Marcy IGS-6201 Owner's manual

  • Hello! I am an AI chatbot trained to assist you with the Marcy IGS-6201 Owner's manual. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
IRON GRIP STRENGTH
DUAL STATION HOME GYM
IGS-6201
IMPEX
®
FITNESS PRODUCTS
14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746
Tel: (800) 999-8899 Fax: (626) 961-9966
www.impex-fitness.com
NOTE:
Please read all instructions
carefully before using this
product
Table of Contents
Safety Notice
Hardware Pack
Assembly Instruction
Parts List
Resistance Chart
Warranty
Ordering Parts
Model
IGS 6201
Retain This
Manual for
Reference
01-04-08
OWNER'S
MANUAL
TABLE OF CONTENTS
BEFORE YOU BEGIN...................................................................................... 1
IMPORTANT SAFETY NOTICES..................................................................... 2
HARDWARE PACK……….....…....................................................................... 4
ASSEMBLY INSTRUCTIONS...............................................................…..........10
EXPLODED DIAGRAM……………………………………………………………….40
PARTS LIST…………………………………………………………….……….…….41
RESISTANCE CHART………………………………………………………………. 43
WARRANTY.................................................................................................… 44
ORDERING PARTS......................................................................................... 44
BEFORE YOU BEGIN
Thank you for selecting the IRON GRIP STRENGTH IGS-6201 HOME GYM by
IMPEX
®
FITNESS PRODUCTS. For your safety and benefit, read this manual
carefully before using the machine. As a manufacturer, we are committed to
provide you complete customer satisfaction. If you have any questions, or find
there are missing or damaged parts, we guarantee you complete satisfaction
through direct assistance from our factory. To avoid unnecessary delays, please
call our TOLL-FREE customer service number. Our Customer Service Agents will
provide immediate assistance to you.
Toll-Free Customer Service Number
1-800-999-8899
Mon. – Fri. 9 a.m. – 5 p.m. PST
www.impex-fitness.com
1
IMPORTANT SAFETY NOTICE
PRECAUTIONS
This exercise machine is built for optimum safety. However, certain precautions apply
whenever you operate a piece of exercise equipment. Be sure to read the entire manual
before you assemble or operate your machine. In particular, note the following safety
precautions:
1. Keep children and pets away from the machine at all times. DO NOT
leave children unattended in the same room with the machine.
2. Only one person at a time should use the machine.
3. If the user experiences dizziness, nausea, chest pain, or any other abnormal
symptoms, STOP the workout at once. CONSULT A PHYSICIAN IMMEDIATELY.
4. Position the machine on a clear, leveled surface. DO NOT use the machine
near water or outdoors.
5. Keep hands away from all moving parts.
6. Always wear appropriate workout clothing when exercising. DO NOT wear
robes or other clothing that could become caught in the machine. Running
or aerobic shoes are also required when using the machine.
7. Use the machine only for its intended use as described in this manual. DO
NOT use attachments not recommended by the manufacturer.
8. Do not place any sharp object around the machine.
9. Disabled person should not use the machine without a qualified person or
physician in attendance.
10. Before using the machine to exercise, always do stretching exercises to
properly warm up.
11. Never operate the machine if the machine is not functioning properly.
12. A spotter is recommended during exercise.
13. Maximum user weight is 300 lbs.
CARE AND MAINTENANCE
1. Inspect and tighten all parts before using the machine.
2. The machine can be cleaned using a damp cloth and mild non-abrasive detergent.
DO NOT use solvents
WARNING: BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT YOUR
PHYSICIAN. THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE AGE
OF 35 OR PERSONS WITH PRE-EXISTING HEALTH PROBLEMS. READ ALL
INSTRUCTIONS BEFORE USING ANY FITNESS EQUIPMENT. IMPEX INC. ASSUMES
NO RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY DAMAGE SUSTAINED
BY OR THROUGH THE USE OF THIS PRODUCT.
SAVE THESE INSTRUCTIONS.
2
WARNING LABEL PLACEMENT
The warning labels have been placed on the unit in location shown. If the labels are missing or illegible,
please call customer service at 1-800-888-8899 for replacements. Apply the labels in location shown.
3
HARDWARE PACK
NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size.
4
HARDWARE PACK
NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size.
5
HARDWARE PACK
NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size.
6
HARDWARE PACK
NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size.
7
HARDWARE PACK
NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size.
8
HARDWARE PACK
9
ASSEMBLY INSTRUCTION
Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches
NOTE: It is strongly recommended two or more people assembling this machine to avoid
possible injury.
STEP 1 (See Diagram 1)
A.) Attach the Butterfly Pulley Bracket (#13) to the Main Support Frame (#1) from the bottom. Secure
it with two M10 x ¾” Allen Bolts (#94) and two Ø ¾” Washers (#107).
B.) Place the two Rubber Bumpers (#55) onto the holes on the Rear Base Frame (#4). Insert the two
Guide Rods (#20) through the Rubber Bumpers into the holes on the Rear Base Frame.
C.) Attach the Main Support Frame (#1) to the Rear Base Frame. Secure it with two M10 x 3” Allen
Bolts (#98), one Bracket (#2), four Ø ¾” Washers (#107), and two M10 Aircraft Nuts (#110).
Rotate the Guide Rods to align the holes so the bolts can go through.
D.) Install four Weight Stack Cover Brackets (#126) to the Rear Base Frame. Secure the Brackets
with four M8 x 2 ¾” Allen Bolts (#128), eight Ø 5/8” Washers (#106), and eight M8 Aircraft Nuts
(#109).
E.) Attach the Foot Plate (#15) to the front base on the Main Support Frame. Align the holes and
secure it with one M8 x 3” Allen Bolt (#93), two Ø 5/8” Washers (#106), and one M8 Aircraft Nut
(#109).
DIAGRAM 1
10
STEP 2 (See Diagram 2)
A.) Attach the Butterfly Base Frame (#3) to the Main Support Frame (#1) from the bottom.
Secure it with two M10 x 3” Allen Bolts (#98), one Bracket (#2), four Ø ¾” Washers
(#107), and two M10 Aircraft Nuts (#110).
B.) Slide fourteen Weight Plates (#73) onto the two Guide Rods (#20). Make sure all the
holes on the Weight Plates are facing the back of the machine and the grooves are all on
the bottom. Each Plate weights approximately 10 lbs.
C.) Insert the Selector Rod (#25) into the center of the stack.
D.) Slide the Selector Stem (#72) onto the Guide Rods. Secure the Selector Stem to the
Selector Rod with one M12 x 2 3/8” Allen Bolt (#83) and one M12 Aircraft Nut (#111).
E.) Attach the ring on the Weight Selector Pin (#82) onto the Selector Rod. Insert the Weight
Selector Pin into the selected hole to select the numbers of Weight Plates for exercise.
Please refer to the Weight Resistance Chart in page 43.
11
DIAGRAM 2
12
STEP 3 (See Diagram 3)
A.) Attach the Vertical Frame (#7) onto the Main Support Frame (#1). Secure it with two M10 x
2 ¾” Allen Bolts (#97), four ¾” Washers (#107), and two M10 Aircraft Nuts (#110). Do not
tighten the Nuts and Bolts yet.
B.) Attach the Upper Frame (#17) onto the two Guide Rods (#20) and the Vertical Frame.
C.) Secure the Upper Frame to the two Guide Rods with two M8 x ¾” Allen Bolts (#90) and two
Ø 5/8” Washers (#106). Do not tighten the Bolts yet.
D.) Secure the Upper Frame to the Vertical Frame with two M10 x 3” Allen Bolts (#98), one
Bracket (#2), four Ø ¾” Washers (#107), and two M10 Aircraft Nuts (#110).
E.) Securely tighten all Nuts and Bolts.
13
DIAGRAM 3
14
STEP 4 (See Diagram 4)
A.) Attach the Front Press Base (#18) to the Upper Frame (#17). Align the holes and insert the 5
7/8” Front Press Axle (#81) through the holes. Secure the Axle with one M8 x ¾” Allen Bolt
(#90), Ø 5/8” Lock Washer (#124), and Ø 5/8” Large Washer (#43) on each end of the Axle.
B.) Attach the Backrest Support Frame (#12) to the Vertical Frame (#7). Secure it with one M10 x 3
¾” Allen Bolt (#101), two Ø ¾” Washers (#107), and one M10 Aircraft Nut (#110). Use the
Backrest Support Lock Pin (#75) on the Vertical Frame to secure the Backrest Support in
Position.
DIAGRAM 4
15
STEP 5 (See Diagram 5)
A.) Insert the axle on the Left Butterfly (#8) into the left pivot on the Butterfly Base (#3) from the
bottom. Secure it with one M8 x ¾” Allen Bolt (#90), Ø 5/8” Lock Washer (#124), Ø 1 1/8” Washer
(#42), and D-shaped Washer (#29). Repeat the procedure to install the Right Butterfly (#9).
B.) Attach the Leg Press Rear Base Frame (#31) to the Main Support Frame (#1). Secure it with two
M10 x 3 ½” Allen Bolt (#100), four Ø ¾” Washers (#107), and two M10 Aircraft Nuts (#110). Do
not tighten the Nuts and Bolts yet.
DIAGRAM 5
16
STEP 6 (See Diagram 6)
A.) Attach the Front Press (#19) to the Front Press Base (#18). Align the holes. Secure it with one M12
x 7 1/8” Allen Bolt (#105), two Ø 1” Washers (#108), and one M12 Aircraft Nut (#111). Cover the
Bolt and Nut with two Cover Caps (#127). Use the Front Press Lock Pin (#76) on the Front Press to
lock the Front Press in desired position.
B.) Attach the Leg Developer (#6) to the open bracket on the Main Support Frame (#1). Secure it with
one M12 x 3 3/8” Allen Bolt (#104), two Ø 1” Washers (#108), and one M12 Aircraft Nut (#111).
Cover the Bolt and Nut with two Cover Caps (#127).
DIAGRAM 6
17
STEP 7 (See Diagram 7)
A.) Attach the Leg Press Base Frame (#38) to the bracket on the Leg Press Rear Base Frame (#31).
Secure it with two M10 x 2 ¾” Allen Bolts (#97), and two Ø ¾” Washers (#107). Securely tighten
the Nuts and Bolts previously installed in Step-6, Procedure C.
B.) Attach the Leg Press Post (#34) to the open bracket on the Leg Press Base Frame. Insert the 3
¼” Leg Press Axle (#84) through the pivot. Secure each end of the Axle with one M8 x ¾” Allen
Bolt (#90), Ø 5/8” Lock Washer (#124), and Ø 5/8” Large Washer (#43).
C.) Attach the Leg Press Backrest Support (#32) to the Leg Press Base Frame. Secure it with two
M10 x 3 ½” Allen Bolts (#100), four Ø ¾” Washers (#107), and two M10 Aircraft Nuts (#110).
18
STEP 8 (See Diagram 8)
A.) Attach the Leg Press Seat Support (#33) to the Leg Press Base Frame (#38). Secure it with four
M10 x ¾” Allen Bolts (#94) and Ø ¾” Washers (#107). Do not tighten the Bolts yet.
B.) Attach the Leg Press Seat Support to the Leg Press Backrest Support (#32). Secure it with two
M10 x 2 ¾” Allen Bolts (#97), four Ø ¾” Washers (#107), and two M10 Aircraft Nuts (#110).
C.) Securely tighten the Nuts and Bolts installed in Procedure A.
DIAGRAM 8
19
/