Kenmore 758.14417 User manual

Brand: Kenmore

Model: 758.14417

Category: Humidifiers

Type: User manual

This manual is also suitable for

Save this manual

for future reference

S_EA/ S

owner's

manual

Stock No.

42-14417

Model No.

758.144170

FOR YOUR

SAFETY:

READ

ALL INSTRUCTIONS

CAREFULLY

QUIETCOMFORT

WHOLE HOUSE

HUMIDIFIER

13 Gallon Output

Innovative Twin Fan

Technology

• Operating Instructions

• Parts List

Sears, Roebuck and Co, Hoffman Estates, IL 60179 US.A.

Part No. SP6424 Printed in Canada

• FULL ONE YEAR WARRANTY ON HUMIDIFIER

If within one (1) year from the date of purchase, this humidifier fails due to a defect in

material or workmanship, Sears will repair it, free of charge. If within two (2) years from

the date of purchase, the motor fails due to defect in material or workmanship, Sears

will repair it free of charge.

This warranty service is available by simply returning the humidifier to the nearest Sears

Service Center/Department throughout the United States.

This warranty applies only while this product is used in the United States

This warranty gives you specific legal rights, and you may also have other rights which

vary from state to state.

Ib., Sears, Roebuck and Co., D/817 WA, Hoffman Estates, IL 60179 ..,

GENERAL SAFETY INSTRUCTIONS

Safety Signal Words 4. Keep the humidifier clean.

DANGER: means if the safety information

is not followed, someone will be seriously

injured or killed.

WARNING: means if the safety information

is not followed, someone could be serious-

ly injured or killed.

CAUTION: means if the safety information

is not followed, someone may be seriously

injured or killed.

1. To reduce the risk of fire or shock hazard,

plug humidifier directly into a 120V, A.C. elec-

trical outlet. Do not use extension cords.

2. Keep the electric cord out of traffic areas.

To reduce the risk of fire hazard, never put

the electric cord under rugs, near heat

registers, radiators, stoves or heaters.

3. Always unplug the humidifier before

moving it, before cleaning, or whenever

the humidifier is not in service.

Table of Contents

Warranty Information .................................. 2

General Safety Instructions ........................ 2

To Save A Service Call ............................... 2

Know Your Humidifier ................................. 3

Humidifier Operations ................................ 4

Assembly .................................................... 4

Location Instructions ............................... 4-5

Electrical Hook-Up ...................................... 5

To Save a Service Call

Check the following if your humidifier will

not operate.

1. Is power cord attached to outlet?

2. Is there electrical power to outlet?

5. Do not put foreign objects inside the

humidifier.

6. Never use your humidifier while any part

is missing or damaged in any manner.

7. To reduce the risk of electrical hazard or

damage to humidifier, do not tilt, jolt or

tip humidifier while unit is running.

8. To reduce the risk of damage to humidi-

fier, unplug humidifier, when water bot-

tles are empty or when the humidifier is

not in use.

9. To reduce the risk of accidental electri-

cal shock, do not touch the cord or con-

trois with wet hands.

10.Note the warning label shown below.

WARNING: To reduce risk of fire, elec-

tric shock, or injury always unplug

beforef ng, servcngorceanng.

Water Fill .................................................. 5-6

Operating Humidifier Controls ................... 7

Manual Dryout ............................................. 7

Using Your Humidifier ................................. 8

Operating Tips for Best Performance ......... 8

Replacement and Care of Filters ........... 9-10

Cleaning Your Humidifier ..................... 11-12

Troubleshooting ....................................... 13

Repair Parts ......................................... 14-15

3. Is airflow control in operating position?

4. Is humidity control set high enough?

5. Is the cabinet sitting on a level surface?

Know Your Humidifier

Control Panel Cover & Pivoting Lid Removed for Clarity

Controls

Fan Assembly

Bottles

Pivoting

Lid

Filter

Housing

Filters:

Replacement

Filter 42-14911

Description

Gallon Output/24 Hrs.

Capacity of Bottles

Sq. Ft. Coverage

Fan Speeds

Filters

Independent Bottle Gauges

Fill Indicator

42-14417

2-3/8 Gallons Each

*2700

Set of 4 (42-14911 )

Yes

Yes (Independent Bottle)

Automatic Shutoff

Automatic Humidistat

Controls

CUL Listed

Volts

Hertz

Amps

Watts

Yes

Rotary

Yes

120 A.C.

2.88

165

Based on an area with average insulation and

an 8 foot ceiling height.

Humidifier Operations

Your new Sears humidifier is designed to

satisfy home humidity requirements

through the principle of evaporation of

water in the air.

After water is added to the bottle, the fil-

ters begin to soak up the water and

become totally saturated in approximately

30 minutes. Air is drawn in from the rear of

the humidifier and through the filters by

means of circulation fans. As air passes

through the filters, moisture is absorbed

into the air and then released in the form

of vapor. No water droplets will enter the

home. All evaporation into the air takes

place in the humidifier, which means that

the residue left by evaporating water is not

passed into the home, but remains in the

Humidified Air is

Then Released

Through the Top

Dry Air Enters

ra;Ugh

filter.

CAUTION: Use only 42-14900 EPA

Registered Bacteriostat available

from SEARS Retail store, Under no

circumstances should you use water I

treatment products designed for Roto

be t or U trason c hum d fers.

Assembly

Your new Sears Kenmore humidifier is com-

pletely assembled for you to use. Remove

the bag pack containing two plastic caster

pads from top of humidifier and retain for

future use if required. See step 1 below for

instructions. Remove the packaging materi-

CAUTION: To reduce the risk of injury,

fire or damage to humidifier, use only

cleaners specifically recommended

for humidifiers. Never use flammable,

combustible or poisonous materials to

clean your humidifier. To reduce the

risk of scalds and damage to humidifi-

er, never put hot water in humidifier.

al from inside your humidifier and follow the

instructions of this owner's manual for prop-

er usage. The packaging material is located

under the fan assembly. Remove the pack-

aging material and discard.

Location Instructions

WARNING: For your own safety, do not

use humidifier if any

parts are damaged

or m ss ng.

Step 1

Place humidifier on a flat level surface in an

area of your house where humidity is need-

ed most, or an area which would likely result

in moist air being circulated throughout the

house, such as near a cold air return.

Placing the unit level is very important if the

humidifier is located on carpeting.

NOTE: The 13 gallon humidifier contains

water bottles. The weight of the bottles in

the front of the cabinet may cause the front

casters to sink deeper into the carpet. If this

happens, the water level will be higher

towards the front of the humidifier, and

lower towards the back. The water level

float (located at the rear of the cabinet) may

not sense the water so the fill light will be on

and the unit will not energize. If this hap-

pens, the unit will need to be leveled in

order for the humidifier to be energized. To

level the humidifier when located on carpet

place the included caster pads under the

front two casters of the humidifier only. See

diagram page 5.

Location Instructions

NOTE: Due to release of cool, moist air

from humidifier, it is best to direct air away

from home thermostat and hot air registers.

It is best to position humidifier next to an

inside wall. Hot air registers and cold air

from outside walls can affect the efficiencies

of the controls. Unit should not be placed

where warm air from a hot air register blows

directly on unit.

Moist air (humidity) produced will disperse

into the whole house, but area closest to the

unit will have the highest humidity. If the unit

is positioned close to a window, condensa-

tion may form on the window pane. If this is

not appropriate the unit should be reposi-

tioned in another location.

Electrical Hook-Up

Locate nearest 120V A.C. wall socket in

the location desired, preferably on inside

wall. Plug in the electrical cord.

WARNING: To reduce the risk of fire

or shock hazard, humidifier should

be plugged into a 120V A.C. outlet. Do

not use extension cords

To reduce the risk of electrical shock, this

humidifier has a polarized plug (one blade

is wider than the other). This plug will fit in

a polarized outlet only one way. If the plug

does not fit fully in the outlet, reverse plug.

Water Fill

(continued)

Step 2

The humidifier should be positioned with the

back (cord exit side), at least 2 inches away

from the wall. Air needs to enter through the

Iouvres in the rear panel in order for the

humidifier to operate at peak efficiency.

At Least 2" From Wall

_ Caster Pad

_-_ Carpet

Surface

NOTE: If positioning on

carpet, place caster pads

under front casters only

.... _=E-'-to level (if necessary).

If it still does not fit, contact a qualified

electrician to install the proper outlet. Do

not change the plug in any way.

WARNING: To reduce the risk of shock,

always unplug humidifier before clean-

ing or servicing.

WARNING: To reduce the risk of fire or

shock hazard, do not pour or spill water

into control or motor area. Close the

control cover. If controls get wet, let

them dry completely and have unit

checked by an authorized service per-

sonnel before plugging in.

This humidifier is designed for use with the

two water bottles that are located under the

pivoting lid.

Open the pivoting lid of the humidifier.

Remove the water bottles by lifting them

straight up and out of the cabinet.

Fan Assembly

Bottles

/ Pivoting

Lid

Water Fill (continued)

Notice the water bottles are designed as

right and left hand units. Position them in the

correct location so the humidifier can func-

tion properly. The water bottles should rest

in the front of the cabinet. Each "E-Z-Fill

Side-Cap" must be facing the rear of the

unit.

Each water bottle is designed with an "E-Z-

Fill Side-Cap" that is easily removable.

Remove the "E-Z-Fill Side-Cap" on the side

of the water bottle by twisting counterclock-

wise.

Place the opening of the water bottle under

a water faucet (the bottle should fit under a

four-inch clearance faucet). Fill with recom-

mended mixture of cold water and Sears

Bacteriostat #42-14900 (if necessary) only.

Solid debris could make the valve leak.

Install the "E-Z-Fill Side-Cap" by twisting

clockwise. Hand tighten only.

Check for possible leaks by performing

the following:

1. Grasp bottle handle and hold the bottle

upright over a sink.

2. Press up on valve cap plunger for about

one second to let out a little water.

3. Release the plunger.

4. Listen for air bubbles. Look for leaks

around the "E-Z-Fill Side-Cap".

5. if you hear air bubbles or see leaks,

retighten the "E-Z-Fill Side-Cap" and

repeat steps 1-4.

Wipe off excess water from the bottle.

Position the water bottle back into the unit by

grasping the water bottle handle and lower it

into the cabinet until the bottle sits on pads

at bottom of cabinet. The "E-Z-Fill Side-Cap"

must be facing the rear of the cabinet. When

positioned properly, the plunger will open

and water will flow into the cabinet. The

water level will automatically remain at

approximately 1/2" until the bottles are

empty.

Allow the filters to saturate for 30 minutes

before operaton.

Note: Ensure that the raised section of the

water bottle falls into the hole in stationary

lid in order for the bottle gauges to function

properly.

-...j

"E-Z-Fill Side-Cap"

Should Always Face Rear

Rear of

Humidifier

Turn Counterclockwise

to Remove Cap

Valve

Cap Plunger

Pivoting Lid

Removed

for Clarity

Raised

Stationary Section

LidjHol

Operating Humidifier Controls

The operating controls of your Kenmore

Quiet Comfort whole house humidifier are

located on the top center of the humidifier.

The controls are found under the smoked

control cover, located between the air circu-

lating fans.

Lift the control cover by placing your finger

in the round cutout and lifting. The cover will

stay open. Now you can clearly see the con-

trol area. Familiarize yourself with the con-

trols and reference the diagram of the con-

trol area for the correct naming used in this

manual.

To Operate the Controls

Humidity Control: O

Adjust the amount of humidity depending on

your needs. The humidifier will turn on and

off as required to maintain level of humidity

selected. A medium setting is recommend-

ed, but there are times when low or high

amount of humidity may be preferred. For

constant operation of humidifier, rotate

humidity knob all the way clockwise. This

allows for the maximum amount of humidity

to be evaporated into the air continuously.

IMPORTANT: Water damage may result if

condensation starts to form on windows or

walls. Humidity Control setting should be

lowered until condensation no longer forms.

Speed Control O

The unit is adjusted from off " | " to high

" " " " " with a rotary speed control. The

higher the air flow speed, the more water is

evaporated and released into the air. Low

speed" "" is the quietest and is provided for

conditions that may not require as high an

evaporation rate.

VIS-FILL Water Bottle Gauges and

Fill Lights

This humidifier is equipped with indepen-

dent (left and right) water level bottle

gauges. When the unit is energized the cen-

ter area of the control panel containing the

gauges and fill indicators will illuminate red

to depict the operation mode. The right bot-

tle as viewed from the front of the humidifier

will always empty first. As it empties the

number of red bars will decrease. When it is

totally empty the Fill Indicator immediately

beside the bars will illuminate. NOTE: The

humidifier will not shut off at this stage.

Once the right bottle empties, the humidifier

will begin to use the water from the left bottle

until it is depleted. At this time the Fill

Indicator beside it will illuminate. There will

still be a slight delay in the unit shutting off

while it depletes the water in the bottom of

the cabinet. At this time or anytime during

normal operation you may fill the water bot-

tles to continue operation. Note: A small

amount of water remains in cabinet after both

Fill Indicators turn on and the unit shuts off.

Left

Bottle _ Right

Gauge Bottle

Left Bottle Right Gauge

Fill Indicator Bottle

Fill Indicator

Manual Dryout

At the end of the humidification season or if

you do not plan to run the humidifier for one

week or more, you can override the auto-

matic shutoff function to completely dry the

humidifier cabinet out.

To do this, simply slide the float retainer locat-

ed at the back of the humidifier cabinet to the

top position of the slot it is located in. This will

hold the float in an upward position and the

fans will run until you turn the power off.

NOTE: Be sure to position float retainer to

the normal operating mode (lowest position

in slot) for humidifier operation.

Below is a diagram of the slot the float retain-

er is located in at the back of the cabinet.

Back of Cabinet

TOP POSITION

IS FOR MANUAL

DRYOUT

BOTTOM POSITION

IS FOR NORMAL

OPERATION MODE

FLOAT

RETAINER

SLOT

Using Your Humidifier

Step 1

Be sure humidifier is full of water and

plugged in.

Step 2

Set Speed Control _ to low speed " ° "

Step 3

Set Humidity Control " _ " to medium

position.

NOTE: Humidifier should operate with

humidity control on the recommended

medium setting, if it does not, the humidity

is at a relatively high level. To test the unit

under this condition, turn Humidity Control

all the way to clockwise and unit should

begin to operate. After the unit has been

tested, set Humidity Control to medium or

desired level.

Allow 24 hours for humidifier to adjust.

If humidity level in home is sufficient, the

humidifier will only operate with Humidity

Control turned all the way clockwise.

IMPORTANT: Water damage may result if

condensation starts to form on windows or

walls. Humidity Control setting should be

lowered until condensation no longer

forms.

Step 4

If humidifier stops running and BOTH Fill

indicators are not on, the humidity level is

at the normal requirements for that setting

or it is adjusting to the home conditions.

The chart below shows recommended

indoor humidity levels.The figure below

shows approximate relative humidity per-

centages which correspond to the various

settings of the Humidity Control.

Recommended

When Outdoor Indoor Relative

Temperature is: Humidity is:

-10°F 20%

0°F 25%

10°F 30%

20°F & above 35%

Relative Humidity

Operating Tips for Best Performance

1. Position the humidifier at least 2 inches

from any wall and away from any heat

registers.

2. Do not restrict airflow from entering or

exiting the humidifier.

3. Use Sears recommended bacteriostat

42-14900 to retard bacteria growth that

may cause odors and may be harmful

to your health.

4. Perform regular cleaning as instructed

in "Cleaning Your Humidifier" section of

this manual.

5. Replace the evaporative wicking filters

at least once per humidification season

or more depending on water conditions

in your area.

Replacement and Care of Filters

WARNING: To reduce the risk of shock

or injury from moving parts, always

unplug humidifier before removing or

replacing any parts.

CAUTION: To help retard bacteria

growth and keep maximum efficiency,

the filters should be replaced at least

once per season, or more often under

hard water conditions. Use Sears rec-

ommended replacement filter 42-14911.

The filters may be rinsed periodically in clear

water only. Take care not to damage paper.

To replace evaporative wicking filters in your

Kenmore Quiet Comfort Whole House

humidifier, follow the instructions below.

1. Unplug humidifier and proceed to clean.

Before removing the filters, we recom-

mend moving the humidifier to an area

where floor coverings are not suscepti-

ble to water damage, i.e. kitchen or bath

areas.

2. Open the pivoting lid and remove water

bottles and set aside. Grasp the fan

assembly front center and rear center.

Lift off and set aside on a clean flat sur-

face. The filter housings are now acces-

sible.

3. Lift filter housing out of cabinet and place

where you may work on them comfort-

ably. With a soft, absorbent cloth remove

any remaining water or loose mineral

deposits not trapped in the filter from the

humidifier cabinet.

4. To open filter housing for easy access to

filters:

a. Deflect the two spring tabs on top of

filter housing. Lift top cover off of the

filter housing and set aside.

b. Remove the two filters and dispose

of properly. Clean internal parts of

humidifier per the "Cleaning of

Humidifier" section of your owner's

manual.

Pivoting Lid

Front of Humidiifer

Spring Tabs

Fan Assembly

Cabinet

Filter

Replacement and Care of Filters (continued)m

c. install new filters in the filter housing

track with the glue beads of the wick-

ing pad to the inside of the filter hous-

ing.

d. Return the top cover of the filter

housing by installing the cover over

the fixed tabs on the rear of the lower

filter housing and pivoting the cover

down over the top of the filters. Snap

the cover over the two spring tabs.

e. Replace the filter housing in the cab-

inet. Note: There is a front and back

orientation. To position the filter

housings correctly: Front of

Humidifier

• Be sure that the spring tabs of filter

housings are towards front of cabi-

net.

• Align the lower portion of the filter

assembly over the six ribs located at

the bottom rear of the humidifier cab- Top

inet. Cover

f. Position fan assembly onto the cabi-

net. Make sure the fan venturi (low-

est cylinder section below the fan) is

placed inside the filter housing.

g. Replace water bottles.

h. Close the pivoting lid. Spring

i. The unit is ready for use or to be Tabs

stored away for next season.

NOTE: For correct operation of the filter

housing assembly, filters must be fully con-

tained inside the flange of the top cover.

Fixed Tabs

Spring Tabs

Filter

Rear of

Humidifier

Flat Portion of Filter Housing

Towards Back of Cabinet

Spring Tabs Towards Front of Cabinet

Step 4 e.

Cleaning Your Humidifier

WARNING: To reduce the risk of

injury, fire or damage to humidifier,

use only cleaners specifically rec-

ommended for humidifiers. Never

use flammable, combustible or poi-

sonous materials to clean your

humidifier. To reduce the risk of

scalds and damage to humidifier,

never put hot water in humidifier.

CAUTION: Local water purity varies

from area to area and under certain

conditions water impurities and air-

borne bacteria may promote the

growth of microorganisms in the

reservoir of the humidifier.

To retard bacteria growth that may

cause odors and be harmful to your

health, use only Sears replacement

filters. We also recommend using

EPA approved bacteriostat, 42-14900

and humidifier cleaner 42-14713,

available at your local Sears store.

NOTE: If it is necessary to use approved

bacteriostat, follow directions correctly.

The bottles of the whole house humidifier

will hold 2-3/8 gallons of water each.

Step 1

To make cleaning easier, the humidifier

cabinet should be empty and completely

dried out. To accomplish this, use the fol-

lowing method:

a. On the back side of the humidifier cab-

inet, find the float retainer. In normal

operating mode, the retainer will be

positioned in the bottom of the slot in

the cabinet. Push the retainer up to the

top slot position in the cabinet until it

locks in place. (See "Manual Dryout"

section on page 7.)

b. Allow the humidifier to run until there is

no water left in the cabinet.

c. Unplug humidifier.

I ARNING: If humidifier is not un- I

plugged, fan could start after housing

is removed.

Step 2

To Remove Parts

a. Open the pivoting lid and remove water

bottles and set aside. Grasp the fan

assembly front center and rear center.

Lift off and set aside on a clean fiat sur-

face. The filter housings are now

accessible.

b. Before removing the internal parts of

the humidifier cabinet, we recommend

moving the humidifier to an area where

floor coverings are not susceptible to

water damage, i.e., kitchen or bath

area. Lift the filter housing assemblies

out of the cabinet and set to the side.

c. Remove the water level float from the

humidifier cabinet by pinching the float

retainer to release it from the cabinet.

The cabinet should be empty before

cleaning. The cabinet consists of the

lower areas of the humidifier where the

filters are during normal operation time.

d. Empty cabinet of any remaining water.

e. Proceed to "Bi-Weekly Maintenance"

or "End of Season Maintenance."

f. Remove old filters and dispose of prop-

erly as described on page 9 and 10.

Step 3

Install new filters (purchase the correct

evaporative wicking filter pads 42-14911

for your humidifier) into the location where

the old filters were positioned. Install the

filter housings with the new filters into the

correct location. Reinstall the water level

float. NOTE: Float retainer should be posi-

tioned in normal operating mode. Assure

that it is positioned in the bottom of the slot

in the back of the cabinet. (See page 7 for

diagram of slot.) Position the fan assembly

on top of the cabinet and return the humid-

ifier to the desired location for use.

Refill humidifier bottles with fresh cool water

and return them to the cabinet. Plug the unit

into a 120 volt A.C. power outlet and set the

controls per the "Operating Humidifier

Controls" section of this manual.

Cleaning of Humidifier (continued)

Bi-Weekly Maintenance

Removing Scale

1. Fill the humidifier cabinet with one 8

oz. cup of undiluted white vinegar. Let

solution stay 20 minutes.

2. Clean all interior surfaces with a soft

brush. Dampen a soft cloth with undi-

luted white vinegar and wipe out the

cabinet to remove scale.

3. Rinse thoroughly with clean warm

water to remove scale and cleaning

solution before disinfecting cabinet.

4. Dust the fan assembly and outside sur-

faces with a soft cloth only.

End of Season Maintenance

1. Follow "Bi-Weekly Maintenance"

instructions at end of humidification

season.

2. Remove and throw away filters.

3. Let humidifier dry completely before

storing. Do not store with water inside

cabinet or water bottles.

4. Store in cool, dry location.

5. Install a new filters in clean humidifier

before next season begins.

6. "Bi-Weekly" is also recommended if

you do not plan to run the humidifier for

one week or more.

Disinfecting Humidifier Cabinet

and Water Bottles

1. Fill humidifier cabinet with 1 teaspoon

chlorine bleach in 1 gallon of water. Let

solution stay for 20 minutes, swishing

every few minutes. Wet all surfaces

normally exposed to water.

2. Empty humidifier cabinet after 20 min-

utes. Rinse with water until bleach

smell is gone. Allow unit to dry out

completely.

3. Water bottles should be cleaned in the

same manner.

Troubleshooting

Trouble Probable Cause Remedy

Unit will not run and no • No Power. • Check 120 volt power

control panel lights are source.

illuminated.

Unit will not shut off. • Float retainer is positioned • Slide float retainer down to

in "Manual Dryout" position, normal operation mode.

Refer to "Manual Dryout"

section on page 7.

• Free float from obstruction.

Unit will not dry out

completely.

Bottles continue to empty.

Neither bottle emptying.

Left bottle not emptying.

Fill Indicators turn on before

bottles are empty.

Note: There may be a little

water still in bottle when Fill

indicator is illuminated. This

is normal.

• Float is not free.

• Float is positioned in

normal operation mode.

• Air is entering water bottles.

• Bottle cap plunger missing

post in bottom of cabinet

• Dirty filters

• Right bottle contains water

• Unit is not set up on a level

surface. (Float will not

sense water at the rear of

the cabinet.)

• This is normal. A small

amount of water remains in

the cabinet after Fill Lights

come on, Position float

retainer in "Manual Dryout"

position to completely dry out.

See page 7.

• Check "E-Z-Fill Side-Caps"

and valve assembly caps to

ensure tightness.

• Check for leak in water bottles.

• Ensure gaskets for "E-Z-Fill

Side Caps" are in place.

• Check orientation of bottles.

Reposition so that bottle cap

plunger (stem) is depressed

by post in bottom of cabinet,

• Change to fresh new filters.

(42-14911)

• The humidifier is designed so

the right bottle empties first.

Continue to run until both fill

lights come on.

• Position unit level. (Some

carpet padding may allow

unit to sit lower in front than

rear with the additional

weight of water bottles in

the front of the cabinet.

Install caster pads under

front casters. (See page 4),

CAUTION: Use only 42-14900 EPA Registered Bacteriostat available from Sears Retail

store.

Use of other water treatment products may damage the filter elements.

Under no circumstances should you use water treatment products designed for Roto

belt or Ultrasonic humidifiers.

Key Part No. Description

No.

828743

828756

828853

828741-1

828855-1

822409

823912

828753

828755

828750

828751

828752

828749

828854

824690

828192

828726

509229-1

828199-9

Cover, Dust

Knob

Label, Control

Lid, Stationary

Lid, Pivoting

Humidistat

Switch, Rotary

Cover, Actuator Arm

Spring, Compression

Light, Pilot

Arm, Lli Actuator

Arm, RH Actuator

Retainer, Micro Switch

Switch, Micro

'Easy-Fill Side-Cap"

Bottle, Left (Includes Key No'st5 & t8)

Bottle, Right (IncludesKey No's 15& 18)

Cap, Valve Assembly

Cabinet

* Standard Hardware Item - May be purchased locally.

Key Part No. Description

No.

20 823726

21 STD601107

22 828515

23 823849

24 42-14911

25 828197

26 828534

27 828115-1

28 822406-1

29 828196

30 828858

31 816069-5

32 816069-6

33 STD600805

34 824101-1

35 828200

36 828745

37 828920

- SP6424

Rail, Kick

* Screw, Pan lid. Ty "AB" #10 x 3/4

Caster, Twin Wheel

Support, Filter Lower

1"Filter, Evaporative

Support, Upper Filter (Leftt)

Support, Motor

Motor (includes mounting hardware)

Fan

Support, Upper Filter (Right)

Cord w/Plug

* Screw, Pan lid. Ty "AB" #6 x 1/2

* Screw, Pan Hd. Ty "AB" #6 x 3/4

* Screw, Pan lid. Ty "AB'"' #8 x 1t2

Retainer, Float

Float, Water Level

Enclosure, Electronics

Pad, Caster (Two)

Owner's Manual (not illustrated)

t Stock Item - May Be Secured Through Sears Retail

and Catalogue Stores.

_r-

€-

Fortherepair or replacementparts youneed

Call7 am - 7 pm, 7 daysaweek

1-8OO-366-PART

(1-800-366-7278)

Forin-homemajor brandrepairservice

Call24 hours a day,7 days aweek

1-800-4-REPAIR

(1-800-473-7247)

Forthe locationof a Sears RepairService

Centerinyourarea

Call24 hours a day,7 days aweek

1-800-488-1 222

Forinformationonpurchasing a Sears

MaintenanceAgreementorto inquire

aboutan existingAgreement

Call9 am - 5 pm, Monday-Saturday

1-800-827-6655

SEARS

America's Repair Specialists

The modelnumberwill be found on the Humidifier identificationlabel.

Whenrequestingservice or orderingparts, always provide the followinginformation:

• Product Type • Model Number

• Part Number • Part Description

Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.

Part. No. SP6424 Form. No. SP6424 Printed in Canada 06/01

Kenmore 758.14417 User manual

Brand: Kenmore

Model: 758.14417

Category: Humidifiers

Type: User manual

This manual is also suitable for

Download PDF

report

Kenmore 758.14417 User manual

This manual is also suitable for

Kenmore 758.14417 User manual

Related papers

Other documents