GEIGER Remote radio receiver GRE001 Operating instructions

Brand: GEIGER

Model: Remote radio receiver GRE001

Category: Wall transmitters

Type: Operating instructions

This manual is also suitable for

Remote radio receiver GRE002

www.geiger.de EN

DE Original-Montage- und

Betriebsanleitung

Original assembly and

operating instructions

Notice originale de montage

et d’utilisation

Instrucciones originales de

instalación y funcionamiento

Istruzioni originali di installazione

e funzionamento

Remote radio receiver

GRE002

2Gerhard Geiger GmbH & Co. KG | 100W1653 0723V000en

Index

1. General .......................................................................................2

2. Warranty .....................................................................................2

3. Safetyinstructionsspecictoradioreceivers ......................2

4. Connection ................................................................................3

5. Operating modes ......................................................................3

6. Operation ...................................................................................3

7. Setting the intermediate position ............................................4

8. Reset to factory settings ..........................................................5

9. Technical data ...........................................................................6

10. Declaration of Conformity ........................................................ 6

11. Disposal notice .........................................................................6

1. General

Dear customer,

With the purchase of a GEIGER radio receiver you have decided on a quality product from

GEIGER.

Thank you for your decision and the condence you have placed in us.

2. Warranty

In the event of improper installation contrary to the operating instructions and/or structural

modication, the legal and contractual warranty for material defects and product liability shall

expire.

3. Safetyinstructionsspecictoradioreceivers

Avoid damage to the product:

fAvoid shocks.

fDo not drop the radio receiver.

fDo not immerse the radio receiver in liquids and protect it from splash water.

fDo not allow children to play with stationary controls.

fKeep radio receivers away from children.

www.geiger.de EN

4. Connection

5. Operating modes

There are two operating modes:

1. Roller shutter mode

2. Blind mode

The radio receiver is in roller shutter mode by default. After a reset, the operating mode is

always the roller shutter mode.

5.1 Changing the operating mode

1. Press the programming button for 6 seconds g after 3 seconds, the LED starts to ash

quickly, after 6 seconds the LED ashes slowly. As soon as the LED ashes slowly,

release the programming button.

2. Press the programming button again until the LED stops ashing (after 3 seconds).

3. Release the programming button, the operating mode has been changed.

5.2 Displaying the current operating mode

Press the programming button briey (< 1 second):

1x ashing g Shutter mode

2x ashing g Blind mode

6. Operation

6.1 Connectingthersthand-heldtransmitter

1. Connect receiver to drive.

2. Connect receiver to power g drive makes a clicking sound.

3. Press the UP and DOWN buttons on the hand-held transmitter imultaneously g drive

makes a clicking sound. The connection is completed.

6.2 Changing the direction of rotation

1. Press the PAIR button for > 5 seconds g drive makes a clicking sound.

2. Press the STOP key for > 2 seconds g drive makes a clicking sound, the direction of

rotation has been changed.

PAIR button

Status LED

EXTERNAL

SWITCH

VOLTAGE

230V~/50Hz

MOTOR

In1

In1In2Com

NNPEPEL

In2

Commen

4Gerhard Geiger GmbH & Co. KG | 100W1653 0723V000en

6.3 Connectingthesecondhand-heldtransmitter

Option 1:

1. Hand-held transmitter already taught-in: press PAIR button for > 5 seconds g drive

makes a clicking sound.

2. New hand-held transmitter: Press the PAIR button for > 2 seconds g drive makes a

clicking sound, the second hand-held transmitter is taught-in.

Option 2:

1. Press the PAIR button on the receiver for 3 seconds (until the LED ashes quickly).

2. Press any button on the hand-held transmitter to be taught-in for 3 seconds g drive

makes a clicking sound, the LED stops ashing.

6.4 Deletingahand-heldtransmitter

1. Hand -held transmitter that is NOT to be deleted: Press the PAIR button for > 5 seconds

g drive makes a clicking sound.

2. Hand-held transmitter that is to be deleted: Press the PAIR button for > 10 seconds

g Drive makes a clicking sound after 2 seconds and after 10 seconds, the hand

transmitter is deleted.

6.5 Replacingalosthand-heldtransmitter

1. Disconnect the receiver from the power supply for at least 2 seconds.

2. Reconnect the receiver to the mains for 10 seconds.

3. Disconnect the receiver from the power supply for at least 2 seconds.

4. Connect the receiver to the mains again. The drive makes a clicking sound.

5. Press the PAIR button on a new hand-held transmitter for at least 2 seconds.

The drive makes a clicking sound, the new hand-held transmitter is programmed.

I ATTENTION: The lost hand transmitter is still stored in the drive. If you

arenotsurewherethishandtransmitteris,allhand-heldtransmitters

can be deleted by resetting the radio receiver to the delivery state.

Resetting the radio receiver to the delivery status

1. Disconnect the receiver from the power supply for at least 2 seconds.

2. Reconnect the receiver to the mains for 10 seconds.

3. Disconnect the receiver from the power supply for at least 2 seconds.

4. Connect the receiver to the mains again. The drive makes a clicking sound.

5. Press the PAIR button on a hand-held transmitter that has already been programmed

for at least 7 seconds. The drive makes a clicking sound once after approx. 2 seconds

and a second time after approx. 7 seconds. The drive is reset to the delivery state.

7. Setting the intermediate position

It is possible to set two intermediate positions. The rst intermediate position is set from the

upper end position, the second from the lower end position.

In roller shutter mode, no intermediate position is taught-in in the delivery state.

In blind mode, a lower intermediate position is stored in the delivery state. This position is just

above the lower end position (slats slightly open).

Setting/changing the upper intermediate position

1. Move the drive to the upper end position.

2. Press the STOP and DOWN buttons simultaneously for at least 2 seconds g The drive

moves down.

3. Once the desired intermediate position has been reached, release both buttons g

The drive stops.

4. The position can be adjusted with the UP and DOWN buttons.

5. Press the STOP button for at least 5 seconds g The drive makes a clicking sound,

the upper intermediate position is stored.

www.geiger.de EN

Setting/changing the lower intermediate position

1. Move the drive to the lower end position.

2. Press the STOP and UP buttons simultaneously for at least 2 seconds g The drive

moves upwards.

3. Once the desired intermediate position has been reached, release both buttons g

The drive stops.

4. The position can be adjusted with the UP and DOWN buttons.

5. Press the STOP button for at least 5 seconds g The drive makes a clicking sound and

the lower intermediate position is saved.

If no new intermediate position is saved within 180 seconds, the existing intermediate

position is deleted and the receiver returns to its original position.

7.7 Move to intermediate position

Roller shutter mode

Drive is in the upper end position

1. Press the STOP button briey (< 1 second) g The drive moves to the upper inter-

mediate position.

Drive is in the lower end position

1. Press the STOP button briey (< 1 second) g The drive moves to the lower inter-

mediate position.

Blind mode

Drive is in the upper end position

1. Press the STOP button briey (< 1 second) g The drive moves to the lower end

position and opens the slats by 45° (lower intermediate position).

2. Press the DOWN button briey (< 1 second) g The drive moves to the upper

intermediate position (slats closed).

3. Briey press the DOWN button twice (< 1 second) g The drive moves to the upper

intermediate position and opens the slats by 45°.

4. Press the DOWN button for longer than 1 second g The drive moves to the lower end

position (slats closed).

Drive is in the lower end position

1. Press the STOP button briey (< 1 second) g The drive opens the slats by 45°

(lower intermediate position).

8. Reset to factory settings

Press the PAIR button on the external radio receiver for > 10 seconds g After 3 seconds the

LED ashes quickly, after 6 seconds the LED ashes slowly, after 10 seconds the LED switches

off, the receiver is reset.

6Gerhard Geiger GmbH & Co. KG | 100W1653 0723V000en

For technical questions, please call our service team at: +49 (0) 7142 938 333.

They will be happy to assist you.

Gerhard Geiger GmbH & Co. KG

Schleifmühle 6 | D-74321 Bietigheim-Bissingen

T +49 (0) 7142 9380 | F +49 (0) 7142 938 230

info@geiger.de | www.geiger.de

9. Technical data

Transmitting frequency 433,92 MHz

Transmitting power 6 dBm

Temperature range -0°C to +60°C

Protection class IP54

Dimensions 95 x 42 x 20 mm

Subject to technical modifications

10. Declaration of Conformity

The receiver complies with the technical regulations of the European Community, carries the

CE mark and can be used in all EU countries and Switzerland without registration.

The declaration of conformity for the handheld transmitter can be found at www.geiger.de

11. Disposal notice

Disposal of packaging materials

Packaging materials are raw materials and can therefore be reused. Please dispose of them

properly in the interest of environmental protection.

Disposal of electrical and electronic equipment

According to the EU Directive, electrical and electronic equipment must be collected and

disposed of separately.

GEIGER Remote radio receiver GRE001 Operating instructions

Brand: GEIGER

Model: Remote radio receiver GRE001

Category: Wall transmitters

Type: Operating instructions

This manual is also suitable for

Remote radio receiver GRE002

Download PDF

report

GEIGER Remote radio receiver GRE001 Operating instructions

This manual is also suitable for

GEIGER Remote radio receiver GRE001 Operating instructions

Related papers

Other documents