Sea gull lighting 16004-15 User guide

Sea gull lighting
Brand
Sea gull lighting
Model
16004-15
Category
Household fans
Type
User guide
16004-15
1. Model CD-52, manufactured by Ja Yang (E106510)
16004-15
Top view of switch housing plate.
2
Disconnect Molex Connectors in switch housing
plate by pushing down on tab and pulling the
two (molex connectors) apart.
3
CAUTION: To reduce the risk of electric shock,
install only in Fan
CAUTION : FOR CONTROL OF SHADE POLE, PERMANENT SPLIT
CAPACITOR, OR UNIVERSAL MOTORS ONLY.
Connect the molex from the receiver to the
molex in the switch housing plate b
y aligning
and sliding together. Note: For longer distance
operation, coil receiver antenna around the
natural wire (white wire).
4
Align gap in receiv
er with the screw between
speed switch and reverse switch and slide
receiver (Dip switch facing housing plate) into
switch housing plate. R
eceiv
er should fit direct
-
ly into area in the switch housing plate. Note:
If installing light kit, use the blue and white
wire from the receiver.
6
Set dip switches on the R
emote T
r
ansmitter and
Remote Receiver to the same settings. This
must be done so the units will communcate
properly. If you have other fans you can set to
control from one tr
ansmitter b
y setting both
receivers the same as the transmitter. If you
ha
v
e more than one fan with remote. You can
set the dip switches to different positiosns to
have seperate control.
Remote Transmitter Dip swtiches
Remote Receiver Dip switches
5
2. Model 9701, manufactured by Furn Fan (E141261)
3. Model AC-552, manufactured by Air Cool (E75795)
Caution: T
urn off power at fuse box to avoid
possible electrical shock.
1
INSTRUCTIONS FOR YOUR NEW
REMOTE FAN CONTROL SYSTEM
16004-15
The wall control transmits the command signals via radio waves to the receiver
installed in the fan’s hanging bracket or on the fan. The receiver is required for
the wall control to function. Power for the wall control comes from the 12V bat-
tery located in the wall remote. Duracell MN21 / Eveready A23 / GP 23A all 12V.
The frequency switches (dip switches) on the wall control and the receiver have
been preset at the factory. Please recheck to make sure the switches on the wall
control and receiver are set to the same position. Any combination of settings are
fine as long as the wall control and ceiling fan receiver are set to the same posi-
tion.
CAUTION: TURN OFF POWER AT FUSE BOX TO AVOID POSSIBLE ELECTRICAL SHOCK.
Install wall control unit to outlet box
using machine screws provided.
3
Attach front cover to wall control
with screws provided. Snap battery
cover in place.
4
Remove cover by snaping off from top or bot-
tom. Remove battery cover. Install 12V battery
into wall remote. Duracell MN21 / Eveready A23
/ GP 23A all 12V.
Place face plate over battery compartment and
buttons. Place remote over 2 pins on front
cover. Attach cover of remote by placing over 4
pins and snaping into place.
2
1
HAND HELD INSTALL
W
ALL MOUNT INSTALL
16004-15
Remote Control Transmitter Features:
FAN SPEED Depress “l dot” for low speed, “2 dots” for medium or “3 dots” for
high. To turn fan off press square”.
LIGHT DIMMER To turn light on, press light dimmer once quickly. To turn off
press once quickly while light is on. To dim light hold down button “light dimmer”.
The light will cycle from bright to dim to bright until button is released. Light will
maintain last setting if turned off.
FORWARD/REVERSE Depress rev button allow a few seconds for remote to
change rotation direction.
HIGH SPEED
M
EDIUM SPEED
LOW SPEED
F
AN OFF SETTING
(
Turns fan off only)
F
orward/Reverse
(
Press once to
change direction of
t
he fan.
LIGHT ON/OFF SET-
T
ING AND DIMMER
(
Press and hold to
dim light infinitively)
L
ED LIGHT
For Customer Service Call
866-449-2821
  • Page 1 1
  • Page 2 2
  • Page 3 3

Sea gull lighting 16004-15 User guide

Sea gull lighting
Brand
Sea gull lighting
Model
16004-15
Category
Household fans
Type
User guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents