INSTRUCTION MANUAL
Smart ANPR Camera
Model: CC-2000NP
PRECAUTIONS TROUBLESHOOTING SPECIFICATION
■ Do not open or modify
Do not open the case except during maintenance and
installation, as it may be dangerous and cause damages.
■ Do not put objects inside the unit
Make sure that no metal objects or flammable substances
get inside the camera. It could cause a fire, short-circuits
or damages.
■ Be careful when handling the unit
To prevent damage, do not drop the camera or subject it
to strong shock or vibration.
■ Install away from electric or magnetic fields
■ Protect from humidity and dust
■ Protect from high temperature
Be careful when installing close to the ceiling , in a kitchen
or boiler room, as the temperature may rise to high levels.
■ Cleaning
Dirt can be removed from the case only by wiping it with
a soft cloth moistened with a soft detergent solution.
■ Mounting Surface
The mounting surface material must be strong enough to
support the camera.
ACCESSORY DIMENSION
CAMERA
General spec NTSC PAL
CCD type 1/3” 520K Pixels
Color
1/3” 610K Pixels
Color
Total number of pixel 1020(H) x 507(V) 1020(H) x 595(V)
Min illumination 0.14Lux (F1.2, 30IRE)
Resolution 650 TV Lines
Shutter speed 1/60s – 1/100,000s 1/50s – 1/100,000s
S/N ratio 50dB or more (AGC off)
Sync system Internal
Voltage DC 12[V] (10.0[V] ~ 16.0[V])
Power consumption Max 1.2[W]
Operating temp. -10˚C ~ +50˚C
Storage temp. -20˚C ~ +70˚C
Operating humidity Under 90% (Non-condensing)
HOUSING
Power supply DC12V Max 36W / AC24V Max 72W
IR angle 20˚(2PCS), 45˚ (2PCS), 60˚ (4PCS)
Control RS485 by wire, baud rate(9600) optional,
built in PELCO-D protocol
Built-in Blower / IR Lamp
Operating temp. -15˚C ~ +60˚C
Dimension 302mm x 136mm
Weight 2.0Kg
302mm 136mm
95mm
60mm 60mm 3-1/4 UNC
MOUNTING HOLE
76mm
98mm
INSTALLATION FOR BRACKET
Fix the screws
to the wall
!
Use UNC1/4 Screws
to fix the housing wit
h the mount!
CAMERA
wrench 3/16 ············································ 1ea
wrench screw ············································ 2ea
Spring washer ············································ 1ea
Flat washer ············································ 1ea
1” concord ············································ 2ea
Manual ············································ 1ea
BRACKET
Screw ············································ 4ea
Plastic anchor ············································ 4ea
Wrench ·············································1ea
Before installing and using the camera,
please read this manual carefully.
■ If no image appears
Is the coaxial cable attached securely?
Are the power and voltage normal?
Has the iris of the lens inside the camera been
adjusted correctly (with the level volume) ?
Is there adequate illumination?
■ If the image is unclear
Is the lens in focus?
Is the lens dirty?
Dirt or fingerprints on the lens can adversely affect the
images. Gently wipe any dirt or fingerprints off the lens
with a soft cloth or lens cleaning paper and cleaning
Fluid (commercially available).
Is the monitor adjusted correctly?
■ At using AC24V,
Min. 5A SMPS is recommended to use
DIP SW & CONTROL KEY SETTING OSD MENU
EXPOSURE COLOR
LENS MANUAL / DC WB MODE AWC / ATW / MANUAL / PUSH
BACKLIGHT OFF / BLC / HME / D.WDR RED GAIN 0 ~ 255
AGC OFF / LOW / MID / HIGH / HIGHEST BLUE GAIN 0 ~ 255
2D DNR OFF / LOW / MID / HIGH COLOR MODE NORMAL / COOL / WARM
DAY&NIGHT FUNCTION
D&N MODE AUTO / COLOR / B&W MIRROR OFF / MIRROR
NIGHT C. 0 ~ 100 SHARPNESS 0 ~ 30
NIGHT A. 0 ~ 100 GAMMA MANUAL / 0.45 / 0.6 / 1.0
SLC OFF / ON
NIGHT-UP OFF / ON
MOTION PRIVACY
AREA SET AREA 1~4 OFF / ON MASK1 OFF / ON
SENSITIV. 1 ~ 30 MASK2 OFF / ON
SHOW INDI. OFF / ICON / TRACE MASK3 OFF / ON
EXTER OUT OFF / ON MASK4 OFF / ON
MASK5 OFF / ON
MASK6 OFF / ON
MASK7 OFF / ON
MASK8 OFF / ON
SET UP EXIT
TILTLE OFF / ON SAVE & EXIT
DPC SET OFF / AUTO EXIT
MONITOR MODE 1 / MODE 2
LANGUAGE ENGLISH / 繁體中文 / 简体中文 /
日本語 / DEUTSCH / FRENCH /
ITALIAN / RUSSIAN / SPANISH / DUTCH
OSD COLOR BLUE / GREEN / CYAN / RED
MAGENTA / YELLOW / PURPLE / GRAY
COMMUNICA. OFF / ON
FACTORY SET NO / YES
RECOMMENDED SETTING
1. ADDRESS SETTING [SW1, SW2, SW3]
• SW1 ~ SW3 : address setting
2. LED PERFORMANCE SETTING [SW4, SW5]
• Adjust LED performance by DIP SW setting.
• Select the light you want to turn on.
• To adjust the LED brightness, press the “UP” “DOWN” key.
• For saving, press “SET” key
• After saving, make sure that SW4 & SW5 key to be replaced at ‘OFF’ position.
** CAUTION
If SW4 & SW5 are OFF without saving, it remains the previous light.
3. AUTO or B/W MODE [SW6]
• SW6 OFF : all LED turns on or off by CDS sensor
SW6 ON : LED ON mode at all time (B/W MODE)
** POWER LED
Light ON at power up, RED light blinking at normal LED operation.
1. B/W MODE SETTINGS (to capture front plate)
1-1. Camera mode setting (SW2) : OFF, OFF
1-2. Shutter speed : 1/1000
1-3. Gamma: 0.6
1-4. Installation distance: within 10M (Over 80% car image on the screen)
Installation location: 45˚ away from the front
2. Auto mode setting (normal mode)
2-1. Camera mode setting (SW2) : ON, OFF
2-2. Shutter speed : 1/50, 60
2-3. Gamma: 0.45
Camera Mode Setting SW6
B/W mode setting for capturing front plate (LED always on) ON
Auto mode setting for normal condition OFF
At SW4, SW5 off, press “SET” key to start OSD menu control.
ADDR. SW1 SW2 SW3
0 OFF OFF OFF
1 ON OFF OFF
2 OFF ON OFF
3 ON ON OFF
4 OFF OFF ON
5 ON OFF ON
6 OFF ON ON
7 ON ON ON
LED SEL SW4 SW5
Not OFF OFF
60° ON OFF
45° OFF ON
20° ON ON
SW6
OFF.
AUTO MODE
ON.
NIGHT MODE
/