING DISCS

Fingerprints should be carefully wiped from the surface

of the disc with a soft cloth. Unlike unconventional

records, compact discs have no grooves to collect dust

and microscopic debris, so gently wiping them with a

soft cloth should remove most particles. Wipe in a

straight motion from the center to the edge. Never use

thinner, benzene, record cleaner or anti-static spray on

a compact disc. Such chemicals can damage its plastic

surface.

TROUBLESHOOTING GUIDE

Check the following guide for problem resolution.

SYMPTOM CAUSE SOLUTION

CD Player will not

turn on

Hold Switch position is

“ON”.

Dead or weak batteries.

AC adaptor not

connected properly.

Turn the Hold Switch to the

“OFF” position.

Replace batteries.

Check AC adaptor

connection.

Disc will not play Disc inserted incorrectly.

Defective compact disc.

CD compartment not

closed.

Moisture has formed

inside the CD deck.

Reinsert disc with label side

facing up.

Try another compact disc.

Close lid securely.

Take out the CD and leave

the CD compartment door

open for about an hour to dry

moisture condensation.

No sound from

headphones

Headphone plug not

inserted properly.

Volume control set to

minimum.

Weak batteries.

Defective compact disc.

Reinsert headphone cord into

Headphone jack.

Increase the volume.

Replace with fresh batteries

or use AC power.

Try another compact disc.

Sound is skipping The compact disc or

pickup lens is dirty.

Strong vibrations.

Clean or replace the compact

disc or clean the pickup lens.

Place the CD player on a

level surface that is stable (no

vibrations).

SPECIFICATIONS

• 1 Bit D/A Converter.

• Digital Filter 8 Times Over-sampling.

• Auto CD/MP-3 Detectable (reads CD/CD-R).

• 3 Spot Optical Pick-up.

• Up to 22 Selected Music Storing Ability.

• Up to 255 Music Selection of MP-3 Mode.

• Fast Track Selector in MP-3 Mode.

• Continue/ Intro/ Single Music/ Program/ Random Play Mode.

• Repeat Function.

• Bass Boost.

• Audio Line Out.

• Rechargeable Battery Function.

Power Source :

AC Adapter : Input 4.5V - 8V or Battery : DC 3V (AA1.5V x 2).

Headphone Output Power :

15mW (TYP).

Size of Unit :

136mm x 155mm x 29.5mm (W x D x H).

Net Weight of Unit :

200g.

**THE SPECIFICATION IS SUBJECT TO CHANGE WITHOUT PRIOR NOTICE**

Offices

AUSTRALIA D-LINK AUSTRALASIA

Unit 16, 390 Eastern Valley Way, Roseville, NSW 2069, Australia

TEL: 61-2-9417-7100 FAX: 61-2-9417-1077

TOLL FREE: 1800-177-100 (Australia), 0800-900900 (New Zealand)

URL: www.dlink.com.au E-MAIL: [email protected], [email protected]

CANADA D-LINK CANADA

2180 Winston Park Drive, Oakville, Ontario L6H 5W1 Canada

TEL: 1-905-829-5033 FAX: 1-905-829-5095 BBS: 1-965-279-8732 FREE CALL: 1-800-354-6522

URL: www.dlink.ca E-MAIL: [email protected]

CHILE D-LINK SOUTH AMERICA

Isidora Goyenechea #2934 of.702, Las Condes, Santiago, Chile

TEL:56-2-232-3185 FAX: 56-2-2320923 URL: www.dlink.cl

E-MAIL: [email protected], [email protected]

CHINA D-LINK CHINA

2F., Sigma Building, 49 Zhichun Road, Haidian District, 100080 Beijing, China

TEL: 86-10-88097777 FAX: 86-10-88096789

URL: www.dlink.com.cn

DENMARK D-LINK DENMARK

Naverland 2, DK-2600 Glostrup, Copenhagen, Denmark

TEL:45-43-969040 FAX:45-43-424347 URL: www.dlink.dk

E-MAIL: [email protected]

EGYPT D-LINK MIDDLE EAST

7 Assem Ebn Sabet Street, Heliopolis Cairo, Egypt

TEL: 202-2456176 FAX: 202-2456192 URL: www.dlink-me.com

E-MAIL: support@dlink-me.com, fateen@dlink-me.com

FRANCE D-LINK FRANCE

Le Florilege #2, Allee de la Fresnerie

78330 Fontenay Le Fleury France

TEL: 33-1-30238688 FAX: 33-1-3023-8689 URL: www.dlink-france.fr

E-MAIL: info@dlink-france.fr

GERMANY D-LINK GERMANY

Schwalbacher Stra_e74, 65760 Eschborn, Germany

TEL: 49-6196-77990 FAX: 49-6196-7799300

URL: www.dlink.de BBS: 49-(0)6192-971199 (Analog) 49-(0)6192-971198 (ISDN)

INFO LINE: 00800-7250-0000 (toll free) HELP LINE: 00800-7250-4000 (toll free)

REPAIR LINE: 00800-7250-8000 E-MAIL: [email protected], [email protected]

INDIA D-LINK INDIA

Plot No.5, Kurla-Bandra Complex Road,

Off Cst Road, Santacruz (E), Bombay - 400 098 India

TEL: 91-22-652-6696 FAX: 91-22-652-8914 URL: www.dlink-india.com

E-MAIL: [email protected]

ITALY D-LINK ITALIA

Via Nino Bonnet No. 6/b, 20154 Milano, Italy

TEL: 39-02-2900-0676 FAX: 39-02-2900-1723 URL: www.dlink.it

E-MAIL: info@dlink.it

JAPAN D-LINK JAPAN

10F, 8-8-15 Nishi-Gotanda, Shinagawa-ku, Tokyo 141 Japan

TEL: 81-3-5434-9678 FAX: 81-3-5434-9868 URL: www.d-link.co.jp

E-MAIL: kida@d-link.co.jp

RUSSIA D-LINK RUSSIA

Michurinski Prospekt 49, 117607 Moscow, Russia

TEL: 7-095-737-3389, 7-095-737-3492 FAX: 7-095-737-3390

E-MAIL: [email protected]

SINGAPORE D-LINK INTERNATIONAL

1 International Business Park, #03-12 The Synergy, Singapore 609917

TEL: 65-774-6233 FAX: 65-774-6322

URL: www.dlink-intl.com E-MAIL: [email protected]

S. AFRICA D-LINK SOUTH AFRICA

Unit 2, Parkside 86 Oak Avenue

Highveld Technopark Centurion, Gauteng, Republic of South Africa

TEL: 27(0)126652165 FAX: 27(0)126652186 CELL NO: 0826010806 (Bertus Moller)

CELL NO: 0826060013 (Attie Pienaar) E-MAIL: bertus@d-link.co.za, attie@d-link.co.za

SWEDEN D-LINK SWEDEN

P.O. Box 15036, S-167 15 Bromma Sweden

TEL: 46-(0)8564-61900 FAX: 46-(0)8564-61901 E-MAIL: [email protected]

URL: www.dlink.se

TAIWAN D-LINK TAIWAN

2F, No. 119 Pao-Chung Road, Hsin-Tien, Taipei, Taiwan, R.O.C.

TEL: 886-2-2910-2626 FAX: 886-2-2910-1515 URL: www.dlinktw.com.tw

E-MAIL: [email protected]nktw.com.tw

U.K. D-LINK EUROPE

Floor, Merit House, Edgware Road, Colindale, London, NW9 5AB, U.K.

TEL: 44-20-8731-5555 FAX: 44-20-8731-5511

URL: www.dlink.co.uk E-MAIL: [email protected]

U.S.A. D-LINK U.S.A.

53 Discovery Drive, Irvine, CA 92618 USA

TEL: 1-949-788-0805 FAX: 1-949-753-7033 INFO LINE: 1-800-326-1688

BBS: 1-949-455-1779, 1-949-455-9616

URL: www.dlink.com E-MAIL: [email protected], [email protected]

Tech Support Hours: 6 A.M. to 6 P.M. Pacific Standard Time. Monday through Friday

Page is loading ...

D-Link DMP-CD100 User manual

Brand: D-Link

Model: DMP-CD100

Category: CD players

Type: User manual

Download PDF

report

D-Link DMP-CD100 User manual

D-Link DMP-CD100 User manual

Related papers

Other documents