Dual MCP200S User manual

Dual
Brand
Dual
Model
MCP200S
Category
Car media receivers
Type
User manual

This manual is also suitable for

AM/FM/CD Marine Receiver
MD200
Charge Port
INSTALLATION/OWNER'S MANUAL
2
MD200 INSTALLATION
Preparation
Removal Keys
Mounting Sleeve
Dashboard or
Mounting Kit
Head Unit
TYPICAL MOUNTING METHOD
Please read entire manual before installation.
Before You Start
•Disconnectnegativebatteryterminal.Consultaqualifiedtechnicianforinstructions.
•Avoidinstallingtheunitwhereitwouldbesubjecttohightemperatures,suchasfrom
directsunlight,orwhereitwouldbesubjecttodust,dirtorexcessivevibration.
Getting Started
•Remove2transitscrewslocatedontopoftheunit.
•Insertthesuppliedkeysintotheslotsasshown,andslidetheunitoutofthemounting
sleeve.
•Installmountingsleeveintoopening,bendingtabstosecure.
•Connectwiringharnessandantenna.Consultaqualifiedtechnicianifyouareunsure.
•Certainvehiclesmayrequireaninstallationkitand/orwiringharnessadapter(sold
separately).
•Testforcorrectoperationandslideinto
mountingsleevetosecure.
•Snaptrimringintoplace.
3
MD200 INSTALLATION
Rear Preamp Output
Connect to amplifier RCA input
Antenna Connector
RCA Cable
(sold separately)
AMP
BLUE
BLACK
RED
YELLOW
Remote Turn-On
Connect to amplifier or power
antenna. Insulate wire if not used.
Ground
Connect to vehicle
chassis ground.
Accessory
Connect to ignition
circuit or switched 12 volt source.
Memory
Connect to battery
circuit or constant 12 volt source.
Right Front
Gray/Black (-)
Gray (+)
Left Front
White/Black (-)
White (+)
Right Rear
Violet/Black (-)
Violet (+)
Left Rear
Green/Black (-)
Green (+)
5 AMP
AGC Fuse
Wiring Diagram
* Caution-Donotattachanyspeakerleadstogroundasseveredamagewilloccur.
FUSE
Whenreplacingthefuse,
makesurenewfuseisthe
correcttypeandamperage.
Usinganincorrectfusecould
damagetheradio.
TheMD200usesone
5ampAGCfuselocated
in-line.
4
MD200 OPERATION
Control Locations
Release
Volume Knob
Mute/Power
Tune/TrackDown
Tune/TrackUp
Source
Eject
USBChargingPort
AuxiliaryInput
1
2
3
4
5
6
7
8
9
Preset 6
Preset 5
Preset4/Play/Pause
Preset3/Intro
Preset 2 / Random
Preset1/Repeat
Band
Display
Audio / Menu
10
11
12
13
14
15
16
17
18
1 2
9
TheMD200hasaneasy-to-useinterfacethatprovidesarewardingexperience,as
wellassupportforyourfavoritetunes.AudioCD-RandCD-RWdiscplaybackensures
compatibilitywithyourmusiccollection,andtheRCApreampoutputprovidestheright
connectionstoexpandyoursystem.Fromitsfrontpanelauxiliaryinputforconnectingyour
MP3player,tothedetachablefaceforsecurityassurance,thisheadunithasyoucovered.
4
7
5 6
8
101112131415161718
3
5
MD200 OPERATION
Control Locations - Remote
1
2
4
3
5
6
VolumeDown
Audio / Menu
Band
Tune/TrackDown
1
2
3
4
5
6
7
8
9
Display
VolumeUp
Power/Mute
Source
Tune/TrackUp
8
9
7
6
MD200 OPERATION
General Operation
Press RELEASEandpullawayfromtheleftsidetoremove.
Tore-install,insertrightsideoffaceplatefirstthenpushleft
side to secure.
Removetrimringandinstallsupplied#1x7/32”Phillips
headscrewthroughleftsideofmountingframeinto
faceplate.
Press
 toturntheuniton.InsertingaCDwillturntheunit
onautomatically.Pressandholdforthreeseconds
 to
turntheunitoff.
Press MODEtoselectbetweenAM/FM,CDorauxiliary
input.Modesofoperationareindicatedinthedisplay.
Inserta3.5mmconnectorinthefrontpanelAUXport.
Connecttheotherendofthe3.5mmconnectortothe
headphoneoutputofanaudiodevice,MP3player,etc.Press
MODEtoselectAUXmode.
Adjustvolumeusingthe volume knob(00-46).
Theradiofrequency(tunermode)andCDtrack/elapsed
time(CDplayermode)willbeshownbydefault.Press
DISPtodisplaytheclock,andpressDISPagaintoreturnto
defaultdisplay.
PressandholdDISPfor2seconds,theclockwillbeginto
flash.PressTRACK
nn
toadjustthehoursandTRACK 
ll
toadjusttheminutes.PressDISPorwait5secondsto
savetheclocksettings.
Theclockwilldisplay12-hourAM/PMtimeinUSA
frequencyspacingmode(PM10:00).InEuropeanfrequency
spacingmode,theclockwilldisplay24-hourtime(22:00).
Pressandholdformorethan2secondstoRESETtheunit
uponinitialinstallation.TheRESETbuttonislocatedbehind
thefaceplate.
Faceplate Removal
Semi-permanent 
Faceplate Installation
Power On/Off
Mode
Auxiliary Input
Volume
Display
Set the Clock
12/24-hour Clock 
Reset
7
MD200 OPERATION
InserttheUSBconnectorofabatterypoweredUSBdevice
intotheUSBchargingportonthefrontpanel,which
provides5voltsDCand1.0amps.TheUSBdevicewill
immediatelybegincharging.
Note: TheUSBchargingportmaynotbecompatiblewith
everydeviceduetodifferencesinpowerrequirements.
Note:ThisUSBportprovidespoweronly,andwillnot
playbackmusicfromaUSBdevice.
Press AUDIOtoselectbetweenVolume(default),Bass,
Treble,Balance,FaderandEQ.
USB Charging Port
Audio
 
BASS VOLUME TREBLE BALANCE FADER
EQ
General Operation
PressandholdAUDIO/MENUformorethan3secondsto
accessthesetupmenu,thenpressAUDIO/MENUtocycle
throughmenuoptions.Whendesiredoptionappearsinthe
display,rotatethevolume knobleft/righttoadjustoractivate
thedesiredfunction.
Setup Menu
Menu Function Options Action
Loudness 
Curve
LOUD OFF Disablestheloudnessfunction.
LOUD ON
Enablestheloudnessfunction.Activatingthisfeature
willenhancethebassandtreblefrequencieswhen
listeningtomusicatlowvolumes.
Tuner
Frequency
Spacing
FREUSA
ProgramstheunittoUSAtunerspacing.
(200kHzforFMand10kHzforAM).(Tuner mode only)
FRE EU
ProgramstheunittoEuropeantunerspacing.
(50kHzforFMand9kHzforAM).(Tuner mode only)
Local/Distance 
Tuning
LOC OFF Activatesdistancetuning.
LOC ON Activateslocaltuningforstrongstationreceptiononly.
Clock 
Display
C
LK ON
Programsunittodisplaytheclockwhenthepoweris
off.
CLK OFF
Programsunittonotdisplaytheclockwhenthepower
is off.
Beep 
Confirmation
BEEP OFF Disablestheconfirmationbeep.
BEEPON Enablestheconfirmationbeep.
Illumination
Dimmer
ILLUHI ProgramstheLCDtothebrightestilluminationlevel.
ILLULO LowerstheLCDilluminationlevel.
8
MD200 OPERATION
Audio Operation
Press AUDIOuntilBASappears.
Rotatethevolume knobleft/righttoadjust.
(-6minimum/6maximum)
Press AUDIOuntilTREappears.
Rotatethevolume knobleft/righttoadjust.
(-6minimum/6maximum)
Press AUDIOuntilBALappears.
Rotatethevolume knobleft/righttoadjust.
(L12-R12)"BALR=L"representsequalbalance.
Press AUDIOuntilFADappears.
Rotatethevolume knobleft/righttoadjust.
(F12-R12)"FADR=F"representsequalbalance.
Press AUDIOuntilEQappears.Rotatevolumeknobleft/
righttoadjustbetweenPOP,CLS,ROCandOFF(default)
equalizationcurves.AnyadjustmenttotheBassorTreble
settingsautomaticallycancelsthecurrentEQcurve.
Press TUNE
nn
or TUNE 
ll
formorethan2secondsto
seektothenextstrongstation.
Press TUNE
nn
or TUNE 
ll
momentarilytochangethe
radiofrequencyupordownonestepatatime.Pressand
holdtoadvancequickly.
Press BANDformorethan2secondstoselectmonoor
stereo(default)receptionofthebroadcastsignal.
Press BANDtoselectbetweenFM1,FM2,FM3andAM1,
AM2 bands.
Upto18FMstationsand12AMstationscanbestored.
Tostoreastation,selectthedesiredbandandstation.
Pressandholdthedesiredpresetbuttonformorethan2
seconds.Whenstored,thepresetnumberwillappearinthe
display.Thestationcanberecalledanytimebypressingthe
correspondingpresetbutton.
Bass
Treble
Balance
Fader
Preset EQ Curves 
Seek Tuning
Manual Tuning
FM Stereo/Mono 
Band
Storing and Recalling  
Station Presets
Tuner Operation
9
MD200 OPERATION
CD Player Operation
Withthelabelfacingup,insertastandardsizeCDintothe
CDslot.TheCDwillautomaticallybeginplayback.
PresstheEJECTbuttontostopandejecttheCD.
Theunitwillchangetotunermode.
Press TRACK 
ll
toskiptothebeginningofthenexttrack.
Press TRACK
nn
toreturntothebeginningofthecurrent
track.PressingTRACK
nn
againskipstothebeginningof
theprevioustrack.
PressandholdTRACK 
ll
or TRACK
nn
tofastforward
orreverseatrack.
Press
l
/
II
totemporarilystopCDplayback.
Press
l
/
II
againtoresumeplayback.
Press INTtoplaythefirst10secondsofeachtrack.
Press INT to cancel.
Press RPTtocontinuouslyrepeatselectedtrack.
Press RPT to cancel.
Press RDMtoplayalltracksinrandomorder.
Press RDMagaintocancel.
SomeCD-RsandCD-RWsmaybeincompatiblewiththis
unit,dependingonmediatypeandrecordingmethod.
Note: CD-Rrecordingsessionsmustbeclosed(finalized)for
playback.
Insert CD
Eject CD
Track Select
Fast Forward and 
Reverse
Pause
Intro
Repeat
Random
CD-R/CD-RW 
Compatibility
10
MD200 OPERATION
Limited One Year Warranty
Thiswarrantygivesyouspecificlegal
rights.Youmayalsohaveotherrights
whichvaryfromstatetostate.
DualElectronicsCorp.warrantsthis
producttotheoriginalpurchasertobefree
fromdefectsinmaterialandworkmanship
foraperiodofoneyearfromthedateof
theoriginalpurchase.
DualElectronicsCorp.agrees,atour
option,duringthewarrantyperiod,
torepairanydefectinmaterialor
workmanshiportofurnishanequal
new,renewedorcomparableproduct
(whicheverisdeemednecessary)in
exchangewithoutcharges,subjectto
verificationofthedefectormalfunctionand
proofofthedateofpurchase.Subsequent
replacementproductsarewarrantedfor
thebalanceoftheoriginalwarrantyperiod.
Who is covered?Thiswarrantyisextended
totheoriginalretailpurchaserforproducts
purchasedfromanauthorizedDualdealer
andusedintheU.S.A.
What is covered?Thiswarrantycoversall
defectsinmaterialandworkmanshipin
thisproduct.Thefollowingarenotcovered:
software,installation/removalcosts,
damageresultingfromaccident,misuse,
abuse,neglect,productmodification,
improperinstallation,incorrectline
voltage,unauthorizedrepairorfailure
tofollowinstructionssuppliedwiththe
product,ordamageoccurringduring
returnshipmentoftheproduct.Specific
licenseconditionsandcopyrightnoticesfor
thesoftwarecanbefoundviawww.dualav.
com.
What to do?
1.Beforeyoucallforservice,checkthe
troubleshootingguideinyourowner’s
manual.Aslightadjustmentofany
customcontrolsmaysaveyouaservice
call.
2.Ifyourequireserviceduringthe
warrantyperiod,youmustcarefully
packtheproduct(preferablyinthe
originalpackage)andshipitbyprepaid
transportationwithacopyoftheoriginal
receiptfromtheretailertoan
authorizedservicecenter.
3.Pleasedescribeyourproblemin
writingandincludeyourname,a
returnUPSshippingaddress(P.O.Box
notacceptable),andadaytimephone
numberwithyourshipment.
4.Formoreinformationandforthe
locationofthenearestauthorized
servicecenterpleasecontactusbyone
ofthefollowingmethods:
•Callustoll-freeat1-866-382-5476
•E-mailusat[email protected]
ExclusionofCertainDamages:This
warrantyisexclusiveandinlieuofany
andallotherwarranties,expressedor
implied,includingwithoutlimitationthe
impliedwarrantiesofmerchantabilityand
fitnessforaparticularpurposeandany
obligation,liability,right,claimorremedy
incontractortort,whetherornotarising
fromthecompany’snegligence,actual
orimputed.Nopersonorrepresentative
isauthorizedtoassumeforthecompany
anyotherliabilityinconnectionwiththe
saleofthisproduct.Innoeventshallthe
companybeliableforindirect,incidentalor
consequentialdamages.
11
MD200 OPERATION
FCC Compliance
ThisdevicecomplieswithPart15oftheFCCRules.Operationissubjecttothefollowingtwoconditions:
(1)thisdevicemaynotcauseharmfulinterference,and
(2)thisdevicemustacceptanyinterferencereceived,includinginterferencethatmaycauseundesiredoperation.
Warning:Changesormodificationstothisunitnotexpresslyapprovedbythepartyresponsibleforcompliance
couldvoidtheuser’sauthoritytooperatetheequipment.
Note:ThisequipmenthasbeentestedandfoundtocomplywiththelimitsforaClassBdigitaldevice,pursuantto
Part15oftheFCCRules.Theselimitsaredesignedtoprovidereasonableprotectionagainstharmfulinterference
inaresidentialinstallation.Thisequipmentgenerates,usesandcanradiateradiofrequencyenergyand,ifnot
installedandusedinaccordancewiththeinstructions,maycauseharmfulinterferencetoradiocommunications.
However,thereisnoguaranteethatinterferencewillnotoccurinaparticularinstallation.Ifthisequipmentdoes
causeharmfulinterferencetoradioortelevisionreception,whichcanbedeterminedbyturningtheequipmentoff
andon,theuserisencouragedtotrytocorrecttheinterferencebyoneormoreofthefollowingmeasures:
• Reorientorrelocatethereceivingantenna.
• Increasetheseparationbetweentheequipmentandreceiver.
• Connecttheequipmentintoanoutletonacircuitdifferentfromthattowhichthereceiverisconnected.
• Consultthedealeroranexperiencedradio/TVtechnicianforhelp.
Troubleshooting
Error Codes
Problem Cause Action
Unit will not turn on 
(no power)
Yellowwirenotconnectedorincorrectvoltage
Redwirenotconnectedorincorrectvoltage
Checkconnectionsforpropervoltage
(11~16VDC)
Blackwirenotconnected Checkconnectiontoground
Fuseblown Replacefuse
Unit has power 
(but no sound)
Speakerwiresnotconnected Checkconnectionsatspeakers
Oneormorespeakerwirestouchingeach
otherortouchingchassisground
Insulateallbarespeakerwiresfromeach
otherandchassisground
Unit blows fuses
Yelloworredwiretouchingchassisground Checkforpinchedwire
Speakerwirestouchingchassisground Checkforpinchedwire
Incorrectfuserating Usefusewithcorrectrating
Excessive skipping
Unitisnotmountedcorrectly
Checkmountingsleeveoraddabackstrap
support
Physicaldefectinmedia(CD,CD-RorCD-
RW) Checkmediaforscratches
Unit will not accept
a disc
CDmechanismpositionoutofalignment
Press EJECT for 3 seconds to reset
CDmechanismposition
CDtransitscrewsstillinplace
Remove2transitscrewslocatedontopof
theunit.
Error Code Cause Action
ER-1 appears on the display
Disc error
PressejectorRESET
ER-2 appears on the display
Mechanismerrorordiscisupsidedown PressejectorRESET
ER-3 appears on the display
ServoError PressejectorRESET
Specifications
Frequencyresponse:20Hz-20kHz
Channelseparation@1kHz:>65dB
D/Aconverter:1 Bit
Tuningrange:87.5MHz-107.9MHz
Usablesensitivity:12dBf
50dBquietingsensitivity:16dBf
Stereoseparation@1kHz:40dB
Frequencyresponse:30Hz-13kHz
Tuningrange:530kHz-1710kHz
Usablesensitivity:30uV
Frequencyresponse: 80Hz-2kHz
Speakeroutputimpedance: 4~8 ohms
Fuse:5 amp AGC
Dimensions:7" x 7" x 2" (178 x 178 x 51 mm)
Designandspecificationssubjecttochangewithoutnotice.
CDPlayer
FMTuner
AMTuner
General
CEA-2006 Power Standard Specifications
(reference:14.4VDC+/-0.2V,20Hz~20kHz)
PowerOutput:5WattsRMSx4channelsat4ohmsand<1%THD+N
Signaltonoiseratio:75dBA(reference:1wattinto4ohms)
DualElectronicsCorp.
TollFree:1-866-382-5476
www.dualav.com
©2011DualElectronicsCorp.Allrightsreserved.
NSA1111-V01
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12

Dual MCP200S User manual

Dual
Brand
Dual
Model
MCP200S
Category
Car media receivers
Type
User manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents